激光熔覆原位TiC/Fe复合涂层增强相形成机制研究

激光熔覆技术在制备原位自生颗粒增强金属基耐磨复合涂层领域具有良好的应用前景。以廉价钛铁和石墨为熔覆粉末,采用横流CO2激光器在低碳钢基体上制备了TiC增强Fe基复合涂层,并对涂层物相组织和TiC增强相的形成机制进行了研究。结果表明,增强相TiC通过原位冶金反应形成,在熔体的冷却过程中析出长大,具有树枝晶和鱼骨状两种形态。树枝晶形态的TiC为熔体先析出相,其生长形态受界面前沿成分过冷和晶体生长习性控制。鱼骨状TiC由δ-Fe和TiC的准共晶反应形成,溶质原子扩散特征和晶面能决定了共晶TiC的最终鱼骨状形貌。均匀弥散分布的TiC增强相有助于提高涂层的耐磨损性能。     

Microstructure and wear resistance of laser clad TiC particle reinforced coating

Abstract

A TiC–Ni alloy composite coating was clad to 1045 steel substrate using a 2 kW CO₂ laser. The microstructural constituents of the clad layer arefound to be γ-Ni and TiC_p in the dendrites, and afine eutectic of γ-Ni plus (Fe,Cr)₂₃C₆ in the interdendritic areas. Partial dissolution and aggregation of the original TiC particles during melting of the Ni alloy and their growth during resolidification on cooling are observed. The TiC particles offer significantly enhanced wear resistance, the degree of wear depending primarily on the debonding removal of the particles.

MST/3018     

Ti811合金表面激光熔覆Ti2Ni+TiC+Al2O3+CrxSy复合涂层的组织和性能

以TC4+Ni45+Al₂O₃+MoS₂+Y₂O₃混合粉末为熔覆材料,采用同轴送粉技术在Ti811合金表面进行激光熔覆制备复合涂层,使用SEM、EDS和XRD等手段分析了涂层的微观组织,测试了涂层的显微硬度和摩擦磨损性能。结果表明,在激光熔覆过程中Ti811合金中的Ni和C分别与Ti发生反应,原位生成金属间化合物Ti₂Ni和硬质增强相TiC;MoS₂分解后S与Cr发生硫化反应生成了软质润滑相Cr_xS_y。网状形态的Ti₂Ni、近球状和枝晶形态的TiC以及点状的Al₂O₃,均匀分布在熔覆层中。硬质相强化和软质相润滑的共同作用,使激光熔覆层具有较高的显微硬度和较优良的耐磨性能。激光功率为900 W的熔覆层其平均显微硬度值达1303.5HV_0.5,其耐磨性能最佳。     

感应熔覆原位自生TiC/Ni基复合涂层的组织与耐磨性研究

为了提高16Mn钢的干滑动磨损耐磨性能,以Ni60、钛粉和石墨粉为原料对16Mn钢表面进行感应熔敷处理,制备出以TiC颗粒为增强相的原位自生复合涂层,利用金相、SEM、XRD等技术分析了涂层的显微组织,在室温干滑动磨损试验条件下测试了涂层的耐磨性.结果表明:涂层中TiC颗粒均匀分布于共晶基体上,整个涂层组织均匀、无气孔、无裂纹;涂层与基材形成了良好的冶金结合,涂层具有很高的硬度,在室温干滑动磨损试验条件下具有优异的耐磨性能.     

激光熔覆TiCp／Ni基合金复合涂层中TiCp的行为

通过激光熔覆TiCp/Ni基合金复合涂层微观组织的研究表明,TiC颗粒在熔覆过程中表面发生部分溶解,当凝固时,溶解的部分TiC在残留TiC颗粒上重新外延生长析出,并与基体合金元素产生附加合金化,同时,TiC颗粒成为从激光熔体凝固各相优先形核的基底;TiC颗粒与凝固前沿间的相互作用控制其微观分布。     

Effects of La2O3 on microstructure and wear properties of laser clad γ/Cr7C3/TiC composite coatings on TiAl intermatallic alloy

The effects of La₂O₃ addition on the microstructure and wear properties of laser clad γ/Cr₇C₃/TiC composite coatings on γ-TiAl intermetallic alloy substrates with NiCr–Cr₃C₂ precursor mixed powders have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and energy-dispersive spectrometer (EDS) and block-on-ring wear tests. The responding wear mechanisms are discussed in detail. The results are compared with that for composite coating without La₂O₃. The comparison indicates that no evident new crystallographic phases are formed except a rapidly solidified microstructure consisting of the primary hard Cr₇C₃ and TiC carbides and the γ/Cr₇C₃ eutectics distributed in the tough γ nickel solid solution matrix. Good finishing coatings can be achieved under a proper amount of La₂O₃-addition and a suitable laser processing parameters. The additions of rare-earth oxide La₂O₃ can refine and purify the microstructure of coatings, relatively decrease the volume fraction of primary blocky Cr₇C₃ to Cr₇C₃/γ eutectics, reduce the dilution of clad material from base alloy and increase the microhardness of the coatings. When the addition of La₂O₃ is approximately 4 wt.%, the laser clad composite coating possesses the highest hardness and toughness. The composite coating with 4 wt.%La₂O₃ addition can result the best enhancement of wear resistance of about 30%. However, too less or excessive addition amount of La₂O₃ have no better influence on wear resistance of the composite coating.     

Microstructure and wear properties of Fe–TiC surface composite coating by laser cladding

AISI 1045 steel surface was alloyed with pre-placed ferrotitanium and graphite powders by using a 5-kW CO₂ laser. In situ TiC particles reinforced Fe-based surface composite coating was fabricated. The microstructure and wear properties were investigated by means of scanning electron microscopy, transmission electron microscopy, and X-ray diffraction, as well as dry sliding wear test. The results showed that TiC carbides with cubic or flower-like dendritic form were synthesized via in situ reaction between ferrotitanium and graphite in the molten pool during laser cladding process. The TiC carbides were distributed uniformly in the composite coating. The TiC/matrix interface was found to be free from cracks and deleterious phase. The coatings reinforced by TiC particles revealed higher wear resistance than that of the substrate.     

In-situ TiC Reinforced Composite Coating Produced by Powder Feeding Laser Cladding

A Ni-base alloy composite coating reinforced with TiC particles of various shapes and sizes on medium carbon steel substrate was produced by multilayer laser cladding. The chemical compositions, microstructures and surface morphology of the cladded layer were analyzed using energy dispersive X-ray spectroscopy （EDX）, scanning electron microscope （SEM）, and X-ray diffractometry （XRD）. The experimental results showed that an excellent metallurgical bonding between the coating and the substrate was obtained. The microstructure of the coating was mainly composed of γ-Ni dendrites, a small amount of CrB, Ni3B, M23C6 and dispersed TiC particles. Much more and larger TiC particles formed in the overlapping zone, which led to a slightly higher microhardness of this zone. The maximum microhardness of the coating was about HV0.21200. The effects of the laser processing parameters on the microstructures and properties of coating were also investigated.     

硬质相对冷喷涂FeAl金属间化合物涂层性能的影响

FeAl金属间化合物具有优良的物理性能和力学性能,但其室温塑性和断裂韧性低,限制了其工程应用.利用机械合金化制备了Fe(Al)固溶体合金粉末及Al2O3,WC硬质相增强的复合合金粉末,通过冷喷涂沉积涂层并结合后热处理原位反应制备了FeAl金属间化合物涂层及其复合涂层.利用扫描电镜(SEM)、X射线衍射仪(XRD)及显微硬度仪等研究了硬质相对球磨粉末组织结构、冷喷涂FeAl金属间化合物涂层组织结构及性能的影响.结果表明.硬质相可显著加速球磨粉末内部层状结构的细化程度,喷涂态涂层具有不同于传统热喷涂涂层的层状组织结构,热处理可实现喷涂态涂层中Fe(Al)固溶体向FeAl金属间化合物的原位转变,致使层状结构消失,获得无粒子界面的FeAl金属间化合物涂层,弥散分布的硬质相可显著提高冷喷涂FeAl金属间化合物涂层的强化稳定性.     

激光熔敷Ti5Si3/NiTi2复合材料涂层的组织与耐磨性

以Ti-Si-Ni合金粉末为原料，利用激光熔敷技术在BT9钛合金表面制备出了以金属间化合物Ti5Si3为增强相，以NiTi2为基体的Ti5Si3/NiTi2金属间化合物快速凝固耐磨复合材料涂层，Ti5Si3/NiTi2合材料涂层的硬度高，组织均匀，致密，与基材之间为完全冶金结合，在干滑动磨损试验条件下具有很好的耐磨性。     

Ti-C含量对多孔TiC/FeAl复合材料孔型结构和力学性能的影响

以尿素为造孔剂,利用自蔓延高温合成技术制备了多孔TiC/FeAl复合材料,主要考察了Ti-C含量（质量分数为15wt%~35wt%）对多孔TiC/FeAl复合材料孔型结构和压缩性能的影响。当Ti-C含量不高于25wt%时,多孔TiC/FeAl复合材料由毫米孔和孔壁微孔组成规则的复合孔型结构。相互连通的毫米孔产生于尿素颗粒的挥发和液相迁移;微孔尺寸为10~50 μm,产生于Fe-Al-Ti-C粉末的自蔓延过程,孔径随Ti-C含量的增加而增大。通过调整尿素的体积分数,多孔TiC/FeAl复合材料的孔隙率可控制在56.64%~85.35%。当Ti-C含量不高于25wt%时,多孔TiC/FeAl复合材料的抗压强度随Ti-C含量的增加而增大。当Ti-C含量高于25wt%时,多孔TiC/FeAl复合材料壁面微孔形状很不规则,且抗压强度下降。孔隙率约为64.3%时,多孔Fe-Al金属间化合物和TiC/FeAl复合材料（Ti-C含量为25wt%）的抗压强度分别为20.03 MPa和66.68 MPa,对应的应变值分别为4.77%和8.21%。另外,多孔TiC/FeAl复合材料的压缩性能可用Gibson-Ashby模型来解释。     

Y2O3对钛基激光熔覆层组织及性能的影响

针对Ti811钛合金硬度低、耐磨性差的问题,以TC4粉、Ni45A粉和Y₂O₃粉为原料,采用同轴送粉激光熔覆技术在Ti811钛合金表面进行了激光熔覆制备耐磨复合涂层的实验,分析了熔覆层的组织和相组成,测试了熔覆层的显微硬度和摩擦磨损等力学性能。研究表明:复合涂层组织由枝晶TiC、依附生长于枝晶TiC表面的纳米颗粒TiC、生长于基体表面的等轴球形（近球形）TiC、金属间化合物Ti₂Ni、增强相TiB、TiB₂及基体α-Ti组成,所有生成相呈均匀弥散分布状态;涂层中等轴球形（近球形）TiC和Y₂O₃构成了复合相结构,经二维点阵错配度计算表明,Y₂O₃的（111）晶面与TiC的（110）晶面的二维点阵错配度δ=6.54%,因此Y₂O₃可作为TiC的有效异质形核核心细化晶粒;涂层的显微硬度处于HV_0.5 655~700之间,较Ti811基材提高了约1.6~1.8倍;涂层的磨损机制主要为磨粒磨损,摩擦磨损性能较基材显著提升。      

激光熔覆制备原位自生TiC增强Ni3（Si,Ti）复合涂层研究

运用激光熔覆技术修复受损的烟汽轮机叶片,在GH864镍基合金表面制备原位自生TiC颗粒增强Ni3(Si,Ti)金属间化合物复合涂层.利用扫描电镜、能谱分析仪、X射线衍射仪及显微硬度计研究了(Ti+C)的加入量对熔覆层组织及硬度的影响.研究表明:在优化的工艺参数下可获得宏观质量完好,无裂纹、气孔等缺陷,且与基体呈冶金结合的激光熔覆层,熔覆层由Ni(Si)、Ni3(Si,Ti)和TiC组成;当合金粉末中(Ti+C)的加入量为20%时熔覆层的硬度最高可达780Hv,是基体材料的2.4倍.     

Microstructure and micro‐hardness of in situ synthesized TiC particles reinforced Fe‐based alloy composite coating by laser cladding

A Fe‐based composite coating reinforced by in situ synthesized TiC particles was fabricated on Cr12MoV steel by using 6 KW fiber laser cladding. A serial of experiment has been carried out with different laser power, scanning speed, and powder feed rate, from which TiC could be in situ synthesized only in certain realms laser cladding parameters. X‐ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, transmission electron microscope and a hardness tester are used to test the microstructure, micro‐hardness and component distribution. The coating is mainly composed of alpha ;‐Fe, TiC and Fe₃C. TiC particles were commonly precipitated in three kinds of morphologies, such as quadrangle, cluster, and flower‐like shape. The grains were refined, and there were no cracks and few stomas. Defect‐free coating with metallurgical joint to the substrate was obtained. TiC distributed more concentratively in the upper layers than the middle and bottom layers. From the surface of cladding layer 0.8 mm the highest micro‐hardness was up to HV930, obviously higher than that of the substrate.     

碳化钛/钛镍金属间化合物复合涂层相组织研究

利用钛粉、镍粉和胶体石墨,真空条件下通过反应钎涂技术在低碳钢基体上制备了与基体冶金结合的碳化钛/钛镍金属间化合物复合涂层。采用扫描电子显微镜、能谱仪、X射线衍射仪及硬度计,研究了涂层的相组成、组织结构和成分分布。涂层组织由NiTi2、NiTi、TiC和hcp Ti组成,而涂层界面由NiTi和少量的hcp Ti构成,并且TiC主要分布在涂层中层。涂层中的NiTi2、NiTi、TiC是在钎涂过程中原位反应合成的,而且TiC和NiTi的量随碳含量的增加而增加。涂层表面硬度达到85HR15N,但不随TiC和NiTi含量增加而增高。     

激光熔覆原位自生TiC颗粒增强镍基复合涂层的组织与耐磨性

采用预置粉末法在45钢表面进行激光熔覆镍基Ni60A+x%(SiC+Ti)(质量分数,下同)复合粉末涂层的实验研究。使用往复式磨损试验机对不同涂层材料的熔覆层进行干摩擦磨损实验,利用金相显微镜、扫描电镜(SEM)观察和分析熔覆层的显微组织与磨损形貌。结果表明:复合粉末通过原位反应生成弥散分布的TiC颗粒增强复合涂层,随着(SiC+Ti)含量的增加,颗粒状TiC的尺寸和数目逐渐增加;复合粉(SiC+Ti)含量达到60%时,微观组织有气孔和夹杂缺陷;复合粉(SiC+Ti)含量为48%时,熔覆层耐磨性最佳;复合涂层的磨损主要为磨粒磨损,机理为微观切削和挤压剥落。     

TiC与TiC-WC的添加对FeAl/Al2O3复合材料力学性能的影响

在FeAl/Al2O3复合材料基体中分别加入TiC或TiC-WC固溶体可显著提高其抗弯强度。当添加20％TiC和20％TiC-WC固溶体时，复合材料的抗弯强度分别达到1028．46MPa和1328．72MPa，但其断裂韧性分别降低约40％和30％。当TiC-WC固溶体加入量为5％时，可同时提高复合材料的抗弯强度和断裂韧性。     

TA15钛合金表面原位合成TiC增强钛基激光熔覆层的组织与耐磨性EI北大核心CSCD

采用激光熔覆技术在TA15钛合金表面原位合成TiC增强钛基涂层。利用光学显微镜、扫描电镜、X射线衍射仪、能谱分析仪、显微硬度计、摩擦磨损试验机等研究涂层的成形质量、微观组织、物相组成、硬度和摩擦学性能。结果表明:涂层主要由β-Ti,Co_(3)Ti,CrTi_(4)和TiC等物相组成,涂层与基体形成了良好的冶金结合。涂层结合区组织是平面晶和柱状晶,中部组织是树枝晶,顶部组织是等轴晶。涂层各微区的碳化钛形貌有显著差别,其中顶部和中部区域碳化钛为粗大的树枝状和花瓣状,而结合区为针状和近球状。涂层显微硬度最大值为715HV,约是TA15显微硬度(330HV)的2.1倍;同等条件下涂层磨损量为30.14 mg,约为TA15磨损量98.11 mg的30.7%。涂层与基体的磨损机制均为磨粒磨损和黏着磨损的复合磨损模式,但涂层的磨损程度较轻。     

Effect of nano-CeO2 on microstructure properties of TiC/TiN+TiCN-reinforced composite coating

TiC/TiN+TiCN-reinforced composite coatings were fabricated on Ti–6Al–4V alloy by laser cladding, which improved surface performance of the substrate. Nano-CeO₂ was able to suppress crystallization and growth of crystals in the laser-cladded coating to a certain extent. With the addition of proper content of nano-CeO₂, this coating exhibited fine microstructure. In this study, Al₃Ti+TiC/TiN+nano-CeO₂ laser-cladded coatings have been studied by means of X-ray diffraction and scanning electron microscope. X-ray diffraction results indicated that Al₃Ti+TiC/TiN+nano-CeO₂ laser-cladded coating consisted of Ti₃Al, TiC, TiN, Ti₂Al₂₀Ce, TiC_0·3N_0·7, Ce(CN)₃ and CeO₂, this phase constituent was beneficial in increasing microhardness and wear resistance of Ti–6Al–6V alloy.     

Microstructure and properties of in‐situ vanadium carbide phase reinforced nickel based coating by laser cladding

Laser cladding has been applied to fabricate in‐situ vanadium carbide phase on the surface of C45E (according to ISO 683‐1:2016 (E)) using a preplaced powder consisting of 55 wt.% Ni35 and 45 wt.% (FeV50 + graphite), meanwhile, pure Ni35 has also been cladded for comparison. The microstructure and phases analysis were carried out by means of optical microscope, X‐ray diffractometer, scanning electron microscope, energy dispersive spectroscopy, and electron probe microanalysis. The microhardness and wear resistance were tested through the microhardness tester and ring‐on‐block wear tester respectively. The results show that there are many kinds of microstructure such as cellular and columnar crystals for the pure Ni35 cladding coating, and lots of cellular or dendritic vanadium carbide and reticular Cr₂Fe₁₄C₃ phases distribute over the Fe₃Ni₂ matrix in the coating cladded with 55 wt.% Ni35 and 45 wt.% (FeV50 + graphite). Vanadium carbide phase is uniformly distributed and bonded metallurgically to the matrix very well, which increases the hardness and wear resistance. The wear resistance of coating cladded with 55 wt. % Ni35 and 45 wt. % (FeV50 + graphite) alloy powder is 5.16 times as high as C45E, and is higher 139.7% than that of the pure Ni35 clad layer.