Plasma characterization of the superconducting proton linear accelerator plasma generator using a 2 MHz compensated Langmuir probe

The CERN study for a superconducting proton Linac (SPL) investigates the design of a pulsed 5 GeV Linac operating at 50 Hz. As a first step towards a future SPL H(-) volume ion source, a plasma generator capable of operating at Linac4 or nominal SPL settings has been developed and operated at a dedicated test stand. The hydrogen plasma is heated by an inductively coupled RF discharge e(-) and ions are confined by a magnetic multipole cusp field similar to the currently commissioned Linac4 H(-) ion source. Time-resolved measurements of the plasma potential, temperature, and electron energy distribution function obtained by means of a RF compensated Langmuir probe along the axis of the plasma generator are presented. The influence of the main tuning parameters, such as RF power and frequency and the timing scheme is discussed with the aim to correlate them to optimum H(-) ion beam parameters measured on an ion source test stand. The effects of hydrogen injection settings which allow operation at 50 Hz repetition rate are discussed.     

Decrease in the ignition pressure of anomalous glow discharge in a magnetron with an ion-beam-irradiated cathode

The influence of an ion beam injected along the axis of the anode electrode of a planar magnetron on the initiation of an anomalous low-pressure glow discharge in a magnetron has been considered. The characteristics of the discharge ignition at pressures <8 × 10^?2 Pa and the properties of a planar magnetron with an ion-beam-irradiated cathode are determined. It is established that the discharge ignition voltage decreases with an increase in the ion energy and exhibits a threshold behavior as a function of the ion-beam current. It is shown that there is a prospect for extending the functional capabilities of planar magnetrons through matching of the modes of sputtering of the magnetron anode and cathode by an ion beam and plasma ions of an anomalous glow discharge, respectively.     

A source of gas, vapor, metal, and carbon ions based on a low-pressure hollow-cathode discharge

A compact source of gas, vapor, metal, and carbon ions based on a cold-hollow-cathode reflective discharge has been developed, in which a 6-mm-diameter flat target (Cu, Mo, W, C) is installed on the bottom of the cold cathode insulated from it. The density of the ion flow from cathode plasma reaches 100 mA/cm² at an accelerating voltage of up to 10 kV and a discharge current of 0.2-0.5 A. Vapors produced during ion sputtering of the target are ionized in the cathode and anode cavities. A beam containing ions of the plasma-producing gas and vapor is extracted throug h the channel in the reflector cathode. A fraction of the vapor of the sputtered target, the flow of which is sufficient for growing layers at a rate of ∼0.03 nm/s at a distance of 10 cm from the emission channel under the action of an ion beam, is extracted together with ions. The fraction of metal ions in the extracted beam is 0.05-0.10. The total current of the ion beam is 20-30 mA.     

Optical emission spectroscopy of the Linac4 and superconducting proton Linac plasma generators

CERN's superconducting proton Linac (SPL) study investigates a 50 Hz high-energy, high-power Linac for H(-) ions. The SPL plasma generator is an evolution of the DESY ion source plasma generator currently operated at CERN's Linac4 test stand. The plasma generator is a step towards a particle source for the SPL, it is designed to handle 100 kW peak RF-power at a 6% duty factor. While the acquisition of an integrated hydrogen plasma optical spectrum is straightforward, the measurement of a time-resolved spectrum requires dedicated amplification schemes. The experimental setup for visible light based on photomultipliers and narrow bandwidth filters and the UV spectrometer setup are described. The H(α), H(β), and H(γ) Balmer line intensities, the Lyman band and alpha transition were measured. A parametric study of the optical emission from the Linac4 ion source and the SPL plasma generator as a function of RF-power and gas pressure is presented. The potential of optical emission spectrometry coupled to RF-power coupling measurements for on-line monitoring of short RF heated hydrogen plasma pulses is discussed.     

Hollow target magnetron-sputter-type solid material ion source

A thin-walled aluminum (Al) hollow electrode has been inserted into an ion source to serve as an electrode for a radio frequency magnetron discharge. The produced plasma stabilized by argon (Ar) gas sputters the Al electrode to form a beam of Al(+) and Ar(+) ions. The total beam current extracted through a 3 mm diameter extraction hole has been 50 μA, with the Al(+) ion beam occupying 30% of the total beam current.     

Sheath structure in negative ion sources for fusion (invited)

In fusion negative ion sources, the negative ions are formed on the caesiated plasma grid predominantly by hydrogen atoms from the plasma. The space charge of the negative ions leaving the wall is not fully compensated by incoming positive ions and at high enough emission a virtual cathode is formed. This virtual cathode limits the flux of negative ions transported across the sheath to the plasma. A 1D collisionless model of the sheath is presented taking into account the virtual cathode. The model will be applied to examples of the ion source operation. Extension of the model to the bulk plasma shows good agreement with experimental data. A possible role for fast ions is discussed.     

Gas discharge ion source. II. Duopigatron

Ion source performance characteristics consisting of total ion current, ion energy distribution, mass distribution, and ion current density distribution have been measured for several models of a duopigatron. Variations on the duopigatron design involved plasma expansion cup material and dimensions, secondary cathode material, and interelectrode spacings. Of the designs tested, the one with a copper and molybdenum secondary cathode, and a mild steel plasma expansion cup proved to give the best results. The ion current density distribution was peaked at the center of the plasma expansion cup and fell off to 80% of the peak value at the cup wall for a cup 15.2 mm deep. A total ion current of 180 mA consisting of 60%-70% atomic ions was produced with an arc current of 20 A and source pressure of 9.3 Pa. More shallow cups produced a larger beam current and a more sharply peaked ion current density distribution. Typical ion energy distributions were bellshaped curves with a peak 10-20 V below anode potential and with ion energies extending 30-40 V on either side of the peak.     

A source of broad homogeneous beams of low-energy (∼0.5 keV) gas ions

A source of gas ions (argon, oxygen, nitrogen, etc.), the operating principle of which is based on the use of a glow discharge in an electrode system of a wide-aperture hollow cathode and anode in a magnetic field, is described. The exit aperture diameter of the hollow cathode, increased up to a size close to the ion beam diameter (10 cm), ensures the uniform ion emission of the plasma generated in the discharge region near the anode. A decreased angular divergence or increased ultimate ion-beam current density is achieved by a change in the potential drop in the space charge sheath between the plasma and the ion optics. The source generates broad (50 cm²) slightly diverging (ω/2∼3°–5°) ion beams with energies of 300–1000 eV at a beam current density of ∼0.5 mA/cm².     

Numerical analysis of surface produced H- ions by using two-dimensional particle-in-cell method

The modeling and analysis of a negative ion source is proceeding by using a 2D particle-in-cell simulation. The effect of the H(-) ion production on the plasma grid (PG) surface is investigated. It is shown that with the increase of H(-) ions per time step, the H(-) ion current density is enhanced, while the electron current density decreases with increasing the H(-) production rate on the PG surface. These results agree well with the experimental results observed in typical negative ion sources. Moreover, it is found that plasma quasi-neutrality is held mainly by both H(+) and H(-) ions in the bulk plasma around the PG.     

A source of broad electron beams with a self-heated hollow cathode for plasma nitriding of stainless steel

The principle of operation and characteristics of a broad electron beam source based on the discharge with a self-heated hollow cathode and widened anode part are described. The source is intended for the ion nitriding of metals in the electron beam plasma. The influence of the current density (1–7 mA/cm²) and ion energy (0.1–0.3 keV) on the nitriding rate of the 12X18H10T austenitic stainless steel is studied. It is shown that the maximal nitriding rate is reached by the combining of the minimal bias voltage across the samples (100 V) and maximal ion current density, which ensures the dynamic oxide layer sputtering on the sample surface. The electron source, in which electrons are extracted through a stabilizing grid in the direction normal to the axis of the hollow cathode, ensures the radially divergent electron beam formation with a 700-cm² initial cross section, a current of up to 30 A, and initial electron energy of 0.1–0.5 keV. The source stably operates at nitrogen-argon mixture pressures of up to 3 Pa.     

Simple Penning ion source for laboratory research and development applications

A simple Penning ion generator (PIG) that can be easily fabricated with simple machining skills and standard laboratory accessories is described. The PIG source uses an iron cathode body, samarium cobalt permanent magnet, stainless steel anode, and iron cathode faceplate to generate a plasma discharge that yields a continuous 1 mA beam of positively charged hydrogen ions at 1 mTorr of pressure. This operating condition requires 5.4 kV and 32.4 W of power. Operation with helium is similar to hydrogen. The ion source is being designed and investigated for use in a sealed-tube neutron generator; however, this ion source is thoroughly described so that it can be easily implemented by other researchers for other laboratory research and development applications.     

Analysis of the H- ion emissive surface in the extraction region of negative ion sources

To understand the plasma characteristics in the extraction region of negative H(-) sources is very important for the optimization of H(-) extraction from the sources. The profile of plasma density and electrostatic potential in the extraction region with and without extraction grid voltage are analyzed with a 2D particle in cell modeling of the NIFS-RD H(-) sources. The simulation results make clear the physical process forming a double ion plasma layer (which consists only of positive H(+) and negative H(-) ions) recently observed in the Cs-seeded experiments of the NIFS-R&D source in the vicinity of the extraction hole and the plasma grid. The results also give a useful insight into the formation mechanism of the plasma meniscus and the H(-) extraction process for such double ion plasma.     

Broad beam sources of fast molecules with segmented cold cathodes and emissive grids

Experimental study of fast neutral atom and molecule beam sources with rectangular and circular cross-section of the beam up to 0.8 m² is carried out and the study results are presented. The fast particles are produced as a result of charge exchange collisions between gas molecules and ions accelerated by potential drop between the plasma emitter of the beam source and the secondary plasma inside the processing vacuum chamber. As the emitter is used a glow discharge plasma, whose electrons are confined in an electrostatic trap formed by a cold hollow cathode and an emissive grid, which is negative both to the cathode and to the chamber. In order to prevent from breakdowns between the emitter and the cathode at a current in the cathode circuit up to 10 A as well as between the emitter and the grid at a voltage between them up to 10 kV the cathode and the grid are composed of isolated from each other segments, which are connected to power supplies through resistors. When resistance of the resistorR > U/I ₀, where U is the power supply voltage and I ₀ is the minimal current of stable vacuum arc for a given segment material, then transition from the glow discharge to the steady-state vacuum arc is totally excluded in spite of numerous breakdowns of microsecond duration due to contamination of the source electrodes during its operation with dielectric films and other stimulants of the arc.     

Arc discharge regulation of a megawatt hot cathode bucket ion source for the experimental advanced superconducting tokamak neutral beam injector

Arc discharge of a hot cathode bucket ion source tends to be unstable what attributes to the filament self-heating and energetic electrons backstreaming from the accelerator. A regulation method, which based on the ion density measurement by a Langmuir probe, is employed for stable arc discharge operation and long pulse ion beam generation. Long pulse arc discharge of 100 s is obtained based on this regulation method of arc power. It establishes a foundation for the long pulse arc discharge of a megawatt ion source, which will be utilized a high power neutral beam injection device.     

A new extraction system for the Linac4 H- ion source

As part of the CERN accelerator complex upgrade, a new linear accelerator for H(-) (Linac4) is under construction. The ion source design is based on the non-caesiated DESY RF-driven ion source, with the goal of producing an H(-) beam of 80 mA beam current, 45 keV beam energy, 0.4 ms pulse length, and 2 Hz repetition rate. The source has been successfully commissioned for an extraction voltage of 35 kV, corresponding to the one used at DESY. Increasing the extraction voltage to 45 kV has resulted in frequent high voltage breakdowns in the extraction region caused by evaporating material from the electron dump, triggering a new design of the extraction and electron dumping system. Results of the ion source commissioning at 35 kV are presented as well as simulations of a new pulsed extraction system for beam extraction at 45 kV.     

Fast ion beam-plasma interaction system

A device has been constructed for the study of the interaction between a fast ion beam and a target plasma of separately controllable parameters. The beam of either hydrogen or helium ions has an energy of 1-4 keV and a total current of 0.5-2 A. The beam energy and beam current can be varied separately. The ion source plasma is created by a pulsed (0.2-10-ms pulse length) discharge in neutral gas at up to 3 x 10(-3) Torr. The neutrals are pulsed into the source chamber, allowing the neutral pressure in the target region to remain less than 5 x 10(-5) Torr at a 2-Hz repetition rate. The creation of the source plasma can be described by a simple set of equations which predict optimum source design parameters. The target plasma is also produced by a pulsed discharge. Between the target and source chambers the beam is neutralized by electrons drawn from a set of hot filaments. Currently under study is an unstable wave in a field-free plasma excited when the beam velocity is nearly equal to the target electron thermal velocity (v(beam) approximately 3.5 x 10(7) cm/s, Te = 0.5 eV).     

New ion source for KSTAR neutral beam injection system

The neutral beam injection system (NBI-1) of the KSTAR tokamak can accommodate three ion sources; however, it is currently equipped with only one prototype ion source. In the 2010 and 2011 KSTAR campaigns, this ion source supplied deuterium neutral beam power of 0.7-1.6 MW to the KSTAR plasma with a beam energy of 70-100 keV. A new ion source will be prepared for the 2012 KSTAR campaign with a much advanced performance compared with the previous one. The newly designed ion source has a very large transparency (～56%) without deteriorating the beam optics, which is designed to deliver a 2 MW injection power of deuterium beams at 100 keV. The plasma generator of the ion source is of a horizontally cusped bucket type, and the whole inner wall, except the cathode filaments and plasma grid side, functions as an anode. The accelerator assembly consists of four multi-circular aperture grids made of copper and four electrode flanges made of aluminum alloy. The electrodes are insulated using PEEK. The ion source will be completed and tested in 2011.     

The development of the radio frequency driven negative ion source for neutral beam injectors (invited)

Large and powerful negative hydrogen ion sources are required for the neutral beam injection (NBI) systems of future fusion devices. Simplicity and maintenance-free operation favors RF sources, which are developed intensively at the Max-Planck-Institut fu?r Plasmaphysik (IPP) since many years. The negative hydrogen ions are generated by caesium-enhanced surface conversion of atoms and positive ions on the plasma grid surface. With a small scale prototype the required high ion current density and the low fraction of co-extracted electrons at low pressure as well as stable pulses up to 1 h could be demonstrated. The modular design allows extension to large source dimensions. This has led to the decision to choose RF sources for the NBI of the international fusion reactor, ITER. As an intermediate step towards the full size ITER source at IPP, the development will be continued with a half-size source on the new ELISE testbed. This will enable to gain experience for the first time with negative hydrogen ion beams from RF sources of these dimensions.     

Characteristics of low-energy ion beams extracted from a wire electrode geometry

Beams of argon ions with energies less than 50 eV were extracted from an ion source through a wire electrode extractor geometry. A retarding potential energy analyzer (RPEA) was constructed in order to characterize the extracted ion beams. The single aperture RPEA was used to determine the ion energy distribution function, the mean ion energy and the ion beam energy spread. The multi-cusp hot cathode ion source was capable of producing a low electron temperature gas discharge to form quiescent plasmas from which ion beam energy as low as 5 eV was realized. At 50 V extraction potential and 0.1 A discharge current, the ion beam current density was around 0.37 mA/cm(2) with an energy spread of 3.6 V or 6.5% of the mean ion energy. The maximum ion beam current density extracted from the source was 0.57 mA/cm(2) for a 50 eV ion beam and 1.78 mA/cm(2) for a 100 eV ion beam.     

Features of semiplanotron surface plasma sources

Features of the semiplanotron surface plasma sources (SPS) with cesiation used for high efficient negative ion beam production from first development to modern condition are considered. Design features of semiplanotrons SPS with cylindrical and spherical geometric focusing and the features of the negative ion production in the semiplanotrons are reviewed. Several versions of semiplanotrons with efficiency up to 0.1 A of H(-) per kW of discharge power are discussed. Modifications of the semiplanotrons for dc operation and for heavy negative ion production are reviewed.