共查询到20条相似文献,搜索用时 78 毫秒
1.
采用Ⅰ-DEAS软件对某架空索道线路支架建立一个完整的动态分析模型,通过模态分析,计算出其前10阶模态频率和对应的主振型,为架空索道线路支架的设计和使用提供了有力的技术支持。 相似文献
2.
3.
一、前言 应用电子计算机进行架空索道的线路纵断面设计,目前普遍采取的计算步骤是:首先按钢绳对支架的安全靠贴要求确定所需的支架标高,然后计算各支架的有关几何和力学参数。这种计算程序的不足之处在于,对于线路要跨越某些有要求的尺寸界限,必须在上 相似文献
4.
5.
6.
驱动机是架空索道的重要组成部分,其结构的正确设计对于索道的正常运转具有十分重要的意义。当设计长距离或起终点高差很大的架空索道时,常常需要将整个线路划分成若干区段,而每个区段允许的高差和距离是受地形、运输能力以及设备性能等条件限制的。设计具有多个传动区段的索道线路时,一般都采用单独的驱动机传动各个区段,但也有用一台驱 相似文献
7.
1.引言在单线循环式架空索道上,为了防止负荷超过材料所允许的最大强度极限和牵引索意外地损坏,有必要限制索道支架及托索轮上的负载在允许的最小和最大范围内。本文首先对传统的计算支架负荷的近似方法进行讨论,然后再结合现有的索道计算程序介绍一种易用程序 相似文献
8.
9.
我国架空索道目前尚没有一套完善的运行监视装置,如果索道在运行中发生“卡斗”则不能及时发现,而索道仍继续运行,以致造成严重事故。我们在生产实际中,观察驱动机的负荷电流变化以便判断线路是否发生卡斗事故,因此,探索架空索道负荷电流的变化规律,用以监视索道的运行状态,从而预防或减少由于卡斗而造成的事故。 相似文献
10.
介绍了模态分析的基本原理,并以架空索道塔架为例,运用ANSYS软件对其进行结构模态有限元分析,计算得出该塔架的前10阶模态频率及相应的主振型,为其设计和使用提供了必要的依据. 相似文献
11.
In a recent paper, the Ritz method with simple algebraic polynomials as trial functions was used to obtain an eigenvalue equation for the free vibration of a class of homogeneous solids with cavities. The method presented is here extended to the study of a class of non-homogeneous solids, in which each solid is composed of a number of isotropic layers with different material properties. The Cartesian coordinate system is used to describe the geometry of the solid which is modelled by means of a segment bounded by the yz, zx and xy orthogonal coordinate planes and by two curved surfaces which are defined by fairly general polynomial expressions in the coordinates x, y and z. The surface representing the interface between two material layers in the solid is also described by a polynomial expression in the coordinates x, y and z. In order to demonstrate the accuracy of the approach, natural frequencies are given for both a two- and three-layered spherical shell and for a homogeneous hollow cylinder, as computed using the present approach, and are compared with those obtained using an exact solution. Results are then given for a number of two- and three-layered cylinders and, to demonstrate the versatility of the approach, natural frequencies are given for a five-layered cantilevered beam with a central circular hole as well as for a number of composite solids of more general shape. 相似文献
12.
13.
通过分析膨胀套在实际使用产生滑移受阻现象、卡死现象原因的实质,并在分析产生问题原因的基础上提出了改进措施即:增加导向机构。 相似文献
14.
15.
设计了磨粉机快辊轴承座的加工工艺和具体的工装夹具.利用卧式加工中心加工磨粉机快辊轴承座,辅以能够高效快速夹紧的夹具,既可以保证加工精度,又能够提高加工效率. 相似文献
16.
一种涡旋压缩机径向随变机构的设计 总被引:1,自引:0,他引:1
详细介绍了运用随变原理设计的一种新型径向密封机构的结构特点,工作原理及主要参数的确定方法,该机构可补偿由于涡旋体加工精度不高而造成的功率损失,适用于涡旋压缩机的批量生产。 相似文献
17.
本文以某些积算和双笔记录仪产品为例说明由于仪表功能设计的不合理或选型不当,影响了仪表的正常使用,制造厂和用户应关注这类问题。 相似文献
18.
V. P. Dragunov E. G. Kostsov 《Optoelectronics, Instrumentation and Data Processing》2009,45(3):234-242
Specific features of operation of one- and two-capacitor microelectromechanical converters (MEMC) of energy of mechanical microscopic vibrations into electric energy with a modulated electrode-gap magnitude and with allowance for the mutual influence of electrical and elastic forces are analyzed, and the characteristics of these two devices are compared. The main factors restricting the increase in MEMC power are demonstrated to be the effects of “collapsing” and the condition of conservation of positive rigidity of the system. Expressions for estimating the limiting MEMC parameters are derived. The possibility of electrical energy generation in the presence of “real“ sources of wide-spectrum microscopic vibrations is considered. 相似文献
19.
针对目前市场对工业设计人才的需求,本文论述了我校在工业设计教育方面的改革措施,着重介绍了我校工业设计教育在软件和硬件方面所进行的一系列的改革。 相似文献