Novel synthesis of LiFePO4-Li3V2(PO4)3 composite cathode material by aqueous precipitation and lithiation

LiFePO₄-Li₃V₂(PO₄)₃ composite cathode material is synthesized by aqueous precipitation of FeVO₄·xH₂O from Fe(NO₃)₃ and NH₄VO₃, following chemical reduction and lithiation with oxalic acid as the reducer and carbon source. Samples are characterized by XRD, SEM and TEM. XRD pattern of the compound synthesized at 700 °C indicates olivine-type LiFePO₄ and monoclinic Li₃V₂(PO₄)₃ are co-existed. TEM image exhibits that LiFePO₄-Li₃V₂(PO₄)₃ particles are encapsulated with a carbon shell 5-10 nm in thickness. The LiFePO₄-Li₃V₂(PO₄)₃ compound cathode shows good electrochemical performance, and its discharge capacity is about 139.1 at 0.1 C, 135.5 at 1 C and 116 mA h g⁻¹ at 3 C after 30 cycles.     

Effect of synthesis temperature on the properties of LiFePO4/C composites prepared by carbothermal reduction

LiFePO₄/C composite cathode materials were synthesized by carbothermal reduction method using inexpensive FePO₄ as raw materials and glucose as conductive additive and reducing agent. The precursor of LiFePO₄/C was characterized by differential thermal analysis and thermogravimetry. The microstructure and morphology of the samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM) and particle size analysis. Cyclic voltammetry (CV) and charge/discharge cycling performance were used to characterize their electrochemical properties. The results showed that the LiFePO₄/C composite synthesized at 650 °C for 9 h exhibited the most homogeneous particle size distribution. Residual carbon during processing was coated on LiFePO₄, resulting in the enhancement of the material's electronic properties. Electrochemical measurements showed that the discharge capacity first increased and then decreased with the increase of synthesis temperature. The optimal sample synthesized at 650 °C for 9 h exhibited a highest initial discharge capacity of 151.2 mA h g⁻¹ at 0.2 C rate and 144.1 mA h g⁻¹ at 1 C rate with satisfactory capacity retention rate.     

Synthesis of LiFePO4/C composite with high-rate performance by starch sol assisted rheological phase method

LiFePO₄/C composite was synthesized at 600 °C in an Ar atmosphere by a soluble starch sol assisted rheological phase method using home-made amorphous nano-FePO₄ as the iron source. XRD, SEM and TEM observations show that the LiFePO₄/C composite has good crystallinity, ultrafine sphere-like particles of 100-200 nm size and in situ carbon. The synthesized LiFePO₄ could inherit the morphology of FePO₄ precursor. The electrochemical performance of the LiFePO₄ by galvanostatic cycling studies demonstrates excellent high-rate cycle stability. The Li/LiFePO₄ cell displays a high initial discharge capacity of more than 157 mAh g⁻¹ at 0.2C and a little discharge capacity decreases from the first to the 80th cycle (>98.3%). Remarkably, even at a high current density of 30C, the cell still presents good cycle retention.     

Morphological characterization of LiFePO4/C composite cathode materials synthesized via a carboxylic acid route

A new type of LiFePO₄/C composite surrounded by a web containing both amorphous and crystalline carbon phases was synthesized by incorporating malonic acid as a carbon source using a high temperature solid-state method. SEM, TEM/SAED/EDS and HRTEM were used to analyze surface morphology and confirmed for the first time that crystalline carbon was present in LiFePO₄/C composites. The composite was effective in enhancing the electrochemical properties such as capacity and rate capability, because its active component consists of nanometer-sized particles containing pores with a wide range of sizes. An EDS elemental map showed that carbon was uniformly distributed on the surface of the composite crystalline particles. TEM/EDS results clearly show a dark region that is LiFePO₄ with a trace of carbon and a gray region that is carbon only. To evaluate the materials’ electrochemical properties, galvanostatic cycling and conductivity measurements were performed. The best cell performance was delivered by the material coated with 60 wt.% malonic acid, which delivered first cycle discharge capacity of 149 mAh g⁻¹ at a C/5 rate and sustained 222 cycles at 80% of capacity retention. When carboxylic acid was used as a carbon source to produce LiFePO₄, overall conductivity increased from 10⁻⁵ to 10⁻⁴ S cm⁻¹, since particle growth was prevented during the final sintering process.     

Synthesis and electrochemical properties of olivine LiFePO4 prepared by a carbothermal reduction method

LiFePO₄/C composite cathode material was prepared by carbothermal reduction method, which uses NH₄H₂PO₄, Li₂CO₃ and cheap Fe₂O₃ as starting materials, acetylene black and glucose as carbon sources. The precursor of LiFePO₄/C was characterized by differential thermal analysis and thermogravimetry. X-ray diffraction (XRD), scanning electron microscopy (SEM) micrographs showed that the LiFePO₄/C is olivine-type phase, and the addition of the carbon reduced the LiFePO₄ grain size. The carbon is dispersed between the grains, ensuring a good electronic contact. The products sintered at 700 °C for 8 h with glucose as carbon source possessed excellent electrochemical performance. The synthesized LiFePO₄ composites showed a high electrochemical capacity of 159.3 mAh g⁻¹ at 0.1 C rate, and the capacity fading is only 2.2% after 30 cycles.     

Synthesis and electrochemical characterization of carbon-coated nanocrystalline LiFePO4 prepared by polyacrylates-pyrolysis route

A carbon-coated nanocrystalline LiFePO₄ cathode material was synthesized by pyrolysis of polyacrylate precursor containing Li⁺, Fe³⁺ and PO₄⁻. The powder X-ray diffraction (XRD) and high-resolution TEM micrographs revealed that the LiFePO₄/C composite as prepared has a core-shell structure with pure olivine LiFePO₄ crystallites as cores and intimate carbon coating as a shell layer. Between the composite particulates, there exists a carbon matrix binding the nanocrystallites together into micrometer particles. The electrochemical measurements demonstrated that the LiFePO₄/C composite with an appropriate carbon content can deliver a very high discharge capacity of 157 mAh g⁻¹ (>92% of the theoretical capacity of LiFePO₄) with 95% of its initial capacity after 30 cycles. Since this preparation method uses less costly materials and operates in mild synthetic conditions, it may provide a feasible way for industrial production of the LiFePO₄/C cathode materials for the lithium-ion batteries.     

Study of LiFePO4 cathode materials coated with high surface area carbon

LiFePO₄ is a potential cathode material for 4 V lithium-ion batteries. Carbon-coated lithium iron phosphates were prepared using a high surface area carbon to react precursors through a solid-state process, during which LiFePO₄ particles were embedded in amorphous carbon. The carbonaceous materials were synthesized by the pyrolysis of peanut shells under argon, where they were carbonized in a two-step process that occurred between 573 and 873 K. The shells were also treated with a proprietary porogenic agent with the goal of altering the pore structure and surface area of the pyrolysis products. The electrochemical properties of the as-prepared LiFePO₄/C composite cathode materials were systematically characterized by X-ray diffraction, scanning electron microscope, element mapping, energy dispersive spectroscopy, Raman spectroscopy, and total organic carbon (TOC) analysis. In LiFePO₄/C composites, the carbon not only increases rate capability, but also stabilizes capacity. In fact, the capacity of the composites increased with the specific surface area of carbon. The best result was observed with a composite made of 8.0 wt.% with a specific surface area of 2099 m² g⁻¹. When high surface area carbon was used as a carbon source to produce LiFePO₄, overall conductivity increased from 10⁻⁸ to 10⁻⁴ S cm⁻¹, because the inhibition of particle growth during the final sintering process led to greater specific capacity, improved cycling properties and better rate capability compared to a pure olivine LiFePO₄ material.     

Synthesis of carbon-coated LiFePO4 nanoparticles with high rate performance in lithium secondary batteries

A novel preparation technique was developed for synthesizing carbon-coated LiFePO₄ nanoparticles through a combination of spray pyrolysis (SP) with wet ball milling (WBM) followed by heat treatment. Using this technique, the preparation of carbon-coated LiFePO₄ nanoparticles was investigated for a wide range of process parameters such as ball-milling time and ball-to-powder ratio. The effect of process parameters on the physical and electrochemical properties of the LiFePO₄/C composite was then discussed through the results of X-ray diffraction (XRD) analysis, field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), the Brunauer-Emmet-Teller (BET) method and the use of an electrochemical cell of Li|1 M LiClO₄ in EC:DEC = 1:1|LiFePO₄. The carbon-coated LiFePO₄ nanoparticles were prepared at 500 °C by SP and then milled at a rotating speed of 800 rpm, a ball-to-powder ratio of 40/0.5 and a ball-milling time of 3 h in an Ar atmosphere followed by heat treatment at 600 °C for 4 h in a N₂ + 3% H₂ atmosphere. SEM observation revealed that the particle size of LiFePO₄ was significantly affected by the process parameters. Furthermore, TEM observation revealed that the LiFePO₄ nanoparticles with a geometric mean diameter of 146 nm were coated with a thin carbon layer of several nanometers by the present method. Electrochemical measurement demonstrated that cells containing carbon-coated LiFePO₄ nanoparticles could deliver markedly improved battery performance in terms of discharge capacity, cycling stability and rate capability. The cells exhibited first discharge capacities of 165 mAh g⁻¹ at 0.1 C, 130 mAh g⁻¹ at 5 C, 105 mAh g⁻¹ at 20 C and 75 mAh g⁻¹ at 60 C with no capacity fading after 100 cycles.     

LiFePO4 with enhanced performance synthesized by a novel synthetic route

Pure LiFePO₄ was synthesized by heating an amorphous LiFePO₄. The amorphous LiFePO₄ obtained through lithiation of FePO₄·xH₂O by using oxalic acid as a novel reducing agent at room temperature. FePO₄·xH₂O was prepared through co-precipitation by employing FeSO₄·7H₂O and H₃PO₄ as raw materials. X-ray diffraction (XRD), scanning electron microscopy (SEM) observations showed that LiFePO₄ composites with fine particle sizes between 100 nm and 200 nm, and with homogenous sizes distribution. The electrochemical performance of LiFePO₄ powder synthesized at 500 °C were evaluated using coin cells by galvanostatic charge/discharge. The synthesized LiFePO₄ composites showed a high electrochemical capacity of 166 mAh g⁻¹ at the 0.1C rate, and possessed a favorable capacity cycling maintenance at the 0.1C, 0.2C, 0.5C and 1C rate.     

Electrochemical properties of LiFePO4 prepared via ball-milling

LiFePO₄ cathode materials with distinct particle sizes were prepared by a planetary ball-milling method. The effects of particle size on the morphology, thermal stability and electrochemical performance of LiFePO₄ cathode materials were investigated. The ball-milling method decreased particle size, thereby reducing the length of diffusion and improving the reversibility of the lithium ion intercalation/deintercalation. It is worth noting that the small particle sample prepared using malonic acid as a carbon source achieved a high capacity of 161 mAh g⁻¹ at a 0.1 C rate and had a very flat capacity curve during the early 50 cycles. However, the big particle samples (∼400 nm) decayed more dramatically in capacity than the small particle size samples (∼200 nm) at high current densities. The improvement in electrode performance was mainly due to the fine particles, the small size distribution, and the increase in electronic conductivity as a result of carbon coating. The structure and morphology of the ground LiFePO₄ samples were characterized with XRD, FE-SEM, TEM, EDS, and DSC techniques.     

Effects of Fe2P and Li3PO4 additives on the cycling performance of LiFePO4/C composite cathode materials

In this study, a solution method was employed to synthesize LiFePO₄-based powders with Li₃PO₄ and Fe₂P additives. The composition, crystalline structure, and morphology of the synthesized powders were investigated by using ICP-OES, XRD, TEM, and SEM, respectively. The electrochemical properties of the powders were investigated with cyclic voltammetric and capacity retention studies. The capacity retention studies were carried out with LiFePO₄/Li cells and LiFePO₄/MCMB cells comprised LiFePO₄-based materials prepared at various temperatures from a stoichiometric precursor. Among all of the synthesized powders, the samples synthesized at 750 and 775 °C demonstrate the most promising cycling performance with C/10, C/5, C/2, and 1C rates. The sample synthesized at 775 °C shows initial discharge capacity of 155 mAh g⁻¹ at 30 °C with C/10 rate. From the results of the cycling performance of LiFePO₄/MCMB cells, it is found that 800 °C sample exhibited higher polarization growth rate than 700 °C sample, though it shows lower capacity fading rate than 700 °C sample. For Fe₂P containing samples, the diffusion coefficient of Li⁺ ion increases with increasing amount of Fe₂P, however, the sample synthesized at 900 °C shows much lower Li⁺ ion diffusion coefficient due to the hindrance of Fe₂P layer on the surface of LiFePO₄ particles.     

New freeze-drying method for LiFePO4 synthesis

The freeze-drying method is proposed as an effective synthesis process for the obtaining of LiFePO₄/C composites. The citric acid is used as a complexing agent and carbon source. After the low temperature annealing, the freeze-dried solution leads to a homogeneous carbon covered LiFePO₄ sample. The chemical characterization of the material included ICP and elemental analysis, infrared spectroscopy, X-ray diffraction, magnetic measurements and thermal analysis. SEM and TEM microscopies indicate an aggregate morphology with tiny particles of lithium iron phosphate inside a carbon matrix. Impedance spectroscopy showed a 8.0 × 10⁻⁷ S cm⁻¹ conductivity value. Cyclic voltammetry graphics displayed the two peaks corresponding to the Fe(II)/Fe(III) reaction and demonstrated the good reversibility of the material. The specific capacity value obtained at C/40 rate was 164 mAh g⁻¹, with a slight decrease on greater C-rates reaching 146 mAh g⁻¹ at C/1. The capacity retention study has evidenced good properties, with retention over 97% of the maximum values in the first 50 cycles, which allows an effective performance of the freeze-dried sample as cathodic material in lithium-ion batteries.     

Formation mechanism of LiFePO4/C composite powders investigated by X-ray absorption spectroscopy

The local structure and oxidation states for both the precursors and the LiFePO₄/C composite powders were investigated by X-ray absorption spectroscopy (XAS) to provide a deep insight into their formation mechanism. It was found that the local structure and oxidation states of the precursors and the synthesized LiFePO₄/C powders as well as the electrochemical properties of the synthesized powders were strongly influenced by the R ratio (R: molar ratio of citric acid to total metal ions). The oxidation states of iron ions of the precursors for R = 1 and 0.75 consist mainly of Fe(II) and traces of Fe(III). However, the oxidation state of iron ions of the precursor for R = 0.5 comprises mainly of Fe(III). The oxidation state of iron ions of all the synthesized powders is Fe(II). The structure of the precursors and the synthesized powders for R = 1 and 0.75 is more ordering than that for R = 0.5. It is in good agreement with the observation of the cation mixing obtained from the Riteveld analysis of the XRD data. The better the electrochemical performance is, the more ordering the structure or the less the cation mixing. However, the effect of the R values on the carbon content is also essential for the electrochemical properties of the synthesized LiFePO₄/C composite powders. Increasing the carbon content leads to the increase in the electronic conductivity but impedes the Li⁺ ion diffusion of the composite materials. Consequently, the powders synthesized at the optimal R ratio of 0.75 exhibited the highest initial capacity, about 150 mAh g⁻¹ when cycled at 1/40 C rate at room temperature. The structural scheme of the precursors and the synthesized powders and the formation mechanism of the LiFePO₄/C composite powders are also addressed in this work.     

A study on the electrochemical characteristics of LiFePO4 cathode for lithium polymer batteries by hydrothermal method

Phospho-olivine LiFePO₄ cathode materials were prepared by hydrothermal reaction at 150 °C. Carbon black was added to enhance the electrical conductivity of LiFePO₄. LiFePO₄-C powders (0, 3, 5 and 10 wt.%) were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM). LiFePO₄-C/solid polymer electrolyte (SPE)/Li cells were characterized electrochemically by charge/discharge experiments at a constant current density of 0.1 mA cm⁻² in a range between 2.5 and 4.3 V vs. Li/Li⁺, cyclic voltammetry (CV) and ac impedance spectroscopy. The results showed that initial discharge capacity of LiFePO₄ was 104 mAh g⁻¹. The discharge capacity of LiFePO₄-C/SPE/Li cell with 5 wt.% carbon black was 128 mAh g⁻¹ at the first cycle and 127 mAh g⁻¹ after 30 cycles, respectively. It was demonstrated that cycling performance of LiFePO₄-C/SPE/Li cells was better than that of LiFePO₄/SPE/Li cells.     

Synthesis and characterization of Carbon Nano Fiber/LiFePO4 composites for Li-ion batteries

Carbon Nano Fibers (CNFs) coated with LiFePO₄ particles have been prepared by a non-aqueous sol–gel technique. The functionalization of the CNFs by HNO₃ acid treatment has been confirmed by Raman and XPS analyses. The samples pure LiFePO₄ and LiFePO₄–CNF have been characterized by XRD, SEM, RAMAN, XPS and electrochemical analysis. The LiFePO₄–CNF sample shows better electrochemical performance compared to as-prepared LiFePO₄. LiFePO₄–CNF (10 wt.%) delivers a higher specific capacity (∼140 mAh g⁻¹) than LiFePO₄ with carbon black (25 wt.%) added after synthesis (∼120 mAh g⁻¹) at 0.1C.     

Hydrothermal preparation of LiFePO4 nanocrystals mediated by organic acid

Well-crystallized LiFePO₄ nanoparticles have been directly synthesized in a short time via hydrothermal process in the presence of organic acid, e.g. citric acid or ascorbic acid. These acid-mediated LiFePO₄ products exhibit a phase-pure and nanocrystal nature with size about 50-100 nm. Two critical roles that the organic acid mediator plays in hydrothermal process are recognized and a rational mechanism is explored. After a post carbon-coating treatment at 600 °C for 1 h, these mediated LiFePO₄ materials show a high electrochemical activity in terms of reversible capacity, cycling stability and rate capability. Particularly, LiFePO₄ mediated by ascorbic acid can deliver a capacity of 162 mAh g⁻¹ at 0.1 C, 154 mAh g⁻¹ at 1 C, and 122 mAh g⁻¹ at 5 C. The crystalline structure, particle morphology, and surface microstructure were characterized by high-energy synchrotron X-ray diffraction (XRD), transmission electron microscopy (TEM) and scanning electron microscopy (SEM), and Raman spectroscopy, respectively. And the electrochemical properties were thoroughly investigated by galvanostatic test and electrochemical impedance spectroscopy (EIS).     

Physical and electrochemical properties of LiFePO4/C composite cathode prepared from various polymer-containing precursors

The goal of this research was to study the effect of various polymer-containing precursors on the performance of LiFePO₄/C composite. A coprecipitation method was applied to prepare a series of LiFePO₄/C materials by calcinating amorphous LiFePO₄ with various polymer compounds at 600 °C. The materials were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, particle size analysis, thermal analysis, BET specific surface area, Raman spectral analysis and electrochemical methods. The results showed that the structure of polymer precursors played an important role in improving the performance of LiFePO₄/C composites. The residual carbon produced by the pyrolysis of polymers with functionalized aromatic groups exhibited a better capacity in the LiFePO₄/C composites. A polyaromatic compound, e.g. polystyrene, with more functionalized aromatic groups displayed improved performance because its decomposition temperature was close to the temperature of the LiFePO₄ phase transformation, which resulted in fine particle size and uniform carbon distribution on the composite surface. According to Raman spectral analysis, polystyrene with more aromatic groups has a lower I_D/I_G and sp³/sp² peak ratio indicating more highly graphite-like carbon formation during polymer pyrolysis and exhibited a better capacity.     

Directed growth of nanoarchitectured LiFePO4 electrode by solvothermal synthesis and their cathode properties

We demonstrate a rapid and one-pot solvothermal synthesis of LiFePO₄ hierarchical nanorods and flowers like microstructures in a short reaction time (4-10 min) at temperature as low as 300-400 °C, without any high temperature post-annealing. The ethylene glycol was used as a solvent with hexane and oleic acid as co-solvent and surfactant, respectively. Addition of the co-solvent and/or surfactant played a key role in controlling the morphology and microstructures of the LiFePO₄ nanocrystals. The EG and oleic acid were acted as the size and morphology controlling agents and carbon source when annealed at 600 °C. Sample exhibited about 90% specific capacity at 0.5 °C and showed good cyclic performance. The high-resolution TEM image revealed that these nanorods were self-assembled to form flower like microstructure in presence of oleic acid during the synthesis.     

Electrochemical properties of LiFePO4 prepared via hydrothermal route

LiFePO₄ as a cathode material for rechargeable lithium batteries was prepared by hydrothermal process at 170 °C under inert atmosphere. The starting materials were LiOH, FeSO₄, and (NH₄)₂HPO₄. The particle size of the obtained LiFePO₄ was 0.5 μm. The electrochemical properties of LiFePO₄ were characterized in a mixed solvent of ethylene carbonate and diethyl carbonate (1:1 in volume) containing 1.0 mol dm⁻³ LiClO₄. The hydrothermally synthesized LiFePO₄ exhibited a discharge capacity of 130 mA h g⁻¹, which was smaller than theoretical capacity (170 mA h g⁻¹). The annealing of LiFePO₄ at 400 °C in argon atmosphere was effective in increasing the discharge capacity. The discharge capacity of the annealed LiFePO₄ was 150 mA h g⁻¹.     

Synthesises,characterizations and electrochemical properties of spherical-like LiFePO4 by hydrothermal method

Spherical-like LiFePO₄ was synthesized by hydrothermal synthesis method using Phenanthroline as a complexing-agent to avoid the Fe(II) ions from oxidation and control the growth of the crystal. Structural, electron valence state, morphology and particle size were investigated by X-ray diffraction (XRD), X-ray photoelectron spectra (XPS), Mössbauer spectra, scanning electron microscopy (SEM) and laser particle sizer. Charge–discharge cycling performances were used to characterize its electrochemical properties. The sample possesses uniformly distributed spherical-like particles with an average size of 0.5–1 μm. Test shows that the reversible capacity of spherical-like LiFePO₄ is about 140 mAh g⁻¹ at 0.1 C. The capacity fading is neglectable.