Synthesis of Long Afterglow SrAl2O4 :Eu2+, Dy3+ Phosphor by Microemulsion Method

Long afterglow SrAl2 O4: Eu2 , Dy3 phosphor was synthesized by microemulsion method. The synthesized phosphor was characterized by XRD. XRD pattern indicates that the phosphor has monoclinic SrAl2 O4 crystal structre.The microstructure of the phosphor was investigated by SEM and TEM. The excitation spectrum, emission spectrum and afterglow decay curve were measured, the wide range of excitation wavelength indicated that the luminescent material could be excited by the light from ultraviolet ray to visible light, and the emission maximum was found to peak mainly at λem of 525 nm. The sample excited by ultraviolet visible light could emit bright green light.     

SrAl2O4:Eu, Dy Nanometer Phosphors Synthesized by Combustion Method

SrAl2 O4: Eu, Dy nanometer phosphors were synthesized by combustion method at 500 ～ 900℃, followed by heating the combustion sample at 1150℃ at a weak reductive atmosphere and nanometer phosphor with much better luminescent properties was obtained. The influences of the initiating combustion temperature, H3BO3 quantity, the mass ratio of urea and nitrate on the luminescent intensity of nanometer phosphors were studied. The optimum synthetic conditions were determined. The analysis results by transmission electron microscopy (TEM) indicate that the particle size of the synthetic product is less than 75 nm. The luminescent materials do not need to be ground. Their coating can be refined. It supplies a new approach to the rapid preparation of the luminescent materials at low temperature. The excitation and emission spectra indicate that the main peaks in the excitation and emission spectrum of nanometer phosphor synthesized by combustion method shifted to the short wavelength compared with the phosphor obtained by the solidstate reaction synthesis method. The reason of blue shift was explained. The afterglow decay results indicate that the decay speed of the afterglow for nanometer phosphor is faster than that obtained by the solid-state reaction method.     

SrAl_2O_4∶Eu~(2+),Nd~(3+) and Dy~(3+) Long Afterglow Phosphor

Longafterglowphosphorabsorbingenergyfromsolar,lampandotherlightsourcesforashorttimestorestheenergyandexhibitsbrightandlong lastingphosphorescencewhichsuitsthevisualperceptionofthehumaneyewithminimumbrightness 0 32mcd·m- 2 andlastingtimemorethan 8h) .TheSrAl2 O4 ∶Eu2 +,Dy3+phosphorhasbeenknowntobeagreenlongafterglowphosphorwithanemissionpeakat 5 2 0nm[1～ 7] .ThepropertiesofthephosphorwerefurtherexaminedbythegroupofTangMingdaoandMatsuzawaTindetailin 1995and 1996respectively[1,2 ] .Inorde…     

Synthesis of Long Afterglow Photoluminescent Materials Sr_2MgSi_2O_7∶Eu~(2 ), Dy~(3 ) by Sol-Gel Method

Withtheprogressofsocialcivilizationanddevel opmentofmodernscienceandtechnology ,thedemandforluminescentmaterialskeepsincreasingduetoitsgreatsocialandeconomicbenefits .Therefore ,prepa rationofluminescentmaterialswasregardedbypeopleveryearly .Asanembellish…     

Preparation and Luminescence Properties of the New Long Phosphorescent Phosphors Ba1-xCaxAl2O4∶Eu2+,Dy3+

New long phosphorescent phosphors Ba1-xCaxAl2O4∶Eu2 , Dy3 with tunable color emission were prepared and studied. The emission spectra show that the tuning range of the color emission of the phosphors is between 498 and 440 nm, which is dependent on x, under the excitation of UV. The wavelength of the afterglow increases with the increasing of x until x equals 0.6. The XRD patterns show that the single phase limit in the phosphors is below x value of 0.4. The Thermoluminescence spectra were measured to investigate the traps created by the doping of Dy3 .     

蓝色长余辉发光材料CaAl2O4∶Eu2+, Dy3+的制备

用溶胶—凝胶法(Sol—gel)制备蓝色长余辉发光材料CaAl2O4∶Eu2+,Dy3+(CED),用差热分析(DTA)、红外光谱分析(IR)、X射线粉晶衍射(XRD)、荧光光度计对合成制备产物进行了系列分析测定,确定了制备的最佳条件,产物的激发波长为328nm,发射波长为440nm。     

Synthesis of Long Afterglow Phosphors MAl2O4:Eu2+, Dy3+(M=Ca, Sr, Ba) by Microemulsion Method and Their Luminescent Properties

Long afterglow phosphors MAl2O4:Eu2 , Dy3 (M=Ca, Sr, Ba) were synthesized by microemulsion method, and their crystal structure and luminescent properties were compared and investigated. XRD patterns of samples indicate that phosphors CaAl2O4:Eu2 , Dy3 and SrAl2O4:Eu2 , Dy3 are with monoclinic crystal structure and phosphor BaAl2O4:Eu2 , Dy3 is with hexagonal crystal structure. The wide range of excitation spectrum of phosphors MAl2O4:Eu2 , Dy3 (M=Ca,Sr,Ba) indicates that the luminescent materials can be excited by light from ultraviolet ray to visible light and the maximum emission wavelength of phosphors MAl2O4:Eu2 , Dy3 (M=Ca, Sr, Ba) is found mainly at λem of 440 nm (M=Ca), 520 nm (M=Sr) and 496 nm (M=Ba) respectively, the corresponding colors of emission light are blue, green and cyna-green respectively. The afterglow decay tendency of phosphors can be summarized as three processes: initial rapid decay, intermediate transitional decay and very long slow decay. Afterglow decay curves coincide with formula I=At-n, and the sequence of afterglow intensity and time is Sr＞Ca＞Ba.     

Preparation and characterization of flower-like SrAl2O4:Eu2+,Dy3+ phosphors by sol-gel process

A flower-like Eu2+ and Dy3+ co-doped SrAl2O4 long-lasting phosphorescent (LLP) phosphor was synthesized via the inorganic- salt-based sol-gel method.The crystal structure,morphology and optical properties of the composite were characterized.X-ray diffraction diffu-sion (XRD) data and DSC-TG curves of the phosphor revealed that the SrAl2O4 crystallites have been formed after the precursor was calcined at 900 °C and to be single-phase SrAl2O4 at 1100 °C.The SEM photographs indicated that the sample exhibited ...     

Synthesis of Long Afterglow Phosphor CaAl2Si2O8:Eu2+, Dy3+ via Sol-Gel Technique and Its Optical Properties

The long afterglow phosphor CaAl2Si2O8:Eu2 , Dy3 was prepared by a sol-gel method. The sol-gel process and the structure of the phosphor were investigated by means of X-ray diffraction analysis (XRD). It is found that the single anorthite phase formed at about 1000 ℃, which is 300 ℃ lower than that required for the conventional solid state reaction. The obtained phosphor powders are easier to grind than those of solid state method and the partical size of phosphor has a relative narrow distribution of 200 to 500 nm. The photoluminescence and afterglow properties of the phosphor were also characterized. An obvious blue shift occurs in the excitation and emission spectra of phosphors obtained by sol-gel and solid state reaction methods. The change of the fluorescence spectra can be attributed to the sharp decrease of the crystalline grain size of the phosphor resulted from the sol-gel technique.     

Mg~（2＋）,Ca~（2＋）,Ba~（2＋）离子部分取代对SrAl_2O_4：Eu~（2＋）,Dy~（3＋）晶体结构和发光性能的影响

采用高温固相反应法制备了Sr0.9M0.1Al2O4：Eu2＋,Dy3＋（M=Mg,Ca,Ba）长余辉发光材料,并对其晶体结构、光谱性质、余辉特性进行了分析.X射线衍射测试结果表明,Mg2＋,Ca2＋,Ba2＋离子部分取代SrAl2O4基质中的Sr后,基质晶体结构并没有发生改变.光谱测试结果表明,Mg2＋,Ca2＋,Ba2＋取代后发光材料的激发光谱都是一个从250~450 nm范围内的宽激发带,在266nm,320nm,360nm,416 nm处各有一个激发峰.发射光谱中Mg2＋和Ba2＋的取代使波长出现蓝移,而Ca2＋的取代使波长出现红移.余辉测试结果表明,Ca2＋取代后的余辉时间长于Mg2＋和Ba2＋的取代.     

Preparation of Incompact Strontium Aluminate Phosphors

The incompact long afterglow pigment SrAl2O4: Eu, Dy was synthesized by ceramics technology.The agglomerated starting raw material had little effect on the synthesis of SrA12O4 matrix through solid-state reaction method,but the shrinkage and densification was retarded greatly by the agglomerated powder by the formation of large and extensive pore network.The sintering mechanism is surface diffusion ( without flux B2O3 ) and grain boundary diffusion (with B2O3 as flux)respectively, and the as-prepared long afterglow pigment glows in the dark for over 4000 min.     

新型红色长余辉发光材料Y2O3∶Eu3+,Ca2+,Ti4+的燃烧合成和性能表征

采用燃烧法合成了新型红色长余辉发光材料Y2O3∶Eu3+,Ca2+,Ti4+.用X射线衍射仪表征了其结构;用荧光光谱仪测试了激发、发射光谱;以紫外-可见分光光度计测定分析了样品的反射光谱特征.XRD分析证实为立方相的Y2O3.激发光谱为一紫外区内的宽带谱,中心位于253nm,属于Eu3+-O2-的电荷迁移跃迁;发射光谱峰值位于613 nm,对应于Eu3+的5D0→7F2跃迁发射.由于掺杂离子不等价的取代Y3+,形成了电子陷阱和空穴陷阱,两者的复合作用延缓了余辉的衰减.紫外-可见反射光谱得到的结论与荧光激发光谱的结果一致.该样品在紫外线激发下余辉时间长达90分钟.     

活性炭对长余辉发光材料SrAl2O4：Eu^2＋，Dy^3＋发光性能的影响

采用高温固相法制备SrAl2O4:Eu2+,Dy3+长余辉发光材料.借助材料的发射光谱、激发光谱,分析研究活性炭装法和活性炭含量对SrAl2O4:Eu2+,Dy3+发光材料发光性能的影响.结果表明:活性炭作为一种还原剂,装法和含量的变化能改变发光材料的发射光谱和激发光谱,活性炭覆盖在前躯体表面加热所制得样品的发光效果好,当活性炭含量为12%～20%时,所制得的样品具有质地疏松、发光强度好等特点.     

Synthesis of Long Afterglow Phosphors Doped B SrAl2O4:Eu2+, Dy3+ and Its Luminescent Properties

The long afterglow luminescent material SrAl₂O₄: Eu²⁺, Dy³⁺ was prepared by high temperature solid-state method. Effects of doped B on the luminescent properties of phosphors SrAl₂O₄: Eu²⁺, Dy³⁺ were investigated by means of excitation spectra, emission spectra and X-ray diffraction analysis. As the result, the addition of H₃BO₃ as flux promotes the growth of crystalline and reduces the synthesizing temperature, but the wavelength of emission peak of photoluminescent material did not change with the variation of H₃BO₃ content. The effect of Dy³⁺ concentration on the luminescent properties of material was investigated. It was found that the luminescence of phosphors prepared under the condition of the amount of H₃BO₃ 5% and the mole ratio of Eu/Dy = 1/7(Eu = 0.02 mole) had better luminescent property and longer afterglow time.     

Adjustable Luminescence of SrAl2O4：Eu^2＋ , Dy^3＋ Assembled in Zeolite

Capsulating guest into the nanometer yoids of zeolites is a effective way to form novel host-guest material. In our work, stoichiometric SrAl2O4: Eu^2 , Dy^3 sol guest was prepared by sol-gel method and assembled into the nanometer channels of zeolite ZSM-5 host through mechanical mixing, hydrothermal reaction and microwave heating reaction, respectively. After being reduced and diffused in a microwave muffle, the fluorescence spectra of the host-guest materials exhibit remarkable blue shifts in comparison of that of SrAl2O4 : Eu^2 , Dy^3 . Some interesting phenomena in the assembled hostguest materials are that the after-glow emission spectra exist two bands at about 400 nm and 517 nm and the relative strengths of these two bands can be adjusted by changing the assembly methods and the assembly concentration. These are attributed to the fact that the phosphor was capsulated into the voids of zeolite ZSM-5 and generated the quantum size effect and the host-guest effect.     

Hydrothermal preparation and persistence characteristics of nanosized phosphor SrS：Eu^2＋,Dy^3＋

Nanosized long-persistent phosphors SrS: Eu2+, Dy3+ were prepared by the hydrothermal method. The samples were characterized by X-ray powder diffraction, transmission electron microscopy, and charge-coupled device spectrometry. The persistence characteristic was studied using the decay curves. The results showed that the emission intensity decreased sharply with temperature increasing, although the particle size increased. The S2- vacancies caused by oxidization served as shallow traps, and Dy3+ served as deep traps in SrS: Eu2+, Dy3+. The afterglow intensity of SrS: Eu2+, Dy3+ was higher than that of SrS: Eu2+ prepared at the same temperature. However, the minimization span of initial afterglow with temperature for the former sample was larger than that for the latter. Binary-doped phosphor decayed more slowly than the singly doped one. The afterglow of SrS: Eu2+, Dy3+ decayed more quickly with the increase of sintering temperature.     

Preparation and Luminescence of SrAi2O4:Eu2+, Dy3+ Nano-Particle

SrAl2O4: Eu2 , Dy3 nano-particle luminescence material was prepared by sol-gel method. Influences of synthesis conditions on the particle size and luminescence properties of SrAl2O4: Eu2 , Dy3 were studied. The synthesis process and the properties of the samples were analyzed by DTA, TGA, XRD, SEM. The result suggested that the formation of SrAl2O4: Eu2 , Dy3 sol is a slow heat release process beginning at 500 ℃ and peaking at 759 ℃.SrAl2O4: Eu2 ,Dy3 crystalline was formed at 1100 ℃. The luminescence properties of the SrAl2O4: Eu2 , Dy3 nanoparticle were compared with the conventional SrAl2O4: Eu2 , Dy3 particles. The average particle size of the product is about 30 nm. The excitation spectrum of the sample shows a broad band with peaks at 240, 330, 378 and 425 nm. The emission spectrum is a broadband spectrum with a peak at 523 nm.     

燃烧法合成稀土纳米长余辉发光材料SrO·xAl2O3:Eu2+,Dy3+

应用燃烧法在空气中较低的温度(<900℃)下成功地合成了SrO·xAl2O3∶Eu2+,Dy3+稀土纳米长余辉发光材料,并研究了炉温、反应物中铝锶比、助溶剂和可燃物等对发光材料性能的影响。研究结果表明,反应物置于温度为600℃的高温炉中时燃烧得到的产物性能最好,发光粉的粒径在70nm左右,发射光谱的最大波长在520nm左右。与其它合成方法相比,该方法具有合成温度低、反应时间短,获得的产物疏松、硬度小、粒度小等优点。     

Preparation of Non-Grinding Long Afterglow SrAl2O4 ：Eu^2＋ , Dy^3＋ Material by Microwave Combustion Method

The non-grinding long afterglow material SrAl2O4：Eu^2＋ , Dy^3＋ was prepared by combustion method in home mierowave oven direetly, after dispersant, frother, eomburent, and mineralizer were added into the reacting system. XRD analysis showed that the powders were nearly pure SrAl2O4 phase with few other phases, and the size of the grain was 41.1 nm. Fluoreseenee speetrum results indieated that there were 2 exeitation peaks loeated at 345 and 400 nm, and the emission peak loeated at 516 nm, afterglow lasted up to 30 min or more. The mierowave eombustion method has advantages of less time, low temperature and no grinding process, and the material made by the method has good luminescent property.