Variation of non‐isothermal crystallization behavior of isotactic polypropylene with varying β‐nucleating agent content

The non‐isothermal crystallization behavior, the crystallization kinetics, the crystallization activation energy and the morphology of isotactic polypropylene (iPP) with varying content of β‐nucleating agent were investigated using differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). The DSC results showed that the Avrami equation modified by Jeziorny and a method developed by Mo and co‐workers could be successfully used to describe the non‐isothermal crystallization process of the nucleated iPPs. The values of n showed that the non‐isothermal crystallization of α‐ and β‐nucleated iPPs corresponded to a tridimensional growth with homogeneous and heterogeneous nucleation, respectively. The values of crystallization rate constant showed that the rate of crystallization decreased for iPPs with the addition of β‐nucleating agent. The crystallization activation energy increased with a small amount (less than 0.1 wt%) of β‐nucleating agent and decreased with higher concentration (more than 0.1 wt%). The changes of crystallization rate, crystallization time and crystallization activation energy of iPPs with varying contents of β‐nucleating agent were mainly determined by the ratio of the content of α‐ and β‐phase in iPP (α‐PP and β‐PP) from the DSC investigation, and the large size and many intercrossing lamellae between boundaries of β‐spherulites for iPPs with small amounts of β‐nucleating agent and the small size and few intercrossing bands among the boundaries of β‐spherulites for iPPs with large amounts of β‐nucleating agent from the SEM examination. Copyright © 2010 Society of Chemical Industry     

The formation of β‐polypropylene crystals in a compatibilized blend of isotactic polypropylene and polyamide‐6

Compatibilized polypropylene (PP)/polyamide (PA6) blends with and without β nucleating agent (β‐NA) are prepared, and are designated as Blend‐0.3 and Blend‐0, respectively. The melting and crystallization characteristic of the blends crystallized under different cooling rates and different crystallization temperatures are studied. It is observed that high β‐PP content can be developed in Blend‐0.3 only at slow cooling rates (<5°C/min), whereas high α‐PP content is formed at fast cooling rates. Isothermal crystallization analysis of Blend‐0 indicates that PA6 is an effective NA for α‐PP in the lower temperature range, whereas the α‐nucleating effect disappears in the higher temperature range. Blend‐0.3 can, therefore, be viewed as a system containing both α‐ and β‐NAs, simultaneously. PA6 is competing with β‐NA in inducing PP crystallization. Under the normal injection of Blend‐0.3, the melt will be cooled through the higher temperature that favors the effectiveness of β‐NA rapidly because of the faster cooling rate. However, the α‐nucleation effect from PA6 predominate at the lower temperature. This explains the difficulty in obtaining high β‐PP content in Blend‐0.3 from injection molding. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers     

Melting and crystallization behaviors,morphology, and mechanical properties of β‐polypropylene/polypropylene‐graft‐maleic anhydride/calcium sulfate whisker composites

The melting and crystallization behaviors, morphology, and mechanical properties of polypropylene (PP)/surface‐treated calcium sulfate (CaSO₄) whisker (T‐CSW), β‐PP/T‐CSW, and β‐PP/polypropylene‐graft‐maleic anhydride (PP‐g‐MAH)/T‐CSW composites had been investigated via differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), polarized light microscopy (PLM), scanning electron microscopy (SEM), and mechanical tests. We found that T‐CSW was an α‐nucleating agent and increased the crystallization temperatures of PP, but PP‐g‐MAH and high loadings of T‐CSW had weakly negative effects on the crystallization rates of PP. The T‐CSW restrained the formation of β‐spherulites, and the spherulitic size decreased in the composites. PP‐g‐MAH improved the compatibility and adhesion between T‐CSW and the matrix. The notched impact strength was improved, and the tensile strength was enhanced at low levels of T‐CSW, while the flexural modulus was weakened for β‐PP/T‐CSW and β‐PP/PP‐g‐MAH/T‐CSW composites versus PP/T‐CSW composites. POLYM. COMPOS., 37:2121–2132, 2016. © 2015 Society of Plastics Engineers     

Influence of a novel β‐nucleating agent on the structure,morphology, and nonisothermal crystallization behavior of isotactic polypropylene

The crystalline structure, morphology, and nonisothermal crystallization behavior of isotactic polypropylene (iPP) with and without a novel rare earth‐containing β‐nucleating agent (WBG) were investigated with wide‐angle X‐ray diffraction, polar optical microscopy, and differential scanning calorimetry. WBG could induce the formation of the β form, and a higher proportion of the β form could be obtained by the combined effect of the optimum WBG concentration and a lower cooling rate. The content of the β form could reach more than 0.90 in a 0.08 wt % WBG nucleated sample at cooling rates lower than 5°C/min. Polar optical microscopy showed that WBG led to substantial changes in both the morphological development and crystallization process of iPP. At all the studied cooling rates, the temperature at which the maximum rate of crystallization occurred was increased by 8–11°C in the presence of the nucleating agent. An analysis of the nonisothermal crystallization kinetics also revealed that the introduction of WBG significantly shortened both the apparent incubation period for crystallization and the overall crystallization time. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermal and dynamic mechanical characterization of polypropylene‐woodflour composites

The performance of wood particle/polypropylene (PP) composites with modified compatibilities was compared. Woodflour modification was performed by esterification with maleic anhydride (MAN) and a non‐commercial maleic anhydride‐polypropylene copolymer (PPMAN) was selected as compatibilizing agent. The thermogravimetric analysis indicates that the onset of thermal degradation of treated woodflour occurs at lower temperature than that of the untreated one, and the same behavior was found in the corresponding composites. Differential scanning calorimetry indicated that both woodflours acted as nucleating agents for PP, while only treated woodflour induced PP crystallization in β‐phase in the composites. X‐ray diffractometry demonstrated that the crystallization in β‐phase was a shear‐induced phenomenon favored by the chemical modification of the woodflour surface. Dynamic mechanical studies suggested that composite properties decreased at concentrations higher than 40 wt% of woodflour and that the overall performance of MAN‐treated woodflour composites was lower than that of the composites where a compatibilizing agent was added.     

Melting characteristic and β‐crystal content of β‐nucleated polypropylene/polyamide 6 alloys prepared using different compounding methods

BACKGROUND: The distribution of nucleating agents in different phases is still an open question in general, and how to control conditions to prepare alloys rich in β‐crystals of polypropylene (PP) is hardly reported. The main goal of this study was to find out the factors influencing the β‐crystal content in β‐nucleated PP/polyamide 6 (PA6) alloys and determine the best preparation conditions to obtain β‐nucleated PP/PA6 alloys rich in β‐crystals. RESULTS: The compounding methods had little influence on the crystallization temperature of both PP and PA6. However, the melting characteristic and β‐crystal content in β‐nucleated PP/PA6 alloys not only depended upon the compounding methods, but also on the temperature at which the nucleating agent was added. A higher β‐crystal content can be obtained by adding the nucleating agent at a temperature below 190 °C, which is also dependent on the mixing time. CONCLUSION: It is proved by etching the alloys with sulfuric acid that the nucleating agent mainly disperses in the PA6 phase and/or the interface between PP and PA6 when blended at high temperature. Copyright © 2009 Society of Chemical Industry     

Comparative study on the crystallization behavior of β‐isotactic polypropylene nucleated with different β‐nucleation agents —effects of thermal conditions

In this study, the crystallization behavior of the β‐isotactic polypropylene (β‐iPP) samples nucleated by a rare earth based β‐nucleating agent (β‐NA) WBG‐II and a metal salts compound β‐NA NAB83 (denoted as WPP and NPP, respectively) under different cooling conditions were comparatively investigated. The thermal conditions such as the cooling rate, isothermal crystallization temperature, isothermal crystallization time, and the subsequent cooling to room temperature. The results of WAXD, SEM, and nonisothermal crystallization reveal that under the same processing conditions, the crystallite size of NPP is smaller, which arrange more compactly as compared with WPP. Meanwhile, NPP has shorter crystallization rate and higher β‐nucleation selectivity, but WPP can crystallization at wider temperature range. The results of isothermal crystallization showed that NPP has higher selectivity and higher β‐nucleation efficiency, which favors the formation of high proportion of β‐phase at the isothermal crystallization temperature of 110–130°C with and without subsequent cooling; WPP has lower selectivity, which can only induce high content of β‐phase under isothermal crystallization without subsequent cooling to 25°C. In tuning the crystallization behavior and the properties of β‐PP, the joint influence of the efficiency and selectivity of the β‐NA, and the thermal conditions should be taken into consideration. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40115.     

Preparation and characteristics of composites of high‐crystalline cellulose with polypropylene: Effects of maleated polypropylene and cellulose content

Binary composites of high‐crystalline fibrous cellulose with polypropylene (PP) or maleic anhydride‐grafted polypropylene (MAPP) were prepared by melt‐mixing with different contents of cellulose from 0 to 60 wt %. Ternary composites of cellulose with PP and MAPP were also prepared to investigate the effects of MAPP as a compatibilizer between cellulose and PP. Scanning electron microscopy revealed that the addition of MAPP generates strong interactions between a PP matrix and cellulose fibers: All cellulose fibers are encapsulated by layers of the matrix and connected tightly within the matrix. Thus, the tensile strength and Young's modulus of MAPP‐containing composites increase with an increase in MAPP and cellulose content, in contrast to the decrease in tensile strength of a PP‐based binary composite with an increase in cellulose. Cellulose fibers act as a nucleating agent for the crystallization of PP, which is promoted by the addition of MAPP through an increase of the crystallization temperature of PP in the composite. Accordingly, both cellulose and MAPP facilitate the thermooxidative stability of PP composites in the following order: MAPP/cellulose > PP/MAPP/cellulose > PP/cellulose > PP. Relative water absorption increases with an increase in cellulose content, decreasing with the addition of MAPP. MAPP‐containing cellulose composites have high potential for applications as environmentally friendly materials. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 337–345, 2003     

Simultaneously improving the toughness,flexural modulus and thermal performance of isotactic polypropylene by α‐β crystalline transition and inorganic whisker reinforcement

Magnesium salt (M‐HOS) whisker and β‐nucleating agent were introduced into polypropylene and their effects on the crystalline structures, morphologies, mechanical properties, and thermal resistance of polypropylene (PP) were investigated. The results of wide angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), and polar optical microscopy (POM) examinations suggested that the presence of the whisker did not cause any negative effect on the occurrence of β‐modification, and β‐phase became absolutely dominant form in β‐nucleated samples. The mechanical and thermal properties tests demonstrated that there is an excellent synergy between the β‐nucleating agent and the whisker. For PP composite containing 0.1 wt% of the β‐nucleating agent and 10 wt% of the whiskers, the Izod notched impact strength, elongation at break, flexural modulus, and heat deflection temperature were increased by 108, 194, 31, and 40%, respectively, compared with those of neat PP. By combining the toughening effect of α–β transition with the reinforcing effect of the whisker, simultaneous improvement in toughness, flexural modulus, and thermal performance of PP was successfully achieved. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Nonisothermal crystallization kinetics of polypropylene composites reinforced with down feather fiber

Nonisothermal crystallization kinetics of pure polypropylene and polypropylene/down feather fiber composites were investigated using a differential scanning calorimeter at five different cooling rates. The experimental data on crystallinity versus temperature were analyzed by Avrami, Ozawa, and Liu models, respectively. The results indicated that the presence of down feather fiber served as nucleating agent and increased the onset and peak temperatures of crystallization of polypropylene/down feather fiber composites. Interestingly, polypropylene/down feather fiber composites showed a slower primary crystallization and a faster secondary crystallization than pure PP, meaning that down feather fiber retired the crystallizaiton process of PP matrix. The nucleation activity and activation energies were also calculated and agreed well with these results. Wide‐Angle X‐ray diffraction patterns indicated that down feather fiber induced the formation of β‐monoclinic crystals in polypropylene matrix. These phenomena were definitely different from the nonisothermal crystallization kinetics of polypropylene composite based on inorganic particles and organic cellulose fibers. POLYM. COMPOS., 37:3103–3112, 2016. © 2015 Society of Plastics Engineers     

A highly efficient β‐nucleating agent for impact‐resistant polypropylene copolymer

In this work, we reported calcium tetrahydrophthalate as a high efficient β‐nucleating agent (β‐NA) for impact‐resistant polypropylene copolymer (IPC). The relative fraction of the β‐crystal can reach as high as 93.5% when only 0.03% β‐NA is added. The non‐isothermal and isothermal crystallization behaviors, morphology, lamellar structure and mechanical properties of IPCs with various β‐NA contents were studied. During non‐isothermal crystallization, the cooling rate has an important influence on the relative fraction of the β‐crystal, which decreases remarkably as the cooling rate increases. The β‐NA also greatly accelerates crystallization rate of IPC, resulting from both more crystal nuclei and larger Avrami exponent. The small angle X‐ray scattering characterization shows that more amorphous components are included into the inter‐lamellae after addition of β‐NA. Dynamical mechanical analysis (DMA) reveals that the storage modulus at low temperature and the loss factor above 0 °C from the PP component can be enhanced upon addition of β‐NA and reach a maximum at the β‐NA content of 0.05 wt %. Impact test shows that the impact strength of the IPC at 0°C can be improved as much as 40% when the content of calcium tetrahydrophthalate is 0.10 wt %. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40753.     

Mechanical and thermal characteristics and morphology of polyamide 6/isotactic polypropylene blends in the presence of a β‐nucleating agent

The mechanical and thermal characteristics and morphology of polyamide 6 (PA6)/isotactic polypropylene (iPP) blends (10/90 w/w) prepared with different processing procedures and incorporated with an aryl amide nucleating agent, a kind of β‐nucleating agent (β‐NA) for iPP, were investigated. The yield strength and flexural modulus of the blends decreased as β‐NA was introduced into the blends, whereas the impact strength and elongation at break improved. The crystalline structures of the blends closely depended on (1) the processing conditions and (2) competition between the β‐nucleating effect of β‐NA and the α‐nucleating effect of PA6 for iPP. Scanning electron microscopy, differential scanning calorimetry, and X‐ray diffraction were adopted to reveal the microstructures of the blends. At a low β‐NA content (<0.1 wt %), the α‐phase iPP dominated the blends, whereas the relative content of the β‐phase iPP increased remarkably when the β‐NA content was not less than 0.1 wt %. The processing conditions also showed profound influences on the supermolecular structures of iPP; this resulted in different mechanical properties of the blends. As for PA6, the crystallization behavior and crystalline structure did not exhibit obvious changes, but PA6 did play an important role in the epitaxial crystallization of iPP on PA6. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Investigation on β‐polypropylene/PP‐g‐MAH/ surface‐treated calcium carbonate composites

β‐Polypropylene composites containing calcium carbonate treated by titanate coupling agent (T‐CaCO₃) and maleic anhydride grafted PP (PP‐g‐MAH) were prepared by melt compounding. The crystallization, morphology and mechanical properties of the composites were investigated by means of differential scanning calorimetry, wide‐angle X‐ray diffraction, polarized light microscopy, scanning electron microscopy and mechanical tests. It is found that both T‐CaCO₃ and NT‐C are able to induce the formation of β‐phase, and NT‐C greatly increases the β content and decreases the spherulitic size of PP. PP‐g‐MAH facilitates the formation of β‐form PP and improves the compatibility between T‐CaCO₃ and PP. Izod notched impact strength of β‐PP/T‐CaCO₃ composite is higher than that of PP/T‐CaCO₃ composite, indicating the synergistic toughening effect of T‐CaCO₃ and β‐PP. Incorporation of PP‐g‐MAH into β‐PP/T‐CaCO₃ composite further increases the content of β‐crystal PP and improves the impact strength and tensile strength when T‐CaCO₃ concentration is below 5 wt%. The nonisothermal crystallization kinetics of β‐PP composites is well described by Jeziorny's and Mo's methods. It is found that NT‐C and T‐CaCO₃ accelerate the crystallization rate of PP but the influence of PP‐g‐MAH on crystallization rate of β‐PP composite is marginal. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Controllable reinforcement of stiffness and toughness of polypropylene via thermally induced self‐assembly of β‐nucleating agent

An easy approach was reported to achieve the simultaneous reinforcement and toughening of polypropylene (PP) via thermally induced self‐assembly of β‐nucleating agent (TMB‐5). The results showed that the processing temperatures dictated the solubility and self‐assembly of TMB‐5 in the polymer melts to determine the subsequent morphology development of PP. At low processing temperature, TMB‐5 did not dissolve into the polymer melt but remained original shape to induce PP to crystallize into spherulites so that it only promoted the formation of β‐form crystals to enhance the toughness of the samples. At high processing temperature, TMB‐5 gradually dissolved into the polymer melts. On cooling, the dissolved nucleating agent self‐assembled into high aspect ratio fibrils through intermolecular hydrogen‐bonding interactions. Due to a favorable matching between PP and TMB‐5, PP preferred to nucleate and grow orthogonally to the fibril axis and into oriented hybrid shish‐kebab morphology with rich β‐form crystals. Compared with isotropic spherulites, the anisotropic structure exhibited excellent properties of the β‐form crystal and shish‐kebab morphology to simultaneously improve the strength and toughness of TMB‐5‐modified PP samples. With the increasing processing temperature, more dissolved TMB‐5 was involved in the self‐assembly procedure to generate longer fibrils and induce more lamellae to grow on the surface. As a consequence, the anisotropy of the PP samples increased further, bringing out more improvements of the tensile strength. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40605.     

Detecting crystallization structure evolution of polypropylene injection‐molded bar induced by nucleating agent

The crystallization structures of Polypropylene (PP) injection‐molded bars nucleated by nucleating agent were detected from the skin layer to the core zone, layer by layer. α‐phase nucleating agent 1,3:2,4‐bis (3,4‐dimethylbenzylidene) sorbitol (DMDBS, Millad 3988), β‐phase nucleating agent aryl amides compounds (TMB‐5), and their compounds were introduced into PP matrix, respectively. The relative content of β‐phase PP in the different zones of an injection‐molded bar was characterized and calculated by Wide angle X‐ray diffraction (WAXD) and Differential scanning calorimetry (DSC). The results show that, whether in pure PP or in nucleated PP, both β‐phase PP and α‐phase PP grow in the skin layer of the injection‐molded bar. However, in the intermediate layers and the core zone, the crystallization structures of PP are dependent on the used nucleating agent. β‐phase is the main crystallization structure of TMB‐5 (0.1 and 0.2 wt%) nucleated PP, and α‐phase in DMDBS (0.1 and 0.2 wt%) nucleated PP. Compounding nucleating agents with 0.1 wt% DMDBS and 0.1 wt% TMB‐5 induces PP crystallization almost in β‐phase; however, PP nucleated by 0.2 wt% DMDBS and 0.2 wt% TMB‐5 crystallizes exclusively in α‐phase. The crystallization mechanism of PP nucleated by compounding nucleating agents was further studied in this work. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Influence of different β‐nucleating agent on crystallization behavior,morphology, and melting characteristic of multiwalled carbon nanotube‐filled isotactic polypropylene nanocomposites

To obtain isotactic polypropylene (iPP) nanocomposites with high β‐crystal content, TMB5, calcium pimelate and calcium pimelate supported on the surface of nano‐CaCO₃ were used as β‐nucleating agent and MWCNT filled β‐nucleated iPP nanocomposites were prepared. The effect of different β‐nucleating agent and MWCNT on the crystallization behavior and morphology, melting characteristic and β‐crystal content of β‐nucleated iPP nanocomposites were investigated by DSC, XRD and POM. The results indicated that addition of MWCNT increased the crystallization temperature of iPP and MWCNT filled iPP nanocomposites mainly formed α‐crystal. The β‐nucleating agent can induce the formation of β‐crystal in MWCNT filled iPP nanocomposites. The β‐nucleating ability and β‐crystal content in MWCNT filled β‐nucleated iPP nanocomposites decreased with increasing MWCNT content and increased with increasing β‐nucleating agent content due to the nucleation competition between MWCNT and β‐nucleating agents. It is found that the calcium pimelate supported on the surface of inorganic particles as β‐nucleating agent has stronger heterogeneous β‐nucleation than calcium pimelate and TMB5. The MWCNT filled iPP nanocomposites with high β‐crystal content can be obtained by supported β‐nucleating agent. POLYM. COMPOS., 36:635–643, 2015. © 2014 Society of Plastics Engineers     

Design of new polypropylene–woodflour composites: Processing and physical characterization

Woodflour/polypropylene composites were prepared with 10 and 20% in weight of woodflour (WF). The influence of the WF, the compatibilizer, and processing aid (WP) in the crystalline structure of the polypropylene was studied by thermal analysis. The results showed that the WF acts as a nucleating agent, increasing the crystallization rate of the PP at the cooling rates studied. The morphological study by SEM proved that the WP increased the dispersion of the filler into the PP matrix, and the ionomer, used like compatibilized improved the adhesion between the PP and the filler obtaining a more uniform morphology. The mechanical properties indicated that the incorporation of the ionomer and the WP enhanced the ductility of the composites at the same time that the materials reached a more uniform morphology. The amount of additives (compatibilizer and WP) included in the woodflour-plastic composite (WPC) formulations was small, for this, the formulations are suitable to use in a possible industrial application. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Highly active thermally stable β‐nucleating agents for isotactic polypropylene

Calcium salts of suberic (Ca‐Sub) and pimelic (Ca‐Pim) acids were synthesized and implemented as in different grades of isotactic polypropylene (iPP). Propylene homopolymer, as well as random and block copolymers containing these additives, crystallized iPP into pure or nearly pure β modification in the isothermal and nonisothermal crystallization experiments. Recently, Ca‐Sub proved to be the most effective β‐nucleating agent of iPP. The Ca‐Sub nucleating agent widens the upper crystallization temperature range of pure β‐iPP formation up to 140°C. In this study the effect of the these additives on the crystallization, melting characteristics, and structure of the PP were studied. The degree of crystallinity of β‐iPP was markedly higher than that of α‐iPP. A widening in the melting peak of the samples crystallized in a high temperature range was first observed and discussed in regard to literature results of the same phenomenon for α‐iPP. The morphology of the β‐iPP samples was revealed by scanning electron microscopy. Independent of the type of polymer or nucleating agent, hedritic structures were found in the early stages of growth of the β‐spherulites. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2357–2368, 1999     

A novel β‐nucleating agent for isotactic polypropylene

The nucleating ability of p‐cyclohexylamide carboxybenzene (β‐NA) towards isotactic polypropylene (iPP) was investigated by differential scanning calorimetry, X‐ray diffraction, polarized optical microscopy and scanning electron microscopy. β‐NA is identified to have dual nucleating ability for α‐iPP and β‐iPP under appropriate kinetic conditions. The formation of β‐iPP is dependent on the content of β‐NA. The content of β‐phase can reach as high as 96.96% with the addition of only 0.05 wt% β‐NA. Under non‐isothermal crystallization the content of β‐iPP increases with increasing cooling rate. The maximum β‐crystal content is obtained at a cooling rate of 40 °C min^–1. The supermolecular structure of the β‐iPP is identified as a leaf‐like transcrystalline structure with an ordered lamellae arrangement perpendicular to the special surface of β‐NA. Under isothermal crystallization β‐crystals can be formed in the temperature range 80–140 °C. The content of β‐crystals reaches its maximum value at a crystallization temperature of 130 °C. © 2012 Society of Chemical Industry     

The effects of crystallization condition on the microstructure and thermal stability of istactic polypropylene nucleated by β‐form nucleating agent

This article deals with the crystallization behaviors of original (prepared in a torque rheometer), DSC crystallization and mold crystallization (quenching and slow nonisothermal crystallization) of isotactic polypropylene (iPP) mixed with β‐form nucleating agent. The microstructure and thermal stability of these samples were investigated. The wide angle X‐ray diffraction (WAXD) results indicate that fast cooling is favorable for β‐form iPP formation. With slower cooling rate and higher concentration of nucleating agent, the lamellar thickness and stability of crystal0s were enhanced. Polarized optical microscopy (POM) and scanning electron microscopy (SEM) both showed that rapid crystallized samples gave rise to tiny spherulites, whereas under slow crystallization condition, nucleated samples could be fully developed in the form of dendritic or transcrystalline structures, depending on the nucleating agent concentration. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011