Preparation and photocatalytic properties of HLaNb2O7/(Pt,TiO2) perovskite intercalated nanomaterial

A novel perovskite intercalated nanomaterial HLaNb₂O₇/(Pt, TiO₂) is fabricated by successive intercalated reaction of HLaNb₂O₇ with [Pt(NH₃)₄]Cl₂ aqueous solution, n-C₆H₁₃NH₂/C₂H₅OH organic solution and acidic TiO₂ colloid solution, followed by ultraviolet light irradiation. The gallery height and the band gap energy of HLaNb₂O₇/(Pt, TiO₂) is less than 0.6 nm and 3.14 eV, respectively. The photocatalytic activity of HLaNb₂O₇/TiO₂ is superior to that of unsupported TiO₂ and is enhanced by the co-incorporation of Pt. The photocatalytic hydrogen evolution based on HLaNb₂O₇/(Pt, TiO₂) is 240 cm³ h⁻¹ g⁻¹ using methanol as a sacrificial agent under irradiation with wavelength more than 290 nm from a 100-W mercury lamp. High photocatalytic activity of HLaNb₂O₇/(Pt, TiO₂) may be due to the host with rare earth La element and perovskite structure, the quantum size effect of intercalated semiconductor and the coupling effect between host and guest.     

CuCr2O4/TiO2 heterojunction for photocatalytic H2 evolution under simulated sunlight irradiation

CuCr₂O₄/TiO₂ heterojunction has been successfully synthesized via a facile citric acid (CA)-assisted sol-gel method. Techniques of X-ray diffraction (XRD), transmission electron microscopy (TEM), and UV-vis diffuse reflectance spectrum (UV-vis DRS) have been employed to characterize the as-synthesized nanocomposites. Furthermore, photocatalytic activities of the as-obtained nanocomposites have been evaluated based on the H₂ evolution from oxalic acid solution under simulated sunlight irradiation. Factors such as CuCr₂O₄ to TiO₂ molar ratio in the composites, calcination temperature, photocatalyst mass concentration, and initial oxalic acid concentration affecting the photocatalytic hydrogen producing have been studied in detail. The results showed that the nanocomposite of CuCr₂O₄/TiO₂ is more efficient than their single part of CuCr₂O₄ or TiO₂ in producing hydrogen. The optimized composition of the nanocomposites has been found to be CuCr₂O₄·0.7TiO₂. And the optimized calcination temperature and photocatalyst mass concentration are 500 °C and 0.8 g l⁻¹, respectively. The influence of initial oxalic acid concentration is consistent with the Langmuir model.     

Study of Pt electrode dissolution in H2O2-containing H2SO4 solution using an electrochemical quartz crystal microbalance

Pt electrode dissolution has been investigated using an electrochemical quartz crystal microbalance (EQCM) in H₂O₂-containing 0.5 mol dm⁻³ H₂SO₄. The Pt electrode weight-loss of ca. 0.4 μg cm⁻² is observed during nine potential sweeps between 0.01 and 1.36 V vs. RHE. In contrast, the Pt electrode weight-loss is negligible without H₂O₂ (<0.05 μg cm⁻²). To support the EQCM results, the weight-decrease amounts of a Pt disk electrode and amounts of Pt dissolved in the solutions were measured after similar successive potential cycles. As a result, these results agreed well with the EQCM results. Furthermore, the H₂O₂ concentration dependence of the Pt weight-decrease rate was assessed by successive potential steps. These EQCM data indicated that the increase in H₂O₂ accelerates the Pt dissolution. Based on these results, H₂O₂ is known to be a major factor contributing to the Pt dissolution.     

Synthesis of (CuIn)xCd2(1−x)S2 photocatalysts for H2 evolution under visible light by using a low-temperature hydrothermal method

A new series visible-light driven photocatalysts (CuIn)_xCd_2(1−x)S₂ was successfully synthesized by a simple and facile, low-temperature hydrothermal method. The synthesized materials were characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET) surface area measurement, X-ray photoelectron spectroscopy (XPS) and ultraviolet-visible spectroscopy (UV–Vis DRS). The results show that the morphology of the photocatalysts changes with the increase of x from 0.01 to 0.3 and their band gap can be correspondingly tuned from 2.37 eV to 2.30 eV. The (CuIn)_xCd_2(1−x)S₂ nanocomposite show highly photocatalytic activities for H₂ evolution from aqueous solutions containing sacrificial reagents, SO₃²⁻ and S²⁻ under visible light. Substantially, (CuIn)_0.05Cd_1.9S₂ with the band gap of 2.36 eV exhibits the highest photocatalytic activity even without a Pt cocatalyst (649.9 μmol/(g h)). Theoretical calculations about electronic property of the (CuIn)_xCd_2(1−x)S₂ indicate that Cu 3d and In 5s5p states should be responsible for the photocatalytic activity. Moreover, the deposition of Pt on the doping sample results in a substantial improvement in H₂ evolution than the Pt-loaded pure CdS and the amount of H₂ produced (2456 μmol/(g h)) in the Pt-loaded doping system is much higher than that of the latter (40.2 μmol/(g h)). The (CuIn)_0.05Cd_1.9S₂ nanocomposite can keep the activity for a long time due to its stability in the photocatalytic process. Therefore, the doping of CuInS₂ not only facilitates the photocatalytic activity of CdS for H₂ evolution, but also improves its stability in photocatalytic process.     

Photocatalytic activities of HLaNb2O7 prepared by polymerized complex method

HLaNb₂O₇ photocatalyst was prepared by the proton exchange reaction of KLaNb₂O₇ with diluted acid. The layered perovskite KLaNb₂O₇ has been successfully synthesized by the polymerized complex method. The product was characterized by X-ray diffraction, ultraviolet–visible spectra, scan electron microscope, TG–DSC, specific surface area, and FTIR. The layered perovskite KLaNb₂O₇ was formed at a lower calcination temperature (1000 °C, 6 h) by the polymerized complex method than a solid-state reaction method (1150 °C, 24 h). Photocatalytic decomposition of water to produce hydrogen under UV irradiation with methanol as electron donor was studied over layered perovskite HLaNb₂O₇ photocatalysts. The HLaNb₂O₇ photocatalyst prepared by the polymerized complex method showed much higher activity than that prepared by conventional solid-state reaction method.     

Fabrication of graphene/CaIn2O4 composites with enhanced photocatalytic activity from water under visible light irradiation

A series of graphene/CaIn₂O₄ composites were synthesized using a facile solvothermal method to improve the photocatalytic performance of CaIn₂O₄. The reduction of graphene oxide to graphene and the deposition of CaIn₂O₄ nanoparticles on the graphene sheets can be achieved simultaneously during the solvothermal process. The photocatalytic activities of as-prepared graphene/CaIn₂O₄ composites for hydrogen evolution from CH₃OH/H₂O solution were investigated under visible light irradiation. It was found that graphene exhibited an obvious influence on the photocatalytic activity of CaIn₂O₄. The graphene/CaIn₂O₄ composite reached a high H₂ evolution rate of 62.5 μmol h⁻¹ from CH₃OH/H₂O solution when the content of graphene was 1 wt%. Furthermore, the 1 wt% graphene/CaIn₂O₄ composite did not show deactivation for H₂ evolution for longer than 32 h. This work could provide a new insight into the fabrication of visible light driven photocatalysts with efficient and stable performance.     

Significant improvement of photocatalytic hydrogen generation rate over TiO2 with deposited CuO

TiO₂ photocatalyst with deposited CuO (CuO-TiO₂) was synthesized by the impregnation method using P25 (Degussa) as support, and exhibited high photocatalytic hydrogen generation activity from methanol/water solution. A substantial hydrogen evolution rate of 10.2 ml min⁻¹ (18,500 μmol h⁻¹ g⁻¹_catalyst) was observed over this efficient CuO-TiO₂ with optimal Cu content of 9.1 mol% from an aqueous solution containing 10 vol% methanol; this improved hydrogen generation rate is significantly higher than the reported Cu-containing TiO₂, including some Pt and Pd loaded TiO₂. Optimal Cu content of 9.1 mol% provided maximum active sites and allowed good light penetration in TiO₂. Over this efficient CuO-TiO₂, the hydrogen generation rate was accelerated by increasing the methanol concentration according to Freundlich adsorption isotherm. However, the photocatalytic hydrogen generation rate was suppressed under long time irradiation mainly due to accumulation of by-products, reduction of CuO and copper leaching, which requires further investigation.     

Enhanced photocatalytic water splitting activity of carbon-modified TiO2 composite materials synthesized by a green synthetic approach

We report a green and facile approach for the preparation of carbon-modified (C-modified) TiO₂ composite materials by hydrothermal synthesis followed by pyrolytic treatment. The resultant materials were characterized by powder X-ray diffraction (XRD), nitrogen physisorption studies, Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), diffuse reflectance spectroscopy (DRS), photoluminescence (PL) spectroscopy, and transmission electron microscopy (TEM). The photocatalytic performances of these materials were evaluated by calculating the amount of hydrogen evolved from the decomposition of water under solar simulated irradiation conditions. An improvement was achieved from no H₂ evolution at all with the bare TiO₂, to an evolution of 0.21 mL g⁻¹ h⁻¹ from a composite material modified with an optimum carbon loading of 3.62%. These results suggested that the interaction of carbon with predominantly rutile form of TiO₂ can promote shallow trapping of photogenerated electrons in the oxygen vacancies. This phenomenon consequently enhances the photocatalytic activity by minimizing charge carrier recombination, a characteristic demonstrated by fluorescence quenching of the TiO₂ emission.     

Fabrication of nano N-doped In2Ga2ZnO7 for photocatalytic hydrogen production under visible light

N-doped In₂Ga₂ZnO₇ photocatalysts were fabricated by solid state reaction route. All the prepared photocatalysts were successfully characterised by PXRD, optical absorption spectra, SEM, TEM, XPS, BET surface area and photoresponse studies. The formation of In₂Ga₂ZnO₇ was confirmed by the PXRD pattern. Optical absorption spectra showed that the visible light absorption of all the photocatalysts were enhanced by nitrogen doping. Among all the prepared photocatalysts, 1 wt% Pt loaded N-GaInZn-500 showed enhanced photocatalytic activity towards hydrogen evolution under visible light irradiation in presence of 10 vol% methanol solution as sacrificial agent. The excellent photocatalytic activity of N-GaInZn-500 is in agreement with N-content, bandgap energy, PL intensity and Surface area.     

Formation of multilayer-Eosin Y-sensitized TiO2 via Fe coupling for efficient visible-light photocatalytic hydrogen evolution

An efficient visible-light active photocatalyst of multilayer-Eosin Y-sensitized TiO₂ is prepared through linkage of Fe³⁺ between not only TiO₂ and Eosin Y but also different Eosin Y molecules to form three-dimensional polymeric dye structure. The multilayer-dye-sensitized photocatalyst is found to have high light harvesting efficiency and photocatalytic activity for hydrogen evolution under visible light irradiation (λ > 420 nm). On the optimum conditions (1:1 initial molar ratio of Eosin Y to Fe(NO₃)₃, initial 10 × 10⁻³ M Eosin Y, and 1.0 wt% Pt deposited by in situ photoreduction), its maximal apparent quantum yield for hydrogen evolution is 19.1% from aqueous triethanolamine solution (TEOA aq). The present study highlights linking between dye molecules via metal ions as a general way to develop efficient visible-light photocatalyst.     

Visible light induced hydrogen evolution on new hetero-system ZnFe2O4/SrTiO3

The physical properties and photoelectrochemical characterization of the spinel ZnFe₂O₄, elaborated by chemical route, have been investigated for the hydrogen production under visible light. The forbidden band is found to be 1.92 eV and the transition is indirectly allowed. The electrical conduction occurs by small polaron hopping with activation energy of 0.20 eV. p-type conductivity is evidenced from positive thermopower and cathodic photocurrent. The flat band potential (0.18 V_SCE) determined from the capacitance measurements is suitably positioned with respect to H₂O/H₂ level (−0.85 V_SCE). Hence, ZnFe₂O₄ is found to be an efficient photocatalyst for hydrogen generation under visible light. The photoactivity increases significantly when the spinel is combined with a wide band gap semiconductor. The best performance with a hydrogen rate evolution of 9.2 cm³ h⁻¹ (mg catalyst)⁻¹ occurs over the new hetero-system ZnFe₂O₄/SrTiO₃ in Na₂S₂O₃ (0.025 M) solution.     

Photocatalytic property of partially substituted Pt-intercalated layered perovskite, ASr2TaxNb3−xO10 (A=K, H; x=0, 1, 1.5, 2 and 3)

A series of layered perovskite photocatalysts, ASr₂Ta_xNb_3−xO₁₀ (A=K, H; x=0, 1, 1.5, 2 and 3), were synthesized by conventional solid-state reaction followed by an ion-exchange reaction. Pt was incorporated in the interlayer of HSr₂Ta_xNb_3−xO₁₀ by the stepwise intercalation reaction. The HSr₂Ta_xNb_3−xO₁₀ showed hydrogen production activity and the activities were greatly enhanced by Pt co-incorporating. The x value in HSr₂Ta_xNb_3−xO₁₀ had an important effect on the photocatalytic activity of the catalyst. When the x=1, the HSr₂TaNb₂O₁₀/Pt photocatalyst showed a photocatalytic activity of 208 cm³ g⁻¹ h⁻¹ hydrogen evolution rate in 10 vol% methanol solution under irradiation with wavelength more than 290 nm from a 100-W mercury lamp at 333 K. The HSr₂TaNb₂O₁₀/Pt photocatalyst exhibited much higher photocatalytic activity than the well-known TiO₂/Pt photocatalyst under the same conditions.     

Controllable O2 oxidization graphene in TiO2/graphene composite and its effect on photocatalytic hydrogen evolution

TiO₂/reduced graphene oxide composite (T-rGO) was synthesized and its performance was evaluated with photocatalytic hydrogen evolution. It was found that the hydrogen evolution rate of T-rGO increased significantly after injecting small amount of air into the vacuum pumped and UV irradiated sealed reaction cell. The IR, XPS, Raman and ESR spectra analysis indicated that the O₂^•−, which generated from the reaction of photoinduced electrons and the injected O₂ can moderately and controllably increase the oxygen groups on graphene planar of T-rGO at ambient condition. The amount of oxygen groups on graphene planar of T-rGO will affect the p-doping concentration of graphene, thus affect the p–n junction and the performance of T-rGO for photocatalytic hydrogen evolution.     

The effect of low concentrations of CO on H2 adsorption and activation on Pt/C. Part 1: In the absence of humidity

The presence of CO in the H₂-rich gas used as fuel for hydrogen fuel cells has a detrimental effect on PEMFC performance and durability at conventional operating conditions. This paper reports on an investigation of the effect of CO on H₂ activation on a fuel cell Pt/C catalyst close to typical PEMFC operating conditions using H₂-D₂ exchange as a probe reaction and to measure hydrogen surface coverage. While normally limited by equilibrium in the absence of impurities on Pt at typical fuel cell operating temperatures, the presence of ppm concentrations of CO increased the apparent activation energy (E_a) of H₂-D₂ exchange reaction (representing H₂ activation) from approximately 4.5-5.3 kcal mole⁻¹ (Bernasek and Somorjai (1975) [24], Montano et al. (2006) [25]) (in the absence of CO) to 19.3-19.7 kcal mole⁻¹ (in the presence of 10-70 ppm CO), similar to those reported by Montano et al. (2006) [25]. Calculations based on measurements indicate a CO surface coverage of approximately 0.55 ML at 80 °C in H₂ with 70 ppm CO, which coincide very well with surface science results reported by Longwitz et al. (2004) [5]. In addition, surface coverages of hydrogen in the presence of CO suggest a limiting effect on hydrogen spillover by CO. Regeneration of Pt/C at 80 °C in H₂ after CO exposure showed only a partial recovery of Pt sites. However, enough CO-free Pt sites existed to easily achieve equilibrium conversion for H₂-D₂ exchange. This paper establishes the baseline and methodology for a series of future studies where the additional effects of Nafion and humidity will be investigated.     

Visible-light-driven ZnIn2S4/CdIn2S4 composite photocatalyst with enhanced performance for photocatalytic H2 evolution

ZnIn₂S₄/CdIn₂S₄ composite photocatalysts (x = 0–1) were successfully synthesized via a hydrothermal route. Compositions of ZnIn₂S₄/CdIn₂S₄ composite photocatalysts were optimized according to the photocatalytic H₂ evolution rate. XRD patterns indicate the as-prepared samples are mixtures of hexagonal and cubic structures. FESEM and TEM images show that the as-prepared samples are composed of flower-like microspheres with wide distribution of diameter. There is obviously distinguishing distribution of Zn, Cd elements among the composite architectures. UV–vis absorption spectra of different compositions exhibit that absorption edges of ZnIn₂S₄/CdIn₂S₄ composites slightly move towards longer wavelengths with the increment of CdIn₂S₄ component. A typical time course of photocatalytic H₂ evolution from an aqueous Na₂SO₃ and Na₂S solution over unloaded and PdS-loaded ZnIn₂S₄/CdIn₂S₄ composite photocatalyst is carried out. The initial activity for H₂ evolution over 0.75 wt% PdS-loaded sample is up to 780 μmol h⁻¹. And the activity of unloaded sample also reaches 490 μmol h⁻¹ with consistent stability.     

Evaluation of nano-structured Ir0.5Mn0.5O2 as a potential cathode for intermediate temperature solid oxide fuel cell

A novel Ir_0.5Mn_0.5O₂ cathode has been synthesized by thermal decomposition of mixed H₂IrCl₆ and Mn(NO₃)₂ water solution. The Ir_0.5Mn_0.5O₂ cathode has been characterized by XRD, field emission SEM (FESEM) and AC impedance spectroscopy. XRD result shows that rutile-structured Ir_0.5Mn_0.5O₂ phase is formed by thermal decomposition of mixed H₂IrCl₆ and Mn(NO₃)₂ water solution. FESEM micrographs show that a porous structure with well-necked particles forms in the cathode after sintering at 1000 °C. The average grain size is between 20 and 30 nm. Two depressed arcs appear in the medium-frequency and low-frequency region, indicating that there are at least two different processes in the cathode reaction: charge transfer and molecular oxygen dissociation followed by surface diffusion. The minimum area specific resistance (ASR) is 0.67 Ω cm² at 800 °C. The activation energy for the total oxygen reduction reaction is 93.7 kJ mol⁻¹. The maximum power densities of the Ir_0.5Mn_0.5O₂/LSGM/Pt cell are 43.2 and 80.7 mW cm⁻² at 600 and 700 °C, respectively.     

Characterization of new heterosystem CuFeO2/SnO2 application to visible-light induced hydrogen evolution

Photo-assisted H₂ evolution has been realized over the new heterosystem CuFeO₂/SnO₂ without any noble metal and was studied in connection with some physical parameters. The delafossite CuFeO₂ has been prepared by thermal decomposition from various salts. The polarity of generated voltage is positive indicating that the materials exhibit p-type conductivity whereas the electroneutrality is achieved by oxygen insertion. The plot of the logarithm (conductivity) vs. T⁻¹ gives average activation energy of 0.12 eV. CuFeO₂ is a narrow band gap semiconductor with an optical gap of 1.32 eV. The oxide was characterized photoelectrochemically; its conduction band (−1.09 V_RHE) is located below that of SnO₂ (−0.86 V_RHE) at pH ∼13.5 itself more negative than the H₂O/H₂ level leading to a thermodynamically favorable H₂ evolution under visible irradiation. The sensitizer CuFeO₂, working as an electron pump, is stable towards photocorrosion by hole consumption reactions involving the reducing agents X²⁻ (=S₂O₃²⁻ and SO₃²⁻). The photoactivity was dependent on the precursor and the best performance (0.026 ml h⁻¹ mg⁻¹) was obtained in S₂O₃²⁻ (pH ∼13.5) over CuFeO₂ synthesized from nitrate with a mass ratio (CuFeO₂/SnO₂) equal to unity. A quantum yield of 0.5% was obtained under polychromatic light. H₂ liberation occurs concomitantly with the oxidation of S₂O₃²⁻ to dithionate and sulfate. The tendency towards saturation, in a closed system, is mainly ascribed to the competitive reduction of the end product S₂O₆²⁻.     

Electrospun Pt/TiO2 hybrid nanofibers for visible-light-driven H2 evolution

One-dimensional (1D) Pt/TiO₂ hybrid nanofibers (HNFs) with different concentrations of Pt were fabricated by a facile two-step synthesis route combining an electrospinning technique and calcination process. X-ray diffraction (XRD), scanning electron microscopy (SEM), and high-resolution transmission electron microscopy (HRTEM) results showed that the Pt nanoparticles (NPs) with the size of 5–10 nm were well dispersed in the TiO₂ nanofibers (NFs). Further investigations from the UV–Vis diffuse reflectance (DR) and X-ray photoelectron spectroscopy (XPS) analysis revealed that some Pt ions were incorporated into the TiO₂ lattice as Pt⁴⁺ state, which contributed to the visible light absorption of TiO₂ NFs. Meanwhile, the Pt²⁺ ions existing on the surface of Pt NPs resulted in the formation of Pt–O–Ti bond at Pt NPs/TiO₂ NFs interfaces that might serve as an effective channel for improving the charge transfer. The as-electrospun Pt/TiO₂ HNFs exhibited remarkable activities for photocatalytic H₂ evolution under visible light irradiation in the presence of l-ascorbic acid as the sacrificial agent. In particular, the optimal HNFs containing 1.0 at% Pt showed the H₂ evolution rate of 2.91 μmol h⁻¹ and apparent quantum efficiency of 0.04% at 420 nm by using only 5 mg of photocatalysts. The higher photocatalytic activity could be ascribed to the appropriate amount of Pt ions doping and excellent electron-sink effect of Pt NPs co-catalysts.     

A comparative study of Pt/C cathodes in Sn0.9In0.1P2O7 and H3PO4 ionomers for high-temperature proton exchange membrane fuel cells

New Pt/C cathodes with many reaction sites for the oxygen reduction reaction as well as high tolerance to Pt corrosion have been designed for high-temperature proton exchange membrane fuel cells (PEMFCs), wherein a composite mixture of Sn_0.9In_0.1P₂O₇ (SIPO) and sulfonated polystyrene-b-poly(ethylene/butylene)-b-polystyrene (sSEBS) functioned as an ionomer. The microstructure of the Pt-SIPO-sSEBS/C cathode was characterized by homogeneous distribution of the ionomer over the catalyst layer and close contact between the ionomer and the Pt/C powder. As a result, the activation and concentration overpotentials of the Pt-SIPO-sSEBS/C cathode between 100 and 200 °C were lower than those of an H₃PO₄-impregnated Pt/C cathode, which suggests that the present ionomer can avoid poisoning of Pt by phosphate anions and the limitation of gas diffusion through the catalyst layer. Moreover, agglomeration of Pt in the Pt-SIPO-sSEBS/C cathode was not observed during a durability test at 150 °C for 6 days, although it was significant in the Pt-H₃PO₄/C cathode. Therefore, it is concluded that the Pt-SIPO-sSEBS/C electrode is a very promising cathode candidate for high-temperature PEMFCs.     

Catalytic behavior of Ni/ZrxTi1−xO2 and the effect of SiO2 doping in oxidative steam reforming of n-butane

Catalytic behaviors of TiO₂-, Zr_0.5Ti_0.5O₂-, and ZrO₂-supported Ni catalysts were investigated for oxidative steam reforming of n-C₄H₁₀ at 723 K. The composite oxide support, Zr_0.5Ti_0.5O₂, shows high specific surface area (136 m²/g), leading to fine Ni particles. Thus, the Ni/Zr_0.5Ti_0.5O₂ catalyst exhibits higher and more stable activity than that exhibited by other catalysts. However, relatively large amounts of coke are deposited on the catalyst during reaction. Thus, to retard carbon deposition, the influence of SiO₂ additive was studied. Large amounts of SiO₂ additive (5 or 10 mol%) decrease initial activity; at 10 mol%, degradation is also induced by oxidation of Ni⁰. However, small amounts of SiO₂ additive (1.5 mol%) effectively retard coking without lowering initial activity. The resultant Ni/Zr_0.5Ti_0.5O₂–SiO₂ (1.5 mol%) catalyst exhibits high and stable activity without coking.