Friction and wear properties of metal powder filled PTFE composites under oil lubricated conditions

Four kinds of polytetrafluoroethylene (PTFE)-based composite, pure PTFE, PTFE+30vol.%Cu, PTFE+30vol.%Pb and PTFE+30vol.%Ni composite, were prepared. The friction and wear properties of these metal powder filled PTFE composites sliding against GCr15 bearing steel under both dry and lubricated conditions were studied using an MHK-500 ring-block wear tester. The worn surfaces of the PTFE composites and the transfer films formed on the surface of GCr15 bearing steel were examined using scanning electron microscopy (SEM) and optical microscopy respectively. Experimental results show that the friction and wear properties of the PTFE composites can be greatly improved by liquid paraffin lubrication. The wear of these PTFE composites can be decreased by at least 1 to 2 orders of magnitude compared with that under dry friction conditions, while the friction coefficients can be decreased by 1 order of magnitude, SEM and optical microscopy investigations of the rubbing surfaces show that metal fillers of Cu, Pb and Ni not only raise the load carrying capacity of the PTFE composites, but also promote transfer of the PTFE composites onto the counterfaces, so they greatly reduce the wear of the PTFE composites. However, the transfer of these PTFE composites onto the counterfaces can be greatly reduced by liquid paraffin lubrication, but transfer still takes place.     

润滑油添加剂对聚合物及其复合材料摩擦磨损性能的影响

利用MHK-500型环-块磨损试验机研究了二烷基二硫代磷酸锌(ZDDP)对几种聚合物及其复合材料-金属摩擦副油润滑摩擦磨损性能的影响。结果表明,液体石蜡中的ZDDP对尼龙66(PA66)及聚酰亚胺(PI)-GCr15轴承钢摩擦副的摩擦系数影响不大,但却使聚四氟乙烯(PTEE)及其复合材料-GCr15轴承钢摩擦副的摩擦系数略有降低。PTEE及其复合材料-GCr15轴承钢摩擦副表面的ZDDP吸附膜具有一定的抗磨作用,它大幅度降低了Pb、PbO及MoS     

Tribological properties of metal-plastic multilayer composites under oil lubricated conditions

Three kinds of metal-plastic multilayer composites, which were composed of a steel backing, a middle layer of sintered porous bronze and a surface layer of polytetrafluoroethylene (PTFE) filled by Pb or Cu₂O powders, were prepared. The friction and wear properties as well as the limiting pressure times velocity (PV) values of these metal-plastic multilayer composites sliding against 45 carbon steel under both dry and oil lubricated conditions were evaluated on a MPV-1500 friction tester with a steel axis rotating on a journal bearing. The worn surfaces of these metal-plastic multilayer composites and the transfer films formed on the surface of steel axis were examined by electron probe microscopy analysis (EPMA). Experimental results show that filling of Pb to PTFE reduces the friction coefficient and wear of the composite, while filling of Cu₂O to PTFE increases the friction coefficient but decreases the wear of the composite. The friction and wear properties as well as the limiting PV values of these metal-plastic multilayer composites can be greatly improved with the oil lubrication. EPMA investigations show that Pb and Cu₂O fillers preferentially transfer onto the surfaces of steel axis, which may enhance or deteriorate the adhesion between transfer films and steel surfaces. Meanwhile the transfer of these metal-plastic multilayer composites onto the steel surface can be greatly reduced with oil lubrication, which results in the remarkable decrease of the wear of these metal-plastic multilayer composites.     

润滑油添加剂对聚合物材料摩擦磨损性能的影响研究

利用MM－200型磨损试验机考察了ZDDP对聚合物材料（PTFE、PI及MCPA）－GCr15轴承钢摩擦副摩擦磨损性能的影响。研究发现，液体石蜡及含ZDDP的液体石蜡润滑均可大幅度改善聚合物材料的摩擦磨损性能，且使其摩擦系数比干摩擦时降低一个数量级，摩擦副表面的ZDDP吸附膜均在不同程度上提高聚合物材料的耐磨性，但其对聚合物材料的摩擦性能影响不大。     

The tribological characteristics of JS material under lubrication of oil

A material composed of a steel backing, a sintered porous bronze middle layer and a layer of reinforced PTFE, which is named JS material, was prepared. The friction, wear and limiting PV values of this material under dry friction as well as the lubrication of number 20 mechanical oil were studied using a MPV-1500 friction tester. The worn surface of JS material and the transfer film formed on the counterface of carbon steel were investigated using scanning electron microscopy (SEM) and electron probe microanalysis (EPMA). The results show that the friction, wear and limiting PV values of JS material can be greatly improved with the lubrication of oil. The results of SEM and EPMA analyses indicate that, under dry friction conditions, the solid lubricant PTFE and Pb easily transfer to the steel counterface and results in the reduction of friction and wear; while under the lubrication of oil, little transference of PTFE and Pb to the steel surface occurs and very small friction and wear are achieved. Analyses of frictional surfaces also suggest that the Pb filler gets enrichment on the rubbing surfaces, which is beneficial in increasing the adhesion of the transfer film with the steel surface.     

Friction and wear behaviour of Sialon/ (Ca,Mg)‐Sialon with lubrication by coated PbS nanoparticles as oil additives

The friction and wear behaviour of Sialon/(Ca,Mg)‐Sialon with lubrication by liquid paraffin containing PbS nano‐particles coated with dialkyldithiophosphate or oleic acid as additives was investigated using an SRV ball‐on‐disc test rig. It was found that the addition of such nanoparticles reduced the friction coefficient of the friction couple irrespective of the concentration of the additive and the wear volume of (Ca,Mg)‐Sialon, especially under relatively high loads such as 150 N or more. X‐ray photoelectron spectroscopy and electron probe microanalysis revealed that a tribochemical film composed of PbSO₄, PbS₂O₃, PbSO₃, etc., was formed on the worn surface, and contributed to the lubricity of the PbS nanoparticles.     

On the friction and wear behavior of PTFE composite filled with rare earths treated carbon fibers under oil-lubricated condition

Carbon fibers (CF) were surface treated with air-oxidation, air-oxidation followed by rare earths (RE) treatment and RE treatment, respectively. The friction and wear properties of the polytetrafluoroethylene (PTFE) composites filled with differently surface treated carbon fibers, sliding against GCr15 steel under oil lubrication, were investigated on a reciprocating ball-on-disk UMT-2MT tribometer. The worn surfaces of the PTFE composites were examined using a scanning electron microscopy (SEM). Experimental results revealed that surface treatment of carbon fibers reduced the wear of CF-reinforced PTFE composites. Among all the treatments to carbon fibers, RE treatment was the most effective and lowest friction and wear rate of CF-reinforced PTFE composite was exhibited, owing to the effective improvement of the interfacial adhesion between the carbon fibers and PTFE matrix.     

A study on friction and wear characteristics of nanometer Al2O3 /PEEK composites under the dry sliding condition

The friction and wear properties of the polyetheretherketone (PEEK) based composites filled with 5 mass% nanometer or micron Al₂O₃ with or without 10 mass% polytetrafluroethylene (PTFE) against the medium carbon steel (AISI 1045 steel) ring under the dry sliding condition at Amsler wear tester were examined. A constant sliding velocity of 0.42 m s⁻¹ and a load of 196 N were used in all experiments. The average diameter 250 μm PEEK powders, the 15 or 90 nm Al₂O₃ nano-particles or 500 nm Al₂O₃ particles and/or the PTFE fine powders of diameter 50 μm were mechanically mixed in alcohol, and then the block composite specimens were prepared by the heat compression moulding. The homogeneously dispersion of the Al₂O₃ nano-particles in PEEK matrix of the prepared composites was analyzed by the atomic force microscopy (AFM). The wear testing results showed that nanometer and micron Al₂O₃ reduced the wear coefficient of PEEK composites without PTFE effectively, but not reduced the friction coefficient. The filling of 10 mass% PTFE into pure PEEK resulted in a decrease of the friction coefficient and the wear coefficient of the filled composite simultaneously. However, when 10 mass% PTFE was filled into Al₂O₃/ PEEK composites, the friction coefficient was decreased and the wear coefficient increased. The worn scars on the tested composite specimen surfaces and steel ring surfaces were observed by scanning electron microscopy (SEM). A thin, uniform, and tenacious transferred film on the surface of the steel rings against the PEEK composites filled with 5 mass% 15 nm Al₂O₃ particles but without PTFE was formed. The components of the transferred films were detected by energy dispersive spectrometry (EDS). The results indicated that the nanometer Al₂O₃ as the filler, together with PEEK matrix, transferred to the counterpart ring surface during the sliding friction and wear. Therefore, the ability of Al₂O₃ to improve the wear resistant behaviors is closely related to the ability to improve the characteristics of the transfer film.     

Experimental Evaluation of Friction and Wear Properties of Solid Lubricant Coatings on SUS440C Steel in Liquid Nitrogen

The friction and wear properties of the prevailing different solid lubricant coatings (Ion-plated Au, Ion-plated Ag and RF-sputtered PTFE on SUS440C stainless steel) used in the bearings of high-speed cryogenic-turbo-pumps of liquid rocket engines were experimentally evaluated in liquid nitrogen immersed conditions. Also the above experiments were carried out with two newly proposed solid lubricant coatings of sputter-ion-plated MoSTi and a new ion-plated Pb on SUS440C stainless steel. The friction coefficient and wear rates of the coatings of ion-plated Au, ion-plated Ag, RF-sputtered PTFE, the new ion-plated Pb and MoS₂Ti-SIP (with coating thickness of 0.7±0.1 μm) on SUS440C steel against SUS440C stainless steel ball in liquid nitrogen were compared. Worn surfaces were examined microscopically with a microscope and a profilometer for understanding the mechanisms of friction and wear and transfer film lubrication in liquid nitrogen. It is found that the newly proposed solid lubricant coatings are showing promising results for their use in liquid nitrogen immersed conditions. The sputter-ion-plated MoSTi coating on SUS 440C steel shows a minimum value of friction coefficient (μ=0.015) and wear rate (w_c=0.56 × 10⁻⁶ mm³/N m ) in liquid nitrogen.     

Effect of Sliding Speed and Applied Load on Dry Sliding Tribological Performance of TiAl Matrix Self-lubricating Composites

More durable, low-friction self-lubricating materials in modern industry are greatly needed for tribological systems. The current paper presents the tribological performance of TiAl matrix self-lubricating composites (TSC) containing MoS₂, hexagonal BN and Ti₃SiC₂ designated as MhT against GCr15 steel counterface under several sliding speeds from 0.2 to 0.8 m s^?1 and applied loads from 6 to 12 N. The results suggested that MhT played an important role in decreasing friction coefficients and wear rates. The covering percentage of transfer layers on worn surfaces varied with the changing of sliding speeds and applied loads, hence resulting in the distinct friction and wear characteristics of TSC. TSC containing 10 wt% MhT exhibited the best excellent tribological performance at 10 N–0.8 m s^?1, which could be due to the formation of the best compaction and largest coverage of transfer layer on the worn surfaces.     

GCr15及G20CrNi2Mo轴承钢高温润滑条件下摩擦磨损性能

为了探究轴承钢在高温润滑条件下的摩擦磨损性能,采用扫描电子显微镜(SEM)、X射线衍射仪(XRD)、洛氏硬度计等对GCr15高碳轴承钢和G20CrNi2Mo渗碳轴承钢组织、物相及硬度进行了表征,利用QG-700型气氛高温摩擦磨损试验机研究轴承钢材料不同条件下的高温润滑摩擦磨损性能,并分析其磨损机制.结果表明:2种轴承钢...     

Tribological Behavior of PTFE Composites Filled with PEEK and Nano-Al2O3

In this study, the tribological properties of polytetrafluoroethylene (PTFE) composites filled with polyetheretherketone (PEEK) and nano-Al₂O₃ particles were studied using a block-on-ring wear tester. The tribological performance of the composites was affected by the experimental parameters (sliding speed, normal load, and environmental temperature) and the composites achieved a high-speed sliding friction state. The results showed that the PEEK and nano-Al₂O₃ particles significantly improved the wear resistance of the PTFE composites. In addition, the nano-Al₂O₃ particles increased the hardness of the composites and enhanced the mechanical properties to enable applications in a wider range of industrial fields. The effects of the sliding speed and normal load on the tribological properties were more significant than that of the environmental temperature. In addition, the entire wear process was divided into three stages (the initial wear stage, severe wear transition stage, and ultralow stable wear stage), according to the evolution of the tribological characteristics (wear rate, morphology of the worn surface and transfer film, and wear debris morphology).     

纳米ZnO填充的PTFE基复合材料摩擦学性能研究

得胜０００型摩擦磨损试验机研究了不同体积含量的纳米氧化锌（ＺｎＯ）填充的ＰＴＦＥ基复合材料在于摩擦条件下与不风对摩时的摩擦学性能,并利用扫描电子微镜（ＳＥＭ）对ＰＴＦＥ及纳米ＺｎＯ／ＰＴＦＥ复合材料的微观结构、磨损表面和转移膜进行了观察和分析。结果表明,纳米ＺｎＯ／ＰＴＦＥ复合材料的摩擦性能与纯ＰＴＦＥ基本相当,但耐磨性明显优于后者,纳米ＺｎＯ在复合材料中的最佳含量为１５ｖｏｌ．％左右。     

Microstructure of PTFE-Based Polymer Blends and Their Tribological Behaviors Under Aqueous Environment

Four polytetrafluoroethylene-based polymer blends (PTFE blends) with polyimide (PI), polyether ether ketone (PEEK), poly(phenyl p-hydroxybenzoate) (PHBA), and perfluoroethylene propylene copolymer (FEP) were prepared by compression molding and follow-up sintering. Their microstructure was observed by scanning electron microscope. And the tribological behaviors of PTFE blends sliding against 316 steel under pure water and sea water lubrication were comparatively evaluated using block-on-ring tribology test rig. The worn surface of counterpart was examined by X-ray photoelectron spectroscopy. The results showed that by blending with the four polymers, PTFE exhibited the transformed microstructure and improved wear resistance. Compared with FEP, rigid polymers PI, PHBA, and PEEK can enhance the wear resistance of PTFE greatly because they can effectively improve the load-carrying capacity of PTFE matrix and can more efficiently prevent the crystalline bands of PTFE from being pulled out. However, because of the weak inhibition on the pulling out of PTFE crystalline bands, FEP cannot enhance the wear resistance of PTFE as significantly as other polymers. In addition, the friction coefficients and wear rates of PTFE and its blends were lower under the lubrication of sea water than under the lubrication of pure water, which was ascribed to more excellent lubricating effect of sea water originating from the deposition of CaCO₃ and Mg(OH)₂ onto the sliding surfaces.     

Study on the tribological behavior of hybrid PTFE/cotton fabric composites filled with Sb2O3 and melamine cyanurate

The tribological behavior of the hybrid PTFE/cotton fabric composites filled with microsize Sb₂O₃ and melamine cyanurate (MCA) was investigated. It was found that the wear rate of the hybrid PTFE/cotton fabric composites decreased when Sb₂O₃ was used as the filler but increased with MCA filler. It was also observed that hybrid fillers (consists of Sb₂O₃ and MCA) had a wear reduction effect on the hybrid PTFE/cotton fabric composites at lower loads but increased the wear rate at higher loads. The wear behavior of the composites was explained in terms of the topography of worn surfaces and transfer film formed on the counterpart pin.     

Impact of Viscoelasticity on the Tribological Behavior of PTFE Composites for Valve Seals Application

In this article, we studied and explored the impact of viscoelasticity on the friction and wear behavior of pure polytetrafluoroethylene (PTFE), carbon–graphite PTFE composite, and glass fiber–MoS₂ PTFE composite. Tests were carried out using a specific reciprocating tribometer for valve seal application. The worn surfaces of the PTFE composites and the transfer films formed on the counterface were examined with a scanning electron microscope (SEM). Experimental results revealed that the addition of filler materials was effective in reducing the wear volume in all composites studied. In addition, the friction coefficient and wear resistance showed high sensitivity to the viscoelastic behavior of the PTFE seal. SEM investigation showed that the incorporation of particulate fillers into the PTFE matrix could dramatically reduce and stabilize the transfer films to the counterface, so they largely decreased the wear of the PTFE composites.     

Tribological behaviour of PTFE modified cotton polyester composites

Abstract

An attempt on modification of tribological behaviour of cotton polyester composite was done with polytetrafluoroethylene (PTFE). PTFE modified polyester–cotton composites were developed and studied for their friction and sliding wear behaviour at different applied loads. The sliding wear tests of composites were conducted against EN-31 steel counter face. The coefficient of friction μ as well as the sliding wear rate of cotton–polyester composites reduced significantly on addition of PTFE. The reduction in wear rate of PTFE modified polyester–cotton composite has been discussed with the help of SEM observations of worn surfaces and coefficient of friction.     

Tribological properties of spark-plasma-sintered ZrO2(Y2O3)-CaF2-Ag composites at elevated temperatures

Spark-plasma sintering is employed to synthesize self-lubricating ZrO₂(Y₂O₃) matrix composites with different additives of CaF₂ and Ag as solid lubricants by tailoring the composition and by adjusting the sintering temperature. The friction and wear behavior of ZrO₂(Y₂O₃) matrix composites have been investigated in dry sliding against an alumina ball from room temperature to 800 °C. The effective self-lubrication at different temperatures depends mainly on the content of various solid lubricants in the composites. The addition of 35 wt.% Ag and 30 wt.% CaF₂ in the ZrO₂(Y₂O₃) matrix can promote the formation of a well-covered lubricating film, and effectively reduce the friction and wear over the entire temperature range studied. The friction coefficients at low temperatures were at a minimum value for the composite containing 35 wt.% of silver. At this silver concentration, low and intermediate temperature lubricating properties are greatly improved without affecting high-temperature lubrication by the calcium fluoride in ZrO₂(Y₂O₃) matrix composites. The worn surfaces and transfer films formed during wear process have been characterized to identify the synergistic lubrication behavior of CaF₂ and Ag lubricants at different temperatures.     

Reduction in wear of metakaolinite-based geopolymer composite through filling of PTFE

Metakaolinite-based geopolymer composite containing 5-30% (volume fraction) polytetra-fluoroethylene (PTFE) was synthesized using compound activator composed of aqueous NaOH and sodium silicate at room temperature. Flexural strength, compressive strength and elastic modulus of the composite were measured. Tribological behaviour of the composite sliding against AISI-1045 steel was investigated on an MM-200 friction and wear tester. SEM, EDS and XPS analysis were conducted on worn surfaces and wear debris. The results show that mechanical strength of the composite was lower than corresponding geopolymer while the wear model became mild. The friction process was stable and the wear rate was dramatically reducted by 86-99.4%. The improvement of tribological properties of the composite was attributed to form a brown soft thin layer on the worn surface of the composite containing Fe₂O₃ came from tribochemical reaction. EDS analysis on the worn surfaces indicate the content of Fe increase along with the increase of volume content of PTFE in the composite. Furthermore, the counterpart, the steel ring was also protected from terrible wear as occurred when friction with geopolymer without any filling of solid lubricant. There is a brown thin layer mainly composed of Fe₂O₃ on the steel ring.     

Friction and Wear Behaviors of Several Polymers Sliding Against GCr15 and 316 Steel Under the Lubrication of Sea Water

Ocean tribology, a new research field of tribology, is currently being established and developed. The tribological behaviors of polyether ether ketone (PEEK), poly(phenyl p-hydroxybenzoate) (PHBA), polyimide (PI), and perfluoroethylene propylene copolymer (FEP) sliding against GCr15 and 316 steel rings under the lubrication of sea water were studied and compared with that under the lubrication of pure water. The results show that the friction and wear behaviors of a polymer under the lubrication of aqueous medium are not only related to the properties of polymer itself, but also to the corrosive effect and lubricating effect of the medium. When a polymer slid against GCr15 steel under sea water lubrication, the friction coefficient and wear rate of polymer were much larger than that under pure water lubrication because of indirect corrosive wear. However, when sliding against corrosion-resistant 316 steel, polymers PEEK, FEP, and PI exhibited lower coefficients of friction and wear rates under sea water lubrication, this was attributed to better lubricating effect of sea water as a result of the deposition of CaCO₃ and Mg(OH)₂ on the counterface. On the contrary, the friction coefficient and wear rate of PHBA sliding against 316 steel under sea water lubrication were larger than that under pure water lubrication, which may be related to the properties of PHBA itself.