PEM燃料电池中质子交换膜内水和质子的迁移特性

质子交换膜的水含量及水和质子的迁移对PEM燃料电池的性能具有重要影响.提出了一个稳态两相流数学模型,用以研究质子交换膜中的水迁移和水含量及其与质子传递阻力的关系.模型耦合了连续方程、动量守恒方程、物料守恒方程和水在质子交换膜中的传递方程.通过与实验数据对比,验证了模型的有效性.分析模拟结果发现,当电流密度相同时,沿气体流动方向,质子交换膜中水的电渗拉力系数、反扩散系数和水力渗透系数逐步增大,而水的净迁移系数逐步减小;同时,质子交换膜的含水量增加,质子传递阻力逐步下降;增大电池的操作压力,电渗拉力系数、反扩散系数、水力渗透系数、水净迁移系数和质子膜的含水量增加,而质子传递阻力下降,使燃料电池的性能得到了提高.     

低流速燃料电池重力辅助排水

实验研究了反应气体低流速下质子交换膜燃料电池内液滴自身重力对电池性能的影响。结果显示,自身重力有利于液滴脱离气体扩散层,使液态水有效排出电池堆。电池水平放置阴极向下时,液滴重力与其脱离气体扩散层方向一致,电池性能最佳;电池竖直放置时,液滴重力与气体将其吹扫出电池方向一致,其向外排水能力最强。反应气体流速较低时,电池在不同放置方式下,提高其温度,电池性能上升;电池竖直放置时,气体加湿对电池性能影响不大。电池测试时,应该避免电池阴极水平向上。     

低流速燃料电池重力辅助排水

实验研究了反应气体低流速下质子交换膜燃料电池内液滴自身重力对电池性能的影响。结果显示,自身重力有利于液滴脱离气体扩散层,使液态水有效排出电池堆。电池水平放置阴极向下时,液滴重力与其脱离气体扩散层方向一致,电池性能最佳;电池竖直放置时,液滴重力与气体将其吹扫出电池方向一致,其向外排水能力最强。反应气体流速较低时,电池在不同放置方式下,提高其温度,电池性能上升;电池竖直放置时,气体加湿对电池性能影响不大。电池测试时,应该避免电池阴极水平向上。     

阴、阳极加湿程度对PEMFC内部传质的影响

为了研究常规流场下阴、阳极增湿程度对电池内部水分布、传递、膜性能及水拖曳系数等的影响,对PEMFC进行二维建模,应用控制容积法对控制方程进行离散,然后求解,得到了电池内部水和反应气浓度、速度分布、膜中电流密度、电势分布及膜中水分布,考察了气体不同增湿程度对质子交换膜电导率及电池内部传质的影响.结果表明,PEMFC中水综合拖曳系数随着阳极加湿程度的增加而增大,随阴极增湿程度的增加而减小,但阳极增湿对水综合拖曳系数的影响比同增湿程度下阴极增湿对水综合拖曳系数的影响大得多.同时,随着阳极加湿程度的升高,质子交换膜（PEM）电导率急剧升高,而阴极加湿程度对PEM电导率的影响只是停留在较小的电流范围之内.故PEMFC在小电流密度工作时,应该使阳极气体充分增湿;而在大电流密度工作时,应该适当降低阳极的增湿程度以降低阴极两相流的机会,从而改善阴极的传质状况.     

PEMFC带沟槽气体扩散层内传输特性孔隙网络模拟

采用三维孔隙网络模型计算了不同沟槽参数下气体扩散层(GDL)的液态水突破压力、毛细压力分布、气体扩散率和液相相对渗透率随饱和度变化,并从孔隙尺度角度探究了沟槽的作用机制。研究结果表明：沟槽改变了GDL的毛细压力分布,提供了液态水直接传输路径并优化了GDL内氧气和液态水的分布,从而提高了氧气有效扩散率。沟槽位置对氧气传输有明显影响,对液相传输的影响取决于是否形成贯穿GDL的传输路径;沟槽加深,氧气和液态水传输性能增强,沟槽穿透GDL时传输性能达到最佳;沟槽变宽,液相传输性能增强,氧气传输性能在低饱和度范围内先增强后减弱。综合各因素,给出了氧气和液态水传输性能最优时的沟槽参数。     

质子交换膜燃料电池膜电极制备方法的研究进展

燃料电池技术作为一种绿色能源技术,在减少能源消耗、环境污染等方面具有巨大潜力。膜电极（MEA）是质子交换膜燃料电池（PEMFC）的核心部件,MEA中电化学反应的顺利进行需要各功能层的协调配合,MEA各功能层涉及的传质、导电、导质子、催化等方面均影响燃料电池的性能。根据制备方法,可以将MEA分为催化剂涂敷基底（CCS）型MEA、催化剂涂敷膜（CCM）型MEA、有序化MEA和一体化MEA。MEA的性能不仅由催化剂本身载量决定,也受其结构设计和制备工艺的影响。本文介绍了MEA制备过程中常见的改进方法,分别从催化剂喷涂、刮涂、模槽挤出涂覆方式,催化剂浆料组成中Nafion含量和溶剂极性选择,催化层梯度化、图案化及界面结构改进,PEM结构增强、图案化、成膜方式等方面的研究进展进行讨论。但是目前对于MEA各功能层界面间的研究较少,应该注意的是催化层/质子交换膜（PEM）界面以及催化层/气体扩散层（GDL）界面设计也将直接影响MEA的性能。     

直接硼氢化钠燃料电池在不同运行条件下的放电特性研究

研究了以Ni粉为阳极催化剂、Pt/C为阴极催化剂、Nafion117为电解质膜的直接硼氢化钠燃料电池(DSBFC),通过电池的极化曲线、功率密度曲线,研究了DSBFC在不同阴极供料方式、不同温度和硼氢化钠浓度等条件下的放电特性.结果表明:阴极通加湿氧气有利于提高电池性能;随着硼氢化钠浓度的增加和温度的升高,电池性能都会提高;50℃时NaBH4浓度对电池性能影响更大,NaBH4浓度为0.5 mol·L-1时温度对电池的性能影响更大.通过电流-时间曲线考察了电池的库仑效率及短期运行的稳定性.结果显示:在高温时电池放电相对平稳;NaBH4浓度越大,库仑效率越低;温度对库仑效率影响不大.以加湿氧气为氧化剂、硼氢化钠浓度为1.0 mol·L-1、电池运行温度为80℃时,DSBFC性能最佳,最大功率密度为39.5 mW·cm-2(0.5 V).     

质子交换膜燃料电池二维全电池两相流综合数值模型

针对直通道质子交换膜燃料电池（PEMFC）建立了一个二维全电池综合数值模型,模型综合考虑参与电化学反应的三个要素反应物质、电子和质子的传输过程以及液态水的淹没和膜内水传输现象。研究了供气压力、液态水淹没对电池性能的影响;比较了不同输出电压、供气湿度等条件对阴极液态水饱和度分布以及电解质膜含水率的影响;预测了基准供气状态下电池的极化曲线和文献报道的实验结果吻合很好。计算结果显示：输出电压越小液态水淹没电极现象越严重;阴极液态水的生成有利于膜的浸润保持较高电导率,但是会淹没电极使有效电极面积减小,导致电池性能下降。     

质子交换膜燃料电池两维、两相流动模型

提出了考虑电池内部两相流动的质子交换膜燃料电池数学模型,模拟了阳极、阴极两侧的流道和扩散层中同时发生两相流动时电池内部的各种传递特性,并用实验数据验证了该模型的准确性。模拟结果显示,当电池阴极扩散层中有液态水存在时会大大降低膜中的局部电流密度;质子交换膜中水的净通量方向可正、可负,因此电池的增湿策略应根据不同的运行工况而不断变化。     

球形团聚物模型在质子交换膜燃料电池过程模拟中的应用

在建立直通道质子交换膜燃料电池(PEMFC)的二维全电池数学模型中,将球形团聚物模型应用至两极的催化剂层。通过调节团聚物中质子传导介质的比例和催化层孔隙率,预测了基准供气状态下单电池的极化曲线,与文献报道的实验数据吻合良好。研究了电池运行过程中,膜电极内各化学组分和电流密度的分布情况及流向,比较了不同供气压力、催化剂铂颗粒尺寸等参数对电池性能的影响。计算结果表明,在阴极及时排出反应产生的水,并在阳极对燃料气进行加湿是保证单电池正常运行的前提,提高阴极的氧化剂气体压力,可显著改善PEMFC单电池性能,特别是在受浓差极化影响较大的大电流密度区;在催化剂铂载量相同的情况下,减小铂颗粒的尺寸可以提高电池的性能。     

采用不同流场的质子交换膜燃料电池内部传递现象模拟

A numerical model for proton exchange membrane (PEM) fuel cell is developed, which can simulate such basic transport phenomena as gas-liquid two-phase flow in a working fuel cell. Boundary conditions for both the conventional and the interdigitated modes of flow are presented on a three-dimensional basis. Numerical techniques for this model are discussed in detail. Validation shows good agreement between simulating results and experimental data. Furthermore, internal transport phenomena are discussed and compared for PEM fuel cells with conventional and interdigitated flows. It is found that the dead-ended structure of an interdigitated flow does increase the oxygen mass fraction and decrease the liquid water saturation in the gas diffusion layer as compared to the conventional mode of flow. However, the cathode humidification is important for an interdigitated flow to acquire better performance than a conventional flow fuel cell.     

PEM fuel cells operated at 0% relative humidity in the temperature range of 23-120 °C

Operation of a proton exchange membrane (PEM) fuel cell without external humidification (or 0% relative humidity, abbreviated as 0% RH) of the reactant gases is highly desirable, because it can eliminate the gas humidification system and thus decrease the complexity of the PEM fuel cell system and increase the system volume power density (W/l) and weight power density (W/kg). In this investigation, a PEM fuel cell was operated in the temperature range of 23-120 °C, in particular in a high temperature PEM fuel cell operation range of 80-120 °C, with dry reactant gases, and the cell performance was examined according to varying operation parameters. An ac impedance method was used to compare the performance at 0% RH with that at 100% RH; the results suggested that the limited proton transfer process to the Pt catalysts, mainly in the inonomer within the membrane electrode assembly (MEA) could be responsible for the performance drop. It was demonstrated that operating a fuel cell using a commercially available membrane (Nafion^® 112) is feasible under certain conditions without external humidification. However, the cell performance at 0% RH decreased with increasing operation temperature and reactant gas flow rate and decreasing operation pressure.     

On the modeling of water transport in polymer electrolyte membrane fuel cells

Water management is a critical issue in polymer electrolyte membrane (PEM) fuel cells, and water transport through the membrane, catalyst layer and gas diffusion layer has significant impact on the cell performance and durability. In this study, the mechanism of water transport processes in PEM fuel cells has been analyzed through 3-D unsteady non-isothermal simulations, along with a comprehensive examination of various modeling approaches in literature. It is shown that the finite rates of sorption/desorption of water in membrane affect the cell current output and the cell response time. Water dissolved in the membrane should be taken as the proper mechanism of water formation in the cathode of practical PEM fuel cells. Capillary pressure and relative permeability have significant impact on the distribution of liquid water saturation and transport, implying a need for their determination under specific PEM fuel cell conditions.     

Non-isothermal effects of single or double serpentine proton exchange membrane fuel cells

Mathematical models on transport processes and reactions in proton exchange membrane (PEM) fuel cell generally assume an isothermal cell behavior for sake of simplicity. This work aims at exploring how a non-isothermal cell body affects the performance of PEM fuel cells with single and double serpentine cathode flow fields, considering the effects of flow channel cross-sectional areas. Low thermal conductivities of porous layers in the cell and low heat transfer coefficients at the surface of current collectors, as commonly adopted in cell design, increase the cell temperature. High cell temperature evaporates fast the liquid water, hence reducing the cathode flooding; however, the yielded low membrane water content reduces proton transport rate, thereby increasing ohmic resistance of membrane. An optimal cell temperature is presented to maximize the cell performance.     

质子交换膜燃料电池水传递模型

提出了用于研究质子交换膜燃料电池膜中水分布、水传递量分布、电流密度分布等的二维数学模型;系统地考察了电池温度、阴阳极压力差、增湿程度、质子膜厚度等条件对水的传递和膜中水分布的影响.计算结果表明:①阳极增湿能够提高气体进口段膜阳极侧水的含量;②使用越薄的质子膜,越能提高膜中水的含量;③阳极增湿程度越大,由阳极向阴极迁移的水量越多.     

Mathematical Model of Proton Exchange Membrane Fuel Cell with Consideration of Water Management

One‐dimensional model on the membrane electrode assembly (MEA) of proton exchange membrane fuel cell is proposed, where the membrane hydration/dehydration and the possible water flooding of the respective cathode and anode gas diffusion layers are considered. A novel approach of phase‐equilibrium approximation is proposed to trace the water front and the detailed saturation profile once water emerges in either anode or cathode gas diffusion layer. The approach is validated by a semi‐analytical method published earlier. The novel approach is applicable to the polarization regime from open circuit voltage to the limiting current density under practical operation conditions. Oxygen diffusion is limited by water accumulation in the cathode gas diffusion layer as current increases, caused by excessive water generation at the cathode catalyst layer and the electro‐osmotic drag across the membrane. The existence of liquid water in the anode gas diffusion layer is predicted at low current densities if high degrees of humidification in both anode and cathode feeds are employed. The influences of inlet relative humidity, imposed pressure drop, and cell temperature are correlated well with the cell performance. In addition, the overpotentials attributed from individual components of the MEA are delineated against the cell current densities.     

Three-dimensional CFD modelling of PEM fuel cells: An investigation into the effects of water flooding

In this work, a three-dimensional PEM fuel cell model has been developed and is used to investigate the effects of water flooding on cell performance parameters. The presence of liquid water in the cathode gas diffusion layer (GDL) limits the flow of reactants to the cathode catalyst layer, thereby reducing the overall reaction rate and curtailing the maximum power that can be derived from the cell. To characterize the effects of water flooding on gas diffusion, effective diffusivity models that account for the tortuosity and relative water saturation of the porous fuel cell electrodes have been derived from percolation theory and coupled with the CFD model within a single phase flow skeleton. The governing equations of the overall three-dimensional PEM fuel cell model, which are a representative of the coupled CFD and percolation theory based effective diffusivity models, are then solved using the finite volume method. Parametric studies have been conducted to characterize the effects of GDL permeability, inlet humidity and diffusivity of the reactants on the various cell performance parameters such as concentration of reactants/products and cell current densities. It is determined that the GDL permeability has little or no effect on the current densities due to the diffusion dominated nature of the gas flow. However, through the incorporation of percolation theory based effective diffusivity model; a marked reduction in the cell performance is observed which closely resembles published experimental observations. This is a reasonable approximation for effects of water flooding which has been inherently used for further parametric studies.