红外高光谱大气探测仪星载固定点黑体辐射源的研制

介绍了中国计量科学研究院为风云三号05星红外高光谱大气探测仪研制的微型镓固定点星载黑体辐射源。设计了黑体辐射源空腔,其有效发射率优于0.997。针对星载固定点黑体辐射源的结构设计和性能测试展开了研究:星载固定点黑体辐射源17 ℃的温度均匀性仿真结果优于0.01℃;黑体辐射源在真空下均匀性优于0.02 ℃,稳定性优于0.002 ℃(90 min内);在通过满足航天应用的力学冲击等实验后,镓固定点的复现性优于0.03 ℃;微型固定点相变温坪复现实验加热功率与拐点值之间存在较好的线性关系。     

英国国家物理实验室（NPL）标准黑体辐射源

英国国家物理实验室（ＮＰＬ）标准黑体辐射源Ｂ．Ｃｈｕ等ＮＰＬ设计的系列标准黑体可以给实际空腔提供适当的靶面尺寸和方便的校准，同时保持高的发射率。现将ＮＰＬ固定点黑体和可变温黑体的设计和构造介绍如下。１．固定点黑体ＮＰＬ已构造出实现银（９６１．７８℃）...     

关于换热器的低温黑体辐射源

介绍一种工作在-80℃～+100℃的基于换热器的新型低温标准黑体辐射源的设计和其发射率的计算.这种黑体辐射源采用液体恒温槽均温致冷和采用气帘隔离法消除低温凝露和结霜,黑体空腔形状为圆锥圆柱型,锥角为120°,空腔内径50mm,腔长为300mm,控温稳定性优于±0.05℃/30min.理论计算的黑体空腔有效发射率为0.998(保留小数点后三位),比对实验测量得到的有效发射率为0.997(保留小数点后三位),二者接近一致.     

氟利昂热管黑体辐射源性能实验研究

为了满足机场、车站等红外筛检仪器辐射温度现场校准的要求,文章介绍了一种氟利昂热管黑体辐射源。黑体辐射源空腔形状为圆柱-圆锥形,空腔长100 mm,锥角为120腔,法向平均有效发射率计算值为0.995。利用TRT2辐射温度计对黑体辐射源腔底进行辐射温度测量,对热管进行不同角度的倾斜,测得的黑体辐射源温度稳定性优于0.2℃,氟利昂热管空腔内均匀性优于0.2℃,可以满足现场校准需求。     

H500型红外遥感定标高精度真空黑体辐射源的研制

对中国计量科学研究院研制的温度范围覆盖-93~220℃的H500型红外遥感定标高精度真空黑体辐射源进行了介绍。采用圆柱圆锥黑体腔和双层4段PID控温,在真空低背景(液氮冷却)环境下对该黑体进行了性能测试,在大气室温环境下,利用控制环境辐射反射比发射率测量方法测量了黑体空腔发射率和利用红外标准辐射温度计测量空腔底部温度均匀性等指标。实验结果表明,该黑体辐射源升温速率为1℃/min下,控制到温度点的稳定时间优于50 min,并且10 min内的温度稳定性在0.01℃以内;黑体温度设置在20℃、30℃和50℃下空腔发射率的测量结果分别为0.9965、0.9966和0.9963;其黑体底部温度均匀性优于0.03℃;在整个温度区域内扩展不确定度优于0.1℃(k=2)。     

中温区真空标准黑体辐射源研制

介绍了中国计量科学研究院研制的中温区真空标准黑体辐射源的结构设计,工作原理,测试结果和不确定度评定.黑体辐射源工作温度范围为320～500 K,黑体空腔开口直径为50 mm,空腔深度为260 mm,表面喷涂了耐高温漆,空腔发射率优于0.999.真空环境下测试了黑体在335～500K温度范围内的轴向温度均匀性,温度稳定性...     

真空汞固定点黑体辐射源的设计与研制

介绍了中国计量科学研究院研制的真空汞固定点黑体辐射源的结构、工作原理、性能测试结果和不确定度分析。真空汞固定点黑体辐射源灌注的是纯度为99.9999%的高纯汞,黑体空腔开口直径为25 mm,空腔内径为28 mm,深度为260 mm,表面喷涂了NEXTEL 811-21高发射率涂层,采用基于蒙特卡罗黑体发射率仿真计算的方法,计算了黑体空腔在波长为8~14μm的发射率,结果优于0.9999;在真空环境下,测试了真空汞固定点黑体辐射源的温坪曲线和重复性等主要技术指标,结果表明真空汞固定点黑体辐射源温坪稳定性优于2 mK,多次重复性优于1 mK;分析了真空汞固定点黑体辐射源的不确定度来源,其合成标准不确定度为16 mK。     

100～400K真空红外亮温标准黑体辐射源研制

介绍了中国计量科学研究院研制的100~400K真空红外亮温标准黑体辐射源的工作原理、结构、性能测试方法及测试结果。黑体辐射源通过液氮制冷与3温区控制实现了100~400K范围内的温度控制。在真空环境下,测试了其在温度范围100~400K轴向温度均匀性、底部温度稳定性等技术指标,结果表明均匀性优于0.120K,控温稳定性优于0.020K/20min;在室温大气环境下,利用基于控制环境辐射的发射率测量方法测量了黑体空腔发射率,空腔法向发射率为0.9998。采用基于蒙特卡罗黑体发射率仿真计算方法分析轴向温度均匀性对空腔发射率的影响,分析了标准黑体辐射源的不确定度来源,在8~16 μm波长亮度温度的合成标准不确定度优于0.030K。     

铯、钠热管标准黑体辐射源研制及性能评价

介绍了中国计量科学研究院研制的270～1 000 ℃标准黑体辐射源,其中包括270～600 ℃铯热管黑体源和500～1 000 ℃钠热管黑体源、温度标准器和数据采集系统。对铯、钠热管标准黑体辐射源进行性能测试,包括三段控温管式炉温场均匀性,黑体辐射源控温稳定性,黑体空腔轴向温度均匀性,黑体空腔口部辐射温度均匀性和热管测温孔内温度均匀性等。铯、钠热管标准黑体辐射源在整个温度区域内合成标准不确定度为0.09～0.13 ℃（k=2）。     

采用统计方法减小黑体辐射源比较分度噪声等效温差

分析了黑体辐射源比较测量过程的特点,采用消除辐射温度计线性漂移的比较测量方法,抑制辐射温度计输出非线性漂移和随机噪声影响统计平均处理方法,减小辐射温度计的噪声等效温差.使用不同的统计平均数量,得到相应测量条件下黑体辐射源比较分度的测量水平.测量结果中噪声等效温差可以优于0.01℃.统计处理方法不仅可以应用在黑体辐射源比较分度中,而且可以扩展应用在与黑体辐射源比较分度类似比较测量过程.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...