The preparation of iron (III) oxide nanoparticles using W/O microemulsion

Iron (III) oxide, Fe₂O₃, nanoparticles were prepared using W/O microemulsion as the reactor. W/O microemulsion was formed using n-heptane as oil phase, water and AOT as the surfactant under the specific composition. Iron (III) Chloride was used as a starting material and Ammonium hydroxide was a precipitating agent. Fe₂O₃, nanoparticles were then produced in situ the water core. Size of particles could be adjusted by the water content of the mixtures. The higher the water content, the bigger the particle size. The average size of the nanoparticles obtained was smaller than 100 nm. Moreover, Fe₂O₃ produced by this method was hematite with hexagonal in structure.     

Functionalisation of Fe3 O4 nanoparticles by 2‐((pyrazol‐4‐yl) methylene) hydrazinecarbothioamide enhances the apoptosis of human breast cancer MCF‐7 cells

Cancer is a major cause of death. Thus, the incidence and mortality rate of cancer is globally important. Regarding vast problems caused by chemotherapy drugs, efforts have progressed to find new anti‐cancer drugs. Pyrazole derivatives are known as components with anti‐cancer properties. In here, Fe₃ O₄ nanoparticles were first functionalized with (3‐chloropropyl) trimethoxysilane, then 2‐((pyrazol‐4‐yl) methylene) hydrazinecarbothioamide (P) was anchored on the surface of magnetic nanoparticles (PL). The synthesized nano‐compounds were characterized using Fourier transform infrared spectroscopy, X‐ray diffraction, scanning electron microscopy, Zeta potential, dynamic light scattering, and energy‐dispersive x‐ray spectrometry analyses. The cytotoxicity effect was evaluated using MTT assay, apoptosis test by Flow cytometry, cell cycle analysis, Caspase‐3 activity assay and Hoechst staining on MCF‐7 cell line. The high toxicity for tumor cells and low toxicity on normal cells (MCF10A) was considered as an important feature (selectivity index, 10.9). Based on results, the IC50 for P and PL compounds were 157.80 and 131.84 μM/ml respectively. Moreover, apoptosis inducing, nuclear fragmentation, Caspase 3 activity and induction of cell rest in sub‐G1 and S phases, were also observed. The inhibitory effect of PL was significantly higher than P, which could be due to the high penetrability of Fe₃ O₄ nanoparticles.Inspec keywords: magnetic particles, drugs, nanomedicine, biochemistry, cancer, light scattering, scanning electron microscopy, molecular biophysics, iron compounds, electrokinetic effects, nanofabrication, tumours, X‐ray diffraction, cellular biophysics, nanoparticles, biomedical materials, toxicology, nanomagnetics, Fourier transform infrared spectra, enzymes, X‐ray chemical analysisOther keywords: anticancer properties, Fe₃ O₄ magnetic nanoparticles, (3‐chloropropyl) trimethoxysilane, energy‐dispersive X‐ray spectrometry, cell cycle analysis, MCF‐7 cell line, tumour cells, human breast cancer MCF‐7 cells, mortality rate, pyrazole derivatives, 2‐((pyrazol‐4‐yl) methylene) hydrazinecarbothioamide, chemotherapy drugs, heterocyclic components, nanocompounds, X‐ray diffraction, scanning electron microscopy, Zeta potential, dynamic light scattering, cytotoxicity effect, MTT assay, apoptosis test, caspase‐3 activity assay, Hoechst staining, MCF10A nontumourigenic cells, cell rest induction, nuclear fragmentation, Fe₃ O₄      

Biosynthesis of tin oxide (SnO2) nanoparticles using jujube fruit for photocatalytic degradation of organic dyes

In this study, tin oxide (SnO₂) nanoparticles were synthesized via a green route using jujube fruit as a non-toxic, renewable reducing agent, and excellent stabilizer. The biosynthesized SnO₂ nanoparticles were characterized by X-ray diffraction analysis (XRD), Fourier-Transform infrared (FT-IR), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). Moreover, the photocatalytic activity of the novel SnO₂ nanoparticles was investigated for degradation of two organic dyes which were named methylene blue (MB) and eriochrome black-T (EBT) under direct sunlight. An excellent performance was observed and about 90% and 83% of degradation efficiencies were achieved for MB and EBT, respectively. The high stability of the photocatalyst also makes SnO₂ nanoparticles easily to reuse at least four times without any remarkable loss in activity.     

Catalytic hydrolysis of cellobiose using different acid‐functionalised Fe3 O4 magnetic nanoparticles

The present study demonstrated the preparation of three different acid‐functionalised magnetic nanoparticles (MNPs) and evaluation for their catalytic efficacy in hydrolysis of cellobiose. Initially, iron oxide (Fe₃ O₄)MNPs were synthesised, which further modified by applying silica coating (Fe₃ O₄ ‐MNPs@Si) and functionalised with alkylsulfonic acid (Fe₃ O₄ ‐MNPs@Si@AS), butylcarboxylic acid (Fe₃ O₄ ‐MNPs@Si@BCOOH) and sulphonic acid (Fe₃ O₄ ‐MNPs@Si@SO₃ H) groups. The Fourier transform infrared analysis confirmed the presence of above‐mentioned acid functional groups on MNPs. Similarly, X‐ray diffraction pattern and energy dispersive X‐ray spectroscopy analysis confirmed the crystalline nature and elemental composition of MNPs, respectively. TEM micrographs showed the synthesis of spherical and polydispersed nanoparticles having diameter size in the range of 20–80 nm. Cellobiose hydrolysis was used as a model reaction to evaluate the catalytic efficacy of acid‐functionalised nanoparticles. A maximum 74.8% cellobiose conversion was reported in case of Fe₃ O₄ ‐MNPs@Si@SO₃ H in first cycle of hydrolysis. Moreover, thus used acid‐functionalised MNPs were magnetically separated and reused. In second cycle of hydrolysis, Fe₃ O₄ ‐MNPs@Si@SO₃ H showed 49.8% cellobiose conversion followed by Fe₃ O₄ ‐MNPs@Si@AS (45%) and Fe₃ O₄ ‐MNPs@Si@BCOOH (18.3%). However, similar pattern was reported in case of third cycle of hydrolysis. The proposed approach is considered as rapid and convenient. Moreover, reuse of acid‐functionalised MNPs makes the process economically viable.Inspec keywords: scanning electron microscopy, catalysis, magnetic separation, magnetic particles, silicon compounds, iron compounds, nanomagnetics, coatings, X‐ray chemical analysis, nanoparticles, X‐ray diffraction, nanofabrication, Fourier transform infrared spectra, organic compounds, nanocompositesOther keywords: catalytic efficacy, alkylsulfonic acid, butylcarboxylic acid, energy dispersive X‐ray spectroscopy analysis, spherical polydispersed nanoparticles, cellobiose hydrolysis, acid‐functionalised MNPs, acid functional groups, cellobiose conversion, acid‐functionalised magnetic nanoparticle, silica coating, sulphonic acid, Fourier transform infrared analysis, SEM micrograph, X‐ray diffraction pattern, size 20.0 nm to 80.0 nm, Fe₃ O₄ , Si, SiO₂      

Synthesis of monodisperse organic- and water-soluble iron oxide nanoparticles using Fe(OH)3 as precursor

The precursors used to prepare high-quality nanoparticles by high-temperature decomposition are expensive and toxic organometallic compounds. Fe(OH)₃, an inexpensive and environmentally friendly iron-containing compound, is for the first time introduced to act as an precursor to generate monodisperse iron oxide nanoparticles. The obtained nanoparticles are characterised by transmission electronic microscopy, IR, XRD and vibrating sample magnetometer. Organic-soluble ferromagnetic rod-like and superparamagnetic dot-like nanoparticles with the size ranging from 12 to 25?nm are obtained in a nonpolar solvent by adjusting reaction parameters, such as surfactant concentration and reaction time. Water-soluble nanoparticles can be synthesised when a bipolar solvent is used instead of nonpolar solvent. The results show that Fe(OH)₃ is a promising precursor for the high-temperature decomposition method.     

Photocatalytic degradation of azo dyes using Au:TiO2, gamma-Fe2O3:TiO2 functional nanosystems

We report photocatalytic degradation studies on Navy Blue HE2R (NB) dye on significant details as a representative from the class of azo dyes using functional nanosystems specifically designed to allow a strong photocatalytic activity. A modified sol-gel route was employed to synthesize Au and gamma-Fe2O3 modified TiO2 nanoparticles (NPs) at low temperature. The attachment strategy is better because it allows clear surface of TiO2 to remain open for photo-catalysis. X-ray diffraction, Raman and UV-VIS spectroscopy studies showed the presence of gold and iron oxide phases along-with the anatase TiO2 phase. TEM studies showed TiO2 nanocomposite particles of size approximately 10-12 nm. A detailed investigation on heterogeneous photocatalytic performance for Navy Blue HE2R dye was done using the as-synthesized catalysts Au:TiO2 and gamma-Fe2O3:TiO2 in aqueous suspension under 8 W low-pressure mercury vapour lamp irradiation. Also, the photocatalytic degradation of Amranth and Orange G azo dyes were studied. The surface modified TiO2 NPs showed significantly improved photocatalytic activity as compared to pure TiO2. Exposure of the dye to the UV light in the presence of pure and gold NPs attached TiO2 catalysts caused dye degradation of about approximately 20% and approximately 80%, respectively, in the first couple of hours. In the presence of gamma-Fe2O3 NPs attached TiO2, a remarkable approximately 95% degradation of the azo dye was observed only in the first 15 min of UV exposure. The process parameters for the optimum catalytic activity are established which lead to a complete decoloration and substantial dye degradation, supported by the values of the Chemical Oxygen Demand (COD) approximately 93% and Total Organic Carbon (TOC) approximately 65% of the treated dye solution after 5 hours on the employment of the UV/Au:TiO2/H2O2 photocatalytic process.     

A novel technique to prepare ultrafine Fe2O3 via hydrated iron(III) nitrate

Abstracts are not published in this journal This revised version was published online in November 2006 with corrections to the Cover Date.     

Antifungal and antiovarian cancer properties of α Fe2 O3 and α Fe2 O3 /ZnO nanostructures synthesised by Spirulina platensis

Candida albicans (C. albicans) infection shows a growing burden on human health, and it has become challenging to search for treatment. Therefore, this work focused on the antifungal activity, and cytotoxic effect of biosynthesised nanostructures on human ovarian tetracarcinoma cells PA1 and their corresponding mechanism of cell death. Herein, the authors fabricated advanced biosynthesis of uncoated α‐Fe₂ O₃ and coated α‐Fe₂ O₃ nanostructures by using the carbohydrate of Spirulina platensis. The physicochemical features of nanostructures were characterised by UV–visible, high resolution transmission electron microscopy, Fourier transform infrared spectroscopy, and X‐ray diffraction. The antifungal activity of these nanostructures against C. albicans was studied by the broth dilution method, and examined by 2′, 7′‐dichlorofluorescein diacetate staining. However, their cytotoxic effects against PA1 cell lines were evaluated by MTT and comet assays. Results indicated characteristic rod‐shaped nanostructures, and increasing the average size of α‐Fe₂ O₃ @ZnO nanocomposite (105.2 nm × 29.1 nm) to five times as compared to α‐Fe₂ O₃ nanoparticles (20.73nm × 5.25 nm). The surface coating of α‐Fe₂ O₃ by ZnO has increased its antifungal efficiency against C. albicans. Moreover, the MTT results revealed that α‐Fe₂ O₃ @ZnO nanocomposite reduces PA1 cell proliferation due to DNA fragmentation (IC₅₀ 18.5 μg/ml). Continual advances of green nanotechnology and promising findings of this study are in favour of using the construction of rod‐shaped nanostructures for therapeutic applications.Inspec keywords: nanocomposites, toxicology, nanofabrication, cellular biophysics, X‐ray diffraction, iron compounds, biochemistry, cancer, antibacterial activity, transmission electron microscopy, biomedical materials, wide band gap semiconductors, DNA, II‐VI semiconductors, visible spectra, molecular biophysics, ultraviolet spectra, nanomedicine, zinc compounds, nanoparticles, microorganisms, Fourier transform infrared spectraOther keywords: Spirulina platensis, antifungal activity, α‐Fe₂ O₃ nanoparticles, antiovarian cancer properties, Candida albicans infection, cytotoxic effect, biosynthesised nanostructures, human ovarian tetracarcinoma cell PA1, cell death, uncoated α‐Fe₂ O₃ , coated α‐Fe₂ O₃ nanostructures, α‐Fe₂ O₃ ‐ZnO nanocomposite, carbohydrate, physicochemical features, UV‐visible spectroscopy, high resolution transmission electron microscopy, Fourier transform infrared spectroscopy, X‐ray diffraction, broth dilution method, 2′, 7′‐dichlorofluorescein diacetate staining, PA1 cell lines, comet assays, MTT assays, rod‐shaped nanostructures, surface coating, PA1 cell proliferation, DNA fragmentation, green nanotechnology, Fe₂ O₃ ‐ZnO, Fe₂ O₃      

Size-dependent ultrafast magnetization dynamics in iron oxide (Fe3O4) nanocrystals

Optically induced ultrafast demagnetization and its recovery in superparamagnetic colloidal iron oxide (Fe3O4) nanocrystals have been investigated via time-resolved Faraday rotation measurements. Optical excitation with near-infrared laser pulse resulted in ultrafast demagnetization in approximately 100 fs via the destruction of ferrimagnetic ordering. The degree of demagnetization increased with the excitation density, and the complete demagnetization reached at approximately 10% excitation density. The magnetization recovered on two time scales, several picoseconds and hundreds of picoseconds, which can be associated with the initial reestablishment of the ferrimagnetic ordering and the electronic relaxation back to the ground state, respectively. The amplitude of the slower recovery component increased with the size of the nanocrystals, suggesting the size-dependent ferrimagnetic ordering throughout the volume of the nanocrystal.     

Antibacterial and dye degradation potential of zero‐valent silver nanoparticles synthesised using the leaf extract of Spondias dulcis

The present study reports a simple and low cost synthesis of zero‐valent silver nanoparticles (ZVSNPs) from silver nitrate using the leaf extract of Spondias dulcis. The ZVSNPs showed a unique peak at 420 nm in UV–vis spectrum. The SEM image portrayed cuboidal shaped particles. The EDX spectrum designated the elemental silver peak at 3 keV. In XRD, a sharp peak at 32.47° denoted the existence of (1 0 1) lattice plane and the average crystallite size was calculated as 48.61 nm. The lattice parameter was determined as 0.39 nm. The FTIR spectra of the leaf extract and ZVSNPs showed shifts in the specific functional group bands which ascertained the involvement of phytoconstituents in the formation and capping of nanoparticles. The average hydrodynamic size was measured as 59.66 nm by DLS method. A low PDI, 0.187 witnessed the monodispersity. A negative zeta potential value of −15.7 mV indicated the negative surface charges of the nanoparticles. The bactericidal action of ZVSNPs was demonstrated against two pathogens S.typhimurium and E.coli during which a dosage dependent zone of inhibition results was observed. Additionally, the catalytic potential of ZVSNPs was examined for the degradation of methylene blue dye in which an accelerated degradation of the dye was observed.Inspec keywords: antibacterial activity, crystallites, electrokinetic effects, scanning electron microscopy, nanoparticles, particle size, ultraviolet spectra, X‐ray chemical analysis, microorganisms, light scattering, nanofabrication, materials preparation, X‐ray diffraction, visible spectra, silver, dyes, Fourier transform infrared spectraOther keywords: wavelength 420.0 nm, Ag, voltage ‐15.7 mV, size 59.66 nm, size 0.39 nm, size 48.61 nm, electron volt energy 3.0 keV, Fourier transform infrared spectra, methylene blue dye, bactericidal action, dynamic light scattering, lattice parameter, Escherichia coli, Salmonella typhimurium, Spondias dulcis, negative zeta potential, polydispersity index, crystallite size, leaf extract, X‐ray diffraction, energy dispersive X‐ray spectrum, cuboidal‐shaped particles, scanning electron microscopy image, ultraviolet–visible spectrum, silver nitrate, zero‐valent silver nanoparticles     

Synthesis,characterisation and potential biomedical applications of magnetic core–shell structures: carbon‐, dextran‐, SiO2 ‐ and ZnO‐coated Fe3 O4 nanoparticles

Due to the strong effect of nanoparticles'' size and surface properties on cellular uptake and bio‐distribution, the selection of coating material for magnetic core–shell nanoparticles (CSNPs) is very important. In this study, the effects of four different biocompatible coating materials on the physical properties of Fe₃ O₄ (magnetite) nanoparticles (NPs) for different biomedical applications are investigated and compared. In this regard, magnetite NPs are prepared by a simple co‐precipitation method. Then, CSNPs including Fe₃ O₄ as a core and carbon, dextran, ZnO (zincite) and SiO₂ (silica) as different shells are synthesised using simple one‐ or two‐step methods. A comprehensive study is carried out on the prepared samples using X‐ray diffraction, vibrating sample magnetometry, transmission electron microscopy and Fourier transform infrared spectroscopy analyses. According to the authors'' findings, it is suggested that carbon‐ and dextran‐coated magnetite NPs with high M _s have great potential in the application of magnetic resonance imaging contrast agents. Moreover, silica‐coated magnetite NPs with high coercivity are potentially suitable candidates for hyperthermia and ZnO‐coated Fe₃ O₄ is potentially suitable for photothermal therapy.Inspec keywords: iron compounds, carbon, silicon compounds, zinc compounds, nanomedicine, biomedical materials, nanofabrication, nanoparticles, magnetic particles, coatings, X‐ray diffraction, magnetometry, transmission electron microscopy, Fourier transform spectra, infrared spectra, biomedical MRI, hyperthermia, radiation therapyOther keywords: biomedical applications, magnetic core‐shell nanoparticles, CSNP, cellular uptake, biodistribution, coating material, biocompatible coating materials, co‐precipitation, dextran, zincite, silica, X‐ray diffraction, vibrating sample magnetometry, transmission electron microscopy, Fourier transform infrared spectroscopy, magnetic resonance imaging contrast agents, hyperthermia, photothermal therapy, SiO₂ ‐Fe₃ O₄ , ZnO‐Fe₃ O₄      

Nanorods of iron oxalate synthesized using reverse micelles: facile route for alpha-Fe2O3 and Fe3O4 nanoparticles

Uniform and smooth nanorods of iron oxalate dihydrate have been synthesized using the reverse micellar route in the presence of the cationic surfactant CTAB (cetyltrimethyl ammonium bromide). These rods have an average diameter of 70 nm and length of 470 nm and show an antiferromagnetic ordering at 27 K. The oxalate rods act as suitable precursor for obtaining a variety of iron oxide nanoparticles depending on the nature of the atmosphere in which decomposition is performed. Spherical alpha-Fe2O3 nanoparticles (approximately 50 nm) were obtained when the nanorods were decomposed in air (500 degrees C) and show a transition from a weakly-ferromagnetic to weakly anti-ferromagnetic behaviour at approximately 225 K which is reminiscent of a Morin-like transition. Cuboidal Fe3O4 nanoparticles (approximately 60-70 nm) were obtained by the decomposition at 500 degrees C in vacuum (approximately 10(-5) torr) and show a Verwey transition at 122 K.     

Signal amplification strategy using gold/N ‐trimethyl chitosan/iron oxide magnetic composite nanoparticles as a tracer tag for high‐sensitive electrochemical detection

This study presents a novel signal amplification method for high‐sensitive electrochemical immunosensing. Gold (Au)/N ‐trimethyl chitosan (TMC)/iron oxide (Fe₃ O₄) (shell/shell/core) nanocomposite was used as a tracing tag to label antibody. The tag was shown to be capable of amplifying the recognition signal by high‐density assembly of Au nanoparticles (NPs) on TMC/Fe₃ O₄ particles. The remarkable conductivity of AuNPs provides a feasible pathway for electron transfer. The method was found to be simple, reliable and capable of high‐sensitive detection of human serum albumin as a model, down to 0.2 pg/ml in the range of 0.25–1000 pg/ml. Findings of the present study would create new opportunities for sensitive and rapid detection of various analytes.Inspec keywords: gold, filled polymers, conducting polymers, iron compounds, magnetic particles, nanoparticles, nanocomposites, nanosensors, electrochemical sensors, proteins, molecular biophysics, biomagnetism, biosensorsOther keywords: signal amplification strategy, gold‐N‐trimethyl chitosan‐iron oxide magnetic composite nanoparticles, tracer tag, high‐sensitive electrochemical detection, high‐sensitive electrochemical immunosensing, antibody, high‐density assembly, AuNP conductivity, electron transfer, human serum albumin, FeO‐Au     

Non-aqueous synthesis of water-dispersible Fe3O4-Ca3(PO4)2 core-shell nanoparticles

The Fe(3)O(4)-Ca(3)(PO(4))(2) core-shell nanoparticles were prepared by one-pot non-aqueous nanoemulsion with the assistance of a biocompatible triblock copolymer, poly(ethylene glycol)-block-poly(propylene glycol)-block-poly(ethylene glycol) (PEO-PPO-PEO), integrating the magnetic properties of Fe(3)O(4) and the bioactive functions of Ca(3)(PO(4))(2) into single entities. The Fe(3)O(4) nanoparticles were pre-formed first by thermal reduction of Fe(acac)(3) and then the Ca(3)(PO(4))(2) layer was coated by simultaneous deposition of Ca(2+) and PO(4)(3-). The characterization shows that the combination of the two materials into a core-shell nanostructure retains the magnetic properties and the Ca(3)(PO(4))(2) shell forms an hcp phase (a = 7.490 ?, c = 9.534 ?) on the Fe(3)O(4) surface. The magnetic hysteresis curves of the nanoparticles were further elucidated by the Langevin equation, giving an estimation of the effective magnetic dimension of the nanoparticles and reflecting the enhanced susceptibility response as a result of the surface covering. Fourier transform infrared (FTIR) analysis provides the characteristic vibrations of Ca(3)(PO(4))(2) and the presence of the polymer surfactant on the nanoparticle surface. Moreover, the nanoparticles could be directly transferred to water and the aqueous dispersion-collection process of the nanoparticles was demonstrated for application readiness of such core-shell nanostructures in an aqueous medium. Thus, the construction of Fe(3)O(4) and Ca(3)(PO(4))(2) in the core-shell nanostructure has conspicuously led to enhanced performance and multi-functionalities, offering various possible applications of the nanoparticles.     

In situ modifying of carbon tube-in-tube nanostructures with highly active Fe(2)O(3) nanoparticles

A novel in situ method based on a liquid membrane templated self-assembly process is employed to modify carbon tube-in-tube nanostructures (TTCNTs) with Fe(2)O(3) nanoparticles. The as-obtained Fe(2)O(3) modified TTCNTs (Fe(2)O(3)/TTCNTs) nanocomposites are well constructed and the Fe(2)O(3) nanoparticles are well dispersed and decorated on the outer, inner and intramolecular surfaces of TTCNTs. In addition, the Fe(2)O(3)/TTCNTs nanocomposites are employed as catalysts for selective catalytic reduction (SCR) of NO with NH(3) and show high SCR catalytic activity, indicating that the novel multiple intramolecular channels and unique surface chemistry of the TTCNTs should play an important role in improving the properties of?TTCNTs.     

Affinity capture of uropathogenic Escherichia coli using pigeon ovalbumin-bound Fe3O4@Al2O3 magnetic nanoparticles

Escherichia coli and Staphylococcus saprophyticus are the most common causes of urinary tract infections, with 80% of these infections caused by uropathogenic E. coli. Because the P fimbriae of E. coli have specificity toward Gal(alpha1-4)Gal beta units, pigeon ovalbumin (POA), whose structure contains terminal Gal(alpha1-4)Gal beta moieties, was used as a probe for interaction with P fimbriated E. coli. The functional affinity probes for these bacteria by immobilizing POA--a phosphoprotein--onto the surface of magnetic iron oxide nanoparticles (NPs) coated with alumina (Fe3O4@Al2O3), using the phosphate units of POA as linking groups for the formation of phosphate-alumina complexes. The immobilization process occurred within 30 s when performing the reaction under microwave heating. The magnetic POA-Fe3O4@Al2O3 NPs generated using this facile approach exhibited specificity toward P fimbriated E. coli. The bacteria targeted by the affinity probes were characterized by matrix-assisted laser desorption/ionization mass spectrometry. The detection limit toward uropathogenic bacteria when using this approach was approximately 9.60 x 10(4) cfu/mL (0.5 mL).