Mechanical and dielectric properties of SiCf/SiC composites fabricated by PIP combined with CIP process

2D KD-1 SiC fiber fabrics were employed to fabricate SiC_f/SiC composites by an improved polymer infiltration and pyrolysis (PIP) process, combined with cold isostatic pressing (CIP). The effect of CIP process on the microstructure, mechanical and dielectric properties of SiC_f/SiC composites was investigated. The infiltration efficiency was remarkably improved with the introduction of CIP process. Compared to vacuum infiltration, the CIP process can effectively increase the infiltrated precursor content and decrease the porosity resulting in a dense matrix. Thus SiC_f/SiC composites with high density of 2.11 g cm⁻³ and low porosity of 11.3% were obtained at 100 MPa CIP pressure, together with an increase of the flexural strength of the composites from 89 MPa to 213 MPa. Real part (ε′) and the imaginary part (ε″) of complex permittivity of SiC_f/SiC composites increase and vary from 11.7-i9.7 to 15.0-i12.8 when the CIP pressure reaches 100 MPa.     

Mechanical properties of SiCf/SiC composites with alternating PyC/BN multilayer interfaces

Alternating pyrolytic carbon/boron nitride (PyC/BN)_n multilayer coatings were applied to the KD–II silicon carbide (SiC) fibres by chemical vapour deposition technique to fabricate continuous SiC fibre-reinforced SiC matrix (SiC_f/SiC) composites with improved flexural strength and fracture toughness. Three-dimensional SiC_f/SiC composites with different interfaces were fabricated by polymer infiltration and pyrolysis process. The microstructure of the coating was characterised by scanning electron microscopy, X–photoelectron spectroscopy and transmission electron microscopy. The interfacial shear strength was determined by the single-fibre push-out test. Single-edge notched beam (SENB) test and three-point bending test were used to evaluate the influence of multilayer interfaces on the mechanical properties of SiC_f/SiC composites. The results indicated that the (PyC/BN)_n multilayer interface led to optimum flexural strength and fracture toughness of 566.0?MPa and 21.5?MPa?m^1/2, respectively, thus the fracture toughness of the composites was significantly improved.     

Mechanical and dielectric properties of SiCf/BN/SiBCN composites via different synthesis technologies

SiC fibers reinforced SiBCN ceramic matrix composites (SiC_f/BN/SiBCN composites) were synthesized by direct chemical vapor infiltration (CVI), polymer infiltration pyrolysis (PIP) or chemical vapor infiltration combined with polymer infiltration pyrolysis (CVI + PIP). It is shown that the insertion of a continuous and dense SiBCN matrix via the CVI process improves the flexural strength and modulus. Interface debonding and fiber pullout happened with 50–100 nm BN interface in CVI and CVI + PIP SiC_f/BN/SiBCN composites. The relative complex permittivity was measured in X-band. Higher ε′′ values in CVI-containing composites can be observed, which can be attributed to the accumulation of C and SiC phases and a multilayer matrix. Strong electromagnetic wave attenuation ability was obtained with high dielectric loss.     

Effect of SiC interphase on the mechanical,high-temperature dielectric and high-temperature microwave absorption properties of the SiCf/SiC/Mu composites

In this study, SiC interphase was prepared via a precursor infiltration-pyrolysis process, and effects of dipping concentrations on the mechanical, high-temperature dielectric and microwave absorption properties of the SiC_f/SiC/Mu composites had been investigated. Results indicated that different dipping concentrations influenced ultimate interfacial morphology. The SiC interphase prepared with 5 wt% PCS/xylene solution was smooth and homogeneous, and no bridging between the fiber monofilament could be observed. At the same time, SiC interphase prepared with 5 wt% PCS/xylene solution had significantly improved mechanical properties of the composite. In particular, the flexural strength of the composite prepared with 5 wt% PCS/xylene solution reached 281 MPa. Both ε′ and ε′′ of the SiC_f/SiC/Mu composites were enhanced after preparing SiC interphase at room temperature. The SiC_f/SiC/Mu composite prepared with 5 wt% PCS/xylene solution showed the maximum dielectric loss value of 0.38 at 10 GHz. Under the dual action of polarization mechanism and conductance loss, both ε′ and ε′′ of the SiC_f/SiC/Mu composites enhanced as the temperature increased. At 700 °C, the corresponding bandwidth (RL ≤ ?5 dB) of SiC_f/SiC/Mu composites prepared with 5 wt% PCS/xylene solution can reach 3.3 GHz at 2.6 mm. The SiC_f/SiC/Mu composite with SiC interphase prepared with 5 wt% PCS/xylene solution is expected to be an excellent structural-functional material.     

Electromagnetic interference shielding and dielectric properties of SiCf/SiC composites containing pyrolytic carbon interphase

The SiC_f/SiC composites containing various thickness of pyrolytic carbon (PyC) interphase were prepared and their properties were investigated for electromagnetic interference (EMI) shielding applications in the frequency of 8.2–12.4 GHz. The composites containing 310 nm thickness (3.3 vol%) PyC interphase show an about 25 dB shielding effectiveness in the whole frequency band. Interestingly, the contribution of reflection to the EMI shielding effectiveness increases and the contribution of absorption decreases as the PyC interphase thickness increases.     

Micromechanical properties of vapour-exposed SiCf/BN/SiC ceramic-matrix composites

SiC_f/BN/SiC Ceramic-Matrix Composites are candidate materials for aero-engines, but their interphase stability after potential low-temperature water-vapour exposures during flight cycles is not well known. The examination of these composites exposed for 50, 250 and 500 h at low temperature (65 °C) and 95% relative humidity was therefore performed, in order to understand if resulting oxidation products affected the mechanical properties at the micro-scale. The composites were subject to fibre push-out tests to compare pristine from degraded composites. It was found that whilst the sample exposed for 50 h had no significant change from pristine, the samples exposed for 250 and 500 h had a clear decrease in interfacial shear strengths measured. Parallel studies also revealed that whilst damage was strongly localised, the diffusion of water within the composite was not fully complete at exposure times between 50 and 250 h. The permeability of the CMC was shown to be affected at longer exposure times where differences in mechanical performances even between tows and within tows were noted.     

Mechanical,thermal, and dielectric properties of SiCf/SiC composites reinforced with electrospun SiC fibers by PIP

Electrospun unidirectional SiC fibers reinforced SiC_f/SiC composites (e-SiC_f/SiC) were prepared with ∼10% volume fraction by polymer infiltration and pyrolysis (PIP) process. Pyrolysis temperature was varied to investigate the changes in microstructures, mechanical, thermal, and dielectric properties of e-SiC_f/SiC composites. The composites prepared at 1100 °C exhibit the highest flexural strength of 286.0 ± 33.9 MPa, then reduced at 1300 °C, mainly due to the degradation of electrospun SiC fibers, increased porosity, and reaction-controlled interfacial bonding. The thermal conductivity of e-SiC_f/SiC prepared at 1300 °C reached 2.663 W/(m∙K). The dielectric properties of e-SiC_f/SiC composites were also investigated and the complex permittivities increase with raising pyrolysis temperature. The e-SiC_f/SiC composites prepared at 1300 °C exhibited EMI shielding effectiveness exceeding 24 dB over the whole X band. The electrospun SiC fibers reinforced SiC_f/SiC composites can serve as a potential material for structural components and EMI shielding applications in the future.     

Mechanical properties and oxidation resistance of SiCf/CVI-SiC composites with PIP-SiC interphase

SiC coatings were successfully synthesized on SiC fibers by precursor infiltration and pyrolysis (PIP) method using polycarbosilane (PCS) as precursor. The morphology of as-fabricated coatings was observed by SEM, and its structure was characterized by XRD and Raman spectrum. The SiC fiber reinforced chemical vapor infiltration SiC (SiC_f/CVI-SiC) composites with PIP-SiC coatings as interphase were fabricated. And, the effects of PIP-SiC interphase on mechanical properties of composites were investigated. The experimental results point out that the coating is smooth and there is little bridging between fibers. The coating is amorphous with SiC and carbon micro crystals. The flexural strength of composites with and without PIP-SiC interphase is 220 and 100 MPa, respectively. And the composites with PIP-SiC interphase obviously exhibit a toughened fracture behavior. The oxidation resistance of composites with PIP-SiC interphase is much better than that of composites with pyrolytic carbon (PyC) interphase.     

Effect of intermediate heat treatment on mechanical properties of SiCf/SiC composites with BN interphase prepared by ICVI

SiC_f/SiC composites with BN interface were prepared through isothermal-isobaric chemical vapour infiltration process. Room temperature mechanical properties such as tensile, flexural, inter-laminar shear strength and fracture toughness (K_IC) were studied for the composites. The tensile strength of the SiC_f/SiC composites with stabilised BN interface was almost 3.5 times higher than that of SiC_f/SiC composites with un-stabilised BN interphase. The fracture toughness is similarly enhanced to 23 MPa m^1/2 by stabilisation treatment. Fibre push-through test results showed that the interfacial bond strength between fibre and matrix for the composite with un-stabilised BN interface was too strong (>48 MPa) and it has been modified to a weaker bond (10 MPa) due to intermediate heat treatment. In the case of composite in which BN interface was subjected to thermal treatment soon after the interface coating, the interfacial bond strength between fibre and matrix was relatively stronger (29 MPa) and facilitated limited fibre pull-out.     

Effect of SiC nanowires on the high-temperature microwave absorption properties of SiCf/SiC composites

SiC-nanowire-reinforced SiC_f/SiC composites were successfully fabricated through an in situ growth of SiC nanowires on SiC fibres via chemical vapour infiltration. The dielectric and microwave absorption properties of the composites were investigated within the frequency range of 8.2–12.4 GHz at 25–600 °C. The electric conductivity and complex permittivity of the composites displayed evident temperature-dependent behaviour and were enhanced with increasing temperature. The composites exhibited superior microwave absorption abilities with a minimum reflection loss value of ?47.5 dB at 11.4 GHz and an effective bandwidth of 2.8 GHz at 600 °C. Apart from the contribution of the interconnected SiC nanowire network and multiple reflections, the excellent microwave absorption performance was attributed to dielectric loss that originated from SiC nanowires with abundant stacking faults and heterostructure interfaces. Results suggested that the composites are promising candidates for high-temperature microwave absorbing materials.     

Mechanical properties of the SiCf/SiC composites reinforced with KD-I and KD-II fibers fabricated assisted by a microwave heating method

SiC_f/SiC composites using KD-I and KD-II SiC fibers braided preforms as the reinforcements were fabricated by applying the polymer impregnation and pyrolysis (PIP) technique with a microwave heating assistance. The microwave heating temperature was 1100 °C, 1200 °C, 1300 °C, and 1400 °C, respectively. Microstructures, flexure properties, and fracture behaviors of the composites were investigated. The KDIISiC_f/SiC composites exhibited higher flexure properties and improved non-brittle fracture characteristics than those of the KD-ISiC_f/SiC composites. The differences in the flexural properties, fracture behaviors and microstructures between the KD-I and KDIISiC_f/SiC composites were discussed based on the tensile properties of the SiC filaments and the interfacial bonding statues in the composites.     

Mechanical properties and microstructure evolution of KD-SA SiCf/BN/SiC CMCs oxidized at different temperatures

Silicon carbide fiber-reinforced SiC ceramic matrix composites (SiC_f/SiC CMCs) based on a domestic KD-SA SiC fiber were exposed to a wet oxygen atmosphere for 135 h at 800, 1100, and 1300°C. The evolution of the microstructure and mechanical properties of SiC_f/SiC CMCs have been systematically investigated following oxidation. For weight change, CMC-1300 showed the greatest gain (0.394%), followed by CMC-1100 (0.356%) and CMC-800 (0.149%). The volatilization of boron oxide (B₂O₃) combined with the slight oxidation of the SiC matrix at 800°C caused crack deflection and fiber pull-out. The complete dissipation of the interphase could be found when the oxidation temperature increases to 1100°C, generated a fracture surface with brittle fracture characteristics. At 1300°C, crystalline SiO₂ hindered oxygen diffusion, with evidence of fiber pull-out. Based on thermodynamic calculations and microscopic observations, we propose a mechanism to explain the thermal degradation of SiC_f/SiC CMCs. This work offers valuable guidance for the fabrication of SiC_f/SiC CMCs that are suitable for high-temperature applications.     

Enhanced mechanical and dielectric properties of SiCf/SiC composites with silicon oxycarbide interphase

SiC_f/SiC composites with silicon oxycarbide (SiOC) interphase were successfully prepared using silicone resin as interphase precursor for dip-coating process and polycarbosilane as matrix precursor for PIP process assisted with hot mold pressing. The effects of SiOC interphase on mechanical and dielectric properties were investigated. XRD and Raman spectrum results show that SiOC interphase is composed of silicon oxycarbide and free carbon with a relatively low crystalline degree. The surface morphology of SiC fibers with SiOC interphase is smooth and homogeneous observed by SEM. The flexural strength and failure displacement of SiC_f/SiC composites with SiOC interphase vary with the thickness of interphase and the maximum value of flexural strength is 289 MPa with a failure displacement of 0.39 mm when the thickness of SiOC interphase is 0.25 µm. The complex permittivity of the composites increases from 8.8-i5.7 to 9.8-i8.3 with the interphase thicker.     

The design of zirconium and hafnium germanate interphase in SiCf/SiC composites

Unidirectional SiC_f/SiC minicomposites with SiC matrix derived by polymer-impregnation pyrolysis (PIP), reinforced with SiC fibers coated with zirconium or hafnium germanate were fabricated. Microdebonding indentation tests for SiC_f/SiC composites with one- and multilayered germanate interphase were performed. Interfacial shear stress depending on the number of germanate interfacial layers and morphology was determined. The microstructure of the minicomposites and indented fracture surfaces were studied by scanning electron microscopy (SEM). It was stated that an increase in the number of interfacial coatings leads to a decrease in the interfacial frictional stress in SiC_f/SiC minicomposites with germanate interphases. The key factor of interphase weakening is the formation of a weak interlayer bonding within the interphase but not germanate layered crystal structure itself. Thus, bonding at the fiber/matrix boundary could be regulated by the number of layers of ZrGeO₄ or HfGeO₄ in the interphase zone.     

Fabrication and performance of mini SiC/SiC composites with an electrophoresis-deposited BN fiber/matrix interphase

The feasibility of fabricating a BN matrix/fiber interphase of SiC/SiC composites via electrophoresis deposition (EPD) was investigated based on the simplicity and non-destructiveness of the process and the excellent interfacial modification effects of BN. The BN suspension and SiC fiber surface properties were both adjusted to generate suitable conditions for the EPD process of the BN interphase. Next, the deposition dynamics and mechanism were studied under different deposition voltages and time, and the relationship between the deposition morphology of the BN interphase and mechanical properties of the fabricated mini SiC/SiC composites were also discussed. After oxidation at high temperature (600–1000 ℃), the mechanical properties of the mini SiC/SiC composites were studied to verify the oxidation resistance effect of the EPD-deposited BN interphase, whose oxidation resistance mechanism was briefly analyzed as well.     

In-situ formation of Ti3SiC2 interphase in SiCf/SiC composites by molten salt synthesis

Titanium silicon carbide (Ti₃SiC₂) film was synthesized by molten salt synthesis route of titanium and silicon powder based on polymer-derived SiC fibre substrate. The pre-deposited pyrolytic carbon (PyC) coating on the fibre was utilized as the template and a reactant for Ti₃SiC₂ film. The morphology, microstructure and composition of the film product were characterized. Two Ti₃SiC₂ layers form the whole film, where the Ti₃SiC₂ grains have different features. The synthesis mechanism has been discussed from the thickness of PyC and the batching ratio of mixed powder respectively. Finally, the obtained Ti₃SiC₂ film was utilized as interphase to prepare the SiC fibre reinforced SiC matrix composites (SiC_f/Ti₃SiC₂/SiC composites). The flexural strength (σ_F) and fracture toughness (K_IC) of the SiC_f/Ti₃SiC₂/SiC composite is 460 ± 20 MPa and 16.8 ± 2.4 MPa?m^1/2 respectively.     

Microstructure and mechanical properties of Si3N4f/BN composites with BN interphase prepared by chemical vapor deposition of borazine

The boron nitride (BN) interphase of silicon nitride (Si₃N₄) fiber-reinforced BN matrix (Si₃N_4f/BN) composites was prepared by chemical vapor deposition (CVD) of liquid borazine, and the microstructure, growth kinetics and crystallinity of the BN coating were examined. The effects of coating thickness on the mechanical strength and fiber/matrix interfacial bonding strength of the composites were then investigated. The CVD BN coating plays a key role in weakening the interfacial bonding condition that improves the mechanical properties of the composites. The layering structure of the BN coating promotes crack propagation within the coating, which leads to a variety of toughening mechanisms including crack deflection, fiber bridging and fiber pull out. Single-fiber push-out experiments were performed to quantify the fiber/matrix bonding strength with different coating thicknesses. The physical bonding strength due to thermal mismatch was discussed.     

Mechanical properties and strengthening mechanism of SiCf/SiC mini-composites modified by SiC nanowires

The effects of the SiC nanowires (SiCNWs) and PyC interface layers on the mechanical and anti-oxidation properties of SiC fiber (SiC_f)/SiC composites were investigated. To achieve this, the PyC layer was coated on the SiC_f using a chemical vapour infiltration (CVI) method. Then, SiCNWs were successfully coated on the surface of SiC_f/PyC using the electrophoretic deposition method. Finally, a thin PyC layer was coated on the surface of SiC_f/PyC/SiCNWs. Three mini-composites, SiC_f/PyC/SiC, SiC_f/PyC/SiCNWs/SiC, and SiC_f/PyC/SiCNWs/PyC/SiC, were fabricated using the typical precursor infiltration and pyrolysis method. The morphologies of the samples were examined using scanning electron microscopy and energy dispersive X-ray spectrometry. Tensile and single-fibre push-out tests were carried out to investigate the mechanical performance and interfacial shear strength of the composites before and after oxidization at 1200 °C. The results revealed that the SiC_f/PyC/SiCNWs/SiC composites showed the best mechanical and anti-oxidation performance among all the composites investigated. The strengthening and toughening is mainly achieved by SiCNWs optimization of the interfacial bonding strength of the composite and its own nano-toughening. On the basis of the results, the effects of SiCNWs on the oxidation process and retardation mechanism of the SiC_f/SiC mini-composites were investigated.     

Phase-field simulation of microscale crack propagation/deflection in SiCf/SiC composites with weak interphase

To understand the microscale toughening mechanism, the crack propagation, and stress–strain response of unidirectional SiC_f/SiC composites with h-BN interphase under transverse and longitudinal tension are investigated by a promising micromechanical phase field (PF) method along with representative volume element. Of much interest, the calculation results are well consistent with the available experimental results. With a strong dependence on the interphase strength, the toughening mechanisms during crack propagation are well presented, for example, fiber pull-out, crack deflection, and interphase debonding. Furthermore, the longitudinal tensile strength of SiC_f/SiC composites increases with decreasing the interphase strength, where only a weak enough interphase can result in a significant crack deflection by its cracking. In particular, the ratio of the interphase strength along fibers to the matrix strength should be less than 1.254 to ensure crack deflection in the interphase and fiber pull-out. Moreover, the transverse tensile strength of SiC_f/SiC composites reaches a maximum with increasing the interphase thickness into the range of 0.25–0.5 µm.     

Fine study of hierarchical interphase constructed by boron nitride and carbon nanotubes in SiCf/SiC composites

A fine study of the interfacial part in the silicon carbide fiber (SiC_f) reinforced silicon carbide (SiC) composites was conducted by transmission electron microscopy. The boron nitride (BN) and carbon nanotubes (CNTs) were progressively coated on the SiC_f by chemical vapor deposition method to form a hierarchical structure. Three composites with different interfaces, SiC_f–CNTs/SiC, SiC_f@BN/SiC, and SiC_f@BN–CNTs/SiC, were fabricated by polymer infiltration and pyrolysis method. The interfaces and microstructures of the three composites were carefully characterized to investigate the improvement mechanism of strength and toughness. The results showed that BN could protect the surface of SiC_f from corrosion and oxidation so that improved the possibility of debonding and pullout. CNTs could avoid the propagation of cracks in the composites so that improved the damage resistance of the matrix. The synergistic reinforcement brought by BN and CNTs interfaces made the SiC_f@BN–CNTs/SiC composites with a tensile fracture strength as high as 359 MPa, with an improvement of 23% compared to that of SiC_f@BN/SiC.