Role of surfactant in composite latex particle morphology

Composite particles were prepared by seeded emulsion polymerization at 70°C using K₂S₂O₈ as initiator and two different nonionic surfactants. Monodisperse polystyrene latex particles were used as seed and methyl methacrylate was used as second-stage monomer. When the surfactant, polyethylene oxide–propylene oxide (Pluronic F-108), was used, the final particle morphology showed that the PMMA (core) was partially covered by polystyrene. However, when nonyphenol polyethylene oxide (Igepal Co-990) was used as surfactant, one observed a reversed type of encapsulation (i.e., PS core is partially engulfed by PMMA). The interfacial tensions of the polymer phase against water containing the appropriate surfactant were measured by the drop-volume method and used in a mathematical model based on thermodynamic analysis to predict the equilibrium particle morphology. The observed particle morphologies were found to differ from the predicted morphologies at low conversion of the second-stage monomer but agreed with it at higher conversion.     

Morphologies of polybutylacrylate/poly(styrene‐co‐methyl methacrylate) latex prepared by starved emulsion polymerization Part I. Thermodynamics equilibrium morphology

Heterogeneous latexes were prepared by a semicontinuous seeded emulsion polymerization process under monomer starved conditions at 80 °C using potassium persulfate as the initiator and sodium dodecyl sulfate as the emulsifier. Poly(butyl acrylate) latexes were used as seeds. The second‐stage polymer was poly(styrene‐co‐methyl methacrylate). By varying the amounts of methyl methacrylate (MMA) in the second‐stage copolymer, the polarity of the copolymer phase could be controlled. Phase separation towards the thermodynamic equilibrium morphology was accelerated either by ageing the composite latex at 80 °C or by adding a chain‐transfer agent during polymerization. The morphologies of the latex particles were examined by transmission electron microscopy (TEM). The morphology distributions of latex particles were described by a statistical method. It was found that the latex particles displayed different equilibrium morphologies depending on the composition of the second‐stage copolymers. This series of equilibrium morphologies of [poly(butyl acrylate)/poly(styrene‐co‐methyl methacrylate)] (PBA/P(St‐co‐MMA)) system provides experimental verification for quantitative simulation. Under limiting conditions, the equilibrium morphologies of PBA/P(St‐co‐MMA) were predicted according to the minimum surface free energy change principle. The particle morphology observed by TEM was in good agreement with the predictions of the thermodynamic model. Therefore, the morphology theory for homopolymer/homopolymer composite systems was extended to homopolymer/copolymer systems. © 2002 Society of Chemical Industry     

Development of morphology in latex particles: The interplay between thermodynamic and kinetic parameters

A thermodynamic analysis and a mathematical model were developed to describe the free energy changes corresponding to various possible morphologies in composite latex particles. Two experimental composite latex systems were used to verify and establish limitations of the model. The two latex systems were based on polystyrene/poly(methyl methacrylate), one prepared by conventional seeded emulsion polymerization and the second system by direct emulsification of a solution of a blend of the two polymers. The influence of several experimental parameters on latex particle morphology was investigated. These included monomer/polymer ratio, surfactant type, and initiator type in the seeded emulsion polymerization system. The influence of local viscosity, shear effects, and molecular weights of polymers were investigated in the artificial latex system.     

Morphology and thermodynamic analysis of composite polymer particles prepared by soap‐free emulsion polymerization in the presence of poly(methyl methacrylate) and polystyrene as biseeds

Biseeds emulsion polymerization was investigated with poly(methyl methacrylate) (PMMA) and polystyrene (PSt) as biseeds and styrene (St) as second‐stage monomer, as well as with thermodynamic analysis; namely, the principle of minimum interfacial free‐energy change was utilized to explain the competitiveness of different seeds for second‐stage monomer and the final equilibrium morphology of composite polymer particles. The experimental results indicated the polymeric particles prepared had bimodal size distribution and the PMMA seed particles showed a higher chance of obtaining St than that of the PSt seed particles, which was in agreement with the computational outcome by the principle of minimum interfacial free‐energy change. Owing to the kinetic factors, the equilibrium morphology could not be reached in the experiments. However, the results demonstrated that double or multiple seeds emulsion polymerization could be used as a model experiment to study the morphology of polymer particle and the morphological prediction. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2675–2680, 2004     

Morphology of poly(butyl acrylate)/poly(styrene‐co‐methyl methacrylate) latex prepared by starved emulsion polymerization: II. Development of particle morphology

Heterogeneous latexes were prepared by a two‐stage seeded emulsion polymerization process under monomer starved conditions at 80 °C using potassium persulfate as the initiator and sodium dodecyl sulfate as the emulsifier. Poly(butyl acrylate) latexes were used as seeds. The second‐stage polymer was poly(styrene‐co‐methyl methacrylate). By varying the amount of methyl methacrylate (MMA) in the second‐stage copolymer, the polarity of the copolymer phase could be controlled. It was found that the latex particles displayed different morphologies depending on the monomer ratio. The amount of MMA had a significant effect on the evolution of morphology. The morphologies were observed by transmission electron microscopy. In addition, the evolution of the particle morphology was predicted by the mathmatical model for cluster migration. The model gave the same trends as the experimental results. © 2002 Society of Chemical Industry     

Effects of compatibilizing agents in poly(n-butyl acrylate)/poly(methyl methacrylate) composite latexes

Graft copolymers with poly(n-butyl acrylate) (PBA) backbones and poly(methyl methacrylate) (PMMA) macromonomer side chains are used as compatibilizing agents for PBA/PMMA composite latexes. The composite latexes are prepared by seeded emulsion polymerization of methyl methacrylate (MMA) in the presence of PBA particles. Graft copolymers were already incorporated into the PBA particles prior to using these particles as seed via miniemulsion (co)polymerization of n-butyl acrylate (BA) in the presence of the macromonomers. Comparison between size averages of composite and seed particles indicates no secondary nucleation of MMA during seeded emulsion polymerization. Transmission electron microscopy (TEM) observations of composite particles show the dependence of particle morphologies with the amount of macromonomer (i.e., mole ratio of macromonomer to BA and molecular weight of macromonomer) in seed latex. The more uniform coverage with the higher amount of macromonomer suggests that graft copolymers decrease the interfacial tension between core and shell layers in the composite particles. Dynamic mechanical analysis of composite latex films indicates the existence of an interphase region between PBA and PMMA. The dynamic mechanical properties of these films are related to the morphology of the composite particles, the arrangement of phases in the films, and the volume of the interphase polymer. © 1997 John Wiley & Sons, Inc.     

聚苯乙烯-聚甲基丙烯酸甲酯核-壳粒子的制备

由种子乳液聚合法制备了聚苯乙烯-聚甲基丙烯酸甲酯核-壳粒子。以过硫酸钾(KPS)为引发剂,辛基酚聚氧乙烯醚(OP-10)为乳化剂,合成了聚苯乙烯(PS)种子核;连续滴加甲基丙烯酸甲酯(MMA),在核表面富集MMA,制备了粒径范围在0.16~0.67μm的核-壳粒子;当单体苯乙烯与甲基丙烯酸甲酯(St/MMA)的比为30∶70(质量比)时,所得粒径在0.18μm,粒径分布为0.012。差示扫描量热(DSC)研究显示,复合粒子的玻璃化转变温度(Tg)为97.2℃,峰形单一,表现出良好的热性能。     

Study on synthesis and morphology control of poly(4‐vinylpyridine‐co‐butyl acrylate)/poly(styrene‐co‐butyl acrylate) composite microspheres

Monodispersed crosslinked cationic poly(4‐vinylpyridine‐co‐butyl acrylate) [P(4VP‐BA)] seed latexes were prepared by soapless emulsion polymerization, using 2,2′‐azobismethyl(propionamidine)dihydrochloride (V₅₀) as an initiator and divinylbenzene (DVB) or ethylene glycol dimethacrylate (EGDMA) as a crosslinker. The optimum condition to obtain monodispersed stable latex was investigated. It was found that the colloidal stability of the P4VP latex can be improved by adding an adequate amount of BA (BA/4VP = 1/4, w/w), and adopting a semicontinuous monomer feed mode. Subsequently, poly(4‐vinylpyridine‐co‐butyl acrylate)/Poly(styrene‐co‐butyl acrylate) [P(4VP‐BA)/P(ST‐BA)] composite microspheres were synthesized by seeded polymerization, using the above latex as a seed and a mixture of ST and BA as the second‐stage monomers. The effects of the type of crosslinker, the degree of crosslinking, and the initiators (AIBN and V₅₀) on the morphology of final composite particles are discussed in detail. It was found that P(4VP‐BA)/P(ST‐BA) composite microspheres were always surrounded by a PST‐rich shell when V₅₀ was used as initiator, while sandwich‐like or popcorn‐like composite particles were produced when AIBN was employed. This is because the polarity of the polymer chains with AIBN fragments is lower than for the polymer with V₅₀ fragments, hence leading to higher interfacial tension between the second‐stage PST‐rich polymer and the aqueous phase, and between PST‐rich polymer and P4VP‐rich seed polymer. As a result, the seed cannot be engulfed by the PST‐rich polymer. Furthermore, the decrease of T_g of the second‐stage polymer promoted phase separation between the seeds and the PST‐rich polymer: sandwich‐like particles formed more preferably than popcorn‐like particles. It is important knowledge that various morphologies different from PST‐rich core/P4VP‐rich shell morphology, can be obtained only by changing the initiator, considering P4VP is much more hydrophilic than PST. The zeta potential of composite particles initiated by AIBN in seeded polymerization shifted from a positive to a negative charge. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1190–1203, 2002     

STUDIES ON SYNTHESIS OF SILICA SOL-ORGANIC POLYMER COMPOSITE EMULSION

An emulsion of polystyrene/poly (butylacrylate-methyl methacrylate acrylic acid) core/shell latex particles (PS/P (BA-MMA-AA)) has been prepared by use of three synthetic methods. The effects of synthetic methods on the distribution of carboxyl groups in latex particles were studied. The results show that the seed emulsion polymerization in which the pre-emulsified monomers were added by dropping method to the second stage is the best technique for obtaining the optimum distribution of carboxyl groups on the surface of the latex particles. Furthermore, by using PS/P (BA-MMA-AA), a type of novel composite emulsion of silica sol-PS/P (BA-MMA-AA) was synthesized with the above method. By observation through transmission EM, the morphology of the latex particles obtained shows that a composite structure has been formed between silica sol particles and organic polymer particles.     

核壳结构聚硅氧烷/丙烯酸酯复合乳液(Ⅰ)乳化剂对乳液聚合过程及粒径分布和粒子形态的影响

采用种子乳液半连续法合成了具有高有机硅含量的聚硅氧烷/丙烯酸酯核壳结构复合乳液,研究乳化剂的种类、复配比例及质量浓度对有机硅／丙烯酸酯壳核乳液性能与乳胶粒径、分布和结构的影响.结果表明：阴离子乳化剂十二烷基硫酸钠(SDS)、十二烷基磺酸钠(SDS-2)、十二烷基苯磺酸钠(SDBS)所合成的乳胶粒子粒径依次增大,SDS与非离子型乳化剂OP-10复配使用时,随OP-10质量分数的增加,聚合速率和转化率降低,化学稳定性增加,乳胶粒子粒径增大,分布变宽,确定了复合乳化剂的最佳配比.随复合乳化剂浓度的增加,聚合速率加快、转化率增加,乳胶粒子粒径减小而分布加宽.通过改变乳化剂加入方式可减小乳胶粒子的粒径分布.为减少壳层聚合物新粒子的产生,需严格控制乳化剂的浓度,使加入的壳层单体处于“饥饿”状态,在乳胶粒子表面富集、引发聚合,形成表层“过渡层”,最终形成核壳结构复合粒子.     

Preparation of polystyrene/poly(methyl methacrylate) core‐shell composite particles by suspension‐emulsion combined polymerization

Suspension‐emulsion combined polymerization process, in which methyl methacrylate (MMA) emulsion polymerization constituents (EPC) were drop wise added to styrene (St) suspension polymerization system, was applied to prepare polystyrene/poly(methyl methacrylate) (PS/PMMA) composite particles. The influences of the feeding condition and the composition of EPC on the particle feature of the resulting composite polymer particles were investigated. It was found that PS/PMMA core‐shell composite particles with a narrow particle size distribution and a great size would be formed when the EPC was added at the viscous energy dominated particle formation stage of St suspension polymerization with a suitable feeding rate, whereas St‐MMA copolymer particles or PS/PMMA composite particles with imperfect core‐shell structure would be formed when the EPC was added at the earlier or later stage of St suspension polymerization, respectively. It was also showed that the EPC composition affected the composite particles formation process. The individual latex particles would exist in the final product when the concentrations of MMA monomer, sodium dodecyl sulfate emulsifier, and potassium persulfate initiator were great in the EPC. Considering the feature of St suspension polymerization and the morphology of PS/PMMA composite particles, the formation mechanism of PS/PMMA particles with core‐shell structure was proposed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

中空聚合物微球的制备——种子及核乳胶粒的制备

为了制得具有中空结构的聚合物微球,首先以十二烷基苯磺酸钠(SDBS)为乳化剂,在其用量低于CMC的条件下,进行甲基丙烯酸甲酯(MMA)、甲基丙烯酸(MAA)和丙烯酸丁酯(BA)的乳液聚合,制备了带羧基的种子乳胶粒.然后采用MMA、MAA和二乙烯基苯为单体进行种子乳液聚合,制备了轻度交联的带羧基的核乳胶粒.该核乳胶粒经过核-壳乳液聚合和适当的碱处理工艺就可成为具有中空结构的聚合物微球.采用粒度仪测定了乳胶粒的直径及其分布,采用TEM对乳胶粒结构形态进行了表征.研究了种子及核乳胶粒制备过程中单体加料方式、乳化剂用量及羧基单体种类等因素对聚合稳定性、乳胶粒直径及其分布以及最终的中空聚合物微球结构形态的影响,确定了制备种子及核乳胶粒的最佳工艺条件.在制备种子阶段,SDBS用量为单体总量的0.5%,采用一次性加入单体的进料工艺;在核乳胶粒制备阶段,以MAA为羧基单体,所有单体采用"饥饿式"加料,半连续补加乳化剂并使乳化剂用量为核单体总量的0.15%时可保持聚合稳定性并保证无新乳胶粒生成.     

Self‐assembly of pH‐responsive acrylate latex particles at emulsion droplets interface

The self‐assembly of pH‐responsive poly (methyl methacrylate‐co‐acrylic acid) latex particles at emulsion droplet interfaces was achieved. Raising pH increases the hydrophilicity of the latex particles in situ and the latex particle acts as an efficient particulate emulsifier self‐assembling at emulsion droplet interface at around pH 10–11 but exhibits no emulsifier activity at higher pH. This effect can be reversibly induced simply by varying the aqueous phase pH and thus the latex emulsifier can be reassembled. The effect factors, including the aqueous phase pH, the surface carboxyl content, ζ‐Potential of the latex particles and oil phase solvent have been investigated. Using monomer as oil phase, the latex particles could stabilize emulsion droplets during polymerization and cage‐like polymer microspheres with hollow core/porous shell structure were obtained after polymerization. The mechanism of the latex particles self‐assembly was discussed. The morphologies of emulsion and microspheres were characterized by optical microscopy, scanning electron microscopy, and transmission electron microscopy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of acrylic acid and hydroxyethyl methacrylate modified nano-SiO2 particles on poly(methyl methacrylate-hydroxyethyl methacrylate) soap-free emulsion polymerization

Nano-SiO₂ powder was modified with acrylic acid (AA) and hydroxyethyl methacrylate (HEMA), respectively. The kinetics of the soap-free emulsion polymerization of methyl methacrylate (MMA) and HEMA in the presence of unmodified or modified nano-SiO₂ particles was investigated. The structure of the nano-SiO₂ particles and the Poly(MMA-HEMA) composite emulsion was characterized by Fourier transform infrared spectroscope (FT-IR). The particle size and size distribution of the emulsion, the morphology of emulsion particle, the surface tension, and ionic conductivity of these systems before and after polymerization were determined. The IR spectra showed that the organic modifiers were incorporated onto the surface of the nano-particles. In addition, the solid content and monomer conversion of the Poly(MMA-HEMA) composite emulsion with modified nano-SiO₂ are higher than that with original inorganic particles. The particle size became smaller and the particle distribution narrowed after applying the modified nano-SiO₂ particles. The SEM observation demonstrated that the shapes of these emulsion particles were uniform sphere. The surface tension and ionic conductivity increased significantly after polymerization.     

Morphology of latex particles formed by poly(methyl methacrylate)-seeded emulsion polymerization of styrene

Poly(methyl methacrylate)–polystyrene composite particle latexes were prepared by poly(methyl methacrylate)-seeded emulsion polymerization of styrene employing batch, swelling-batch, and semibatch methods. The changes in particle morphology taking place during the polymerization reaction were followed by electron microscopy. Anchoring effect exerted by ionic terminal groups introduced by ionic initiator was found to be the main factor in controlling the particle morphology. The polymer particles obtained by oil-soluble hydrophobic initiators such as azobisisobutyronitrile and 4,4′-azobis-(4-cyanovaleric acid) gave the inverted core-shell morphology. Water-soluble hydrophilic initiator, K₂S₂O₈, also gave the inverted core-shell morphology. However, in this case the occurrence of the halfmoonlike, the sandwichlike, and the core-shell morphologies were also observed depending upon the polymerization conditions. The distribution of terminal ? SO groups on the surface area of polystyrene particles could be controlled by initiator concentration and polymerization temperature. Viscosity of polymerization loci dictated the movement of polymer molecules, thus causing the unevenness of particle shape and phase separation at high viscosity state. Viscosity was controlled by the styrene/poly(methyl methacrylate) ratio, the addition of a chain transfer agent or a solvent which is common to polystyrene and poly(methyl methacrylate).     

Novel method of preparation of a charged mosaic membrane by using dipole‐like microspheres. II. Preparation of dumbbell/egg‐like microspheres

The dumbbell‐like/egglike microspheres of poly(4‐vinylpyridine/n‐butyl acrylate)/polystyrene [P(4VP/nBA)/PS] were prepared by soap‐free seed emulsion polymerization. The effects of various polymerization parameters, such as the amount of ethyl acetate (EA) in the continuous phase, swelling time, degree of crosslinking of seed polymer, polymerization temperature, and compatibility of seed polymer and the secondary polymer, and so forth, on the formation of dumbbell‐like/egglike morphology were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It was found that secondary particles could be eliminated either by drastically increasing the number of seed particles or by stripping EA from the seed latex by dialysis and evaporation under a vacuum. Swelling the seed particle with the secondary monomer was essential for the preparation of egglike microspheres. For the localization of PS domains on one side of the egglike particle, the most effective factors were to elevate the polymerization temperature up to 90°C and simultaneously to lower the compatibility of the polymer on the seed particle surface with the phase of PS, while using the uncrosslinked seed latex. Crosslinking the seed latex was not suitable for localizing the PS domains in the seed particle, especially when the degree of crosslinking exceeded 0.5 wt % of EGDMA. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2002–2017, 2001     

Kinetic study on the poly(methyl methacrylate) seeded soapless emulsion polymerization of styrene. I. Experimental investigation

In this work, methyl methacrylate (MMA) and styrene (ST) were used as monomers in the first stage and second stage of polymerization, respectively, and potassium persulfate (K₂S₂O₈) was used as the initiator to synthesize the poly(methyl methacrylate)-polystyrene (PMMA/PS) composite latex by the method of two-stage soapless emulsion polymerization, i.e., PMMA seeded soapless emulsion polymerization of styrene. The morphology of the latex particles was observed by transmission electron microscopy (TEM). It showed that the composite latex particles had a core–shell structure. The particlesize distribution of the composite latex was very uniform. The kinetic data of seeded soapless emulsion polymerization showed that the square root of polymer yield (Wp)^1/2 was proportional to the reaction time in the earlier period of the reaction. The slope of the line of (Wp)^1/2 vs. reaction time was independent of the content of the seed, but proportional to 0.5 power of the initiator concentration. The gel effect was apparent after monomer droplets disappeared. A glassy effect was found in the latter period of the reaction. The number-average molecular weight of the polymers increased but the weight-average molecular weight of the polymers decreased with decrease of the MMA/ST weight ratio. The number- and weight-average molecular weight increased with decreasing the temperature significantly. © 1995 John Wiley & Sons, Inc.     

Swelling of poly(styrene-co-methacrylic acid) latex by isoprene

Carboxylated polystyrene latex was used as seed and isoprene as the second-stage monomer in an inhibited, seeded emulsion polymerization recipe for studies of monomer swelling kinetics at 80°C during interval III of an emulsion polymerization. The isoprene was added to the reactor in small portions using a syringe, and changes in the reactor pressure were continuously measured. Isoprene was added until a free liquid monomer phase was formed; that was, interval II was reached, as indicated by no further pressure increase upon the addition of more monomer. When the observed pressure increment, Op_i, per unit isoprene added was plotted as a function of the volume fraction of polymer in the latex particles, v_p, the graph could be divided into 3 domains. The break points in the Op_i curve could, in an analogous emulsion polymerization, be identified as the glass transition temperature for the polymer, the so-called gel point in interval III and the onset of interval III. In the second domain, where the v_p was between the glass transition temperature, T_g, for the seed polymer and the gel point, the value of Op_i decreased significantly with increasing monomer concentration in the latex particles. This was due to the entropy of mixing and the monomer acting as a plasticizer in the seed polymer. The rate of sorption of monomer to the latex particles was low at high values of v_p. It then increased rapidly with increasing monomer concentrations in the latex particles, [M]_p, and a maximum was observed in domain 2. At lower values of v_p the sorption rate decreased in domain 3 and finally became zero as the free liquid monomer phase started to form. Results from batch polymerization suggested that the rate of diffusion of adsorbed monomer and oligo radicals into the particles was retarded. A simplified form of the Vanzo equation was used to estimate the monomer partitioning. It predicted too high a value of [M]_p, especially in domain 2 of the swelling process. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 2041–2051, 1998     

Preparation of hemispherical poly(4‐vinylpyridine‐co‐butyl acrylate)/poly(styrene‐co‐butyl acrylate) composite microspheres by seeded preswelling emulsion polymerization

Seeded preswelling emulsion polymerization was carried out by using monodispersed poly(4‐vinylpyridine‐co‐butyl acrylate) [P(4VP‐BA)] particles as the seed, and styrene and butyl acrylate as the second‐stage monomers under different polymerization conditions, to obtain hemispherical polystyrene (PST)‐rich–P4VP‐rich microspheres. Prior to polymerization, toluene was added into the preswelling system together with the second‐stage monomers. It was found that, with the increase of the amount of toluene, the particle morphology showed a tendency toward desirable hemispherical structure, and the colloidal stability of composite latex was improved. When the weight ratio of toluene/seed latex was increased up to 7.5/40 (g/g), the stable hemispherical latex could be obtained. However, when toluene was not added, the coagulum formed on the wall of the reactor during polymerization, and the composite particles with multiple surface domains (such as sandwich‐like, popcorn‐like) were formed. In addition, the final morphology of composite particles was influenced by the polarity of the seed crosslinker and the hydrophilicity of the second‐stage initiator, which could affect the mobility of poly(styrene‐co‐butyl acrylate) [P(ST‐BA)] chains. The morphology development during the polymerization was investigated in detail, and a schematic model was derived to depict the formation mechanism of hemispherical P(4VP‐BA)/P(ST‐BA) composite microspheres. The results revealed that the mobility of the P(ST‐BA) chains influenced the diffusion of the P(ST‐BA) domains on the surface of the P(4VP‐BA) matrix. When the mobility of the P(ST‐BA) chains allowed small‐size P(ST‐BA) domains to coalesce into one larger domain, complete phase‐separated morphology (hemisphere) could be achieved. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3811–3821, 2003     

Synthesis and properties of amphiphilic nonspherical SPS/PS composite particles by multi-step seeded swelling polymerization

Amphiphilic nonspherical particles have asymmetric surface physical and chemical properties. Such a unique structure makes them suitable for applications in many areas, such as chemical and biological sensors, colloidal surfactants, self-assembly, building blocks of complex superstructures, and materials engineering. In this study, amphiphilic sulfonated polystyrene/polystyrene (SPS/PS) composite particles with controllable morphologies are synthesized by combining modified treatment and multistage seeded swelling polymerization. Core-shell SPS particles were first obtained by modifying cross-linked PS particles with concentrated sulfuric acid, and the surface of SPS particles was a hydrophilic sulfonated polystyrene layer. With further twice seeded swelling polymerization, new hydrophobic PS oil phase sprouted on the strong hydrophilic surface even without any surfactant assistance in aqueous media. The morphologies of these SPS/PS composite particles could be adjusted by changing the crosslinking density of the seed microspheres, the sulfonation temperature and the swelling ratio of monomer/seed. These polymer composite particles can be used as solid surfactants.