Fabrication of SiC_p/AA5083 composite via friction stir welding

Microstructure and mechanical properties of SiCp /AA5083 composite fabricated by friction stir welding (FSW) were investigated.The influence of the number of FSW passes on the distribution of SiC particles and mechanical properties in the joint was studied.After one pass,the SiC particles were entangled in the upper side of the stir zone (SZ).However,the particle distribution became more uniform after two passes due to the repeated stirring of the joint.As the SiC particles facilitate the grain refinement in the SZ by the pinning effect,the particle including region has much smaller grain size than the SZ without SiC particles.The SiCp /AA5083 composite region exhibits a Vickers hardness of HV90,which is much higher than the value of HV80 in the SZ produced by FSW without SiC particles.     

AA6061-T6与AZ31合金异种搅拌摩擦焊接头的微观组织

研究了AA6061-T6和AZ31合金异种搅拌摩擦焊接头的微观组织。在异种搅拌摩擦焊接AA6061-T6与AZ31合金时,采用偏置条件,即将搅拌针插入时偏向AZ31合金,从而得到异种对接接头。通过预备实验来优化搅拌针的前进速度、旋转速度。运用电子背散射衍射技术观察搅拌区的纹理,并得到粒径分布和错位角分布,在搅拌区存在相对精细的晶粒结构。在AA6061-T6搅拌区出现随机或弱面取向,而在AZ31搅拌区出现旋转底面取向。再结晶颗粒的平均尺寸只有2．5～4．5μm。与基础合金相比,在AA6061-T6搅拌区的大角度晶界的分数增大,而在AZ31搅拌区的小角度晶界的分数降低。     

Electrochemical study of the surface metal matrix composite developed on AA 2024-T351 by the friction stir process

ABSTRACT

This work is focused on the evaluation of the corrosion behaviour of an AA2024-T351/SiC surface composite produced by friction stir processing (FSP). The surfaces composite show a quite homogenous distribution of the SiC particles in the stir zone, together with a significant grain size reduction as Electron Backscatter Diffraction analysis confirms. The corrosion behaviour was evaluated in 3.5 wt-% NaCl solution using electrochemical techniques. The complete study shows that all processed samples have similar corrosion resistance at the stirred region and differ from the base material behaviour. The results indicate that the galvanic coupling metal matrix–SiC particles are less active than the galvanic coupling metal matrix–Cu-rich second phases. Although the initial corrosion resistance of the base aluminium alloy is the worst of all systems studied, for long immersion times the development of corrosion through grain boundaries was found to progressdeeper in the 2024Al/SiC surface produced by FSP.     

异种搅拌摩擦焊制备铜铝合金双金属纳米复合材料

对纯铜与AA5754合金进行对接搅拌摩擦焊接.为了降低金属间化合物的有害影响,在搅拌摩擦焊(FSW)接头中添加纳米SiC强化颗粒.采用拉伸试验、显微硬度试验、扫描电镜和X射线衍射分析方法研究焊接接头的性能.结果显示,当焊接速度为50 mm/min、转速为1000 r/min时接头的性能最好.纳米SiC颗粒的存在使搅拌区...     

搅拌摩擦加工制备A356铝基复合材料的显微组织与力学性能(英文)

通过搅拌摩擦加工技术将SiC颗粒加入到A356铝合金中制备铝基复合材料,搅拌摩擦加工参数为:旋转速度1800r/min和行进速度127mm/min。基体金属A356铝合金为亚共晶AlSi枝晶组织,而搅拌区的组织与基体金属区不同。共晶Si和SiC颗粒均匀分布于初始铝固溶体中,而经历了剧烈变形的热力影响区的共晶Si和SiC颗粒呈沿旋转方向分散的特征。搅拌区的硬度比基体金属的高,因为在搅拌区存在的缺陷明显减少,共晶Si和SiC均匀分布在其中。     

Influence of addition of Grp/Al2O3p with SiCp on wear properties of aluminum alloy 6061-T6 hybrid composites via friction stir processing

Aluminum alloy base surface hybrid composites were fabricated by incorporating with mixture of (SiC+Gr) and (SiC+Al₂O₃) particles of 20 μm in average size on an aluminum alloy 6061-T6 plate using friction stir processing (FSP). Microstructures of both the surface hybrid composites revealed that SiC, Gr and Al₂O₃are uniformly dispersed in the nugget zone (NZ). It was observed that the addition of Gr particles rather than Al₂O₃ particles with SiC particles, decreases the microhardness but immensely increases the dry sliding wear resistance of aluminum alloy 6061-T6 surface hybrid composite. The observed microhardness and wear properties are correlated with microstructures and worn micrographs.     

Effect of Heat Input on Mechanical and Metallurgical Properties of Friction Stir Welded AA6061-10% SiCp MMCs

Metal matrix composites (MMCs) reinforced with SiC particles combine the matrix properties with those of the ceramic reinforcement, leading to higher stiffness and superior thermal stability with respect to the corresponding unreinforced alloys. However, their wide application as structural material needs proper development of a suitable joining process. In this investigation, an attempt was made to study the effect of heat input on the evolution of microstructure in weld region of friction stir welded AA6061-10% SiCp MMCs. The tensile properties of the joints were evaluated and they are related with microstructure and heat input of the process. The microstructure characterization of the weld zone shows evidence of a substantial grain refinement of the aluminum matrix and fracturing of reinforcement particles due to dynamic recrystallization induced by the plastic deformation and frictional heating during welding.     

Establishing empirical relationships to predict grain size and tensile strength of friction stir welded AA 6061-T6 aluminium alloy joints

AA 6061-T6 aluminium alloy(Al-Mg-Si alloy) has gathered wide acceptance in the fabrication of light weight structures requiring a high specific strength and good corrosion resistance.Compared with the fusion welding processes that are routinely used for joining structural aluminium alloys,friction stir welding(FSW) process is an emerging solid state joining process in which the material welded does not melt and recast.Joint strength is influenced by the grain size and tensile strength of the weld nugget region.Hence,an attempt was made to develop empirical relationships to predict grain size and tensile strength of friction stir welded AA 6061-T6 aluminium alloy joints.The empirical relationships are developed by response surface methodology(RSM) incorporating FSW tool and process parameters.A linear regression relationship was also established between grain size and tensile strength of the weld nugget of FSW joints.     

Rupture locations of friction stir welded joints of AA2017-T351 and AA6061-T6 aluminum alloys

The tensile rupture locations of friction stir welded joints of AA2017-T351 and AA6061-T6 aluminum alloys were examined. The experiments show that the rupture locations of the joints are different for the two aluminum alloys, which are influenced by the welding parameters. When the joints are free of welding defects, the AA2017-T351 joints are ruptured in the weld nugget adjacent to the thermo-mechanically affected zone on the advancing side and the rupture surfaces appear as oval contours of the weld nugget, while the AA6061-T6 joints are ruptured in the heat affected zone on the retreating side and the rupture surfaces are inclined at a certain degree to the bottom surfaces of the joints. When welding defects are present in the joints, the AA2017-T351 joints are ruptured in the weld center, while the AA6061-T6 joints are ruptured on the retreating side near the weld center. The rupture locations of the joints are dependent on the internal structures of the joints and can be explained through them.     

Effect of post-weld heat treatment on joint properties of dissimilar friction stir welded 2024-T4 and 7075-T6 aluminum alloys

The effect of post-weld heat treatment on dissimilar friction stir welded AA7075 and AA2024 joints was studied. After welding in constant parameters, solution heat treatment and various aging treatments were given to the welded joints. Microstructural and phase characterizations were done using optical microscope, SEM, FE-SEM, XRD and EDS techniques. Finally, mechanical properties of post-weld heat treated joints were evaluated and compared with as-welded joints. Results show that both 2024-T6 and 7075-T6 post-weld heat treatment procedures considerably improve the mechanical strength of the welded joint, with higher strength obtained for the 7075-T6 procedure, in comparison with the as-welded joint. This is explained by the formation of fine precipitates during the aging process, despite the abnormal grain growth. Fracture occurs at the interface between thermo-mechanical affected zone (TMAZ) and heat affected zone (HAZ) on the retreating side (AA7075) of as-welded joint, while by applying post-weld heat treatment fracture location shifts towards the stir zone (SZ) of the welded joint. Also, for post-weld heat treated samples, fracture surface is predominantly inter-granular, while in as-weld joint, fracture surface is mostly trans-granular. This is explained by dissolution and coarsening of precipitates within grains in post-weld heat treated joints.     

Wear Performance of A356 Matrix Composites Reinforced with Different Types of Reinforcing Particles

To improve the wear resistance of Al-Si alloys, different types of reinforcing particles such as SiC, TiC, ZrO₂, and B₄C were used to produce matrix composites by friction stir processing (FSP). First, microstructural properties of different locations of stir zone (SZ) in the FSPed specimens such as advancing side, retreating side, shoulder-affected area, and pin-affected area were investigated. The results demonstrate that Si particles size is not the same in different SZ subdomains. SEM investigation was performed in order to investigate the particles distribution in different areas of the SZ as well as bonding quality between particles and metal matrix. Hardness and wear tests were carried out to determine mechanical and wear properties of the composites. The pin-on-disk wear tests were performed at room temperature, with the normal applied loads of 5, 10, and 20 N and sliding speed of 1 and 2 m/s. All fabricated composites show higher resistance in wear than A356 alloy. Wear test results show, by increasing the normal load and sliding velocity, the wear loss weight of all composites increased gradually.     

A comparative study on microstructural evolution and surface properties of graphene/CNT reinforced Al6061−SiC hybrid surface composite fabricated via friction stir processing

A comparative study on the surface properties of Al−SiC−multi walled carbon nanotubes (CNT) and Al−SiC−graphene nanoplatelets (GNP) hybrid composites fabricated via friction stir processing (FSP) was documented. Microstructural characterization reveals a more homogeneous dispersion of GNPs in the Al matrix as compared to CNTs. Dislocation blockade by SiC and GNP particles along with the defect-free interface between the matrix and reinforcements is also observed. Nanoindentation study reveals a remarkable ∼207% and ∼27% increment in surface nano-hardness of Al−SiC−GNP and Al−SiC−CNT hybrid composite compared to as-received Al6061 alloy, respectively. On the other hand, the microhardness values of Al−SiC−GNP and Al−SiC−CNT are increased by ∼36% and ∼17% relative to as-received Al6061 alloy, respectively. Tribological assessment reveals ∼56% decrease in the specific wear rate of Al−SiC−GNP hybrid composite, whereas it is increased by ∼122% in Al−SiC−CNT composite. The higher strength of Al−SiC−GNP composite is attributed to the mechanical exfoliation of GNPs to few layered graphene (FLG) in the presence of SiC. Also, various mechanisms such as thermal mismatch, grain refinement, and Orowan looping contribute significantly towards the strengthening of composites. Moreover, the formation of tribolayer by the squeezed-out GNP on the surface is responsible for the improved tribological performance of the composites. Raman spectroscopy and various other characterization methods corroborate the results.     

Friction Stir-Welded Dissimilar Aluminum Alloys: Microstructure, Mechanical Properties, and Physical State

A356 and 6061 aluminum alloys were joined by friction stir welding at constant tool rotational rate with different tool-traversing speeds. Thermomechanical data of welding showed that increment in tool speed reduced the pseudo heat index and temperature at weld nugget (WN). On the other hand, volume of material within extrusion zone, strain rate, and Zenner Hollomon parameter were reduced with decrease in tool speed. Optical microstructure of WN exhibited nearly uniform dispersion of Si-rich particles, fine grain size of 6061 Al alloy, and disappearance of second phase within 6061 Al alloy. With enhancement in welding speed, matrix grain size became finer, yet size of Si-rich particles did not reduce incessantly. Size of Si-rich particles was governed by interaction time between tool and substrate. Mechanical property of WN was evaluated. It has been found that the maximum joint efficiency of 116% with respect to that of 6061 alloy was obtained at an intermediate tool-traversing speed, where matrix grain size was significantly fine and those of Si-rich particles were substantially small.     

Evolution of Quasicrystals and Long-Period Stacking Ordered Structures During Severe Plastic Deformation and Mixing of Dissimilar Mg Alloys Upon Friction Stir Welding

Microstructural evolution during severe plastic deformation and mixing of Mg_(95.8)Zn_(3.6)Gd_(0.6) and Mg_(97)Cu_1Y_2(at%) alloys upon friction stir welding was studied.A laminated onion-ring structure composed of alternative distribution of layers with significantly refined microstructures from diff erent alloys was formed in the stirred zone.Coarse quasicrystals were broken up and dispersed with most of them being transformed into cubic W-phase particles,and thick 18 R long-period stacking ordered plates were fractured and transformed into fine 14 H-LPSO lamellae in the stirred zone(SZ) experiencing complex material flow under high strain rate.Fine W-phase particles and 14 H-LPSO lamellae formed during dissimilar friction stir welding(FSW) usually have no specific orientation relationship with surrounding Mg matrix.Chemical measurements demonstrated occurrence of interdiff usion between dissimilar layers in the SZ.Phase transformation was observed for some particles of quasicrystals and long-period stacking ordered(LPSO) in regions slightly outside the SZ.An ultimate tensile strength of ～ 415 MPa and an elongation to failure of ～ 27.8%,both exceeding those of base materials,were obtained in the SZ,due to microstructural refinement and formation of a laminated structure.     

Improvement of Structural and Mechanical Properties of Al-1100 Alloy via Friction Stir Processing

In the present study, the relationship between structural and mechanical properties of friction stir processed Al-1100 alloy and process parameters (tool rotation rate: ω and traverse speed: ν) was studied to get an better understanding and optimizing the friction stir processing (FSP) condition of this alloy. Microstructural studies revealed that increasing of ω up to 720 rpm resulted in grain refinement in the stirred zone (SZ), but higher increasing of ω caused grain growth in this zone. These variations of SZ grain size illustrated that the prevailing factor that determined the SZ grain size was plastic deformation at first and thereafter, peak temperature in the SZ. Mechanical properties investigations were in accordance with microstructural findings and illustrated that optimized FSP condition for Al-1100 alloy was 720 rpm and 20 mm/min. Optimized FSP condition resulted in a significant improvement of tensile strength and elongation up to 22 and 8% of those of base metal, respectively.     

Microstructure and mechanical properties of friction stir weld of dissimilar AZ31-O magnesium alloy to 6061-T6 aluminum alloy

Dissimilar friction stir welding between AZ31-O Mg and 6061-T6 Al alloys was investigated. 3 mm thick plates of aluminum and magnesium were used. Friction stir welding operations were performed at different rotation and travel speeds. The rotation speeds varied from 600 to 1400 r/min, and the travel speed varied from 20 to 60 mm/min. Defect-free weld was obtained with a rotation speed of 1000 r/min and travel speed of 40 mm/min. Metallographic studies showed that the grain size in the stir zone is much finer than that in the base metals. Complex flow pattern was formed in the stir zone. Microhardness measurement revealed an uneven distribution in the stir zone. Tensile test results indicated that the tensile strength of the welded specimen is about 76% of AZ31 Mg alloy and 60% of the 6061 Al alloy in tensile strength. SEM fracture surface image of the welded specimen indicated that the welded specimen failed through brittle-mode fracture.     

Electrochemical corrosion behaviour of stir zone of friction stir welded dissimilar joints of AA6061 aluminium–AZ31B magnesium alloys

Joining of dissimilar metals will offer many advantages in transportation sectors such as fuel consumption, weight reduction and emission reduction. However, joining of aluminium (Al) alloys with magnesium (Mg) alloys by fusion welding process is very complicated. Friction stir welding (FSW) is a feasible method to join these two dissimilar alloys. Mixing these two metals together in stir zone (SZ) leads to poor corrosion resistance. In this investigation, an attempt has been made to understand the corrosion resistance of SZ of FSWed dissimilar joints of AA6061 Al alloy and AZ31B Mg alloy. Potentiodynamic polarization test was conducted by varying chloride ion concentration, pH value of the NaCl solution and exposure time. The corroded surfaces were analyzed using optical microscopy, scanning electron microscopy and XRD techniques. Of these three factors investigated, exposure time is found to be the most significant factor to influence the corrosion behaviour of SZ of friction stir welded dissimilar joints of Al/Mg alloys.     

Effects of use of higher strength interlayer and external cooling on properties of friction stir welded AA6061-T6 joints

Although sound AA6061-T6 joints can be produced by friction stir welding, a loss in strength takes place in the weld region. In this study, it was demonstrated that the strength of the nugget could be increased by the use of a higher strength interlayer during friction stir welding. This strength recovery cannot, however, be attainable in the heat affected zone. Although an external cooling was applied during welding in order to increase strength in the heat affected zone, it was not sufficient for achieving the required cooling condition for improved strength.     

C18000铜合金搅拌摩擦焊接头微观组织与性能

对3.5 mm厚的C18000铜合金板进行搅拌摩擦焊焊接试验. 在焊接速度120 mm/min,转速1 200 r/min工艺下获得无缺陷焊接接头. 在金相显微镜下对接头的宏观形貌、微观组织进行观察,用扫描电镜和透射电镜对母材和搅拌区组织进行观察分析. 结果表明,接头区大致分为母材区、热影响区、热力影响区和搅拌区,搅拌区晶粒细小均匀,热力影响区晶粒沿边界切线方向被拉长;搅拌区Cr₃Si相部分溶解,搅拌区组织中的Cr单质相和Ni₂Si相溶解导致接头硬度和抗拉强度下降. 搅拌区平均硬度为151.4 HV;接头抗拉强度为497 MPa,达到母材的72%;接头电导率下降为35%IACS.     

转速对6061-T6铝合金搅拌摩擦搭接焊接头力学性能的影响(英文)

采用场发射扫描电子显微镜(FE-SEM),研究转速对厚度为5 mm的6061-T6铝合金搅拌摩擦搭接焊接头的宏观和微观组织、硬度、搭接头剪切性能和失效模式的影响。结果表明:在最低的转速度下,上模板和下模板具有十分相似的硬度分布。采用EDX分析发现,焊核区的断裂面中含有Fe的化合物。