Characteristics and structural change of layered polysilane (Si6H6) anode for lithium ion batteries

Layered polysilane (Si₆H₆) has a graphite-like structure with higher capacity than crystalline silicon. The rate of increase of the thickness of a layered polysilane electrode after 10 charge-discharge cycles was smaller than that for a Si powder electrode, although the layered polysilane electrode has higher capacity. The structural changes of electrochemically lithiated and delithiated layered polysilane at room temperature were studied using scanning electron microscopy, X-ray diffraction and Raman spectroscopy. Layered polysilane became amorphous by insertion of lithium to 0 V, whereas insertion of lithium into crystalline silicon produces Li₁₅Si_4. Layered polysilane maintained an amorphous state during lithium insertion and deinsertion, whereas silicon changed between Li₁₅Si₄ and amorphous Li_xSi, which explains the smaller volume change of a layered polysilane electrode compared with a Si powder electrode.     

Surface structural disordering in graphite upon lithium intercalation/deintercalation

We report on the origin of the surface structural disordering in graphite anodes induced by lithium intercalation and deintercalation processes. Average Raman spectra of graphitic anodes reveal that cycling at potentials that correspond to low lithium concentrations in Li_xC (0 ≤ x < 0.16) is responsible for most of the structural damage observed at the graphite surface. The extent of surface structural disorder in graphite is significantly reduced for the anodes that were cycled at potentials where stage-1 and stage-2 compounds (x > 0.33) are present. Electrochemical impedance spectra show larger interfacial impedance for the electrodes that were fully delithiated during cycling as compared to electrodes that were cycled at lower potentials (U < 0.15 V vs. Li/Li⁺). Steep Li⁺ surface-bulk concentration gradients at the surface of graphite during early stages of intercalation processes, and the inherent increase of the Li_xC d-spacing tend to induce local stresses at the edges of graphene layers, and lead to the breakage of C-C bonds. The exposed graphite edge sites react with the electrolyte to (re)form the SEI layer, which leads to gradual degradation of the graphite anode, and causes reversible capacity loss in a lithium-ion battery.     

Electrochemical behaviour of Heusler alloy Co2MnSi for secondary lithium batteries

Electrochemical lithiation of Co₂MnSi with a Heusler structure is investigated as a candidate negative electrode (anode) material for secondary lithium batteries. The electrode maintains a reversible discharge capacity of 112 mAh g⁻¹ for 50 cycles when cycled between 0.01 and 3 V. It is proposed that the lithiation mechanism consists of two steps. Co₂MnSi transforms to Heusler-type Li₂MnSi during the first charge cycle and subsequent charge–discharge cycles involve the formation of a solid solution in Li_xMnSi. The latter compound maintains its structural integrity throughout cycling to provide steady cycling behaviour. Magnetic measurements are also employed to substantiate further the structural changes during electrochemical cycling.     

Synthesis of LixMnO2 by chemical lithiation in an aqueous media

Li_xMnO₂ (x = 0.302) was synthesized by chemical lithiation, using a formaldehyde reducing agent and a LiOH lithium source in an aqueous media. The electrochemical properties and structural stability of the product were characterized by X-ray diffraction and charge-discharge measurements. The chemically lithiated Li_xMnO₂ had a first charge and discharge capacity of 86.2 and 265 mAh/g, respectively, with good cycling behavior. Based on the electrochemical results of the first charge, a two-step mechanism of Li_xMnO₂ lithiation is proposed. γ-MnO₂ is first oxidized by formaldehyde, and then Li diffuses into the γ-MnO₂ lattice.     

Fabrication and electrochemical characterization of a vertical array of MnO2 nanowires grown on silicon substrates as a cathode material for lithium rechargeable batteries

A complementary metal-oxide-semiconductor (CMOS) compatible process for fabricating on-chip microbatteries based on nanostructures has been developed by growing manganese dioxide nanowires on silicon dioxide (SiO₂)/silicon (Si) substrate as a cathode material for lithium rechargeable batteries. High aspect-ratio anodized aluminum oxide (AAO) template integrated on SiO₂/Si substrates can be exploited for fabrication of a vertical array of nanowires having high surface area. The electrolytic manganese dioxide (EMD) nanowires are galvanostatically synthesized by direct current (dc) electrodeposition. The microstructure of these nanowire arrays is investigated by scanning electron microscopy and X-ray diffraction. Their electrochemical tests show that the discharge capacity of about 150 mAh g⁻¹ is maintained during a few cycles at the high discharge/charge rate of 300 mA g⁻¹.     

Nanosized Li4Ti5O12/graphene hybrid materials with low polarization for high rate lithium ion batteries

We report a simple strategy to prepare a hybrid of lithium titanate (Li₄Ti₅O₁₂, LTO) nanoparticles well-dispersed on electrical conductive graphene nanosheets as an anode material for high rate lithium ion batteries. Lithium ion transport is facilitated by making pure phase Li₄Ti₅O₁₂ particles in a nanosize to shorten the ion transport path. Electron transport is improved by forming a conductive graphene network throughout the insulating Li₄Ti₅O₁₂ nanoparticles. The charge transfer resistance at the particle/electrolyte interface is reduced from 53.9 Ω to 36.2 Ω and the peak currents measured by a cyclic voltammogram are increased at each scan rate. The difference between charge and discharge plateau potentials becomes much smaller at all discharge rates because of lowered polarization. With 5 wt.% graphene, the hybrid materials deliver a specific capacity of 122 mAh g⁻¹ even at a very high charge/discharge rate of 30 C and exhibit an excellent cycling performance, with the first discharge capacity of 132.2 mAh g⁻¹ and less than 6% discharge capacity loss over 300 cycles at 20 C. The outstanding electrochemical performance and acceptable initial columbic efficiency of the nano-Li₄Ti₅O₁₂/graphene hybrid with 5 wt.% graphene make it a promising anode material for high rate lithium ion batteries.     

Synthesis of single crystalline Li0.44MnO2 nanowires with large specific capacity and good high current density property for a positive electrode of Li ion battery

The fabrication of single crystalline Li_0.44MnO₂ nanowires for the positive electrode of lithium ion battery is reported. The single crystalline Li_0.44MnO₂ nanowires are obtained by lithium exchange reaction of Na_0.44MnO₂ nanowires with high aspect ratio. The Li_0.44MnO₂ nanowires indicate both the large specific capacity of around 250 mAh g⁻¹ (1.5-4.5 V vs. Li/Li⁺) and the good high current density property for the positive electrode of lithium ion battery.     

Structural evolution of ramsdellite-type LixTi2O4 upon electrochemical lithium insertion–deinsertion (0 ≤ x ≤ 2)

Structural evolution during topotactical electrochemical lithium insertion and deinsertion reactions in ramsdellite-like Li_xTi₂O₄ has been followed by means of in situ X-ray diffraction techniques. The starting Li_xTi₂O₄ (x = 1) exists as a single phase with variable composition which extends in the range 0.50 ≤ x ≤ 1.33. However, beyond the lower and upper compositional limits, two other single phases, with ramsdellite-like structure, are detected. The composition of these single phases are: TiO₂ upon lithium deinsertion and Li₂Ti₂O₄ upon lithium insertion. Both TiO₂ and Li₂Ti₂O₄ are characterized by narrow compositional ranges. The close structural relationship between pristine LiTi₂O₄ and the inserted and deinserted compounds together with the relative small volume change over the whole insertion–deinsertion range (not more than 1.1% upon reduction) is a guaranty for the high capacity retention after long cycling in lithium batteries. The small changes in cell parameters well reflect the remarkable flexibility of the ramsdellite framework against lithiation and delithiation reactions.     

Improvement of cycle behaviour of SiO/C anode composite by thermochemically generated Li4SiO4 inert phase for lithium batteries

A new anode composite material is prepared by thermal treatment of a blend made of silicon monoxide (SiO) and lithium hydroxide (LiOH) at 550 °C followed by ball milling with graphite. X-ray diffraction pattern confirms the presence of Li₄SiO₄ in the thermally treated (SiO + LiOH) material. The electrode appears to be smooth and glassy as evident from observation with a scanning electron microscope (SEM), possibly due to the presence of nano-silicon and Li₄SiO₄ particles, and exhibits superior performance with a charge capacity of ∼333 mAh g⁻¹ at the 100th cycle with a low-capacity fade on cycling. Cyclic voltammograms of the electrode predict high power capability. On the other hand, the electrode comprising of only SiO and C prepared through ball milling, devoid of Li₄SiO_4, shows hard crust particulates in the electrode exhibiting low charge–discharge capacities with cycling.     

Electrochemical performance of VOMoO4 as negative electrode material for Li ion batteries

Polycrystalline samples of VOMoO₄ are prepared by a solid-state reaction method and their electrochemical properties are examined in the voltage window 0.005–3 V versus lithium. The reaction mechanism of a VOMoO₄ electrode for Li insertion/extraction is followed by ex situ X-ray diffraction analysis. During initial discharge, a large capacity (1280 mAh g⁻¹) is observed and corresponds to the reaction of ∼10.3 Li. The ex situ XRD patterns indicate the formation of the crystalline phase Li₄MoO₅ during the initial stages of discharge, which transforms irreversibly to amorphous phases on further discharge to 0.005 V. On cycling, the reversible capacity is due to the extraction/insertion of lithium from the amorphous phases. A discharge capacity of 320 mAh g⁻¹ is obtained after 80 cycles when cycling is performed at a current density of 120 mA g⁻¹.     

The synthesis and lithium intercalation electrochemistry of VO2(B) ultra-thin nanowires

Ultra-thin (<10 nm diameter) VO₂(B) nanowires have been synthesised, characterised structurally and morphologically and their lithium intercalation electrochemistry investigated. The wires exist in bundles and exhibit significant preferred orientation. They have a capacity to intercalate lithium of 265 mAh g⁻¹ (Li_0.82VO₂(B)) at a rate of 10 mA g⁻¹ compared with thicker wires of 50–100 nm diameter which exhibit a capacity of 200 mAh g⁻¹ at the same rate. The load curves, structure and morphology remain stable on cycling.     

Synthesis and electrochemical performance of Li2CoSiO4 as cathode material for lithium ion batteries

Li₂CoSiO₄ has been prepared successfully by a solution route or hydrothermal reaction for the first time, and its electrochemical performance has been investigated primarily. Reversible extraction and insertion of lithium from and into Li₂CoSiO₄ at 4.1 V versus lithium have shown that this material is a potential candidate for the cathode in lithium ion batteries. At this stage reversible electrochemical extraction was limited to 0.46 lithium per formula unit for the Li₂CoSiO₄/C composite materials, with a charge capacity of 234 mAh g⁻¹ and a discharge capacity of 75 mAh g⁻¹.     

NiSb2 as negative electrode for Li-ion batteries: An original conversion reaction

The study of the electrochemical reaction mechanism of lithium with NiSb₂ intermetallic material is reported here. The nickel diantimonide prepared by classic ceramic route is proposed as possible candidate for anodic applications in Li-ion batteries. The electrochemical characterisation of NiSb₂ versus Li⁺/Li⁰ shows a reversible uptake of 5 lithium per formula unit, which leads to reversible capacities of 500 mAh g⁻¹ at an average potential of 0.9 V. From ex situ XRD and ¹²¹Sb Mössbauer measurements it was shown that during the first discharge the orthorhombic NiSb₂ phase undergoes a pure conversion process (NiSb₂ + 6 Li⁺ + 6e⁻ → Ni⁰ + 2Li₃Sb). During the charge process that follows, the lithium extraction from the composite electrode takes place through an original conversion process, leading to the formation of the high pressure NiSb₂ polymorph. This highly reversible mechanism makes it possible to sustain 100% of the specific capacity after 15 cycles.     

Formation of the high lithium ion conducting phase from mechanically milled amorphous Li2S-P2S5 system

The fast ionic conducting structure similar to thio-Lithium Super Ionic Conductor (LISICON) phase is synthesized in the Li₂S-P₂S₅ system. The Li₂S-P₂S₅ glass-ceramics with the composition of xLi₂S·(100−x)P₂S₅ (75 ≤ x ≤ 80) are prepared by the heat-treatment of mechanically milled amorphous sulfide powders. In the binary Li₂S-P₂S₅ system, 78.3Li₂S·21.7P₂S₅ glass ceramic prepared by mechanical milling and subsequent heat-treatment at 260 °C for 3 h shows the highest conductivity of 6.3 × 10⁻⁴ S cm⁻¹ at room temperature and the lowest activation energy for conduction of 30.5 kJ mol⁻¹. The enhancement of conductivity with increasing x up to 78.3 is probably caused by the introduction of interstitial lithium ions at the Li sites which affects the Li ion distribution. The prepared electrolyte exhibits the lithium ion transport number of almost unity and voltage stability of 5 V vs. Li at room temperature.     

Influence of surface modification of LiCoO2 by organic compounds on electrochemical and thermal properties of Li/LiCoO2 rechargeable cells

LiCoO₂ is the most famous positive electrode (cathode) for lithium ion cells. When LiCoO₂ is charged at high charge voltages far from 4.2 V, cycleability of LiCoO₂ becomes worse. Causes for this deterioration are instability of pure LiCoO₂ crystalline structure and an oxidation of electrolyte solutions LiCoO₂ at higher charge voltages. This electrolyte oxidation accompanies with the partial reduction of LiCoO₂. We think more important factor is the oxidation of electrolyte solutions. In this work, influence of 10 organic compounds on electrochemical and thermal properties of LiCoO₂ cells was examined as electrolyte additives. As a base electrolyte solution, 1 M (M: mol L⁻¹) LiPF₆-ethylene carbonate (EC)/ethylmethyl carbonate (EMC) (mixing volume ratio = 3:7) was used. These compounds are o-terphenyl (o-TP), Ph-X (CH₃)_n (n = 1 or 2, X = N, O or S) compounds, adamantyl toluene compounds, furans and thiophenes. These additives had the oxidation potentials (Eox) between 3.4 and 4.7 V vs. Li/Li⁺. These Eox values were lower than that (6.30 V vs. Li/Li⁺) of the base electrolyte. These additives are oxidized on LiCoO₂ during charge of the LiCoO₂ cells. Oxidation products suppress the excess oxidation of electrolyte solutions on LiCoO₂. As a typical example of these organic compounds, o-TP (Eox: 4.52 V) was used to check the fundamental properties of these organic additives. Charge-discharge cycling tests were carried out for the Li/LiCoO₂ cells with and without o-TP. Constant current charge at 4.5 V is mainly used as a charge method. Cells with 0.1 wt.% o-TP exhibited slightly better cycling performance and lower polarization than those without additives. Lower polarization arises from a decrease in a resistance of interface between electrolyte solutions and LiCoO₂ by surface film formation resulted from oxidation of o-TP. Oxidation products were found by mass spectroscopy analysis to be mixture of several polycondensation compounds made from two to four terphenly monomers. Thermal stability of LiCoO₂ with electrolyte solutions did not improve by addition of o-TP. Slightly better charge-discharge cycling properties were obtained by using organic modifiers. However, when industrial applications were considered, drastic improvements have not been obtained yet. One of reasons may be too large influence of the deterioration of stability of pure LiCoO₂ structure at high voltage charging for industrial use. We hope to realize the tremendous improvements of high energy, long cycle life and safe lithium cells by the combination of both LiCoO₂ with more stable structure such as LiCoO₂ treated with MgO and new organic additives with molecular structure more carefully designed.     

Electrochemical behaviors of a Li3N modified Li metal electrode in secondary lithium batteries

A lithium conductive Li₃N film is successfully prepared on Li metal surface by the direct reaction between Li and N₂ gas at room temperature. X-ray diffraction (XRD), Auger electron spectroscopy (AES), cyclic voltammetry (CV), scanning electron microscopy (SEM), AC impedance, cathodic polarization and galvanostatic charge/discharge cycling tests are applied to characterize the film. The experimental results show that the Li₃N protective film is tight and dense with high stability in the electrolyte. Its thickness is more than 159.4 nm and much bigger than that of a native SEI film formed on the lithium surface as received. An exchange current as low as 3.244 × 10⁻⁷ A demonstrates the formation of a complete SEI film at the electrode|electrolyte interface with Li₃N modification. The SEI film is very effective in preventing the corrosion of the Li electrode in liquid electrolyte, leading to a decreased Li|electrolyte interface resistance and an average short distance of 3.16 × 10⁻³ cm for Li ion diffusion from electrolyte to Li surface. The Li cycling efficiency depends on N₂ exposing time and is obviously enhanced by the Li₃N (1 h) modification. After cycling, a dense and homogeneous Li layer deposits on the Li₃N (1 h) modified Li surface, instead of a loose and inhomogeneous layer on the Li surface as received.     

Nano-sized SiOx/C composite anode for lithium ion batteries

Nano-sized SiO_x/C composite with core-shell structure is prepared by a modified Stöber method. After heat-treatment, the O/Si ratio in SiO_x/C composite is near 1 and the core of SiO_x presents a structure composing of amorphous Si clusters and ordered SiO₂ domains. SiO_x/C composite anode shows high specific capacity (ca. 800 mAh g⁻¹), excellent cycling stability, good rate-capability but low initial coulombic efficiency. Li₂O and Li₄SiO₄ may generate in the initial lithiation process, which, combining with the carbon shell, can buffer the volume change caused by the alloying of Si with Li, and thereby improving the cycling stability of electrode. The nano feature of SiO_x/C particle and the electronic conductive nature of carbon coating layer ensure the good rate-capability of SiO_x/C electrode.     

Factors affecting the electrochemical reactivity vs. lithium of carbon-free LiFePO4 thin films

The electrochemical stability of various current collector materials such as Si, Pt, 304 stainless steel, Ti, Al exposed to the most common lithium-ion electrolyte salts (LiPF₆, LiBF₄, LiAsF₆, LiTFSI, LiClO₄) have been herein investigated. For applied potentials greater than 3 V, the acidic fluorine-based electrolytes were shown to be the most corrosive. Consequently, aqueous and non-aqueous electrolytes (1 M LiNO₃/H₂O vs. 1 M LiClO₄/EC-DMC) were successfully applied to study the electrochemical properties of C-free LiFePO₄ thin films whose redox potential is near 3.5 V vs. Li⁺/Li⁰. Using aqueous electrolyte has resulted in a lowering of both cell resistance and interfacial charge transfer resistance by almost one order of magnitude, hence enabling to considerably increase the electrochemical capacity of our LiFePO₄ thin films. Besides, we unravel the importance of the mechanical strains at the substrate/LiFePO₄ thin film interface on the film textural, structural modification and electrochemical stability upon cycling.     

Effect of Cr doping on the structural,electrochemical properties of Li[Li0.2Ni0.2−x/2Mn0.6−x/2Crx]O2 (x = 0, 0.02, 0.04, 0.06, 0.08) as cathode materials for lithium secondary batteries

Prospective positive-electrode (cathode) materials for a lithium secondary battery, viz., Li[Li_0.2Ni_0.2−x/2Mn_0.6−x/2Cr_x]O₂ (x = 0, 0.02, 0.04, 0.06, 0.08), were synthesized using a solid-state pyrolysis method. The structural and electrochemical properties were examined by means of X-ray diffraction, cyclic voltammetry, SEM and charge–discharge tests. The results demonstrated that the powders maintain the α-NaFeO₂-type layered structure regardless of the chromium content in the range x ≤ 0.08. The Cr doping of x = 0.04 showed improved capacity and rate capability comparing to undoped Li[Li_0.2Ni_0.2Mn_0.6]O₂. ac impedance measurement showed that Cr-doped electrode has the lower impedance value during cycling. It is considered that the higher capacity and superior rate capability of Cr-doping samples would be ascribed to the reduced resistance of the electrode during cycling.     

Vapor-induced solid-liquid-solid process for silicon-based nanowire growth

Silicon-based nanowires have been grown from commercial silicon powders under conditions with different oxygen and carbon activities. Nanowires grown in the presence of carbon sources consisted of a crystalline SiC core with an amorphous SiO_x shell. The thickness of the SiO_x shell decreased as the oxygen concentration in the precursor gases decreased. Nanowires grown in a carbon-free environment consisted of amorphous silicon oxide with a typical composition of SiO_1.8. The growth rate of nanowires decreased with decreasing oxygen content in the precursor gases. SiO_1.8 nanowires exhibited an initial discharge capacity of ∼1300 mAh g⁻¹ and better stability than those of silicon powders. A vapor-induced solid-liquid-solid (VI-SLS) mechanism is proposed to explain the nanowire growth (including silicon and other metal-based nanowires) from powder sources. In this approach, both a gas source and a solid-powder source are required for nanowire growth. This mechanism is consistent with experimental observations and also can be used to guide the design and growth of other nanowires.