应用于DRM/DAB系统的高转换增益及线性度优化的新结构混频器

This paper focuses on a new design of a down-conversion mixer for a low-IF wideband receiver.Based on the folded structure and differential multiple gated transistor(DMGTR) technique,a novel quadrature mixer with a high conversion gain,a moderate linearity,and a moderate NF is proposed.The mixer is designed and implemented in a 0.18-m CMOS process,and can operate in a frequency range from 150 kHz to 1.5 GHz.The circuit performance is confirmed by both simulation and measurement results.The measurement results exhibit a peak conversion gain of 13.35 dB,a high third order input referred intercept point of 14.85 dBm,and a moderate single side band noise figure of 10.67 dB.Moreover,the whole quadrature mixer core occupies a compact die area of 0.122 mm2.It consumes a current of 3.96 mA(excluding the output buffers) under a single supply voltage of 1.8 V.     

Radio Frequency Low Noise Amplifier with Linearizing Bias Circuit

A 1.34 GHz-1=60 MHz low noise amplifier （LNA） designed in a 0.35 pm SiGe process is presented. The designed LNA exhibits a power gain of 21.46 dB and a noise figure （NF） of 1.27 dB at 1.34 GHz. The linearity is improved with an active biasing technique. The post-layout simulation shows an input referred 1-dB compression point （IPldn） of-11.52 dBm. Compared with the recent reported high gain LNAs, the proposed LNA has a much better linearity without degrading other performance. The LNA draws 10 mA current from a 3.3 V power supply.     

一种应用于GPS接收机的高线性度SiGe HBT低噪声放大器

A high linearity 1.575 GHz SiGe：HBT low noise amplifier （LNA） for global positioning system applications is described. The bipolar cascoded with an MOSFET LNA was fabricated in a commercial 0.18 μm SiGe BiCMOS process, A resistor bias feed circuit with a feedback resistor was designed for the LNA input transistor to improve its intermodulation and compression performance. The packaged chip tested on board has displayed a noise figure of 1. I 1 dB, a power gain of 18 dB, an output 1 dB compression point of ＋7.8 dBm and an input third-order intercept point of ＋1.8 dBm. The chip occupies a 500 × 560μm^2 area and consumes 3.6 mA from a 2.85 V power supply.     

Design of a low noise distributed amplifier with adjustable gain control in 0.15μm GaAs PHEMT

正A low noise distributed amplifier consisting of 9 gain cells is presented.The chip is fabricated with 0.15-μm GaAs pseudomorphic high electron mobility transistor(PHEMT) technology from Win Semiconductor of Taiwan.A special optional gate bias technique is introduced to allow an adjustable gain control range of 10 dB.A novel cascode structure is adopted to extend the output voltage and bandwidth.The measurement results show that the amplifier gives an average gain of 15 dB with a gain flatness of±1 dB in the 2-20 GHz band.The noise figure is between 2 and 4.1 dB during the band from 2 to 20 GHz.The amplifier also provides 13.8 dBm of output power at a 1 dB gain compression point and 10.5 dBm of input third order intercept point(IIP3),which demonstrates the excellent performance of linearity.The power consumption is 300 mW with a supply of 5 V,and the chip area is 2.36×1.01 mm~2.     

A wide band up-conversion mixer for cable television tuner

An up-conversion mixer implemented in a 0.35μm SiGe BiCMOS technology for a double conversion cable TV tuner is described, The mixer converts the 100MHz to 1000MHz band to the Intermediate Frequency of 1GHz above. The mixer meets the linearity and noise figure requirements for a TV tuner. The noise figure （IF） of 19.2-17.5dB, ldB compression of 12.1dBm, and gain of-1-0.7dB in the 900MHz band are achieved at a supply voltage of 5V. The power consumption is 47mW.     

Design and optimization of a 2.4 GHz RF front-end with an on-chip balun

A 2.4 GHz low-power,low-noise and highly linear receiver front-end with a low noise amplifier(LNA) and balun optimization is presented.Direct conversion architecture is employed for this front-end.The on-chip balun is designed for single-to-differential conversion between the LNA and the down-conversion mixer,and is optimized for the best noise performance of the front-end.The circuit is implemented with 0.35μm SiGe BiCMOS technology.The front-end has three gain steps for maximization of the input dynamic range.The overall maximum gain is about 36 dB.The double-sideband noise figure is 3.8 dB in high gain mode and the input referred third-order intercept point is 12.5 dBm in low gain mode.The down-conversion mixer has a tunable parallel R-C load at the output and an emitter follower is used as the output stage for testing purposes.The total front-end dissipation is 33 mW under a 2.85 V supply and occupies a 0.66 mm~2 die size.     

利用简单电阻偏置网络实现的高线性度电流驱动型无源混频器

A high linearity current communicating passive mixer including the mixing cell and transimpedance amplifier(TIA) is introduced.It employs the resistor in the TIA to reduce the source voltage and the gate voltage of the mixing cell.The optimum linearity and the maximum symmetric switching operation are obtained at the same time.The mixer is implemented in a 0.25μm CMOS process.The test shows that it achieves an input third-order intercept point of 13.32 dBm,conversion gain of 5.52 dB,and a single sideband noise figure of 20 dB.     

A 50 MHz-1 GHz high linearity CATV amplifier with a 0.15μm InGaAs PHEMT process

A 50 MHz-1 GHz low noise and high linearity amplifier monolithic-microwave integrated-circuit (MMIC) for cable TV is presented.A shunt AC voltage negative feedback combined with source current negative feedback is adopted to extend the bandwidth and linearity.A novel DC bias feedback is introduced to stabilize the operation point,which improved the linearity further.The circuit was fabricated with a 0.15μm InGaAs PHEMT (pseudomorphic high electron mobility transistor) process.The test was carried out in 75Ωsystems from 50 MHz to 1 GHz.The measurement results showed that it gave a small signal gain of 16.5 dB with little gain ripples of less than±1dB.An excellent noise figure of 1.7-2.9 dB is obtained in the designed band.The IIP3 is 16 dBm, which shows very good linearity.The CSO and CTB are high up to 68 dBc and 77 dBc,respectively.The chip area is 0.56 mm~2 and the power dissipation is 110 mA with a 5 V supply.It is ideally suited to cable TV systems.     

A 0.18μm CMOS low noise amplifier using a current reuse technique for 3.1-10.6 GHz UWB receivers

A new,low complexity,ultra-wideband 3.1-10.6 GHz low noise amplifier(LNA),designed in a chartered 0.18μm RFCMOS technology,is presented.The ultra-wideband LNA consists of only two simple amplifiers with an inter-stage inductor connected.The first stage utilizing a resistive current reuse and dual inductive degeneration technique is used to attain a wideband input matching and low noise figure.A common source amplifier with an inductive peaking technique as the second stage achieves high flat gain and wide -3 dB bandwidth of the overall amplifier simultaneously.The implemented ultra-wideband LNA presents a maximum power gain of 15.6 dB,and a high reverse isolation of—45 dB,and good input/output return losses are better than -10 dB in the frequency range of 3.1-10.6 GHz.An excellent noise figure(NF) of 2.8-4.7 dB was obtained in the required band with a power dissipation of 14.1 mW under a supply voltage of 1.5 V.An input-referred third-order intercept point(IIP3) is -7.1 dBm at 6 GHz.The chip area,including testing pads,is only 0.8×0.9 mm2.     

用于U波段移动数字电视的宽带大动态范围高线性度射频前端

A wideband large dynamic range and high linearity U-band RF front-end for mobile DTV is introduced,and includes a noise-cancelling low-noise amplifier(LNA),an RF programmable gain amplifier(RFPGA) and a current communicating passive mixer.The noise/distortion cancelling structure and RC post-distortion compensation are employed to improve the linearity of the LNA.An RFPGA with five stages provides large dynamic range and fine gain resolution.A simple resistor voltage network in the passive mixer decreases the gate bias voltage of the mixing transistor,and optimum linearity and symmetrical mixing is obtained at the same time.The RF front-end is implemented in a 0.25 μm CMOS process.Tests show that it achieves an ⅡP3(third-order intercept point) of –17 dBm,a conversion gain of 39 dB,and a noise figure of 5.8 dB.The RFPGA achieves a dynamic range of –36.2 to 23.5 dB with a resolution of 0.32 dB.     

Design and optimization of CMOS LNA with ESD protection for 2.4 GHz WSN application

A new optimization method of a source inductive degenerated low noise amplifier(LNA) with electrostatic discharge protection is proposed.It can achieve power-constrained simultaneous noise and input matching. An analysis of the input impedance and the noise parameters is also given.Based on the developed method,a 2.4 GHz LNA for wireless sensor network application is designed and optimized using 0.18-μm RF CMOS technology. The measured results show that the LNA achieves a noise figure of 1.59 dB,a power gain of 14.12 dB, an input 1 dB compression point of-8 dBm and an input third-order intercept point of 1 dBm.The DC current is 4 mA under a supply of 1.8 V.     

An RF front-end with an automatic gain control technique for a U/V band CMMB receiver

This paper presents a fully integrated RF front-end with an automatic gain control(AGC) scheme and a digitally controlled radio frequency varied gain amplifier(RFVGA) for a U/V band China Mobile Multimedia Broadcasting(CMMB) direct conversion receiver.The RFVGA provides a gain range of 50 dB with a 1.6 dB step. The adopted AGC strategy could improve immunity to adjacent channel signal,which is of importance for CMMB application.The front-end,composed of a low noise amplifier(LNA),an RFVGA,a mixer and AGC,achieves an input referred 3rd order intercept point(IIP3) of 4.9 dBm with the LNA in low gain mode and the RFVGA in medium gain mode,and a less than 4 dB double side band noise figure with both the LNA and the RFVGA in high gain mode.The proposed RF front-end is fabricated in a 0.35μm SiGe BiCMOS technology and consumes 25.6 mA from a 3.0 V power supply.     

A wideband current-commutating passive mixer for multi-standard receivers in a 0.18 μm CMOS

This paper reports a wideband passive mixer for direct conversion multi-standard receivers.A brief comparison between current-commutating passive mixers and active mixers is presented.The effect of source and load impedance on the linearity of a mixer is analyzed.Specially,the impact of the input impedance of the transimpedance amplifier(TIA),which acts as the load impedance of a mixer,is investigated in detail.The analysis is verified by a passive mixer implemented with 0.18 m CMOS technology.The circuit is inductorless and can operate over a broad frequency range.On wafer measurements show that,with radio frequency(RF) ranges from 700 MHz to 2.3 GHz,the mixer achieves 21 dB of conversion voltage gain with a-1 dB intermediate frequency(IF) bandwidth of 10 MHz.The measured IIP3 is 9 dBm and the measured double-sideband noise figure(NF) is 10.6 dB at 10 MHz output.The chip occupies an area of 0.19 mm2 and drains a current of 5.5 mA from a 1.8 V supply.     

A Fully Integrated 60GHz Four Channel CMOS Receiver with 7GHz Ultra-Wide Bandwidth for IEEE 802.11ad Standard

In this paper, a fully integrated CMOS receiver frontend for high-speed short range wireless applications centering at 60GHz millimeter wave （mmW） band is designed and implemented in 90nm CMOS technology. The 60GHz receiver is designed based on the super-heterodyne architecture consisting of a low noise amplifier （LNA） with inter-stage peaking technique, a single- balanced RF mixer, an IF amplifier, and a double-balanced I/Q down-conversion IF mixer. The proposed 60GHz receiver frontend derives from the sliding-IF structure and is designed with 7GHz ultra-wide bandwidth around 60GHz, supporting four 2.16GHz receiving channels from IEEE 802.1lad standard for next generation high speed Wi- Fi applications. Measured results show that the entire receiver achieves a peak gain of 12dB and an input 1-dB compression point of -14.SdBm, with a noise figure of lower than 7dB, while consumes a total DC current of only 60mA from a 1.2V voltage supply.     

A 0.18μm CMOS gain-switched LNA and mixer with large dynamic range

A 2.4GHz 0.18μm CMOS gain-switched single-end Low Noise Amplifier （LNA） and a passive mixer with no external balun for near-zero-IF （Intermediate Frequency）/RF （Radio Frequency） applications are described. The LNA, fabricated in the 0.18μm 1P6M CMOS technology, adopts a gain-switched technique to increase the linearity and enlarge the dynamic range. The mixer is an IQ-based passive topology. Measurements of the CMOS chip are performed on the FR-4 PCB and the input is matched to 50Ω. Combining LNA and mixer, the front-end measured performances in high gain state are： -15dB of Sll, 18.5dB of voltage gain, 4.6dB of noise figure, 15dBm of IIP3, 85dBm to -10dBm dynamic range. The full circuit drains 6mA from a 1.8V supply.     

A RF receiver frontend for SC-UWB in a 0.18-μm CMOS process

正A radio frequency(RF) receiver frontend for single-carrier ultra-wideband(SC-UWB) is presented. The front end employs direct-conversion architecture,and consists of a differential low noise amplifier(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The proposed LNA employs source inductively degenerated topology.First,the expression of input impedance matching bandwidth in terms of gate-source capacitance, resonant frequency and target S_(11) is given.Then,a noise figure optimization strategy under gain and power constraints is proposed,with consideration of the integrated gate inductor,the bond-wire inductance,and its variation.The LNA utilizes two stages with different resonant frequencies to acquire flat gain over the 7.1-8.1 GHz frequency band,and has two gain modes to obtain a higher receiver dynamic range.The mixer uses a double balanced Gilbert structure.The front end is fabricated in a TSMC 0.18-/im RF CMOS process and occupies an area of 1.43 mm~2.In high and low gain modes,the measured maximum conversion gain are 42 dB and 22 dB,input 1 dB compression points are -40 dBm and -20 dBm,and S_(11) is better than -18 dB and -14.5 dB.The 3 dB IF bandwidth is more than 500 MHz.The double sideband noise figure is 4.7 dB in high gain mode.The total power consumption is 65 mW from a 1.8 V supply.     

应用于2.4GHz无线传感网的超低功耗射频接收前端设计

This paper presents the design of an ultralow power receiver front-end designed for a wireless sensor network （WSN） in a 0.18 μm CMOS process. The author designs two front-ends working in the saturation region and the subthreshold region respectively. The front-ends contain a two-stage cross-coupling cascaded common-gate （CG） LNA and a quadrature Gilbert IQ mixer. The measured conversion gain is variable with high gain at 24 dB and low gain at 7 dB for the saturation one, and high gain at 22 dB and low gain at 5 dB for the subthreshold one. The noise figure （NF） at high gain mode is 5.1 dB and 6.3 dB for each. The input 1 dB compression point （IPldB） at low gain mode is about -6 dBm and -3 dBm for each. The front-ends consume about 2.1 mA current from 1.8 V power supply for the saturation one and 1.3 mA current for the subthreshold one. The measured results show that, comparing with the power consumption saving, it is worth making sacrifices on the performance for using the subthreshold technology.     

A reconfigurable passive mixer for multimode multistandard receivers in 0.18 μm CMOS

This paper presents a reconfigurable quadrature passive mixer for multimode multistandard receivers. By using controllable transconductor and transimpedance-amplifier stages, the voltage conversion gain of the mixer is reconfigured according to the requirement of the selected communication standard Other characteristics such as noises figure, linearity and power consumption are also reconfigured consequently. The design concept is verified by implementing a quadrature passive mixer in 0.18 μm CMOS technology. On wafer measurement results show that, with the input radio frequency ranges from 700 MHz to 2.3 GHz, the mixer achieves a controllable voltage conversion gain from 4 to 22 dB with a step size of 6 dB. The measured maximum ⅡP3 is 8.5 dBm and the minimum noise figure is 8.0 dB. The consumed current for a single branch (I or Q) ranges from 3.1 to 5.6 mA from a 1.8 V supply voltage. The chip occupies an area of 0.71 mm² including pads.     

一种电流复用共栅低噪声放大器的低功耗433/915-MHz射频前端的设计

This paper presents a wideband RF front-end with novel current-reuse wide band low noise amplifier(LNA),current-reuse V –I converter,active double balanced mixer and transimpedance amplifier for short range device(SRD) applications.With the proposed current-reuse LNA,the DC consumption of the front-end reduces considerably while maintaining sufficient performance needed by SRD devices.The RF front-end was fabricated in 0.18 μm RFCMOS process and occupies a silicon area of just 0.11 mm2.Operating in 433 MHz band,the measurement results show the RF front-end achieves a conversion gain of 29.7 dB,a double side band noise figure of 9.7 dB,an input referenced third intercept point of –24.9 dBm with only 1.44 mA power consumption from 1.8 V supply.Compared to other reported front-ends,it has an advantage in power consumption.     

A wideband CMOS VGLNA based on single-to-differential stage and resistive attenuator for TV tuners

A wideband CMOS variable gain low noise amplifier(VGLNA) based on a single-to-differential(S2D) stage and resistive attenuator is presented for TV tuner applications.Detailed analysis of input matching,noise figure(NF) and linearity for S2D is given.A highly linear passive resistive attenuator is proposed to provide 6 dB attenuation and input matching for each gain stage.The chip was fabricated by a 0.18μm 1P6M CMOS process, and the measurements show that the VGLNA covers a gain range over 36.4 dB and achieves a maximum gain of 21.3 dB,a minimum NF of 3.0 dB,an IIP3 of 0.9 dBm and an IIP2 of 26.3 dBm at high gain mode with a power consumption less than 10 mA from a 1.8 V supply.