Determination of uronic acids in isolated hemicelluloses from kenaf using diffuse reflectance infrared fourier transform spectroscopy (DRIFTS) and the curve-fitting deconvolution method

Hemicellulose samples were isolated from kenaf (Hibiscus cannabinus L.). Hemicellulosic fractions usually contain a variable percentage of uronic acids. The uronic acid content (expressed in polygalacturonic acid) of the isolated hemicelluloses was determined by diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and the curve-fitting deconvolution method. A linear relationship between uronic acids content and the sum of the peak areas at 1745, 1715, and 1600 cm(-1) was established with a high correlation coefficient (0.98). The deconvolution analysis using the curve-fitting method allowed the elimination of spectral interferences from other cell wall components. The above method was compared with an established spectrophotometric method and was found equivalent for accuracy and repeatability (t-test, F-test). This method is applicable in analysis of natural or synthetic mixtures and/or crude substances. The proposed method is simple, rapid, and nondestructive for the samples.     

A simple method for the determination of clinoptilolite in natural zeolite rocks

A reliable and apparent method based on diffuse reflectance FT i.r. spectroscopy (DRIFTS) for the quantitative determination of clinoptilolite in natural zeolites has been developed. The technique provides a simple and time-saving analysis of the minerals when compared with the powder X-ray diffraction (XRD) method and/or the conventional pellet preparation i.r. technique. Because of the complex structure of the natural minerals, the reliability of the analysis is improved further by combining the XRD and DRIFTS methods. In this study, the clinoptilolite concentration of natural zeolites mined in the US and Hungary was determined by both techniques. The results were compared, and good agreement was found.     

Carbon isotope composition of dissolved humic and fulvic acids in the Tokachi River system

This study reports carbon isotopic ratios (Δ(14)C and δ(13)C) of dissolved humic and fulvic acids in the Tokachi River system, northern Japan. These acids have a refractory feature and they represent the largest fraction of dissolved organic matter in aquatic environments. The acids were isolated using the XAD extraction method from river water samples collected at three sites (on the upper and lower Tokachi River, and from one of its tributaries) in June 2004 and 2005. δ(13)C values were -27.8 to -26.9 ‰ for humic and fulvic acids. On the other hand, the Δ(14)C values ranged from -247 to +26 ‰ and the average values were -170 ± 79 ‰ for humic acid and -44 ± 73 ‰ for fulvic acid. The difference was attributed to the residence time of fulvic acid in the watershed being shorter than that of humic acid. The large variation suggested that humic substances have a different pathway in each watershed environment.     

Rapid delineation of humic and non-humic organic matter fractions in water

Dissolved organic matter (DOM) in water is often characterized by aggregate parameters like dissolved organic carbon (DOC). DOM from conventional surface water treatment plant in Northern New Jersey was isolated and fractionated using resin adsorption chromatography into six different fractions, which were operationally categorized as hydrophobic acid, hydrophobic neutral, hydrophobic base, hydrophilic acid, hydrophilic neutral and hydrophilic base. The spectral fluorescent signatures (SFS) technique was developed for the quantitative identification of the six fractions by post-processing analysis that includes a statistical model. The SFS is the total sum of emission spectra of a sample at different excitation wavelengths, recorded as a matrix of fluorescent intensity in coordinates of excitation and emission wavelengths, in a definite spectral window. High sensitivity and rapid identification and quantification of DOM fractions are among the main features of the technique. Since hydrophobic and hydrophilic substances are considered more humic and non-humid in nature, respectively, the technique provided an opportunity to rapidly delineate source waters in terms of such categories.     

On-the-fly fluorescence lifetime detection of humic substances in capillary electrophoresis

On-the-fly fluorescence lifetime detection was investigated as a tool for studying humic substances in capillary zone electrophoresis (CZE). Humic substances are complex, heterogeneous mixtures of natural products that tend to migrate in a single, broad CZE peak. The intrinsic fluorescence lifetime of five humic substances from the International Humic Substances Society (IHSS) was monitored using excitation at 488 or 364 nm to produce intensity-lifetime electropherograms for each of the substances. Each frequency-domain lifetime measurement, collected at subsecond intervals during the CZE run, contains the equivalent of a complete decay profile. Lifetime analysis of each decay profile was used to construct a lifetime-resolved electropherogram for each lifetime component, from which the variation in relative intensity contributions of each lifetime across the broad CZE peak could be determined. Absorption spectra, fluorescence excitation-emission spectra, and lifetime profiles of batch solutions of the samples were determined as well. It was found that, whereas absorption and fluorescence spectral characteristics tended to discriminate between humic acids and fulvic acids, the batch solution lifetime profiles discriminated instead between samples from different sources, regardless of fraction. On-the-fly lifetime detection provided a more detailed view of the fluorescence decay of the samples, including greater resolution of lifetimes for two of the fulvic acids and greater discrimination among samples based on lifetime profiles across the CZE peaks.     

Evaluation of toxicity of the pesticides, chlorpyrifos and arsenic, in the presence of compost humic substances in aqueous systems

An improved understanding of pesticide toxicity in natural systems can have important consequences for pesticide management and remediation strategies for contaminated areas. The interaction between humic substances extracted from compost natural organic matter and both organic and inorganic pesticides was evaluated for its effect on the toxicity of pesticides in the aqueous phase. The toxicity of contaminants was measured using the Microtox toxicological bioassay. Solutions containing concentrations ranging from 2 to 42 mg C/l of humic substance extracted from a South Texas compost were added to concentrations of the organic pesticide, chlorpyrifos, and toxicity reduction ranging from 50 to 100% was demonstrated. Different concentrations of arsenic ranging from 0.5 to 5 mg/l were also associated with three different concentrations of humic substances and the arsenic toxicity was consistently reduced by a factor of 100%. These results demonstrate a significant relationship between humic substance interactions with organic and inorganic pesticides, and pesticide toxicity in natural systems, and may also suggest a mechanism for pesticide toxicity reduction in natural waters through compost humic addition for contaminated groundwaters and surface waters.     

Dependence of the migration ability of plutonium and americium in soils on additions of natural and modified organic compounds

The nature and content of modified humic acid derivatives influence the intensity of the recovery of Pu, Am, and C_org from soddy podzolic soil with distilled water. Under the dynamic conditions, these radionuclides are recovered more intensely in the presence of carboxylated humic acids, compared to the hydroxymethylated derivatives. When soils with the introduced modified humic acid derivatives are subjected to prolonged washing with distilled water, the radionuclides undergo redistribution within the columns, suggesting their migration. Under the action of dissolved organic substances isolated from soils (low-molecular-weight nonspecific organic compounds and fulvic acids), the radionuclide migration in soils occurs still more intensely. In the course of soil column washing with an aqueous phase containing the dissolved organic matter, Pu and Am pass into the mobile state to a greater extent than in washing the soils with distilled water.     

New method for pollen identification by FT-IR spectroscopy

A new methodology for identification of pollen was developed based on FT-IR spectroscopy. Pollen samples of twenty different plant species were collected and the diffuse reflectance infrared Fourier transform (DRIFTS) and KBr pellet spectra were recorded. Libraries of spectra were created. Spectra of unknown plant origin pollen were recorded and compared with those of the corresponding pollen library and the match value was measured automatically using the appropriate software (OMINC ver. 3.1). From the same pollen samples, microscopic slides were prepared and the photographs of the pollen grains were used as a second comparison method. Using light microscopy, the pollen identification is usually limited to the family or generic name, while FT-IR spectroscopy can distinguish species belonging to the same genus. This method is simple and fast, and when the DRIFTS technique is used the sample is not destroyed.     

Specular reflection and diffuse reflectance spectroscopy of soils

Studies on the occurrence and effects of specular reflection in midinfrared spectra of soils have shown that distortions due to specular reflection occur for both organic (humic acid) and non-organic fractions (carbonates, silica, ashed fraction of soil). The results explain why the spectra of CaCO(3) in limed soils do not match published spectra and offer an explanation as to why the presence of inorganic C interferes with the development of calibrations for organic C. These results may also have implications for the use of mid-infrared spectra for quantitative and qualitative analysis of soils. For example, libraries of spectra collected by means other than diffuse reflectance would be largely useless for comparing mineral spectra to soil spectra. To obtain the best results with forages and grains, it is necessary to develop separate calibrations for different products, but this has not seemed to be a problem for diverse sets of soil samples with C contents of 0 to 5%. Mid-infrared calibrations have also appeared to be more robust than the corresponding near-infrared calibrations in that fewer outliers are found. However, the results discussed here indicate that at least for some soil types (e. g., large differences in mineralogy or C contents), separate calibrations may be necessary.     

Decomposition of toxic pollutants in landfill leachate by ozone after coagulation treatment

This study deals with evaluation of organic matter from Mexico City waste sanitary landfill leachate of Bordo Poniente (including domestic and industrial) by ozonation after a coagulation treatment with Fe2(SO4)(3) (2.5 g/L at pH 4-5). The content of humic substances after the coagulation treatment decreases up to 70%. Then leachate obtained from a solid with initial COD=1511 mg/L and the pH 8.5 was treated by ozone. The aqueous samples by a UV-vis and HPLC technique were analyzed. The partial identification of the initial composition of the organic matter as well as of intermediates and final products was carried out after the extraction of the initial and ozonated leachate with benzene, chloroform:methanol (2:1) and hexane. Then the extracts with a gas chromatograph with mass detector and FID were analyzed. In the HPLC results we identify malonic and oxalic acids. The initial concentrations of these acids were 19 mg/L and 214 mg/L, respectively. The oxalic acid is formatted and accumulated in ozonation. The obtained results show that the color disappears (visually) at 100% during 5 min of ozonation. The organic substances, extracted with chloroform-methanol, may be destructed during 15 min of ozonation; the organic matter, extracted with benzene, destructs completely by ozone during 5 min, and the organic compounds extracted with hexane have a low ozonation rate. The toxic compounds presented in leachate decompose completely during 15 min of ozonation. The ozonation rate constants for each group of organics (as observed constants) were calculated applying simplified mathematical model and the recurrent least square method using the program MATLAB 6.5.     

Determination of humic acids content in composts by means of near- and mid-infrared spectroscopy and partial least squares regression models

Humic acids are part of the stable organic matter fraction in soils and composts. Due to their favorable properties for soils and plants, and their role in carbon sequestration, they are considered a quality criterion of composts. Time-consuming chemical extraction of humic acids and the inherent source of errors require alternative approaches for humic acids quantification. Different measurement techniques in the mid-infrared (MIR: KBr pellet technique) and near-infrared (NIR: fiber probe as well as an integrating sphere with a sample rotator) regions were applied. Partial least squares regression (PLSR) models based on infrared spectra were developed to determine humic acids contents in composts. As the wavenumber regions used (NIR: 6105-5380 cm(-1) and 4360-4220 cm(-1), MIR: 1745-1685 cm(-1) and 1610-1567 cm(-1)) represent different molecular vibrations, the importance of the methylene-group-derived vibrations for the NIR models is discussed. The correlation coefficients obtained for the KBr pellet technique, the NIR fiber probe technique, and the NIR integrating sphere (r = 0.94, 0.93, and 0.94) and the root mean square errors of cross-validation (RMSECV = 2.2% organic dry matter (ODM), 2.5% ODM, and 2.2% ODM) make the models appropriate for application in composting practice.     

Effect of humic substances on Cu(II) solubility in kaolin-sand soil

The type and amount of organic matter present in industrially contaminated soils will influence the risk they pose. Previous studies have shown the importance of humic and fulvic acids (FAs) (important components of soil organic matter) in increasing the solubility of toxic metals but were not carried out using toxic metal levels and the pH range typical of industrially contaminated soils. This study investigated the influence of three humic substances (HSs: humates, fulvates and humins) on the solubility of copper(II) ions in kaolinitic soil spiked with Cu at levels representative of industrially contaminated soil. Humates, fulvates and humin were extracted from Irish moss peat, and controlled pH batch leaching tests were conducted on an artificial kaolin-sand soil that was spiked with each. Further leaching tests were conducted on soil spiked with each HS and copper nitrate. Dissolved organic contents were determined by titration and total and free aqueous copper concentrations in the leachate were measured using AAS and ion selective electrode (ISE) potentiometry respectively (dissolved complexed copper levels were determined by difference). It was found that humates and fulvates are partially sorbed by the soil, probably by chemisorption on positively charged gibbsite (Al-hydroxide) sites in the kaolinite. The addition of 340 mg/kg Cu(II) ions did not significantly affect the amount of humate or fulvate sorbed. Dissolved humates and fulvates form soluble complexes with copper over the pH range 3-11. However, in the presence of kaolinite, soluble copper humates and fulvates are unable to compete with the kaolinite for Cu ions at pH 6-7. Above pH 8, humate and fulvate complexes are the only forms of dissolved Cu. Humin is largely insoluble and has little effect on Cu mobility between pH 2 and 12. The implication of this study is that measurement of total soil organic content and water leaching tests should be a standard part of contaminated site investigation.     

Direct in situ measurements of labile inorganic and organically bound metal species in synthetic solutions and natural waters using diffusive gradients in thin films

The emerging technique of DGT (diffusive gradients in thin films) is shown to be capable of performing new speciation measurements in situ in natural waters. In DGT, metals are bound to a resin layer after passing through a well-defined diffusion layer. Cd was measured in solutions containing glycine, EDTA, and fulvic (FA) and humic acids (HA) by atomic absorption spectroscopy (AAS), anodic stripping voltammetry (ASV), and DGT. DGT measured similar labile fractions to ASV, with detailed differences being consistent with a thicker diffusion layer allowing more dissociation of labile complexes and a slower diffusion of FA and HA complexes through the gel. When single measurements are made in complex solutions with DGT, precise quantification is impossible due to uncertainties concerning the distribution of species with different diffusion coefficients. A new procedure was proposed based on the advantage of DGT of being able to control the pore size of the diffusive gel layer. Small (inorganic) species diffuse freely through all gels but larger FA and HA (organic) complexes diffuse less freely in more constrained gels. When measurements were made on known solutions of Cu and FA or HA, it was possible to quantify the inorganic and organic species separately. They agreed well with predictions made using the WHAM speciation code. Multiple DGT units were also deployed in situ in a stream with high dissolved organic carbon (14.6 mg/L). The systematic differences between the devices with different gel compositions enabled determination, for the first time, of the in situ concentrations of both labile inorganic and organic species in natural water. A single DGT device with a constrained gel can be used to quantify inorganic species directly, providing absolute accuracy is not required. This ability of DGT to measure well-defined fractions of metals in situ using a simple device gives it considerable potential as a regulatory tool. A direct speciation measurement may be preferable to modeling approaches which require diverse input data that are difficult to determine.     

Stable-isotope dimethylation labeling combined with LC-ESI MS for quantification of amine-containing metabolites in biological samples

One of the challenges associated with metabolome profiling in complex biological samples is to generate quantitative information on the metabolites of interest. In this work, a targeted metabolome analysis strategy is presented for the quantification of amine-containing metabolites. A dimethylation reaction is used to introduce a stable isotopic tag onto amine-containing metabolites followed by LC-ESI MS analysis. This labeling reaction employs a common reagent, formaldehyde, to label globally the amine groups through reductive amination. The performance of this strategy was investigated in the analysis of 20 amino acids and 15 amines by LC-ESI MS. It is shown that the labeling chemistry is simple, fast (<10-min reaction time), specific, and provides high yields under mild reaction conditions. The issue of isotopic effects of the labeled amines on reversed-phase (RP) and hydrophilic interaction (HILIC) LC separations was examined. It was found that deuterium labeling causes an isotope effect on the elution of labeled amines on RPLC but has no effect on HILIC LC. However, 13C-dimethylation does not show any isotope effect on either RPLC or HILIC LC, indicating that 13C-labeling is a preferred approach for relative quantification of amine-containing metabolites in different samples. The isotopically labeled 35 amine-containing analogues were found to be stable and proved to be effective in overcoming matrix effects in both relative and absolute quantification of these analytes present in a complicated sample, human urine. Finally, the characteristic mass difference provides additional structural information that reveals the existence of primary or secondary amine functional groups in amine-containing metabolites. As an example, for a human urine sample, a total of 438 pairs of different amine-containing metabolites were detected, at signal-to-noise ratios of greater than 10, by using the labeling strategy in conjunction with RP LC-ESI Fourier-transform ion cyclotron resonance MS.     

Radiogenic 234U and 210Po in humus acids of dyctionemic shale

Radiochemical analysis is made of different fractions of humic and fulvic acids separated from organic matter of graptolitic argillite (dyctionemic shale) of the Baltic basin. The relation between the decalcination of humates and fulvates and the isotopic composition of U is studied. The tightness of binding to humus substances, including humin, is different for ²³⁸U and ²³⁴U, which is probably due to preferential stabilization of the radiogenic uranium in the oxidation state +4. Based on the experiments on precipitation of humates at pH 0–2, it is suggested that the thiol groups of humic acids are involved in chemical binding of ²¹⁰Po. Experiments on partial decalcination of humates in 1 M HNO₃ revealed stronger binding of the radiogenic Po as compared to ^208,209Po. The results were interpreted in terms of the known models.     

Double-disk solid-phase extraction: simultaneous cleanup and trace enrichment of herbicides and metabolites from environmental samples

Phenylurea and triazine herbicides, including some metabolites, were isolated from water and soil extracts by solid-phase extraction using a layered system of two extraction disks, a method called double-disk solid-phase extraction. The first disk consisted of strong anion exchange (SAX) of 10-micron styrene divinylbenzene (SDB) particles embedded in Teflon, and the second disk was a C18 disk of 10-micron particles also embedded in Teflon. A volume of 500 mL of water or aqueous soil extract is passed through the layered system with the SAX disk first. The purpose of the SAX disk is to remove the humic and fulvic acids from the water or aqueous soil extract by ion exchange through their carboxyl groups. Even during methanol elution of herbicides, the humic substances remain bound to the SAX disk with > 85% retention. Elution with methanol results in more than 90% recovery of the herbicides from the layered extraction disks. Removal of the humic and fulvic acids results in greater sensitivity for diode array detection quantitation (0.05 micrograms/L for herbicides) by substantially reducing the absorbance of the humic peak on the LC chromatogram. The herbicides adsorb to the SAX disk either through hydrogen bonding to the anion-exchange sites or by hydrophobic interaction with the SDB surface of the anion-exchange disk. The method was tested for the analysis of natural water samples from the Mississippi Embayment, a cotton-growing area of the southeastern United States.     

Identification and quantification of 77 pesticides in groundwater using solid phase coupled to liquid-liquid microextraction and reversed-phase liquid chromatography

This paper describes a method for the extraction, separation, identification, and quantification of 77 pesticides (neutral, acidic, and basic) including some s-triazine metabolites. The method is appropriate for organically (e.g. with humic acids) highly loaded groundwater samples. A comparative study of a pH-controlled mixed solid phase (LiChroprep RP18/LiChrolut EN) extraction with different desorption solvents (acetonitrile or acetonitrile and dichloromethane/methanol) is elaborated. A subsequent liquid-liquid microextraction reduces matrix effects. The pesticides in the sample are separated using RP-HPLC, detected, and identified by diode array. The efficiency is illustrated on a natural groundwater sample from a phreatic aquifer.     

Selective ionization of dissolved organic nitrogen by positive ion atmospheric pressure photoionization coupled with Fourier transform ion cyclotron resonance mass spectrometry

Dissolved organic nitrogen (DON) comprises a heterogeneous family of organic compounds that includes both well-known biomolecules such as urea or amino acids and more complex, less characterized compounds such as humic and fulvic acids. Typically, DON represents only a small fraction of the total dissolved organic carbon pool and therefore presents inherent problems for chemical analysis and characterization. Here, we demonstrate that DON may be selectively ionized by atmospheric pressure photionization (APPI) and characterized at the molecular level by Fourier transform ion cyclotron resonance mass spectrometry. Unlike electrospray ionization (ESI), APPI ionizes polar and nonpolar compounds, and ionization efficiency is not determined by polarity. APPI is tolerant to salts, due to the thermal treatment inherent to nebulization, and thus avoids salt-adduct formation that can complicate ESI mass spectra. Here, for dissolved organic matter from various aquatic environments, we selectively ionize DON species that are not efficiently ionized by other ionization techniques and demonstrate significant signal-to-noise increase for nitrogen species by use of APPI relative to ESI.     

Extraction of extracellular polymeric substances from aerobic granule with compact interior structure

Extracellular polymeric substances (EPS) were extracted from aerobic granules of compact interior structure using seven extraction methods. Ultrasound followed by the chemical reagents formamide and NaOH outperformed other methods in extracting EPS from aerobic granules of compact interior. The collected EPS revealed no contamination by intracellular substances and consisted mainly of proteins, polysaccharides, humic substances and lipids. The quantity of extracted proteins exhibited a weak correlation with quantity of extracted carbohydrates but no correlation with quantity of extracted humic substances. The total polysaccharides/total proteins (PN/PS) ratios for sludge flocs were approximately 0.9 regardless of extraction method. Protein content was significantly enriched in the granules, producing a PN/PS ratio of 3.4-6.2. This experimental result correlated with observations using excitation-emission matrix (EEM) and confocal laser scanning microscope technique. However, detailed study disproved the use of EEM results as a quantitative index of extracted EPS from sludge flocs or from granules.     

Analysis of diffusion coefficient distributions in humic and fulvic acids by means of diffusion ordered NMR spectroscopy

The use of the computer program CONTIN to analyze pulsed-field gradient NMR (PFG-NMR) data for several standard humic and fulvic acids is described. An advantage of PFG-NMR analysis is that integration of different spectral regions provides a picture of how the diffusion coefficients vary with functional group composition for a given sample. Using prior knowledge of the sample and the principle of parsimony, CONTIN approximates a solution to the inverse Laplace transform applied to the decay of peak intensity with gradient area in the PFG-NMR experiment. Thus, a continuous distribution of diffusion coefficients is resolved for the polydisperse humic and fulvic acids. The results of the CONTIN analyses are in the form of a distribution function and a two-dimensional DOSY plot. The 2D DOSY spectrum displays chemical shifts along one axis and diffusion coefficients along the other, while a number-average diffusion coefficient, D(N), a weight-average diffusion coefficient, D(W), and a most probable diffusion coefficient, D(P), are realized from the diffusion coefficient distribution. For all spectral regions of each humic sample, D(W) was greater than D(N), which in turn was greater than or equal to the D(P), suggesting that the diffusion coefficient distribution is weighted toward smaller, more rapidly diffusing molecules. Polydispersities, estimated from the ratio D(W)/D(N), were less than the reported M(W)/M(N) values for similar humic substances. Thus, the D(W)/D(N) ratio obtained by CONTIN analysis of PFG-NMR data can be at least a qualitative, and at best a semiquantitative, indication of the polydispersity of the humic sample, but should not be used as a quantitative measure of polydispersity.