Combustion of jojoba methyl ester in an indirect injection diesel engine

An experimental investigation has been carried out to examine for the first time the performance and combustion noise of an indirect injection diesel engine running with new fuel derived from pure jojoba oil, jojoba methyl ester, and its blends with gas oil. A Ricardo E6 compression swirl diesel engine was fully instrumented for the measurement of combustion pressure and its rise rate and other operating parameters. Test parameters included the percentage of jojoba methyl ester in the blend, engine speed, load, injection timing and engine compression ratio. Results showed that the new fuel derived from jojoba is generally comparable and good replacement to gas oil in diesel engine at most engine operating conditions, in terms of performance parameters and combustion noise produced.     

Performance, emission and combustion characteristics of biodiesel fuelled variable compression ratio engine

Experiments has been carried out to estimate the performance, emission and combustion characteristics of a single cylinder; four stroke variable compression ratio multi fuel engine fuelled with waste cooking oil methyl ester and its blends with standard diesel. Tests has been conducted using the fuel blends of 20%, 40%, 60% and 80% biodiesel with standard diesel, with an engine speed of 1500 rpm, fixed compression ratio 21 and at different loading conditions. The performance parameters elucidated includes brake thermal efficiency, specific fuel consumption, brake power, indicated mean effective pressure, mechanical efficiency and exhaust gas temperature. The exhaust gas emission is found to contain carbon monoxide, hydrocarbon, nitrogen oxides and carbon dioxide. The results of the experiment has been compared and analyzed with standard diesel and it confirms considerable improvement in the performance parameters as well as exhaust emissions. The blends when used as fuel results in the reduction of carbon monoxide, hydrocarbon, carbon dioxide at the expense of nitrogen oxides emissions. It has found that the combustion characteristics of waste cooking oil methyl ester and its diesel blends closely followed those of standard diesel.     

Environmental effect of rapeseed oil ethyl ester

Exhaust emission tests were conducted on rapeseed oil methyl ester (RME), rapeseed oil ethyl ester (REE) and fossil diesel fuel as well as on their mixtures. Results showed that when considering emissions of nitrogen oxides (NO_x), carbon monoxide (CO) and smoke density, rapeseed oil ethyl ester had less negative effect on the environment in comparison with that of rapeseed oil methyl ester. When fuelled with rapeseed oil ethyl ester, the emissions of NO_x showed an increase of 8.3% over those of fossil diesel fuel. When operated on 25–50% bio-ester mixed with fossil diesel fuel, NO_x emissions marginally decreased. When fuelled with pure rapeseed oil ethyl ester, HC emissions decreased by 53%, CO emissions by 7.2% and smoke density 72.6% when compared with emissions when fossil diesel fuel was used. Carbon dioxide (CO₂) emissions, which cause greenhouse effect, decreased by 782.87 g/kWh when rapeseed oil ethyl ester was used and by 782.26 g/kWh when rapeseed oil methyl ester was used instead of fossil diesel fuel. Rapeseed oil ethyl ester was more rapidly biodegradable in aqua environment when compared with rapeseed oil methyl ester and especially with fossil diesel fuel. During a standard 21 day period, 97.7% of rapeseed oil methyl ester, 98% of rapeseed oil ethyl ester and only 61.3% of fossil diesel fuel were biologically decomposed.     

Environmental impact of an algal biofuel doped with carbon black

This paper investigated the role of the emission characteristics of a diesel engine when carbon black (CB) blended with Caulerpa peltata algae oil methyl ester (CPOME) is used as a fuel. Biodiesels are produced from Caulerpa peltata algae oil (CPO) by the transesterification process. The biodiesel blends containing 10%, 15%, and 20% CB were denoted as B20, B20CB10, B20CB15, and B20CB20. The CPOME was mixed with CB nanoparticles with the aid of a mechanical stirrer. The fuel properties of all blends were studied and compared according to ASTM standard. Tests were performed at full-load CI engine operation with a constant speed of 1500 rpm. The acquired data were studied for various parameters, such as exhaust emissions of HC, CO, CO₂, NOx, and smoke opacity.     

Fuel properties and exhaust emissions of low blending rate soybean oil methyl esters blended with diesel fuel

The main properties and engine emissions of low blending rate soybean oil methyl ester blended with diesel from 5 to 30 wt% were compared and analyzed. The experimental results show that, compared with diesel fuel, with an increase in the soybean oil methyl ester percentage in the blends, distillation temperature at 50%, flash point, kinematic viscosity, specific gravity, gelatine content, carbon residue, acidity and ash increase while a cold filter plugging point, solidifying point and copper corrosion keep constant, sulfur content decreases, smoke density and HC decrease while NO_x emission increase, CO increases at 2,200 r/min but decreases at 3,400 r/min.     

Emission analysis of Azolla methyl ester with BaO nano additives for IC engine

The aim of this work is to decrease emissions in diesel engines fueled with diesel and algae biodiesel blends and also addition of BiO nanoparticles. Azolla algae can be used to produce biodiesel, because of high oil content. The biodiesel was prepared by using Azolla algae non-edible oil through transesterification process. In the present study, the BaO nano additives into the algae oil-based methyl ester blend and its diesel blends are analyzed the emission characteristic at different load. Addition of BaO nanoparticle was a strategy to reduce emission (CO, HC, and O₂) of the biodiesel.     

Emission analysis of Azolla methyl ester with Bi2O3 nano additives for IC engine

This work investigates the effect of using Bi₂O₃ nanoparticles at a different proportion of Azolla algae methyl ester in a four-stroke single cylinder diesel engine. Azolla algae can be used to produce biodiesel, because of high oil content. Biodiesel is developed by the transesterification of oil. In the present study, the Bi₂O₃ nano additives into the oil-based methyl ester blend and its diesel blends are analyzed the emission characteristic at different load. Addition of Bi₂O₃ nanoparticle is a strategy to reduce emission (CO, HC and smoke) of the biodiesel.     

Direct injection diesel engine performance,emission, and combustion characteristics using diesel fuel,nonedible honne oil methyl ester,and blends with diesel fuel

Honne oil methyl ester (HOME) is produced from a nonedible vegetable oil, namely, honne oil, available abundantly in India. It has remained as an untapped new possible source of alternative fuel that can be used for diesel engines. The present research is aimed at investigating experimentally the performance, exhaust emission, and combustion characteristics of a direct injection diesel engine (single cylinder, water cooled) typically used in agricultural sector over the entire load range when fuelled with HOME and diesel fuel blends, HM20 (20% HOME + 80% diesel fuel)–HM100. The properties of these blends are found to be comparable with diesel fuel conforming to the American and European standards. The combustion parameters of HM20 are found to be slightly better than neat diesel (ND). For other blend ratios, these combustion parameters deviated compared with ND. The performance (brake thermal efficiency (BTE), brake‐specific fuel consumption, and exhaust gas temperature) of HM20 is better than ND. For other blend ratios, BTE is inferior compared with ND. The emissions (CO and SO) of HM20–HM100, throughout the entire load range, are dropped significantly compared with ND. Unburned hydrocarbon emissions of HM20–HM40, throughout the entire load range, is slightly decreased, whereas for other blend ratios, it is increased compared with ND. NO_x emissions of HM20, throughout the entire load range, is slightly increased, whereas for other blend ratios, it is slightly decreased. The reductions in exhaust emissions together with increase in BTE made the blend HM20 a suitable alternative fuel for diesel fuel and thus could help in controlling air pollution. Copyright © 2011 John Wiley & Sons, Ltd.     

Hydrogen enriched waste oil biodiesel usage in compression ignition engine

In the present study, hydrogen enrichment for biodiesel-diesel blends was evaluated to investigate the performance and emission characteristics of a compression ignition engine. Biodiesel was obtained from waste oil and blended to pure diesel fuel by volume fraction of 0%, 10% and 20%. After that, pure hydrogen was introduced through the intake air at different flow rates. Effects of pure hydrogen on performance and emission characteristics were investigated by evaluating power, torque, specific fuel consumption, CO, CO₂ and NO_x emissions. Experimental study revealed that waste oil biodiesel usage deteriorated performance and emission parameters except CO emissions. However, the enrichment test fuels with hydrogen fuel can improve performance characteristics and emission parameters, whereas it increased NO_x emissions. Brake thermal efficiency and specific fuel consumption were improved when the test fuels enriched with hydrogen gas. Because of absence of carbon atoms in the chemical structure of the hydrogen fuel, hydrogen addition dropped CO and CO₂ emissions but increment in cylinder temperature caused rising in NO_x emissions.     

Performance and emission characteristics of a DI compression ignition engine operated on Honge, Jatropha and sesame oil methyl esters

The high viscosity of vegetable oils leads to problem in pumping and spray characteristics. The inefficient mixing of vegetable oils with air contributes to incomplete combustion. The best way to use vegetable oils as fuel in compression ignition (CI) engines is to convert it into biodiesel. Biodiesel is a methyl or ethyl ester of fatty acids made from vegetable oils (both edible and non-edible) and animal fat. The main resources for biodiesel production can be non-edible oils obtained from plant species such as Pongamia pinnata (Honge oil), Jatropha curcas (Ratanjyot), Hevea brasiliensis (Rubber) and Calophyllum inophyllum (Nagchampa). Biodiesel can be used in its pure form or can be blended with diesel to form different blends. It can be used in CI engines with very little or no engine modifications. This is because it has properties similar to mineral diesel. This paper presents the results of investigations carried out on a single-cylinder, four-stroke, direct-injection, CI engine operated with methyl esters of Honge oil, Jatropha oil and sesame oil. Comparative measures of brake thermal efficiency, smoke opacity, HC, CO, NO_X, ignition delay, combustion duration and heat release rates have been presented and discussed. Engine performance in terms of higher brake thermal efficiency and lower emissions (HC, CO, NO_X) with sesame oil methyl ester operation was observed compared to methyl esters of Honge and Jatropha oil operation.     

Environment-friendly fuel Cymbopogon flexuosus: Analysis of fuel properties,performance, and emission parameters of a Direct Injection Compression Ignition research engine

The novelty of this study  discusses on the influence of neat lemongrass oil (LGO) on fuel analysis, performance and emission analysis, naturally aspirated diesel engine. The critical parameters include iodine value, flash point, kinematic viscosity, saponification and cetane numbers, calorific value, Fourier transform infrared spectroscopy (FT-IR), and gas chromatography–mass spectroscopy (GC-MS) studies were investigated. The oxygenated elements, such as naphthalene, caryophyllene, pentadecanoic acid, dihydropyridine, d -limonene are observed using GC-MS analysis. The higher hydrocarbon (HC) chain length indicates a rise in energy density and boiling point with a reduction of volatility. Using FT-IR analysis, C–H stretching vibrations are found at a frequency of 1672 cm⁻¹. The C≐C stretching vibrations at 1740 cm⁻¹ reveals the availability of the alkenes/fingerprint phase. Experiments were conducted at four different volumetric blend ratios of LGO-diesel blends at typical injection parameters under different loading conditions. Brake thermal efficiency (BTE) decreased for all the test combinations of LGO than diesel. BTE is observed as 30.79% at diesel, 30.06% at LGO25, 28.71% at LGO50, 27.77% at LGO75%, and 27.23% at LGO100. The cylinder pressure and heat release rate increased proportionately with the LGO fuel mixture. Carbon monoxide, HC, and smoke emissions are reduced by LGO mixtures than diesel at the full load of the engine. It was noted that greater blends of LGO and diesel resulted in increased nitrogen oxide (NO_x) emissions and engine tribological characteristics. The NO_x is increased by 21.2% at LGO25, 24.3% at LGO50, 26.5% at LGO75 and 30.8% at LGO100 when compared with diesel. Without any chemical processing, Cymbopogon flexuosus oil can be blended directly with diesel fuel.     

Experimental investigation of control of NOx emissions in biodiesel-fueled compression ignition engine

Biodiesel is an alternative fuel consisting of the alkyl esters of fatty acids from vegetable oils or animal fats. Vegetable oils are produced from numerous oil seed crops (edible and non-edible), e.g., rapeseed oil, linseed oil, rice bran oil, soybean oil, etc. Research has shown that biodiesel-fueled engines produce less carbon monoxide (CO), unburned hydrocarbon (HC), and particulate emissions compared to mineral diesel fuel but higher NO_x emissions. Exhaust gas recirculation (EGR) is effective to reduce NO_x from diesel engines because it lowers the flame temperature and the oxygen concentration in the combustion chamber. However, EGR results in higher particulate matter (PM) emissions. Thus, the drawback of higher NO_x emissions while using biodiesel may be overcome by employing EGR. The objective of current research work is to investigate the usage of biodiesel and EGR simultaneously in order to reduce the emissions of all regulated pollutants from diesel engines. A two-cylinder, air-cooled, constant speed direct injection diesel engine was used for experiments. HCs, NO_x, CO, and opacity of the exhaust gas were measured to estimate the emissions. Various engine performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC), and brake specific energy consumption (BSEC), etc. were calculated from the acquired data. Application of EGR with biodiesel blends resulted in reductions in NO_x emissions without any significant penalty in PM emissions or BSEC.     

Emission characteristics of diesel fuel composed of linseed oil (Linum Usitatissium) blends utilizing rice husk producer gas

This paper highlights the experimental investigation of the emission characteristics of linseed oil blended with rice husk producer gas in a diesel engine modified to dual mode. Linseed oil was assessed in both single and dual-fuel mode with a constant gas flow rate of 21.69 kg/h at distinctive load conditions. From the experimental values it is seen that both oxides of nitrogen (NO) and smoke opacity diminish; however, carbon dioxide (CO₂), carbon monoxide, and hydrocarbon (HC) increase for all test fuel blends in dual-fuel mode in comparison to that of a single mode at various loading conditions. It is noted that all fuel blends show better emissions over that of diesel for both the modes.     

A study of the performance,emission and combustion characteristics of a compression ignition engine using methyl ester of paradise oil–eucalyptus oil blends

The significance of this study is the complete replacement of diesel fuel with bio-fuels. For this purpose; bio-fuels, namely, methyl ester of paradise oil and eucalyptus oil were chosen and used as fuel in the form of blends. Various proportions of paradise oil and eucalyptus oil are prepared on a volume basis and used as fuels in a single cylinder, four-stroke DI diesel engine, to study the performance and emission characteristics of these fuels. In the present investigation a methyl ester derived from paradise oil is considered as an ignition improver. The results show a 49% reduction in smoke, 34.5% reduction in HC emissions and a 37% reduction in CO emissions for the Me50–Eu50 blend with a 2.7% increase in NO_x emission at full load. There was a 2.4% increase in brake thermal efficiency for the Me50–Eu50 blend at full load. The combustion characteristics of Me50–Eu50 blend are comparable with those of diesel.     

Emission characteristics of jatropha oil blends using waste wood producer gas

This paper reports about the release qualities of preheated jatropha oil mixes alongside producer gas from waste wood pieces of babul in double-fuel direct injection diesel motor. Jatropha oils were inspected in both individual and double-fuel modes at a consistent gas stream rate of 21.69 kg/h at all loading conditions. From the results it might be inferred that oxides of nitrogen and smoke emission decrease although carbon dioxide (CO₂), carbon monoxide (CO), and hydrocarbon (HC) increase for all test fuels in double-fuel operation contrasted with that of a single mode at diverse loading conditions. All fuel blends show preferable emissions over that of diesel.     

Experimental investigations of performance and emissions of Karanja oil and its blends in a single cylinder agricultural diesel engine

An experimental investigation has been carried out to analyze the performance and emission characteristics of a compression ignition engine fuelled with Karanja oil and its blends (10%, 20%, 50% and 75%) vis-a-vis mineral diesel. The effect of temperature on the viscosity of Karanja oil has also been investigated. Fuel preheating in the experiments – for reducing viscosity of Karanja oil and blends has been done by a specially designed heat exchanger, which utilizes waste heat from exhaust gases. A series of engine tests, with and without preheating/pre-conditioning have been conducted using each of the above fuel blends for comparative performance evaluation. The performance parameters evaluated include thermal efficiency, brake specific fuel consumption (BSFC), brake specific energy consumption (BSEC), and exhaust gas temperature whereas exhaust emissions include mass emissions of CO, HC, NO and smoke opacity. These parameters were evaluated in a single cylinder compression ignition engine typically used in agriculture sector of developing countries. The results of the experiment in each case were compared with baseline data of mineral diesel. Significant improvements have been observed in the performance parameters of the engine as well as exhaust emissions, when lower blends of Karanja oil were used with preheating and also without preheating. The gaseous emission of oxide of nitrogen from all blends with and with out preheating are lower than mineral diesel at all engine loads. Karanja oil blends with diesel (up to 50% v/v) without preheating as well as with preheating can replace diesel for operating the CI engines giving lower emissions and improved engine performance.     

A study on the performance and emission of a diesel engine fueled with Jatropha biodiesel oil and its blends

Biodiesel either in neat form or as a mixture with diesel fuel is widely investigated to solve the twin problem of depletion of fossil fuels and environmental degradation. The main objective of the present study is to compare performance, emission and combustion characteristics of biodiesel derived from non edible Jatropha oil in a dual fuel diesel engine with base line results of diesel fuel. The performance parameters evaluated were: brake thermal efficiency, brake specific fuel consumption, power output. As a part of combustion study, in-cylinder pressure, rate of pressure rise and heat release rates were evaluated. The emission parameters such as carbon monoxide, carbon dioxide, un-burnt hydrocarbon, oxides of nitrogen and smoke opacity with the different fuels were also measured and compared with base line results. The different properties of Jatropha oil after transestrification were within acceptable limits of standards as set by many countries. The brake thermal efficiency of Jatropha methyl ester and its blends with diesel were lower than diesel and brake specific energy consumption was found to be higher. However, HC, CO and CO₂ and smoke were found to be lower with Jatropha biodiesel fuel. NO_x emissions on Jatropha biodiesel and its blend were higher than Diesel. The results from the experiments suggest that biodiesel derived from non edible oil like Jatropha could be a good substitute to diesel fuel in diesel engine in the near future as far as decentralized energy production is concerned. In view of comparable engine performance and reduction in most of the engine emissions, it can be concluded and biodiesel derived from Jatropha and its blends could be used in a conventional diesel engine without any modification.     

The effect of biodiesel fuel obtained from waste frying oil on direct injection diesel engine performance and exhaust emissions

In this study, usage of methyl ester obtained from waste frying oil (WFO) is examined as an experimental material. A reactor was designed and installed for production of methyl ester from this kind of oil. Physical and chemical properties of methyl ester were determined in the laboratory. The methyl ester was tested in a diesel engine with turbocharged, four cylinders and direct injection. Gathered results were compared with No. 2 diesel fuel. Engine tests results obtained with the aim of comparison from the measures of torque, power; specific fuel consumptions are nearly the same. In addition, amount of emission such as CO, CO₂, NO_x, and smoke darkness of waste frying oils are less than No. 2 diesel fuel.     

Emission analysis of the effect of carbon nanowires in biodiesel–ethanol blends

The present work is dedicated to study of diesel–biodiesel–ethanol blends in a diesel engine using addition of various concentrations of carbon nanowires. Algae oil from microalgae has the potential to become a sustainable fuel source as biodiesel. The Neochloris oleoabundans algal oil was extracted by mechanical extraction method. The transesterification reaction of algal oil with methanol and base catalyst was used for the production of biodiesel. Experimental investigation results were studied for various parameters, such as exhaust emission of carbon monoxide, hydrocarbon, oxides of nitrogen gases, smoke, and carbon dioxide.     

Performance,emission and combustion characteristics of a variable compression ratio engine using methyl esters of waste cooking oil and diesel blends

The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio multi fuel engine when fueled with waste cooking oil methyl ester and its 20%, 40%, 60% and 80% blends with diesel (on a volume basis) are investigated and compared with standard diesel. The suitability of waste cooking oil methyl ester as a biofuel has been established in this study. Bio diesel produced from waste sun flower oil by transesterification process has been used in this study. Experiment has been conducted at a fixed engine speed of 1500 rpm, 50% load and at compression ratios of 18:1, 19:1, 20:1, 21:1 and 22:1. The impact of compression ratio on fuel consumption, combustion pressures and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for waste cooking oil methyl ester when compared to that of diesel. The brake thermal efficiency at 50% load for waste cooking oil methyl ester blends and diesel has been calculated and the blend B40 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions.