Low temperature production of glass ceramics in the anorthite–diopside system via sintering and crystallization of glass powder compacts

The production of glass ceramics (GCs) with theoretical anorthite–diopside (An–Di) weight ratios of 60/40, 50/50 and 45/55 via sintering and crystallization of glass powder compacts was investigated at different temperatures between 800 and 950 °C. The investigated compositions are located in the cross-section of the ternary fluorapatite–An–Di system close to An–Di binary joint, with constant fluorapatite content of 4.8 wt.%. Two different groups of glass powders, with mean particle size of 2 and 10 μm, were used. The experimental results showed that sintering is almost complete at 800 °C, preceding crystallization, which takes place via surface crystallization mechanism. The properties values of the produced GCs, which are the best for the composition close to An–Di eutectic line, are discussed with respect to the evolution of crystalline phases and the microstructure over increasing firing temperature. Under the technology perspective, the investigated processing route is significantly superior in comparison to the attempts reported in earlier studies.     

Characterization and sintering of gels in the system MgO–Al2O3–SiO2

Cordierite aerogels, made by supercritical drying, and xerogels, formed by ambient pressure drying, have been prepared by combining two different recipes. The chemical composition of the gels varied from stoichiometric cordierite 2MgO·Al₂O₃·5SiO₂ to 0·5MgO·1·4Al₂O₃·5SiO₂ due to different procedures for washing of the gels. The crystallization of nearly stoichiometric cordierite gels was shown to be relatively complex involving the formation of several metastable phases such as μ-cordierite (Mg₂Al₄Si₅O₁₈), spinel (Al₆Si₂O₁₃) and sapphirine (Mg₄Al₈Si₂O₂₀) before the equilibrium phase composition was obtained at around 1350°C. On the other hand, during crystallization of gels with stoichiometry close to 0·5MgO·1·4Al₂O₃·5SiO₂ the equilibrium phases mullite, cristobalite and α-cordierite were the major phases formed during heat treatment. A lower densification rate was observed for aerogels compared to xerogels due to a larger pore size. A lower crystallization temperature in aerogels probably due to heterogeneous nucleation reduced the densification. For gels with a composition near 0·5MgO·1·4Al₂O₃·5SiO₂ nucleation and densification occur simultaneously and large differences in the densification behavior was observed. ©     

Crystallisation and characterisation of dielectric glass ceramics in Li2O–Al2O3–SiO2 system

Abstract

Glass ceramics in the Li₂O–Al₂O₃–SiO₂ system have been synthesised to produce bulk materials grown in a glass phase via quenching followed by controlled crystallisation. The crystallisation and microstructure of Li₂O–Al₂O₃–SiO₂ (LAS) glass–ceramic with nucleating agents (B₂O₃ and/or P₂O₅) are investigated by differential thermal analysis, X-ray diffraction and scanning electron microscopy and the effects of B₂O₃ and P₂O₅ on the crystallisation of LAS glass are also analysed. The introduction of both B₂O₃ and P₂O₅ promotes the crystallisation of LAS glass by decreasing the crystallisation temperature and adjusting the crystallisation kinetic parameters, allows a direct formation of β spodumene phase and as a result, increases the crystallinity of the LAS glass ceramic. Microstructural observations show that the randomly oriented, nanometre sized crystalline is found with residual glass concentrated at crystallite boundaries. Furthermore, it is interesting that codoping of B₂O₃ and P₂O₅ creates not much effect on the crystallisation temperature. The dielectric properties of the glass–ceramics formed through controlled crystallisation have a strong dependence on the phases that are developed during heat treatment. The dielectric constant is continuously increased and the dielectric loss is decreased with addition of additives where mobile alkali metal ions (e.g. Li⁺) are incorporated in a crystal phase and minimise the residual glass phase.     

Effect of CaO doping on the properties and crystallization behavior of Y2O3–Al2O3–SiO2 glass

Nowadays, Y₂O₃–Al₂O₃–SiO₂ (YAS) glass joining is considered to be a promising scheme for nuclear-grade continuous silicon carbide (SiC) fiber reinforced SiC matrix composites (SiC/SiC). CaO has great potential for nuclear applications since it has low reactivity and low decay rate under nuclear irradiation. In this paper, the effect of CaO doping on the structure, thermophysical properties, and crystallization behavior of YAS glass was systematically studied. As the CaO doping content increased, the number of bridge oxygens and the viscosity at high temperatures reduced gradually. After heat treatment at 1400 °C, the main phases in YAS glass were β-Y₂Si₂O₇, mullite, and SiO₂ (coexistence of crystalline and glass phases), while that with 3.0% CaO doping turned into a single glassy phase under the same treatment conditions. Moreover, a structural model and the modification mechanism were proposed, which provided a theoretical basis for the subsequent component design and optimization.     

Effect of Al2O3 and K2O content on structure,properties and devitrification of glasses in the Li2O–SiO2 system

The effect of Al₂O₃ and K₂O content on structure, sintering and devitrification behaviour of glasses in the Li₂O–SiO₂ system along with the properties of the resultant glass–ceramics (GCs) was investigated. Glasses containing Al₂O₃ and K₂O and featuring SiO₂/Li₂O molar ratios (3.13–4.88) far beyond that of lithium disilicate (Li₂Si₂O₅) stoichiometry were produced by conventional melt-quenching technique along with a bicomponent glass with a composition 23Li₂O–77SiO₂ (mol.%) (L₂₃S₇₇). The GCs were produced through two different methods: (a) nucleation and crystallization of monolithic bulk glass, (b) sintering and crystallization of glass powder compacts.Scanning electron microscopy (SEM) examination of as cast non-annealed monolithic glasses revealed precipitation of nanosize droplet phase in glassy matrices suggesting the occurrence of phase separation in all investigated compositions. The extent of segregation, as judged from the mean droplet diameter and the packing density of droplet phase, decreased with increasing Al₂O₃ and K₂O content in the glasses. The crystallization of glasses richer in Al₂O₃ and K₂O was dominated by surface nucleation leading to crystallization of lithium metasilicate (Li₂SiO₃) within the temperature range of 550–900 °C. On the other hand, the glass with lowest amount of Al₂O₃ and K₂O and glass L₂₃S₇₇ were prone to volume nucleation and crystallization, resulting in formation of Li₂Si₂O₅ within the temperature interval of 650–800 °C.Sintering and crystallization behaviour of glass powders was followed by hot stage microscopy (HSM) and differential thermal analysis (DTA), respectively. GCs from composition L₂₃S₇₇ demonstrated high fragility along with low flexural strength and density. The addition of Al₂O₃ and K₂O to Li₂O–SiO₂ system resulted in improved densification and mechanical strength.     

Effect of TiO2 on microphase development during phase separation and crystallization in Na2O–B2O3–SiO2 glass system

This study examines the incorporation of TiO₂ into sodium borosilicate glasses and its effect on the formation of glassy and crystalline microphases. Glasses in the composition range: 7Na₂O–23B₂O₃–(70 - X)SiO₂–XTiO₂ (where X = 0–14.6 mol.% TiO₂) which exhibit phase separation were investigated. Raman studies confirm the formation of two different TiO₂ coordinations depending on the molar content of TiO₂. Thermal properties of glasses are unaffected by TiO₂ addition. The domain size of microphase development in TiO₂-containing glass indicates competition between phase separation and crystallization. Enrichment of titanium on the interphase between glassy microphases reduces the mass transfer and consequently limits the growth rate of glassy phases. This competes with the formation of anatase for which a nucleation-controlled mechanism is proposed.     

Dual effect of ZrO2 on phase separation and crystallization in Li2O–Al2O3–SiO2–P2O5 glasses

ZrO₂ is an effective nucleation agent for low-expansion lithium–aluminum silicate (LAS) glass–ceramic (GC) with high Al₂O₃ content. However, the effect of ZrO₂ is still not fully understood in LAS glasses with low contents of Al₂O₃ and P₂O₅. In this work, the effect of ZrO₂ on the phase separation and crystallization of Li₂O–Al₂O₃–SiO₂–P₂O₅ glasses were investigated. The results revealed that ZrO₂ significantly increased T_g and the crystallization temperature of Li₂SiO₃ and Li₂Si₂O₅ crystals. Li₃PO₄ crystals precipitated preferentially in the glass containing 3.6-mol% ZrO₂, wherein Zr was stable in the network and no precipitation of ZrO₂ nanocrystals was observed. Moreover, the separation of phosphate-rich phases in the as-quenched glasses increased with the addition of ZrO₂. The findings of the study revealed a dual role of ZrO₂. First, ZrO₂ acted as a glass network former rather than a nucleation agent, increasing glass viscosity and the nucleation barrier of Li₂SiO₃ through its strong network connectivity. Second, as Zr preferentially combined with non-bridging oxygen to form Si–O–Zr linkages, a sufficient amount of charge-balancing Li⁺ ions existed in the network, which promoted the separation of phosphate-rich phases. It indicated that the incorporation of ZrO₂ contributes to the activation of the nucleation role of P₂O₅, thus contributing to the formation of nanocrystals and fine microstructure of GCs.     

Effect of BaO ratio on the structure of glass–ceramic composite materials from the SiO2–Al2O3–Na2O–K2O–CaO system

This article focused on effect of the content of barium oxide on microstructure of the glass–ceramic materials based on the system SiO₂–Al₂O₃–Na₂O–K₂O–CaO. The following characterisation techniques have been used: X-ray diffraction (XRD), scanning electron microscopy with micro-analyser (SEM–EDS), mid-infrared analysis (MIR), far-infrared analysis (FIR) and Raman Spectroscopy. Significant differences were observed in microstructure of silica–alumina network of glassy phase and phase composition related to changes in the amount of the barium oxide additive. Discussed results are part of a larger project implemented under the PBS Applied Research Programme, in order to determine the compositions of glass–ceramic materials with potential application as a chemically resistant hard coatings or/and resistant to thermal shock or as construction materials.     

Bioactivity investigation of glass and glass ceramics in Li2O–SiO2–CaO–P2O5–CaF2 system

Abstract

Glass samples in Li₂O–SiO₂–CaO–P₂O₅–CaF₂ system with different contents of P₂O₅, CaO and CaF₂ in relative ratios responded to fluoroapatite (FA) composition (referred to P₂O₅ addition) have been prepared and heat treated at 550 and 750°C to obtain glass ceramics. Bioactivity of all samples has been proved in vitro by the presence of new layer of apatite-like phases formed after soaking in simulated body fluid (SBF). The development and the apatitic character of created layers have been demonstrated by Fourier transform infrared analysis. Scanning electron microscopy and electron probe microanalysis have demonstrated that the density and the thickness of new layer depend on P₂O₅ content, crystallisation temperature and immersion time. The bioactivity has been enhanced by P₂O₅ addition as well in the case of the base glasses as in the case of glass ceramics. The additional heat treatment appeared to inhibit the bioactive behaviour, though the longer SBF acting leads to the additional formation of apatite-like layer. The mechanical properties, expressed as Vicker hardness, have been found higher and increasing with P₂O₅ in glass ceramics treated at 750°C comparatively with base glass samples and the highest value of 7˙37 GPa has been achieved by 14 wt-%P₂O₅ addition. The same content of P₂O₅ in glass ceramics heat treated at 550°C resulted in a decrease in hardness to a minimum value from all samples. The increase and decrease in hardness responded to development and suppression of crystallisation respectively. The inhibition of crystallisation has been affected by the presence of 'amorphous' FA according to X-ray diffraction and differential thermal analysis results.     

Effect of MgO/Al2O3 ratio on the crystallization behaviour of Li2O–MgO–Al2O3–SiO2 glass-ceramic and its wettability on Si3N4 ceramic

The composition governs the crystallization ability, the type and content of crystal phases of glass-ceramics. Glass-ceramic joining materials have generated more research interest in recent years. Here, we prepared a novel Li₂O–MgO–Al₂O₃–SiO₂ glass-ceramic for the application of joining Si₃N₄ ceramics. We investigated the influence of the MgO/Al₂O₃ composition ratio on microstructure and crystallization behaviour. The crystallization kinetics demonstrated that the glasses had excellent crystallization ability and high crystallinity. β-LiAlSi₂O₆ and Mg₂SiO₄ were precipitated from the glass-ceramics, and the increase of MgO concentration was conducive to the precipitation of Mg₂SiO₄. Among the glass-ceramic samples, the thermal expansion coefficient of LMAS2 glass-ceramic was 3.1 × 10^?6/°C, which was very close to that of Si₃N₄ ceramics. The wetting test showed that the final contact angle of the glass droplet on the Si₃N₄ ceramic surface was 32° and the interface was well bonded.     

Effect of substitution of ZrO2 by SnO2 on crystallization and properties of environment-friendly Li2O–Al2O3–SiO2 system (LAS) glass-ceramics

In this study, a transparent and environmentally friendly Li₂O–Al₂O₃–SiO₂ (LAS) glass-ceramic was prepared by melt-quenching and two-step heat treatment. The influence of the substitution amount of ZrO₂ by SnO₂ on the crystallization, microstructure, transparency, and mechanical properties of LAS glass and glass-ceramics was investigated by means of differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Ultraviolet–visible Spectrophotometer, three-point bending strength test, and microhardness test. The results indicate that the main crystalline phase of LAS glass ceramics was a β-quartz solid solution when heat treated at 780 °C for 2 h and 870 °C for 1.5 h. When the substitution amount of ZrO₂–SnO₂ increased from 0.4 mol% to 2.5 mol%, the grain size and thermal expansion coefficient of LAS glass-ceramics first decreased and then increased, and the crystallinity first increased and then decreased. When the substitution amount of ZrO₂–SnO₂ was 0.8 mol%, the transparency of the LAS glass-ceramics was maximum, the bending strength was 96 MPa, and the Vickers hardness was 10.9 GPa.     

Thermodynamics and crystallization kinetics of REEs in CaO–SiO2–Ce2O3 system

Rare earth elements (REEs) have become increasingly important as ceramic materials. The RE-bearing slags contain massive REEs resources, whereas the lack of thermodynamic and kinetic data of REEs has brought great difficulties to efficient recovery of REEs from RE-bearing slags and the application in ceramics. According to the compositions of the RE-bearing slags in industrial production, the isothermal phase equilibria of CaO–SiO₂–Ce₂O₃ system at 1500°C and 1300°C were constructed by means of liquid-quenching method combined with a series of analyses, which provides the thermodynamic data for the equilibria of REEs. On this basis, the crystallization behaviors of the RE phase (Ce_9.33−xCa_x(SiO₄)₆O_2−0.5x) was investigated, and the temperature range in which the RE phase crystallized singly in RE-bearing slags with a selected compositions was acquired. CCT and TTT diagrams for CaO–SiO₂–Ce₂O₃ system were established to characterize the crystallization kinetics of the RE phase, and the favorable conditions for its crystallization and growth in RE-bearing slags were determined. In this study, the complete thermodynamic and kinetic basic data of REEs in CaO–SiO₂–Ce₂O₃ system are provided for RE-bearing slags.     

The impact of nano-quartz on the structure of glass-ceramic glazes from the SiO2–Al2O3–CaO–MgO–Na2O–K2O system

The present study reports the impact of the introduction of nano-grained quartz (SA = 325 m²/g) into the composition on the structure and properties of the ceramic glaze of the CMAS-Na₂O–K₂O system. The results were compared to the glaze which had an identical oxide composition, with a difference that quartz was introduced in the form of quartz powder with a much smaller specific surface area SA = 1.41 m²/g. Both glazes are characterized by a large part of the glassy phase, above 90% by volume. The results obtained show a higher arrangement of the continuous glassy phase structure in the glaze with the addition of nano-quartz. This glaze also shows significantly higher values for all measured mechanical properties. It seems that if, in the near future, new cheaper methods for the production of nano-quartz are developed, it will be a new interesting direction of research aimed at improving the parameters of glazes and glass-ceramic materials of CMAS type.     

Influence of Li2O–B2O3–SiO2 glass on the sintering behavior and microwave dielectric properties of BaO–0.15ZnO–4TiO2 ceramics

This paper reports the investigation of the performance of Li₂O–B₂O₃–SiO₂ (LBS) glass as a sintering aid to lower the sintering temperature of BaO–0.15ZnO–4TiO₂ (BZT) ceramics, as well as the detailed study on the sintering behavior, phase evolution, microstructure and microwave dielectric properties of the resulting BZT ceramics. The addition of LBS glass significantly lowers the sintering temperature of the BZT ceramics from 1150 °C to 875–925 °C. Small amount of LBS glass promotes the densification of BZT ceramic and improves the dielectric properties. However, excessive LBS addition leads to the precipitation of glass phase and growth of abnormal grain, deteriorating the dielectric properties of the BZT ceramic. The BZT ceramic with 5 wt% LBS addition sintered at 900 °C shows excellent microwave dielectric properties: ε_r=27.88, Q×f=14,795 GHz.     

Lithium concentration effect on crystallization kinetics and spectral properties of Cr-doped Li2O–K2O–Al2O3–B2O3 glass-ceramics

Alkali-aluminaborate glass-ceramics doped with Cr ions are synthesized by volume crystallization. According to non-isothermal DSC method three parallel processes occur in material: 2D Avrami-Yerofeev nucleation, 2D and 3D crystallization. During the heat treatment, the LiAl₇B₄O₁₇ crystalline phase is formed. With Li₂O content rising crystallinity of the material increases from 27 to 69% and the crystalline field strength Dq/B of Cr³⁺ increases from 2.25 to 3.55. The photoluminescence spectra possess intense bands at 685, 700, and 715 nm for glass with 6.8 mol.% Li₂O and higher and its decay kinetics is described by the sum of two exponentials. The maximum luminescence QY obtained is 50% at 16.1 mol.% Li₂O. The highest conversion efficiency of the 532 nm LED luminescence obtained by glass-ceramics with chromium is 10%. Thus, Cr-doped alkali-alumina-borate glass-ceramics are a promising material for use in the design of radiation sources for the red and NIR spectral regions.     

Modification of glass network and crystallization of CaO–Al2O3–MgO–SiO2 based glass ceramics with addition of iron oxide

Modification of glass network and crystallization process of a CaO–Al₂O₃–MgO–SiO₂ (CAMS) based glass ceramic to form diopside through addition of iron oxide were investigated using differential thermal analysis (DTA), Raman spectrum, X-ray diffraction, SEM and EBSD techniques. The experimental results showed that addition of Fe₂O₃ led to remarkable reductions in both the glass transition temperature (Tg) and crystallization temperature (Tp) of the CAMS glass ceramic. At addition level below 5 wt%, the Tg and Tp temperatures were 651°C and 903°C, respectively, and the crystallization only occurred on the surface of the glass ceramic samples. Increasing the addition level to 10 wt% and 15 wt%, not only led to reduction in the Tg and Tp temperatures to 643-641°C and 892-876°C, respectively, but also promoted the formation of crystalline diopside throughout the CAMS samples. Based on the results of Raman spectrums, it was confirmed that Fe₂O₃ addition reduced the strength of glass connection as a result of chemical reactions between the isolated Si–O tetrahedron and Fe³⁺ ion, forming Fe³⁺O₄–SiO₄, which can be regarded as Q₂ unit. And this is the first experimental evidence that proving the approach of Fe³⁺ mending glass network. Microstructural examination also identified the formation of large numbers of spherical Fe-enriched regions within the CAMS glass matrix as a result of the amorphous phase separation due to the Fe₂O₃ addition. The interfaces between the Fe-enriched regions and the glass matrix acted as preferred nucleation sites for the diopside, facilitating the crystallization. Crystallographic analysis using EBSD technique determined the <001> as the most favorite growth direction for the diopside crystals in the CAMS based glass ceramic.     

Preparation of glass–ceramic glazes in the SiO2–Al2O3–CaO–MgO–K2O–Na2O–ZnO system by variable content of ZnO

This paper is focused on glass–ceramic glazes from the SiO₂–Al₂O₃–CaO–MgO–K₂O–Na₂O system with ZnO additions (2.5, 5, 10, 15, 15, 20 and 25 wt%). The compositions were designed based on constant molar ratio of SiO₂/Al₂O₃. In the resulting glazes diopside (CaMg[Si₂O₆]), willemite (Zn₂SiO₄) and vitreous phase were identified by X-ray diffraction. Morphological and structural date of these glazes were supplementary determined by EPMA, FTIR and Raman Spectroscopy. DSC analysis was carried out to characterize thermal properties of the materials.     

Surface and bulk crystallization in Nd2O3–Al2O3–SiO2–TiO2 glasses

Neodymium aluminosilicate (Nd₂O₃–Al₂O₃–SiO₂; NdAS) glasses have been investigated for the effect of concentration of TiO₂ on the crystallization mechanism and for the effect of surface condition on crystal growth. NdAS glasses with 0–10 wt.% TiO₂ were heat-treated for nucleation and crystal growth and were examined for phase separation and morphology of surface crystals as well as for crystal growth rate. All the glasses exhibit surface crystallization, however, the glass having 8 wt.% TiO₂ also exhibits internal crystallization after a two-stage heat treatment. Surface crystallization was dependent on the condition of the glass surface and the amount of TiO₂. The crystal growth on the cut surface was faster than on the fractured surface and the growth rate in surface increased with increasing TiO₂. The phase separation found in NdAS glasses containing above 8 wt.% TiO₂, was confirmed to be an important factor controlling the internal crystallization process in Nd₂O₃–Al₂O₃–SiO₂–TiO₂ glasses.