A theoretical study on Brønsted acidity of WO3 clusters supported on metal oxide supports by “paired interacting orbitals” (PIO) analysis

Ammonia adsorption on Brønsted acid sites of WO₃ cluster supported on metal oxide supports: SnO₂, ZrO₂, and TiO₂, is analyzed by PIO analysis. We employed (HO)(WO₃)₄(H) and (HO)(WO₃)₉(H) on (SnO₂)₁₂, (ZrO₂)₁₂, and (TiO₂)₁₂, respectively, as supported Brønsted acid models and examined two types of Brønsted acid sites, an edge type and a face type. We estimated ammonia adsorption strength by total overlap population (∑OP) of all PIOs between the Brønsted acid site and NH₃. The order of acidity (∑OP) of each model is as follows: edge type: SnO₂, 0.0096 > ZrO₂, 0.0048 > TiO₂, −0.0001  face type: ZrO₂, −0.0759 > TiO₂, −0.0761 > SnO₂, −0.0867. The edge type adsorption is far stronger than the face type one. This order in the edge type coincides with the experimental results. The reason of these results is explained by the difference of the influence of oxygen atoms sitting near the N atom of NH₃.     

Chemical deactivation of V2O5/WO3–TiO2 SCR catalysts by additives and impurities from fuels, lubrication oils and urea solution: Part II. Characterization study of the effect of alkali and alkaline earth metals

A characterization study on a practice-oriented V₂O₅/WO₃–TiO₂ SCR catalyst deactivated by Ca and K, respectively, was carried out using NH₃-TPD, DRIFT spectroscopy, and XPS as well as theoretical DFT calculations. It was found from NH₃-TPD experiments that strongly basic elements like K or Ca drastically affect the acidity of the catalysts. Detailed DRIFT spectroscopy experiments revealed that these poisoning agents mostly interact with the Brønsted acid sites of the V₂O₅ active phase, thus affecting the NH₃ adsorption. Moreover, these experiments also indicated that the V⁵⁺ = O sites are much less reactive on the poisoned catalysts. XPS investigations of the O 1s binding energies showed that the oxygen atoms of the V⁵⁺ = O sites are affected by the presence of the poisoning agents. Based on these results and on DFT calculations with model clusters of the vanadia surface, the poisoning mechanism is explained by the stabilization of the non atomic holes of the (0 1 0) V₂O₅ phase as a result of the deactivation element. Consequently, V–OH Brønsted acid sites and V⁵⁺ = O sites are inhibited, which are both of crucial importance in the SCR process. The deactivation model also gives an explanation to the very low concentrations of potassium needed to deactivate the SCR catalyst, since one metal atom sitting on such a non-atomic hole site deactivates up to four active vanadium centers.     

Catalytic activity of Pd loaded on WO3/Al2O3 for NO–CH4–O2 in the presence of water vapor

Pd loaded on various kinds of monolayer supports was applied for selective reduction of NO by methane in the presence of O₂ and water vapor. Pd/WO₃/Al₂O₃ exhibited the highest conversion of NO to N₂ among Pd loaded monolayer supports. The catalyst was relatively tolerant and reversible upon the exposure of water vapor. This is due to the enhanced amount of Brønsted acid sites under the moisture as evidenced by the IR measurement of adsorbed pyridine. The Brønsted acid sites generated on WO₃/Al₂O₃ support were required to give the dispersed Pd species, similar to on the zeolite.     

Highly dispersed NiW/γ-Al2O3 catalyst prepared by hydrothermal deposition method

This article describes a novel hydrothermal deposition method for preparing highly dispersed NiW/γ-Al₂O₃ catalysts and demonstrates its advantages over the conventional impregnation method. Via the hydrothermal precipitation reactions between sodium tungstate and hydrochloric acid and between nickel nitrate and urea, respectively, the active species W and Ni were deposited on γ-Al₂O₃. In the hydrothermal deposition of WO₃, a surfactant hexadecyltrimethyl ammonium bromide (CTAB) was used to prevent the aggregation of WO₃. The characterization results obtained by means of X-ray photoelectron spectroscopy (XPS), N₂ adsorption and high-resolution transmission electron microscopy (HRTEM) measurements showed that compared with the catalyst prepared by the conventional impregnation method, the catalyst with the same metal contents prepared by the hydrothermal deposition had much higher W and Ni dispersion, higher specific surface area, larger pore volume, the significantly decreased slab length and slightly increased stacking degree of sulfided W species, leading to the significantly enhanced dibenzothiophene (DBT) hydrodesulfurization (HDS) activity. The DBT HDS assessment results also revealed that the catalyst containing 17.7 wt% WO₃ and 2.4 wt% NiO prepared by the hydrothermal deposition method had the similar DBT HDS activity as a commercial NiW/γ-Al₂O₃ catalyst containing 23 wt% WO₃ and 2.6 wt% NiO, resulting in the greatly decreased amount of active metals for achieving the same HDS activity.     

Ammonia activation over catalysts for the selective catalytic reduction of NOx and the selective catalytic oxidation of NH3. An FT-IR study

The adsorption and transformation of ammonia over V₂O₅, V₂O₅/TiO₂, V₂O₅-WO₃/TiO₂ and CuO/TiO₂ systems has been investigated by FT-IR spectroscopy. In all cases ammonia is first coordinated over Lewis acid sites and later undergoes hydrogen abstraction giving rise either to NH₂ amide species or to its dimeric form N₂H₄, hydrazine. Other species, tentatively identified as imide NH, nitroxyl HNO, nitrogen anions N₂⁻ and azide anions N₃⁻ are further observed over CuO/TiO₂. The comparison of the infrared spectra of the species arising from both NH₃ and N₂H₄ adsorbed over CuO/TiO₂ strongly suggest that N₂H₄ is an intermediate in NH₃ oxidation over this active selective catalytic reduction (SCR) and selective catalytic oxidation (SCO) catalysts. This implies that ammonia is activated in the form of NH₂ species for both SCR and SCO, and it can later dimerize. Ammonia protonation to ammonium ion is detected over V₂O₅-based systems, but not over CuO/TiO₂, in spite of the high SCR and SCO activity of this catalyst. Consequently Brönsted acidity is not necessary for the SCR activity.     

WO3/TiO2-ZrO2脱硝催化剂制备及其NH3活化机理

采用共沉淀法制备了WO₃/TiO₂-ZrO₂脱硝催化剂,并用固定床反应器进行活性评价,采用BET、XRD、TPD、氨气吸附漫反射FT-IR进行表征。结果显示,ZrO₂掺杂增强了TiO₂的Lewis酸性;负载WO₃之后,位于3.1~1.7 nm之间孔隙的稳定性显著增强;NH₃的吸附与活化分别由TiO₂-ZrO₂载体和WO₃完成;WO₃中W元素强大的电负性,促进了NH₃的N-H键由共价键向离子键过渡,进而导致了NH₃的活化。脱硝活性结果显示:当WO₃含量为9%(质量)时,催化剂脱硝活性最高,并在320~420℃的温度窗口保持94%以上。(9%)WO₃/TiO₂-ZrO₂具有更加稳定的孔隙结构(4.4~1.7 nm),表面Brønsted酸中心数量增加,Lewis酸中心的强度和酸量增加的幅度最大,NH₃-SCR过程中的活性中间产物NH₂的吸收峰更加明显,这些特征可能是其脱硝活性最好的原因。     

The role of acidity in the decomposition of 1,2-dichlorobenzene over TiO2-based V2O5/WO3 catalysts

The influence of Lewis and Brønsted acid sites on the performance of V₂O₅/TiO₂ and V₂O₅–WO₃/TiO₂ catalysts in the total oxidation of o-dichlorobenzene was investigated. Catalytic activity of these materials resulted strongly affected by their acidic properties. The presence of Brønsted acid sites significantly increases the o-DCB conversion but also leads to the uncompleted degradation of chlorinated compounds, promoting the formation of partial oxidation products, as dichloromaleic anhydride. On the contrary, Lewis acid sites, acting as absorbing sites, promote the further oxidation of intermediates to CO and CO₂, without any by-products desorption.

Furthermore, the presence of water in the feed-stream was proven to decrease o-DCB conversion but also to play a positive role on process selectivity, increasing COx production. Plausible reasons for this effect are the reduction of Brønsted acid sites and the hydrolysis of anhydride during wet tests.     

TiO2-SiO2 and V2O5/TiO2-SiO2 catalyst: Physico-chemical characteristics and catalytic behavior in selective catalytic reduction of NO by NH3

TiO₂-SiO₂ with various compositions prepared by the coprecipitation method and vanadia loaded on TiO₂-SiO₂ were investigated with respect to their physico-chemical characteristics and catalytic behavior in SCR of NO by NH₃ and in the undesired oxidation of SO₂ to SO₃, using BET, XRD, XPS, NH₃-TPD, acidity measurement by the titration method and activity test. TiO₂-SiO₂, compared with pure TiO₂, exhibits a remarkably stronger acidity, a higher BET surface area, a lower crystallinity of anatase titania and results in allowing a good thermal stability and a higher vanadia dispersion on the support up to high loadings of 15 wt% V₂O₅. The SCR activity and N₂ selectivity are found to be more excellent over vanadia loaded on TiO₂-SiO₂ with 10–20 mol% of SiO₂ than over that on pure TiO₂, and this is considered to be associated with highly dispersed vanadia on the supports and large amounts of NH₃ adsorbed on the catalysts. With increasing SiO₂ content, the remarkable activity decrease in the oxidation of SO₂ to SO₃, favorable for industrial SCR catalysts, was also observed, strongly depending on the existence of vanadium species of the oxidation state close to V⁴⁺ on TiO₂-SiO₂, while V⁵⁺ exists on TiO₂, according to XPS. It is concluded that vanadia loaded on Ti-rich TiO₂-SiO₂ with low SiO₂ content is suitable as SCR catalysts for sulfur-containing exhaust gases due to showing not only the excellent de-NO_x activity but also the low SO₂ oxidation performance.     

Catalytic activation of ceramic filter elements for combined particle separation, NOx removal and VOC total oxidation

The development of a catalytically active filter element for combined particle separation and NO_x removal or VOC total oxidation, respectively, is presented. For NO_x removal by selective catalytic reduction (SCR) a catalytic coating based on a TiO₂–V₂O₅–WO₃ catalyst system was developed on a ceramic filter element. Different TiO₂ sols of tailor-made mean particle size between 40 and 190 nm were prepared by the sol–gel process and used for the impregnation of filter element cylinders by the incipient wetness technique. The obtained TiO₂-impregnated sintered filter element cylinders exhibit BET surface areas in the range between 0.5 and 1.3 m²/g. Selected TiO₂-impregnated filter element cylinders of high BET surface area were catalytically activated by impregnation with a V₂O₅ and WO₃ precursor solution. The obtained catalytic filter element cylinders show high SCR activity leading to 96% NO conversion at 300 °C, a filtration velocity of 2 cm/s and an NO inlet concentration of 500 vol.-ppm. The corresponding differential pressures fulfill the requirements for typical hot gas filtration applications. For VOC total oxidation, a TiO₂-impregnated filter element support was catalytically activated with a Pt/V₂O₅ system. Complete oxidation of propene with 100% selectivity to CO₂ was achieved at 300 °C, a filtration velocity of 2 cm/s and a propene inlet concentration of 300 vol.-ppm.     

制备方法对V_2O_5-WO_3/TiO_2选择性催化还原催化剂性能的影响

采用共沉淀法、溶胶-凝胶法和浸渍法制备了V2O5质量分数4%和WO3质量分数6%的V2O5-WO3/TiO2选择性催化还原催化剂,对比了3种方法制备的催化剂选择性催化还原NO性能。采用X射线衍射、热重、N2吸附-脱附和程序升温还原等对制备的V2O5-WO3/Ti O2催化剂的结构和性质进行表征,结果表明,共沉淀法制备的V2O5-WO3/TiO2催化剂具有更好的选择性催化还原NO活性和更大的比表面积,影响共沉淀法选择性催化还原NO活性的主要因素是催化剂的热稳定性、表面羟基数量、比表面积、粒径分布以及V、W与Ti之间的内在作用。     

The preparation of coupled WO3/TiO2 photocatalyst by ball milling

The coupled photocatalyst WO₃/TiO₂ is prepared by ball milling by doping WO₃ into TiO₂ and using H₂O solution as disperser. The coupled photocatalyst WO₃/TiO₂ is characterized by UV–VIS diffuse reflection spectrum, X-ray photoelectron spectroscopy (XPS), X-ray powder diffraction (XRD) and Transmission electron microscopy (TEM). The results show that the optimum percentage of WO₃ doped is 3% and that the photocatalytic activity of the coupled WO₃/TiO₂ photocatalyst is much higher than that of TiO₂ and WO₃–TiO₂ with no ball milling. Compared with TiO₂, the photoexcited wavelength range of the WO₃/TiO₂ photocatalyst red-shifts about 50 nm, and the light absorption intensity is also improved. The crystal phase of TiO₂ is not changed and new crystal phases are not found during the process of ball milling. WO₃ and TiO₂ coupled highly, forming the WO₃/TiO₂ photocatalyst. The increased photocatalytic activity of the coupled photocatalyst may be attributed to the enhance charge separation efficiency and the extend wavelength range of photoexcitation.     

Inhibition effect of H2O on V2O5/AC catalyst for catalytic reduction of NO with NH3 at low temperature

The inhibition effect of H₂O on V₂O₅/AC catalyst for NO reduction with NH₃ is studied at temperatures up to 250 °C through TPD, elemental analyses, temperature-programmed surface reaction (TPSR) and FT-IR analyses. The results show that H₂O does not reduce NO and NH₃ adsorption on V₂O₅/AC catalyst surface, but promotes NH₃ adsorption due to increases in Brønsted acid sites. Many kinds of NH₃ forms present on the catalyst surface, but only NH₄⁺ on Brønsted acid sites and a small portion of NH₃ on Lewis acid sites are reactive with NO at 250 °C or below, and most of the NH₃ on Lewis acid sites does not react with NO, regardless the presence of H₂O in the feed gas. H₂O inhibits the SCR reaction between the NH₃ on the Lewis acid sites and NO, and the inhibition effect increases with increasing H₂O content. The inhibition effect is reversible and H₂O does not poison the V₂O₅/AC catalyst.     

Activity and acidity of Nb2O5-MoO3 and Nb2O5-WO3 in the Friedel-Crafts alkylation

Nb₂O₅ loaded on the supports and mixed with oxides was studied to investigate the activity and acidity for Friedel-Crafts benzylation of anisole. From the study on the loaded catalysts, a preliminary conclusion for the selection of metal oxide was obtained; namely, such an acidic oxide as silica was suitable for the support of Nb₂O₅. Then, MoO₃ and WO₃ were mixed with Nb₂O₅, and prominent high catalytic activity and acidities were observed. Both oxides of Nb₂O₅-MoO₃ and Nb₂O₅-WO₃ showed almost similar behavior with respect to characterization and catalytic activity. Surface area increased, X-ray diffraction (XRD) and Raman bands were lost, acid sites, both Brønsted and Lewis characters generated, and surface acid site density was as high as 2–4 nm⁻². The acid sites were generated on the amorphous metal oxides consisting of Nb and Mo or W oxides, different in nature from those of Nb₂O₅ calcined and un-calcined, and active for Friedel-Crafts benzylation.     

Catalytic performance of a novel ceramic-supported vanadium oxide catalyst for NO reduction with NH3

A novel TiO₂/Al₂O₃/cordierite honeycomb-supported V₂O₅–MoO₃–WO₃ monolithic catalyst was studied for the selective reduction of NO with NH₃. The effects of reaction temperature, space velocity, NH₃/NO ratio and oxygen content on SCR activity were evaluated. Two other V₂O₅–MoO₃–WO₃ monolithic catalysts supported on Al₂O₃/cordierite honeycomb or TiO₂/cordierite honeycomb support, two types of pellet catalysts supported on TiO₂/Al₂O₃ or Al₂O₃, as well as three types of pellet catalysts V₂O₅–MoO₃–WO₃–Al₂O₃ and V₂O₅–MoO₃–WO₃–TiO₂ were tested for comparison. The experiment results show that this catalyst has a higher catalytic activity for SCR with comparison to others. The results of characterization show, the preparation method of this catalyst can give rise to a higher BET surface area and pore volume, which is strongly related with the highly active performance of this catalyst. At the same time, the function of the combined carrier of TiO₂/Al₂O₃ cannot be excluded.     

Solid acidity of metal oxide monolayer and its role in catalytic reactions

Such metal oxide as SO₄²⁻, MoO₃, WO₃, and V₂O₅ spread readily on supports like SnO₂, ZrO₂, and TiO₂ due to the different properties between acid and base oxides to generate the acid site on the monolayer. Number, strength, and structure of the acid site were characterized by temperature-programmed desorption (TPD) of ammonia principally, together with various physico-chemical techniques, and its role for catalytic reactions was studied. Approximately, one to two acid sites were stabilized on 1 nm² of the surface, which consisted of four to eight metal atoms. The limit in surface acid site density was estimated on the monolayer based on the concept of solid acidity on zeolites. Sequence of the metal oxide to show the strong acidity was, SO₄²⁻>WO₃>MoO₃>V₂O₅, and for the support oxide to accommodate the monolayer, SnO₂>ZrO₂>TiO₂>Al₂O₃. From these combinations, the metal oxide monolayer to show the adequate strength of acid site could be selected. Brønsted acidity was observed often, however, the Lewis acidity was prevailing on the reduced vanadium oxide. The structure of acid site, Brønsted or Lewis acid site, thus depended on the oxidation state. Relationship of the profile of solid acidity with various catalytic activities was explained. The solid acid site on the monolayer will possibly be applied to environment friendly technologies.     

Nb2O5-supported WO3: a comparative study with WO3/Al2O3

WO₃/Nb₂O₅-supported samples prepared by impregnation are characterised by X-ray diffraction (XRD), Raman spectroscopy and X-ray absorption spectroscopy (XAS) at the W–L₃ absorption edge, as well as temperature programmed reduction (TPR) and FT-IR monitoring of pyridine adsorption. Results are compared with those obtained for WO₃/Al₂O₃ samples prepared in the same conditions, showing that niobia is able to disperse tungsta better than alumina does. Formation of a crystalline WO₃ needs larger tungsten contents on niobia than on alumina, since tungsten solution into niobia is easier than into alumina. Raman and XAS spectra recorded under ambient conditions suggest that similar WO_x species are formed on both supports at tungsten contents 0.5–1 theoretical monolayers; however, TPR results for the low tungsten loaded samples indicate that, when reduction starts (always at temperatures higher than 700 K under H₂/Ar flow) there is a larger concentration of tetrahedral [WO₄] species on alumina, than on niobia. Samples with low tungsten loading have been tested in isopropanol decomposition and ethylene oxidation, following both processes by FT-IR of adsorbed species up to 673 K. Results show that adsorption of ethylene on WO₃/Nb₂O₅ yields acetaldehyde and acetate at 473 K, while this adsorption is non-reactive either on the supports or on WO₃/Al₂O₃. Isopropanol adsorbs dissociatively on both supports, leading to acetone and propene formation on tungsta–niobia, but only propene on tungsta–alumina, probably due to the larger reducibility of the tungsten-containing phases.     

Regeneration of commercial SCR catalysts by washing and sulphation: effect of sulphate groups on the activity

The use of bio-fuels is becoming more important because of the environmental benefits associated with these fuels. Deactivation of SCR catalysts applied in bio-fuel plants is a major problem due to the high potassium content of bio-fuels and therefore, great potential lies in finding regeneration processes that can be used commercially. Exposing the catalyst surface to sulphate groups generated by SO₂ or H₂SO₄ is a promising way to rejuvenate the initial activity of the catalyst. The chemical stability of the sulphate groups was investigated by the interaction of the SCR reactant gases with the sulphate-promoted catalysts. Sulphate ions deposited on the surface of the TiO₂/V₂O₅/WO₃ were thermally stable at 420°C. The introduced sulphate groups were chemically unstable when the catalyst was treated with the SCR reactants at 400°C, but were chemically stable when the catalyst was exposed for the SCR reactants at 350°C. Sulphation after water treatment provided more chemically stable surface sulphate groups at 400°C. The presence of sulphate groups enhanced the number and the strength of the surface acid sites. The amount of ammonia bound to the Brønsted acid sites decreased with the potassium content of the catalyst while the amount of ammonia adsorbed on the Lewis acid sites was almost unaffected. Since potassium both retarded the redox potential of the surface vanadia species and decreased the amount of ammonia bound to the Brønsted acid sites, it is important to wash the strongly deactivated catalyst before sulphation.     

Preparation and characterization of surface bond-conjugated TiO2/SiO2 and photocatalysis for azo dyes

Surface bond-conjugated TiO₂/SiO₂ was prepared by means of the impregnation method. Based on the results of XRD, FTIR, XPS and BET measurements, the growth of titania (predominantly anatase) on the silica substrate seems to occur by anchoring of the TiO₂ phase through Ti–O–Si cross-linking bonds. The structure model of TiO₂/SiO₂ was proposed. Compared to B–TiO₂, the most efficient catalyst is 30 wt.% TiO₂/SiO₂ (Ims30), which showed three times higher photoactivity for the degradation of reactive 15 (R15). In addition, the catalyst had a higher photoactivity on a silica of smaller particle size than on the silica of larger particles. Silica gel plays the basic role of dispersion and support for power TiO₂. The isoelectric point of the catalyst was 3.0 pH units by the measurement of zeta-potential, indicating the presence of the surface acidity of the catalyst. The photodegradation and the adsorption of R15 and cationic blue X-GRL (CBX) were investigated with the change of initial aqueous pH.     

Copper-impregnated Al–Ce-pillared clay for selective catalytic reduction of NO by C3H6

The selective catalytic reduction (SCR) of NO by hydrocarbon is an efficient way to remove NO emission from lean-burn gasoline and diesel exhaust. In this paper, a thermally and hydrothermally stable Al–Ce-pillared clay (Al–Ce-PILC) was synthesized and then modified by SO₄²⁻, whose surface area and average pore diameter calcined at 773 K were 161 m²/g and 12.15 nm, respectively. Copper-impregnated Al–Ce-pillared clay catalyst (Cu/SO₄²⁻/Al–Ce-PILC) was applied for the SCR of NO by C₃H₆ in the presence of oxygen. The catalyst 2 wt% Cu/SO₄²⁻/Al–Ce-PILC showed good performance over a broad range of temperature, its maximum conversion of NO was 56% at 623 K and remained as high as 22% at 973 K. Furthermore, the presence of 10% water slightly decreased its activity, and this effect was reversible following the removal of water from the feed. Py-IR results showed SO₄²⁻ modification greatly enhanced the number and strength of Brönsted acidity on the surface of Cu/SO₄²⁻/Al–Ce-PILC, which played a vital role in the improvement of NO conversion. TPR and XPS results indicated that both Cu⁺ and isolated Cu²⁺ species existed on the optimal catalyst, mainly Cu⁺, as Cu content increased to 5 wt%, another species CuO aggregates which facilitated the combustion of C₃H₆ were formed.     

Evaluation of V2O5–WO3–TiO2 and alternative SCR catalysts in the abatement of VOCs

Two different commercial SCR catalysts belonging to the V₂O₅–WO₃–TiO₂ system, and different alternative catalysts based on Mn, Fe, Cr, Al and Ti oxides have been tested in the conversion of VOCs in excess oxygen in a temperature range typical of the SCR process (500–700 K). Propane, propene, isopropanol, acetone, 2-chloropropane and 1,2-dichlorobenzene have been fed with excess oxygen and helium. The industrial catalysts are poorly active in the conversion of propane, giving mainly rise to propene by oxy-dehydrogenation. The conversion of propene is higher with CO as the predominant product. In any case, the oxidation activity depends on the vanadium content of the catalyst. Isopropanol is mainly converted into acetone and propene, while acetone is burnt predominantly to CO. Mn- and Fe- containing systems are definitely more active in the conversion of hydrocarbons and oxygenates, giving rise almost exclusively to CO₂. 2-Chloropropane is selectively dehydrochlorinated to propene and HCl starting from 350 K, propene being later burnt to CO on the industrial V₂O₅–WO₃–TiO₂ catalysts, whose combustion activity is, apparently, not affected by chlorine. On the contrary, chlorine strongly affects the behavior of Mn-based catalysts, that are active in the dehydrochlorination of 2-chloropropane, but are simultaneously deactivated with respect to their combustion catalytic activity. The conversion of 1,2-dichlorobenzene gives rise to important amounts of heavy products in our experimental conditions with relatively high reactant concentration.