Convective Regime of Filtration Combustion of Energetic Materials in a Cocurrent Flow of Their Combustion Products

The convective regime of filtration combustion of energetic materials in a cocurrent flow of their combustion products is studied using a model with extremely simplified kinetics and heat transfer, which shows instability of the process. It is shown that the more accurate twotemperature model describes a steadystate regime. In this regime, the gas temperature on the hot boundary of the heating zone is well below the combustion temperature, and the solidphase temperature is well below the temperature proposed in recent studies on this topic. It is pointed out that the twotemperature approach is unjustified and intragranular nonisothermicity must be taken into account for convective regimes. It is shown that the threetemperature model, which takes into account this effect, does not give a stable steadystate solution.     

Mechanism of Upper Temperature Limits in a Wave of Filtration Combustion of Gases

A physical mechanism is established, responsible for the experimentally observed strong deceleration of the growth rate of the maximum skeleton temperature in a wave of filtration combustion of gases with increasing flow rate. The maximum temperatures of the gas and skeleton become commensurable, and the length of the thermalrelaxation zone becomes much shorter. A classification of regimes based on the temperatureheterogeneity criterion ₁ is proposed. Explicit analytical solutions are obtained for the wave for ₁1 and ₁1. A correction to reverse reactions in combustion products is considered. The effect of composition on wave behavior is studied by means of numerical calculations with a detailed kinetic scheme. The activation energy for ultrarich and ultralean methane–air mixtures is evaluated. It is concluded that the limiting efficiency of the heatrecuperation cycle in the wave is reached as ₁1; methods for maximizing the efficiency are suggested.     

Effect of framework aluminum in proton‐ or copper‐exchanged MFI ferrialuminosilicates on their activity for the reduction of nitric oxide with ammonia

Reduction of NO with ammonia in excess oxygen has been carried out on protonform and Cu²⁺exchanged MFI ferrialuminosilicate. Though HZSM5 showed very low activity, the framework Al in Hferrialuminosilicate greatly enhanced the activity. The framework Al in Cu²⁺exchanged ferrialuminosilicate also enhanced the activity to some extent.     

Structure of the Reaction Zone of a Steady Detonation Wave in Dinitrodiazapentane

The massvelocity profiles in 2,4dinitro2,4diazapentane samples of different densities were registered by a laser interferometer and the electromagnetic technique. The reaction time was shown to reach 300 nsec and weakly depend on density, while the pressure in the chemical spike can be twice as high as that at the Chapman–Jouguet point. No special features due to diamond formation were observed in the massvelocity profiles registered in the chemical reaction zone.     

Formation and reactions of isocyanic acid during the catalytic reduction of nitrogen oxides

Reactions which can produce and consume isocyanic acid (HNCO) over two types of catalysts active for the reduction of nitrogen oxides have been investigated. More than 1000 ppm HNCO can be produced by the reduction of 3000 ppm NO with H₂/CO mixtures over a Pt/SiO₂ catalyst. Complete hydrolysis of HNCO to ammonia and carbon dioxide occurs if even weakly catalytic materials, such as CeO₂/SiO₂ and BaO/SiO₂, are placed downstream. Isocyanic acid is also involved as an intermediate in the reaction of nitromethane over CoZSM5 and CuZSM5 under the conditions of hydrocarbon SCR. In the initial stages of reaction there is complete conversion through to N₂ with CuZSM5 but the process stops at ammonia with CoZSM5 at temperatures below 350°C. In both cases, but especially with CoZSM5, isocyanic acid becomes observable as the catalyst deactivates during continuous exposure at temperatures below about 290°C. In situ FTIR measurements indicate that deactivation is due to a reaction between isocyanic acid and ammonia which generates cyclic striazine compounds.     

Impact of Structural Factors on Unsteady Combustion Modes of Gasless Systems

Based on the twotemperature, twovelocity timedependent model of gasless combustion, taking into account structural transformations related to the force action of the gas filtering in the pores and vitrification and volume variation of the condensed phase during the chemical transformation, selfoscillatory combustion modes are studied. Structural transformations are shown to have a pronounced effect on the propagation pattern of combustion waves and can either stabilize or destabilize combustion. The major structural parameters appreciably affecting combustionwave stability are the initial porosity, particle size, and pressure.     

Vapor‐phase synthesis of acetophenone in benzene acylation over CeHZSM‐5(30) zeolite

The benzene acylation was carried out with acetic anhydride as an acylating agent in vapor phase over HZSM5, Si/Al =30 and 280, HY and Ce, Vmodified HZSM5(30) zeolite catalysts at atmospheric pressure. The yield of acylated product acetophenone was found to be 82.1 wt% with 95.0% selectivity at 86.4 wt% conversion of acetic anhydride over Cemodified HZSM5(30) where Brønsted acidic sites are active for this reaction.     

Dehydration of 2‐methylbutanal to isoprene using aluminium phosphate catalysts

The synthesis of isoprene from the dehydration of 2methylbutanal is described using aluminium phosphates as catalysts. Two samples of aluminium phosphate are studied prepared from the reaction of phosphoric acid with aluminium chloride or sulphate. The chloride route gives a mixed cristobalite/tridymite AlPO₄ and this is shown to be more active than a catalyst containing only the tridymite form of AlPO₄ formed from the sulphate route. The AlPO₄ catalysts are also shown to be active catalysts for the synthesis of isoprene from 3methylbutan2one, which is the major byproduct formed from the reaction of 2methylbutanal. The AlPO₄ catalysts are deactivated due to the deposition of coke in addition to loss of phosphorus from the surface. Catalytic activity can be totally restored by a simple calcination procedure at 800°C.     

Chemistry of Combustion Waves in Substances with a Complicated Structure of Reagent Molecules. 1. Structure of the Front of Rich Isopentane Flame

Results on the structure of the lowtemperature relaxation zone of the front of a laminar Bunsen flame of isoC₅H₁₂ (2methylbutane) under atmospheric pressure are presented. The flame of a premixed mixture isoC₅H₁₂ + O₂ + Ar with a fueltoair equivalence ratio of 1.7 is examined. The mass fluxes, total rates of reactions of matter consumption and expenditure, balance of substances, and profiles of bulk heatrelease rates are calculated on the basis of the experimental concentration and temperature profiles. The results obtained indicate that there is a vast region of lowtemperature conversion of isopentane in the flame front. It is found that only part of the products sampled by the microprobe from different points of the flame front results from transformations in the lowtemperature region, namely, oxygen, isopentane, water, carbon monoxide, propane, methane, and methanol. Ethylene, propylene, hydrogen dioxide, and formaldehyde are present in the lowtemperature zone in insignificant amounts; they are secondary products of conversion of methyl and propyl radicals. It is assumed that the observed feature is a result of the competing interaction of two mechanisms of fuelmixture conversion: selfcatalysis and thermal selfacceleration. Based on the previously suggested mechanism of oxidation pyrolysis by the scheme of intramolecular quadratic destruction, experimentally observed fragmentation of the isopentane molecule is demonstrated. In contrast to npentane, formation of methyl alcohol has been found in isopentane convection products.     

Gasless Combustion of Ti–Al Bimetallic Multilayer Nanofoils

Ti–Al multilayer foils were produced magnetron vacuum deposition. The microstructure period varied in the range of 5–110 nm, the number of layers was 150–4700, and the total thickness of a multilayer foil reached 15–20 m. The gasless combustion of the foils was studied. Steadystate and pulsating combustion regimes were revealed; combustion temperatures were determined for both regimes. It was shown that the most probable mechanism of the selfpropagating reaction is the diffusion of Al in Ti at a temperature close to the temperature of the transition.     

A study of the acidic and catalytic properties of pure and sulfated zirconia–titania and zirconia–silica mixed oxides

Protonated pyridine (PyH⁺) was not found on ZrO₂ (Z) or ZrO₂–TiO₂ (ZT), but was detected on sulfated oxides (ZS, ZTS) by IR spectroscopy. In contrast, ZrO₂–SiO₂ samples containing about 30–80 mol% ZrO₂ showed Brønsted acidity both in nonsulfated (ZS) and sulfated (ZSS) forms. The total acidity was determined by NH₃TPD. Introduction of sulfate ions increased the sitespecific catalytic activity (TOF) in the conversion of cyclopropane or nhexane. The effect of sulfate ions was more significant on samples rich in zirconia. Results suggest that Zr is homogeneously distributed in ZS samples rich in silica. Zirconiabound dimeric sulfate, generating strong acidity, could not be formed in these preparations due to the absence of fairly large ZrO₂ domains.     

Shock‐Induced Polarization of Materials

A new computational method of calculating signals of shockinduced electric polarization of materials is proposed and used to analyze previous experimental results on the shockinduced electric polarization of Plexiglas. Experimental results on the shockinduced electric polarization of granite are presented.     

Synthesis of nanosized platinum cluster in cubic mesoporous material via a direct introduction method

Platinumclustercontaining cubic mesoporous material (PtMCM48) has been synthesized by direct introduction of chloroplatinic acid during the synthesis of MCM48. In addition, we have also studied the incipient wetness impregnation and ionexchange method to obtain the platinumcontaining cubic mesoporous material. The nature of the platinumMCM48 catalyst has been characterized by different techniques such as XRD, N₂ adsorption, TEM, XPS, and NMR. The catalyst obtained by direct introduction of platinum in the synthesis gel shows higher activity in the hydrogenation of benzene and toluene.     

Fabrication and characterization of the Ag‐based high‐technology model nanocluster catalyst for ethylene epoxidation manufactured by electron beam lithography

Nanocluster catalysis is an area where greater fundamental knowledge is needed to understand the behavior of aggregates of metal atoms in determining product selectivity of chemical reactions. While catalysis is practiced industrially with economic success there is still a great need to eliminate wasteful sidereactions which hurt overall yields. Here we report on fabrication of a Agbased hightechnology model nanocluster catalyst by using electron beam lithography (EBL) designed for systematic studies of the ethylene epoxidation reaction. The catalyst is made of a square array of cylindershaped Ag nanoclusters that are 200 Å in diameter, deposited on a four inch silicon wafer, precovered with a 100 Å thick film of alumina. The height of the particles and interparticle distance can vary, and were chosen to be 150–300 and 1000 Å, respectively. The high technology catalyst was characterized by Xray photoelectron spectroscopy (XPS), highresolution transmission electron microscopy (TEM), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The thermal stability of Ag nanoclusters in vacuo was investigated.     

Some Features of Gas‐Flame Propagation in Narrow Tubes

The dependence of the flamefront curvature on the composition of the mixture in tubes of various diameters is considered. The combustionwave velocities are measured for different fractions of fuel in the mixture. It is shown that the dependence of the burning velocity on the composition of the mixture has two maximums, one of them being related to the transition of the laminar combustion mode to turbulent combustion. Combustion turbulization is caused by flame instability to acoustic oscillations. Variations of the combustionwave shape due to acoustic oscillations are observed.     

Ammonia synthesis over multi‐promoted iron catalysts obtained by high‐energy ball‐milling

The feasibility of producing ammonia synthesis catalysts from highenergy ballmilling of a simple mixture of the constituent oxides has been investigated. The effect of ballmilling the fused oxidic precursor of the industrial KM1 ammonia synthesis catalyst has also been studied. The results show that highenergy ballmilling offers some interesting possibilities for preparing novel catalytic materials. It is observed that ballmilling of the powder oxides mixture leads to formation of solid solutions and the catalytic activity is significantly higher than that of the starting material. Furthermore, ballmilling of fused oxidic KM1 precursor is seen to give rise to more homogeneous promoter distribution and slightly higher activity. The quite small activity increase observed in this case probably reflects the fact that the fusion process has already resulted in a close to optimal promoter distribution. The choice of atmosphere during ballmilling is also seen to offer possibilities for regulating the phase composition.     

Shock‐Wave Deformation and Fracture of Zirconium Dioxide Ceramics of Various Fractional Composition and Porosity

The paper reports results from measurements of freesurface velocity profiles of shockloaded zirconium dioxide ceramics with a porosity of 16–22% produced from compositions with a size of the coarse fraction of 0.5–2.0 mm. Shockwave loading of ZrO₂ samples 5–20 mm thick was performed by aluminum impactors 3–12 mm thick with a velocity of 10–100 m/sec. The measured freesurface velocity profiles were used to assess the dynamic compressive and tensile strengths of the ceramics and thedamping properties of the ceramics.     

Quasi‐Homogeneous and Pseudospin Modes of Zirconium‐Wire Combustion in Air

A novel experimental technique is proposed for examining the transition mechanism from quasihomogeneous to heterogeneous combustion — burning of a variablepitch spring. Depending on the pitch of aircombustible zirconium springs, two combustion modes are possible. Quasihomogeneous (layerbylayer) combustion is observed in the case of smallpitch springs; as the spring pitch increases, quasihomogeneous combustion transforms into heterogeneous (pseudospin) combustion. Conditions for the occurrence of various combustion modes, depending on the spring diameter and pitch, are studied.     

Localization of Deformation in Copper Single Crystals During Explosive Collapse

It is established that highrate axisymmetric loading of single crystals by the method of explosive collapse of a hollow thickwalled cylinder causes deformation that involves all active closepacked slip systems. The spatial distribution of macroscopic sites of strain localization is determined by the crystallography of the active systems in singlecrystalline samples. The established correlation between the observed shear bands in the microstructure of copper single crystals and {111} active slip <110> systems of facecentered cubic (FCC) crystals and their symmetric arrangement show that deformation at a rate of 5 · 10⁴ sec^-1 occurs according to the crystalline structure of the materials.