Sintering Behavior and Surface Microstructure of PbO-Rich PbNi1/3Nb2/3O3–PbTiO3–PbZrO3 Ceramics

The sintering behavior and surface microstructure of PbNi_1/3Nb_2/3O₃–PbTiO₃–PbZrO₃ (PNiNb-PT-PZ) ceramics were investigated. The PNiNb-PT-PZ ceramics with the stoichiometric composition and the addition of excess lead oxide (PbO-rich ceramics) were sintered by liquid-phase sintering in accordance with the solution-reprecipitation mechanism at temperatures below the melting point of PbO. The temperature at which the liquid phase forms fell to near the eutectic point of the PbO–Nb₂O₅ and the PbO–TiO₂ system (868°C) with the addition of 5 mol% PbO. As the calcination temperature influenced the sinterability of the stoichiometric PNiNb-PT-PZ ceramic, unreacted PbO was considered to be the source of the liquid phase in the sintering of the stoichiometric powder. The secondary phase was observed at the surface of PbO-rich ceramics and was suggested to be a liquid phase expelled from inside the ceramic. A sintering scheme of PNiNb-PT-PZ ceramics was proposed, and the high sinterability of PNiNb-PT-PZ ceramics was attributed to the low formation temperature of the liquid phase.     

Synthesis of Pb(Mg1/3Nb2/3)O3 in Excess Lead Oxide by Mechanical Activation

Twenty hours of mechanical activation of mixed oxides at room temperature led to the formation of Pb(Mg_1/3Nb_2/3)O₃ (PMN) in excess PbO. The crystallinity of the activation-derived perovskite PMN phase was further established when the activated PMN–PbO phase mixture was subjected to calcination at 800°C. Pyrochlores, such as Pb₃Nb₄O₁₃ and Pb₂Nb₂O₇, were not observed as transitional phases on mechanical activation and subsequent calcination, although 50% excess PbO was deliberately added. The perovskite PMN phase was recovered by washing off excess PbO using acetic acid solution at room temperature. It was sintered to a relative density of 98.9% of theoretical at 1200°C for 1 h and the sintered PMN exhibited a dielectric constant of ∼14 000 at 100 Hz and a Curie temperature of −11°C.     

Annealing of Sintered Pb0.9175La0.055Zr0.975Ti0.025O3 in Air

Annealing of a sintered pellet of Pb_0.9175La_0.055Zr_0.975Ti_0.025O₃ in air without any precautions against PbO evaporation results in a core–shell microstructure with a solid PLZT core and a porous ZrO₂-rich shell.     

New Preparation Method of Low-Temperature-Sinterable Perovskite 0.9Pb(Mg1/3Nb2/3)O3-0.1PbTiO3 Powder and Its Dielectric Properties

A relaxor ferroelectric material, 0.9Pb(Mg_1/3Nb_2/3)O₃-0.1PbTiO₃ (0.9PMN-0.1PT) with a pyrochlore-free phase, was prepared by using one-step calcination in the present study. The 0.9PMN-0.1PT powder with the pure perovskite phase was prepared successfully from a mixture of the PMN precursor and the crystalline PT by heating for 2 h at temperatures greaterthan equal to750°C. The PMN precursor was synthesized by adding an aqueous Mg(NO₃)₂ solution, rather than MgO, to the alcoholic slurry of PbO and Nb₂O₅. The 0.9PMN-0.1PT powder sintered to >96% relative density via heat treatment for 2 h at temperatures of 900°-1200°C. The highest room-temperature dielectric constant (epsilon_rt) was 24700 at 1 kHz for the samples that were sintered at 1100°C; however, the samples that were sintered at 900°C still had epsilon_rt values of 22600 at 1 kHz.     

Perovskite Phase Formation in the Relaxor System [Pb(Fe1/2Nb1/2)O3]1-x–[Pb(Zn1/3Nb2/3)O3]x

Phase formation and dielectric properties of the compositions in the system [Pb(Fe_1/2Nb_1/2)O₃]₁_ _x –[Pb(Zn_1/3Nb_2/3)O₃] _x were investigated as possible materials for multilayer ceramic capacitors. The formation of the phase with perovskite structure and dielectric properties of ceramics at room temperature in the entire composition range are presented. The undesirable pyrochlore phase can be suppressed up to x = 0.6 by adopting calcination of B-site oxides, followed by reaction with PbO. Compositions in the single-phase range can be sintered at less than 1000°C.     

Sintering of Si3N4-Y2O3 Under Nitrogen Pressure

This study shows that the amount ofAl₂O₃ needed to form high density Si₃N₄-15Y₂-O₃ samples can be reduced by using high surface area Si₃N₄ powder and high N₂ overpressure (high sintering temperatures) during the sintering process. The reduction in AI₂O₃ content results in improved oxidation resistance of the sintered samples.     

Double Precursor Solution Coating Approach for Low-Temperature Sintering of [Pb(Mg1/3Nb2/3)O3]0.63[PbTiO3]0.37 Solids

Lead-based piezoelectric ceramics typically require sintering temperatures higher than 1000°C at which significant lead loss can occur. Here, we report a double precursor solution coating (PSC) method for fabricating low-temperature sinterable polycrystalline [Pb(Mg_1/3Nb_2/3)O₃]_0.63-[PbTiO₃]_0.37 (PMN–PT) ceramics. In this method, submicrometer crystalline PMN powder was first obtained by dispersing Mg(OH)₂-coated Nb₂O₅ particles in a lead acetate/ethylene glycol solution (first PSC), followed by calcination at 800°C. The crystalline PMN powder was subsequently suspended in a PT precursor solution containing lead acetate and titanium isopropoxide in ethylene glycol to form the PMN–PT precursor powder (second PSC) that could be sintered at a temperature as low as 900°C. The resultant d ₃₃ for samples sintered at 900°, 1000°, and 1100°C for 2 h were 600, 620, and 700 pm/V, respectively, comparable with the known value. We attributed the low sintering temperature to the reactive sintering nature of the present PMN–PT precursor powder. The reaction between the nanosize PT and the submicrometer-size PMN occurred roughly in the same temperature range as the densification, 850°–900°C, thereby significantly accelerating the sintering process. The present PSC technique is very general and should be readily applicable to other multicomponent systems.     

PbTiO3-PbO-B2O3 Glass-Ceramics by a Sol-Gel Process

PbTiO₃ (PT)-PbO-B₂O₃ glass-ceramics were produced by a sol-gel process. Achievement of high PT content at levels unattainable by conventional glass-ceramics preparation methods was semiquantitatively shown. PT content was similar to the designed PT volume fraction and seemed rather unaffected by the composition of the glassforming component at a calcination temperature of 700°C. A higher ratio of PbO to B₂O₃ in the glassforming component resulted in a low PT crystallization temperature, <500°C. PT crystals 1-2 μm in size were obtained at calcination temperatures >600°C.     

Effect of Bi2O3 Addition on the Sintering Temperature and Microwave Dielectric Properties of Zn2SiO4 Ceramics

Bi₂O₃ was added to a nominal composition of Zn_1.8SiO_3.8 (ZS) ceramics to decrease their sintering temperature. When the Bi₂O₃ content was <8.0 mol%, a porous microstructure with Bi₄(SiO₄)₃ and SiO₂ second phases was developed in the specimen sintered at 885°C. However, when the Bi₂O₃ content exceeded 8.0 mol%, a liquid phase, which formed during sintering at temperatures below 900°C, assisted the densification of the ZS ceramics. Good microwave dielectric properties of Q × f =12,600 GHz, ɛ_r=7.6, and τ_f=−22 ppm/°C were obtained from the specimen with 8.0 mol% Bi₂O₃ sintered at 885°C for 2 h.     

Single-Calcination Synthesis of Pyrochlore-Free 0.9Pb(Mg1/3Nb2/3)O3–0.1PbTiO3 and Pb(Mg1/3Nb2/3)O3 Ceramics Using a Coating Method

A coating approach for synthesizing 0.9Pb(Mg_1/3Nb_2/3)O₃–0.1PbTiO₃ (0.9PMN–0.1PT) and PMN using a single calcination step was demonstrated. The pyrochlore phase was prevented by coating Mg(OH)₂ on Nb₂O₅ particles. Coating of Mg(OH)₂ on Nb₂O₅ was done by precipitating Mg(OH)₂ in an aqueous Nb₂O₅ suspension at pH 10. The coating was confirmed using optical micrographs and zeta-potential measurements. A single calcination treatment of the Mg(OH)₂-coated Nb₂O₅ particles mixed with appropriate amounts of PbO and PbTiO₃ powders at 900°C for 2 h produced pyrochlore-free perovskite 0.9PMN–0.1PT and PMN powders. The elimination of the pyrochlore phase was attributed to the separation of PbO and Nb₂O₅ by the Mg(OH)₂ coating. The Mg(OH)₂ coating on the Nb₂O₅ improved the mixing of Mg(OH)₂ and Nb₂O₅ and decreased the temperature for complete columbite conversion to ∼850°C. The pyrochlore-free perovskite 0.9PMN–0.1PT powders were sintered to 97% density at 1150°C. The sintered 0.9PMN–0.1PT ceramics exhibited a dielectric constant maximum of ∼24 660 at 45°C at a frequency of 1 kHz.     

Sintering and Crystallization of CaO–Al2O3–ZrO2–SiO2 Glasses Containing Different Amount of Al2O3

In this work several complementary techniques have been employed to carefully characterize the sintering and crystallization behavior of CaO–Al₂O₃–ZrO₂–SiO₂ glass powder compacts after different heat treatments. The research started from a new base glass 33.69 CaO–1.00 Al₂O₃–7.68 ZrO₂–55.43SiO₂ (mol%) to which 5 and 10 mol% Al₂O₃ were added. The glasses with higher amounts of alumina sintered at higher temperatures (953°C [lower amount] vs. 987°C [higher amount]). A combination of the linear shrinkage and viscosity data allowed to easily find the viscosity values corresponding to the beginning and the end of the sintering process. Anorthite and wollastonite crystals formed in the sintered samples, especially at lower temperatures. At higher temperatures, a new crystalline phase containing ZrO₂ (2CaO·4SiO₂·ZrO₂) appeared in all studied specimens.     

Effect of Li2CO3 Addition on the Sintering Temperature and Microwave Dielectric Properties of Mg2V2O7 Ceramics

Li₂CO₃ was added to Mg₂V₂O₇ ceramics in order to reduce the sintering temperature to below 900°C. At temperatures below 900°C, a liquid phase was formed during sintering, which assisted the densification of the specimens. The addition of Li₂CO₃ changed the crystal structure of Mg₂V₂O₇ ceramics from triclinic to monoclinic. The 6.0 mol% Li₂CO₃-added Mg₂V₂O₇ ceramic was well sintered at 800°C with a high density and good microwave dielectric properties of ɛ _r=8.2, Q × f =70 621 GHz, and τ_f=−35.2 ppm/°C. Silver did not react with the 6.0 mol% Li₂CO₃-added Mg₂V₂O₇ ceramic at 800°C. Therefore, this ceramic is a good candidate material in low-temperature co-fired ceramic multilayer devices.     

Microwave Dielectric Properties of Li2TiO3 Ceramics Doped with ZnO–B2O3 Frit

A type of new low sintering temperature ceramic, Li₂TiO₃ ceramic, has been found. Although it is difficult for the Li₂TiO₃ compound to be sintered compactly at temperatures above 1000°C for the volatilization of Li₂O, dense Li₂TiO₃ ceramics were obtained by conventional solid-state reaction method at the sintering temperature of 900°C with the addition of ZnO–B₂O₃ frit. The sintering behavior and microwave dielectric properties of Li₂TiO₃ ceramics with less ZnO–B₂O₃ frit (≤3.0 wt%) doping were investigated. The addition of ZnO–B₂O₃ frit can lower the sintering temperature of the Li₂TiO₃ ceramics, but it does not apparently degrade the microwave dielectric properties of the Li₂TiO₃ ceramics. Typically, the good microwave dielectric properties of ɛ_r=23.06, Q × f =32 275 GHz, τ_f = 35.79 ppm/°C were obtained for 2.5 wt% ZnO–B₂O₃ frit-doped Li₂TiO₃ ceramics sintered at 900°C for 2 h. The porosity was 0.08%. The Li₂TiO₃ ceramic system may be a promising candidate for low-temperature cofired ceramics applications.     

Sintering of UN as a Function of Temperature and N2 Pressure

The sintering of uranium mononitride (UN) depends on temperature and the N₂ pressure maintained over the nitride during heat treatment. At a given temperature, an N₂ pressure that maintained the UN in the single-phase region slightly above the phase boundary where the reaction UN→U+½N₂(g) occurred was most effective in accelerating the sintering of single-phase UN. For example, specimens sintered at 1600°C under N₂ pressures of either 1140 or 1.7XlO⁻⁴ torr had essentially identical compositions, but the density of the former was 10.78 g/cm³ (75% of theoretical), whereas that of the latter was 12.20 g/cm³ (85% of theoretical). Results were similar at temperatures up to 2100°C. The X-ray lattice constant of UN sintered at reduced N₂ pressures was slightly larger than that of UN sintered in 1140 torr of N₂. The observed constants ranged from 4.88904 to 4.88991 Å; the combined O+C content varied from 400 to 900 ppm.     

Microstructure and Nonlinear Properties of Microwave-Sintered ZnO-V2O5 Varistors: I, Effect of V2O5 Doping

The modification of the densification behavior and the grain-growth characteristics of the microwave-sintered ZnO materials, caused by the incorporation of V₂O₅ additives, have been systematically studied. Generally, the addition of V₂O₅ markedly enhances the densification rate, such that a density as high as 97.9% of the theoretical density and a grain size as large as 10 µm can be attained for a sintering temperature as low as 800°C and a soaking time as short as 10 min. Increasing the sintering temperature or soaking time does not significantly change the sintered density of the ZnO-V₂O₅ materials but it does monotonously increase their grain size. Varying the proportion of V₂O₅ in the range of 0.2-1.0 mol% does not pronouncedly modify such behavior. The leakage current density ( J _L) of these high-density and uniform-granular-structure samples is still large, which is amended by the incorporation of 0.3 mol% of Mn₃O₄ in the ZnO materials, in addition to 0.5 mol% of the V₂O₅ additives. Samples that are obtained using such a method possess good nonohmic characteristics (α= 23.5) and a low leakage current density ( J _L= 2.4 10^-6 A/cm²).     

Effect of Excess PbO on the Sintering Characteristics and Dielectric Properties of Pb(Mg1/3Nb2/3)O3–PbTiO3-Based Ceramics

Additions of excess PbO to the perovskite Pb[(Mg_1/3Nb_2/3)_0.92Ti_0.08]O₃ solid solution enhanced the formation of a liquid phase at 840°C, which served as a densification aid for the ceramics. The liquid phase allowed elimination of pores and promoted grain growth during sintering. With additions of 1 to 2 wt% excess PbO, densities in excess of 97% of theoretical were obtained at a sintering temperature of 950°C. The peak dielectric constants of the resulting ceramics were over 18 000 at 30°C and dissipation factors less than 1%. Additions of PbO in excess of 2 wt% resulted in inferior dielectric properties due mainly to the dilution of the ferroelectric phase.     

Effects of B2O3 on the Phase Stability of Ba2Ti9O20 Microwave Ceramic

Preparation of dense and phase-pure Ba₂Ti₉O₂₀ is generally difficult using solid-state reaction, since there are several thermodynamically stable compounds in the vicinity of the desired composition and a curvature of Ba₂Ti₉O₂₀ equilibrium phase boundary in the BaO–TiO₂ system at high temperatures. In this study, the effects of B₂O₃ on the densification, microstructural evolution, and phase stability of Ba₂Ti₉O₂₀ were investigated. It was found that the densification of Ba₂Ti₉O₂₀ sintered with B₂O₃ was promoted by the transient liquid phase formed at 840°C. At sintering temperatures higher than 1100°C, the solid-state sintering became dominant because of the evaporation of B₂O₃. With the addition of 5 wt% B₂O₃, the ceramic yielded a pure Ba₂Ti₉O₂₀ phase at sintering temperatures as low as 900°C, without any solid solution additive such as SnO₂ or ZrO₂. The facilities of B₂O₃ addition to the stability of Ba₂Ti₉O₂₀ are apparently due to the eutectic liquid phase which accelerates the migration of reactant species.     

Reaction Sequence and Effects of Calcination and Sintering on Microwave Properties of (Ba,Sr)O-Sm2O3-TiO2 Ceramics

The reaction sequence of 0.15(Ba_0.95Sr_0.05)O· 0.15Sm₂O₃· 0.7TiO₂ ceramics during heating as well as the effects of calcination and sintering on microwave properties were investigated. Quantitative microscopic analysis was performed to obtain the volume fraction of the phases. It was found that the amount of second phase, especially TiO₂ (rutile), greatly affected the temperature coefficient of resonant frequency of the ceramics. The higher the amount of TiO₂ phase, the more positive or the less negative the temperature coefficient of resonant frequency. The temperature coefficient of BaO · Sm₂O₃· 5TiO₂ was calculated using the logarithmic mixing rule to be −30 ppm/°C. The volume fractions of the phases varied with conditions of calcination and sintering. Therefore, by varying calcination and/or sintering temperature, the temperature coefficient of resonant frequency could be adjusted to nearly zero.     

Compositional Change and Compositional Fluctuation in Pb(Zr,Ti)O3 Containing Excess PbO

Compositional changes which take place during sintering of Pb(Zr,Ti)O₃ (PZT) containing excess PbO were studied. The excess PbO forms a liquid phase during the sintering process. The solubility of the TiO₂ component of PZT in liquid PbO is higher than that of ZrO₂ component. Thus, if an excess PbO exists, the composition of PZT phase shifts towards the Ti-lean side. A change in the lattice constants due to this compositional change was actually observed. Coexistence of tetragonal and rhombohedral phases, due to a compositional fluctuation caused by excess PbO, was observed near the morphotropic phase boundary. When PZT containing excess PbO was sintered at 1100°C, a compositional fluctuation occurred early in the process and then decreased with sintering time. These phenomena have agreed with a result of computer simulation of dissolution of TiO₂ component in PZT phase into liquid PbO phase.     

Low-Temperature Sintering and Microwave Dielectric Properties of Li2MgSiO4 Ceramics

Development of a low-temperature sintered dielectric material derived from Li₂MgSiO₄ (LMS) for low-temperature cofired ceramic (LTCC) application is discussed in this paper. The LMS ceramics were prepared by the solid-state ceramic route. The calcination and sintering temperatures of LMS were optimized at 850°C/4 h and 1250°C/2 h, respectively, for the best density and dielectric properties. The crystal structure and microstructure of the ceramic were studied by the X-ray diffraction and scanning electron microscopic methods. The microwave dielectric properties of the ceramic were measured by the cavity perturbation method. The LMS sintered at 1250°C/2 h had ɛ_r=5.1 and tan δ=5.2 × 10⁻⁴ at 8 GHz. The sintering temperature of LMS is lowered from 1250°C/2 h to 850°C/2 h by the addition of both lithium borosilicate (LBS) and lithium magnesium zinc borosilicate (LMZBS) glasses. LMS mixed with 1 wt% LBS sintered at 925°C/2 h had ɛ_r=5.5 and tan δ=7 × 10⁻⁵ at 8 GHz. Two weight percent LMZBS mixed with LMS sintered at 875°C/2 h had ɛ_r=5.9 and tan δ=6.7 × 10⁻⁵ at 8 GHz.