共查询到18条相似文献,搜索用时 78 毫秒
1.
2.
3.
采用1[∶]1水模型和工业插钉法研究了吹氩板坯连铸结晶器内钢水流态,并讨论了通钢量、吹氩量、水口浸入深度与水口结构对结晶器流态的影响。水模型结果发现,结晶器内宏观流态主要包括双股流和单股流,钢水通量和吹氩量是影响结晶器内钢水流态的决定性因素。为得到双股流,应采用高通钢量和低吹氩量,缩小断面、增大浸入深度和使用凸底水口有利于双股流形成。基于水模型结果,为维持结晶器内双股流态,在实际浇铸中提出减少连铸过程吹氩量低于临界吹氩量,在宽断面和低拉速下使用凸底水口等措施。工业插钉试验结果与水模型吻合较好,这表明水模型结果可指导现场浇铸实践。 相似文献
4.
采用水力学模型模拟试验,研究了影响结晶器内流场的主要因素和塞棒吹氩对结晶器流场的影响,并且研究了影响浸入式水口内气液二相流态的主要因素和氩气泡在结晶器内的状态,得到了最佳吹气工艺参数。 相似文献
5.
针对宝钢一炼钢厂的结晶器吹氩水口进行了1:1水模实验,研究了不同板坯宽度、拉速、水口出水口面积、出水口角度、浸入深度和吹气量等条件下结晶器液面波动和流股在窄面的冲击点的冲击点的变化情况,并提供了水口优化设计及操作参数,为提高连铸生产率及铸坯质量提供了依据。 相似文献
6.
7.
8.
9.
10.
板坯连铸机结晶器钢液卷渣的水模型研究 总被引:1,自引:0,他引:1
针对安钢超低头板坯连铸机结晶器液面卷渣现象 ,用 0 6∶1 0水模型 ,研究了水口浸入深度 30mm、6 0mm和 110mm时 ,铸坯拉速 1 0~ 0 7m min、水流量 2 6 2 4~ 18 4m3 min范围内水口浸入深度、拉速对结晶器内钢液卷渣程度的影响。提出卷渣指数J =V·h (t·H) ,式中V 拉速 ;h 1 10大波值 ;t 开始卷渣时间 ;H 水口浸入深度。结果得出 ,为防止安钢板坯结晶器液面卷渣 ,当水口浸入深度为 110mm时 ,拉速应≤0 90m min ;浸入深度 6 0mm时 ,拉速应≤ 0 85m min ;J应 <1 37× 10 - 2 mm s2 。 相似文献
11.
E. V. Shtepan G. A. Red’ko V. E. Ukhin A. V. Naumenko E. Yu. Zhiboedov 《Russian Metallurgy (Metally)》2007,(8):672-675
The effect of argon blowing into a steel stream on the stability of continuous casting is studied. Physical modeling and mathematical simulation are performed to find the parameters of argon blowing into a steel stream during the casting of a section billet. 相似文献
12.
E. V. Shtepan G. A. Redko V. E. Ukhin A. V. Naumenko E. Yu. Zhiboedov 《Russian Metallurgy (Metally)》2008,2007(8):672-675
The effect of argon blowing into a steel stream on the stability of continuous casting is studied. Physical modeling and mathematical
simulation are performed to find the parameters of argon blowing into a steel stream during the casting of a section billet.
Original Russian Text ? E.V. Shtepan, G.A. Red’ko, V.E. Ukhin, A.V. Naumenko, E.Yu. Zhiboedov, 2007, published in Elektrometallurgiya,
2007, No. 6, pp. 20–23. 相似文献
13.
The work studies the extent of asymmetric flow in water models of continuous casting molds of two different configurations. In the molds where fluid is discharged through multiple holes at the bottom, the flow pattern in the lower portion depends on the size of the lower two recirculating domains. If they reach the mold bottom, the flow pattern in the lower portion is symmetrical about the central plane; otherwise, it is asymmetrical. On the other hand, in the molds where the fluid is discharged through the entire mold cross section, the flow pattern is always asymmetrical if the aspect ratio is 1:6.25 or more. The fluid jet swirls while emerging through the nozzle. The interaction of the swirling jets with the wide sidewalls of the mold gives rise to asymmetrical flow inside the mold. In the molds with lower aspect ratios, where the jets do not touch the wide side walls, the flow pattern is symmetrical about the central plane. 相似文献
14.
15.
介绍了模拟结晶器内渣膜形成的实验方法, 综述了国内外学者在保护渣传热方面所做的研究工作, 包括固态渣膜的界面热阻、保护渣的导热系数、辐射传热以及渣膜的光学性质, 并提出了今后在渣膜形成及传热研究中有待进一步完善的内容和方向.现有的研究结果表明利用热丝法可以对渣膜的形成过程进行原位观察, 采用水冷铜探头法可以获取用于研究渣膜微观组织的固态渣膜样品.渣膜的界面热阻在0.0002~0.002 m2·K·W-1之间.在800℃以下, 保护渣的导热系数在1.0~2.0 W·m-1·K-1范围内, 且随温度的升高而逐渐增加.渣膜中的晶体一方面可以增加渣膜的界面热阻, 另一方面可以提高固态渣膜的反射率, 起到降低辐射热流的作用.此外, 过渡族金属氧化物的加入以及固态渣膜中弥散分布的微小颗粒也能改变渣膜的光学性质, 从而影响通过渣膜的辐射传热. 相似文献
16.
Numerical investigation of the interface in a continuous steel casting mold water model 总被引:2,自引:0,他引:2
In this study, the steady-state Navier-Stokes equations are solved on a curvilinear nonorthogonal grid, following the finite
volume approximation, with a pressure prediction-correction method, for the case of a flow in a model steel casting mold.
The steel flow is simulated by water flow and the slag layer by an oil film, following conditions of previous experimental
studies. The simulation aims at the understanding of the free wave and the interface surface wave behavior and the mechanism
that leads to the breakup of the steel-slag interface, and thus induction of impurities inside the final steel product. Boundary
conditions are set on the free and the interface surfaces, and an adaptive grid mechanism is used in order to update the grid’s
shape so as to follow the wave formation. Several cases have been considered with the inlet velocity parameter, and results
concerning the velocity field and the generated waves are reported. It is shown that a critical casting speed exists that
leads to wave instability, which may be associated with emulsification phenomena. 相似文献
17.
国内某厂镀锡板缺陷处夹杂物主要来自结晶器保护渣的卷入,但其成分与结晶器保护渣有明显差别。为了进一步研究这种成分差别的原因,建立了耦合热力学平衡和动力学扩散的结晶器卷渣类夹杂物的成分转变动力学模型,明确了卷渣类夹杂物的尺寸和密度对其成分转变的影响规律,并通过对结晶器和液相穴内的钢液流动和夹杂物运动的数值模拟研究了夹杂物在钢液中的停留时间。结果表明:结晶器保护渣卷入钢液后与钢液不断发生反应,成分会发生明显改变。卷渣类夹杂物转变为缺陷处夹杂物所需要的时间与夹杂物尺寸以及夹杂物密度有关,夹杂物的尺寸和密度越大,转变为缺陷处夹杂物成分所需的时间越长。卷渣类夹杂物转变为缺陷处夹杂物所需时间与夹杂物尺寸呈幂函数关系,与夹杂物密度呈二次函数关系。夹杂物在钢液中的平均停留时间随夹杂物直径的增大而减小,并且随着拉速的增大而减小。小尺寸夹杂物一旦被卷入钢液中,将有充足的时间转变为缺陷处的成分。大尺寸夹杂物在钢液中的平均停留时间小于成分转变时间,但最大停留时间远大于成分转变所需时间,表明部分大尺寸夹杂物依然具有充足的停留时间转变为缺陷处的成分。 相似文献
18.
时频分析是一种研究波动信号特征、揭示波动现象内在机理的有效方法。将时频分析方法应用于吹氩连铸结晶器内的液面波动特性研究,采用水模型试验获取液面波动数据进行时频分析,研究吹氩量、拉速、水口浸入深度和结晶器宽度等工艺参数对液面波动行为的影响,探究液面波动的内在机理。结果表明,振幅较高的频率集中在0~2.5 Hz,其中振幅最大的主频率位于0.1 Hz附近,此外1.5 Hz和2.5 Hz处也存在较高的峰值;通过时域分析发现,增大吹氩量和拉速、或减小水口浸入深度和结晶器宽度将加剧液面波动;通过频域分析发现,拉速、水口浸入深度、结晶器宽度与液面波动主频率有较强的关联性,说明三者均与液面波动的主要振动源高度相关。 相似文献