Investigation on the crystallization behavior of poly(ether ether ketone)/poly(phenylene sulfide) blends

The morphology of nonisothermally crystallized poly(phenylene sulfide) (PPS) and its blend with poly (ether ether ketone) (PEEK) have been observed by polarized optical microscope (POM) equipped with a hot stage. The nonisothermal crystallization behavior of PPS and PEEK/PPS blend has also been investigated by differential scanning calorimetry (DSC). The maximum crystallization temperature for PEEK/PPS blend is about 15°C higher than that of neat PPS, and the crystallization rate, characterized by half crystallization time, of the PEEK/PPS blend is also higher than that of the neat PPS. These results indicate that the PEEK acts as an effective nucleation agent and greatly accelerates the crystallization rate of PPS. The Ozawa model was used to analyze the nonisothermal crystallization kinetics of PPS and its blends. The Avrami exponent values of neat PPS are higher than that of its blend, which shows that the presence of PEEK changed the nucleation type of PPS from homogeneous nucleation to heterogeneous nucleation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Improvement of interfacial interactions in CF/PEEK composites by an s-PSF/graphene oxide compound sizing agent

The interfacial interactions of carbon fiber (CF)-reinforced polymer composites is a key factor affecting the overall performance of the material. In this work, we prepared a sulfonated poly(ether sulfone)–graphene oxide mixed sizing agent to modify the interface of CF/PEEK composites and improve the interfacial properties between the PEEK matrix and CF. Results showed that the mechanical and interfacial properties of CF/PEEK composites are improved by the sizing agent. Specifically, the flexural strength, flexural modulus and interlaminar shear strength of the materials reached 847.29 MPa, 63.77 GPa, and 73.17 MPa, respectively. Scanning electron microscopy confirmed markedly improved adhesion between the resin matrix and fibers. This work provides a simple and effective method for the preparation of high-performance CF/PEEK composites, which can improve the performance of composites without degrading the mechanical property of pristine CF.     

Effect of physical aging on the toughness of carbon fiber-reinforced poly(ether ether ketone) and poly(phenylene sulfide) composites. I

The effect of physical aging on the penetration impact toughness and Mode I interlaminar fracture toughness of continuous carbon fiber (C.F.) reinforced poly(ether ether ketone) (PEEK) and poly(phenylene sulfide) (PPS) composites has been investigated by using an instrumented falling weight impact (IFWI) technique and a double cantilever beam (DCB) test. Composite materials studied are aged below their glass transition temperature (T_g) at various periods. Initiation force and energy of damage, failure propagation energy, impact energy and ductility index (D.I.) are reported. The Mode I critical value of strain energy release rate (G_IC) of the unidirectional carbon fiber-reinforced PEEK (APC-2) composites is obtained. Results show that aging has a significant effect on the toughness of both composite materials. Energy absorbed during impact decreases with the increase of aging temperature and period. The PEEK/C.F. composites exhibit a higher retention of impact toughness than that of the PPS/C.F. composites after aging; however, the PPS/C.F. composites show a much higher ductility index. The Mode I fracture mechanism of the APC-2 composite is a combination of stable and unstable failure and shows a “stick-slip” behavior. Owing to the formation of a relative rigid structure, the fracture toughness (G_IC) of APC-2 decreased with the increase of aging temperature and period.     

聚四氟乙烯填充聚醚醚酮及其复合材料的研究

利用熔融共混工艺制备了ＰＥＥＫ／ＰＴＦＥ共混物及其复合材料,研究了ＰＴＦＥ对ＰＥＥＫ共混物及其复合材料力学性能和耐磨性的影响,结果表明,ＰＥＥＫ经１０％￣ＰＴＦＥ填充改性,玻纤／碳纤混杂增强后,由于磨损方式的改变,使该复合材料不仅保持了良好的物理力学性能,而且具有较低的摩擦系数,耐磨性也得到明显改善。     

Poly(ether ether ketone)/wrapped graphite nanosheets with poly(ether sulfone) composites: Preparation,mechanical properties,and tribological behavior

Antiwear composites with extraordinary tribological performances and good mechanical/thermal properties were developed by the dispersion of poly(ether sulfone) (PES) wrapped graphite nanosheets (GNSs) inside a poly(ether ether ketone) (PEEK) matrix via melt blending. The tribological behaviors and the mechanical/thermal properties of the composites were carefully investigated. Compared with pure PEEK and PEEK/GNS composites, the PEEK/wrapped GNS composites exhibited considerable enhancements in those performances; these were attributed to the eliminated layer of PES; this elimination not only eliminated the GNS aggregation inside the PEEK matrix for homogeneous distribution inside the PEEK matrix but also enhanced the interfacial adhesion between the PEEK and wrapped GNSs. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41728.     

Thermal Aging Properties of Graphite Fiber Reinforced Peek and Graphite Fiber Reinforced Bmi Composites

Graphite fiber reinforced poly(ether ether ketone) (PEEK) and graphite fiber reinforced bismaleimide (BMI) composite materials are two kinds of advanced fiber-reinforced polymer matrix composites with good thermal stability and excellent mechanical properties at high temperature. They are currently receiving considerable attention. the main limitation on their application is the lack of knowledge regarding their behaviors during extended use at high temperature. Thermal aging properties are the main parameters for new polymer matrix composites that will be used in advanced spacecraft structural components. From the results of thermal aging effects on the properties—including interlaminar shear strength, drop-weight impact strength, and impact energy—of graphite/PEEK and graphite/BMI composites, it is found that unidirectional graphite fiber reinforced composites retain higher strength compared to multidirectional, and that multidirectional graphite/PEEK composites keep higher property retentions than multidirectional graphite/BMI composites after thermal aging at 190°C. From scanning electron photomicrographs, it is also found that graphite/PEEK composites have better fiber/resin adhesion, intraply adhesion, and microcrack resistance compared to graphite/BMI composites after thermal aging.     

Improved interfacial adhesion in carbon fiber/poly (ether ether ketone) composites with the sulfonated poly (ether ether ketone) sizing treatment

A water-soluble sulfonated poly (ether ether ketone) (SPEEK) sizing agent is prepared and applied to improve the interfacial adhesion of carbon fiber/poly (ether ether ketone) (CF/PEEK) composites. The surface morphology, surface roughness, surface chemistries, and surface free energy of SPEEK sized CF are obtained to understand the sizing effect. The results reveal the increased surface free energy and surface roughness of SPEEK sized CF. In addition, a chemical reaction between the CF surface and sizing layer is proved based on the results of XPS, IR, and ¹H NMR. The interfacial structure of CF/PEEK composites is further ascertained by AFM and the appearance of gradient interface could be verified for SPEEK sized CF/PEEK composites. The formation of the gradient interface is due to the chemical reaction between the CF and sizing agent as well as the improved compatibility between the sized CF and matrix, which benefits the improvement of interfacial adhesion.     

Isothermal crystallization and melting behavior of short carbon fiber reinforced poly(ether ether ketone) composites

Films of short carbon fiber reinforced poly(ether ether ketone) (PEEK) composite were formed by compression molding pellets for 10 min at 380 °C under air. A heating stage was used to prepare isothermally treated PEEK composites before DSC scan. The dependence of degree of crystallinity on the heating rate (10–80 °C/min) was investigated for specimens crystallized at different temperatures. The results indicated that 50 °C/min was an optimum heating rate to suppress the reorganization and to avoid the superheating of high crystallinity specimens with the sample weight of 10 mg. The upper peak temperature of double-melting peaks continued to increase with crystallization temperature. This peak temperature was related to the transition from regime II to III. The phenomenon of lower crystallinity and higher melting temperature supports the interpretation that the upper melting peak corresponded to crystals growing during the earlier stage of isothermal crystallization.     

Mechanical and Thermal Properties of Poly(phthalazinone biphenyl ether sulfone)/PEEK Blends

A series of blends with various compositions are prepared by melt extrusion on the basis of novel copoly(phthalazinone biphenyl ether sulfone) (PPBES) and poly(ether ether ketone) (PEEK). The melt flowability, mechanical and thermal properties of the blends are studied. The results show that the incorporated PEEK has a large influence on the melt viscosity and thermal stability of blends. The tensile strength of the blends remains at about 90 MPa at room temperature; PPBES improves the mechanical properties of PEEK at 150°C. The flexural strength and modulus of the PPBES/PEEK blends also increase with the addition of PEEK.     

Enhanced mechanical and electrical properties of carbon fiber/poly(ether ether ketone) laminates via inserting carbon nanotubes interleaves

The carbon fiber/(carbon nanotubes/polyetherimide)/poly ether ether ketone (CF/(CNTs/PEI)/PEEK) laminates are prepared by inserting carbon nanotubes/polyetherimide (CNTs/PEI) interleaves into interlaminar region. The mechanical properties and electrical conductivities of the developed laminates are evaluated. The results indicate that the interlaminar shear strength and flexural strength of CF/(CNTs/PEI)/PEEK laminates are increased by 42.9% and 24.7%, after inserting CNTs2.91/PEI interleaves, respectively. The cross-sectional images of laminates after mechanical tests verify strong fiber-resin adhesion by scanning electron microscope observation. The pertinent mechanism responsible for the improvement of mechanical properties is mechanical interlocking effect of CNTs. After incorporating CNTs/PEI interleaves, the electrical conductivity of laminates is markedly improved due to the formation of conductive pathway. This work suggests that this method is compatible with the preparation process of thermoplastic composites. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 137, 48658.     

PPS/recycled PEEK/ carbon nanotube composites: Structure,properties and compatibility

Blends of poly(phenylene sulfide) (PPS) and recycled poly(ether ether ketone) (r‐PEEK) were prepared using a twin‐screw extruder. The carbon nanotube (CNT) added to the blends not only improved the compatibility of the two polymers, but also affected the morphology of the immiscible PPS/r‐PEEK blends. R‐PEEK always forms the dispersed phase and PPS the continuous phase in such blends. In the composite, CNT particles were observed in the PPS phase, mostly distributes in the interface between PPS and PEEK. The results show that r‐PEEK improves the impact and tensile strength of PPS, but does not provide nucleation effect on PPS. However, CNT improved the flexural modulus of PPS/r‐PEEK blends and promoted the crystallization of r‐PEEK rather than that of PPS. The prepared PPS/r‐PEEK blends provided larger electrical conductivity than neat polymers. Adding 20 wt % CNT to blend resulted in composite with the minimum volume resistivity, a reduction of four orders of magnitude, compared with that of the neat blend. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42497.     

Chemical resistance of carbon fiber-reinforced poly(ether ether ketone) and poly(phenylene sulfide) composites

Studies have been conducted to investigate the aircraft fluid and chemical solvent resistance of the carbon fiber-reinforced poly(phenylene sulfide) (PPS) and poly(ether ether ketone) (PEEK) composites. The solvents and aircraft fluids utilized in this work include hydraulic fluid, paint stripper, JP-4 jet fuel, methyl ethyl ketone, and methylene chloride. The weight gain of the composites as a function of time is measured. Tensile and flexural strength, thermal behavior, and dynamic mechanical properties of the composites are examined. The alteration of crystallinity change of the composites is investigated by X-ray diffraction. It is found that paint stripper degraded the mechanical properties of the composites significantly. Furthermore, crystallization enhancement of the low crystallinity composites in the presence of solvents and aircraft fluids is also observed.     

End‐functionalized thermoplastic‐toughened phthalonitrile composites: influence on cure reaction and mechanical and thermal properties

Phthalonitrile polymers are known for their high thermal stability and good mechanical properties. However, their brittle nature limits their application as structural composites in many critical areas. The present study investigates the feasibility of toughening novolac–phthalonitrile (NPN) resin using chemically modified poly(ether ether ketone) (PEEK). A telechelic PEEK bearing a phthalonitrile end group (PEEKPN) was synthesized via nucleophilic substitution of nitrophthalonitrile with the corresponding phenol–telechelic poly(ether ether ketone) (PEEKOH). Different compositions of NPN and PEEKOH–PEEKPN blends with curing agent, i.e. diaminodiphenylsulfone, were investigated for their cure behaviour and mechanical properties of their carbon fabric composites. In NPN–PEEKOH blends, crosslinking of the phthalonitrile groups was facilitated by phenol‐mediated reactions resulting in the reduction of cure temperatures by around 130 °C with substantial improvement in thermal stability. Blending the resin with the thermoplastic enhanced the mechanical properties of the composites. The apparent flexural strength and impact strength of carbon fabric‐reinforced composites were improved by more than 200 and 150%, respectively, on incorporation of 20 wt% PEEKOH in the NPN matrix. However, higher concentration of PEEKOH had a detrimental effect on the properties. Substitution of phenol end groups by phthalonitrile moieties led to integration of the PEEK moieties with the NPN matrix. However, it was not as conducive as PEEKOH for improving the matrix properties. The better performance of PEEKOH is attributed to the formation of polar heterocyclic groups like isoindoline by way of the phenol–nitrile reaction. © 2014 Society of Chemical Industry     

Dispersion of Poly(phenylene ether) in a Poly(phenylene sulfide)/Poly(phenylene ether) Alloy

We have devised and developed a new method for the preparation of a poly(phenylene sulfide)/poly(phenylene ether) (PPS/PPE) alloy, which has micro‐dispersed PPE in the PPS matrix. PPS was chemically treated to activate the reactivity of the PPS end‐group by extrusion in the presence of diphenylmethane diisocyanate (MDI) in its molten state at 300°C. The reactive processing of the MDI‐treated PPS with maleic anhydride‐modified PPE gave a PPS/PPE alloy with micro‐dispersed PPE in the PPS matrix. The PPS/PPE alloy showed mechanical properties superior to those of PPS at elevated temperature (150°C) and also showed precision‐molding ability superior to that of PPS.     

基于双转子连续混炼挤出机的PPS/CF复合材料制备及性能研究

采用双转子连续混炼挤出机并通过熔融共混法制备了碳纤维(CF)增强聚苯硫醚(PPS)复合材料,并对其微观形貌、动态力学性能、力学性能和导电性能进行了研究,且对相关的影响因素进行了分析。结果表明,适当降低挤出机转子转速、提高CF含量可以改善PPS/CF复合材料的力学性能和导电性能;当转子转速为200 r/min时,采用含量为20%(质量分数,下同)的CF制得的PPS/CF复合材料的冲击强度达到49. 94 J/m,体积电阻率达到60. 65Ω·cm,均优于纯PPS。     

Flammability and thermomechanical properties of dianhydride‐modified polybenzoxazine composites reinforced with carbon fiber

Composites based on carbon fiber (CF) and benzoxazine (BA‐a) modified with PMDA were investigated. The flammability of the carbon fiber composites was examined by limiting oxygen index (LOI) and UL‐94 vertical tests. The LOI values increased from 26.0 for the CF/poly(BA‐a) composite to 49.5 for the CF‐reinforced BA‐a/PMDA composites as thin as 1.0 mm and the CF‐reinforced BA‐a/PMDA composites were also achieved the maximum V‐0 fire resistant classification. Moreover, the incorporation of the PMDA into poly(BA‐a) matrix significantly enhanced the T_g and the storage modulus (E') values of the CF‐reinforced BA‐a/PMDA composites rather than those of the CF/poly(BA‐a). The T_g values and storage moduli of the obtained CF‐reinforced BA‐a/PMDA composites were found to have relatively high value up to 237°C and 46 GPa, respectively. The CF‐reinforced BA‐a/PMDA composites exhibited relatively high degradation temperature up to 498°C and substantial enhancement in char yield with a value of up to 82%, which are somewhat higher compared to those of the CF/poly(BA‐a) composite, i.e., 405°C and 75.7%, respectively. Therefore, due to the improvement in flame retardant, mechanical and thermal properties, the obtained CF‐reinforced BA‐a/PMDA composites exhibited high potential applications in advanced composite materials that required mechanical integrity and self‐extinguishing property. POLYM. COMPOS., 34:2067–2075, 2013. © 2013 Society of Plastics Engineers     

Effect of blending on the multiple melting behavior of polyphenylene sulfide

The effects of melting time (t_melt) and annealing time (t_a) at a temperature closer to the melting point of polyphenylene sulfide (PPS) on the multiple melting behavior of neat PPS, and PPS component in their blends have been investigated by differential scanning calorimetry (DSC). It is found that double endotherm peak of PPS annealed at 275°C for less than three hours is different from that annealed for twelve hours. Double endotherm peak of PPS in PEEK/PPS blends shifts to lower temperature, and the intensity of the upper melting peak decreases significantly by addition of polyether ether ketone (PEEK). An additional third melting peak could be observed. The temperature of third melting peak is above 310°C and increases as the t_a and PEEK content are increased. For PEK-C/PPS blends, the lower and upper melting temperatures of the PPS component are higher than that of neat PPS annealed at 275°C for twenty-three hours. © 1996 John Wiley & Sons, Inc. J Appl Polym Sci 63: 1001–1008, 1997     

Enhanced glass fiber-reinforced phenolphthalein poly(ether ketone) composites by blending poly(phenylene sulfide)

The mechanical properties of glass fiber-reinforced phenolphthalein poly(ether ketone)/ poly(phenylene sulfide) (PEK-C/PPS) composites have been studied. The morphologies of fracture surfaces were observed by scanning electron microscope. Blending a semicrystalline component, PPS, can improve markedly the mechanical properties of glass fiberreinforced PEK-C composites. These results can be attributed to the improvement of fiber/matrix interfacial adhesion and higher fiber aspect ratio. © 1996 John Wiley & Sons, Inc.     

Effect of high-performance polymers on crystallization and multiple melting behavior of poly(phenylene sulfide)

The crystallization and multiple melting behavior of poly(phenylene sulfide) (PPS) and its blends with amorphous thermoplastic bisphenol A polysulfone (PSF) and phenolphthalein poly(ether ketone) (PEK-C), crystalline thermoplastic poly(ether ether ketone) (PEEK), and thermosetting bismaleimide (BMI) resin were investigated by a differential scanning calorimeter (DSC). The addition of PSF and PEK-C was found to have no influence on the crystallization temperature (T_c) and heat of crystallization (ΔH_c) of PPS. A significant increase in the value of T_c and the intensity of the T_c peak of PPS was observed and the crystallization of PPS can be accelerated in the presence of the PEEK component. An increase in the T_c of PPS can also be accelerated in the BMI/PPS blend, but was no more significant than that in the PEEK/PPS blend. The T_c of PPS in the PEEK/PPS blends is dependent on the maximum temperature of the heating scans and can be divided into three temperature regions. The addition of a second component has no influence on the formation of a multiple melting peak. The double melting peaks can also be observed when PPS and its blends are crystallized dynamically from the molten state. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 637–644, 1998     

Preparation,structures and properties of interpenetrating network structure-type Phosphate/PEEK composites with enhanced compressive strength and high temperature resistance

Phosphate/polyether ether ketone (PEEK) composites were successfully prepared by molding method and thermal treating at the temperature of 360 °C. The structures and compositions of phosphate/PEEK composites were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, differential scanning calorimetry and scanning electron microscopy. The mechanical properties thermal resistance and dielectric properties were strictly evaluated by the mechanical testing, thermogravimetric analysis and dielectric constant analysis. As the results, the interpenetrating network structure (IPNS) of Al₂O₃-phosphates was completely formed in PEEK matrix. And the phosphate/PEEK composite with 40% Al₂O₃-phosphate showed a 15.9% increasing for tensile strength and 74.5% increasing for compressive strength at room temperature. Besides, the phosphate/PEEK composite with 80 wt% Al₂O₃-phosphate dispalyed a dielectric constant of 4.0, a dielectric loss of 0.0601 and a Shore hardness of 91 HD. As the structural materials, these composites would exhibited the potential applications in aviation, aerospace and other fields.