Effects of shot peening on microstructure,thermal performance,and failure mechanism of thermal barrier coatings

Shot peening might be a potential technology to optimize the interface microstructure, plays a critical role on failure behaviors, of thermal barrier coatings (TBCs). It remains a significant challenge to understand the influence of shot peening on microstructure, oxidation resistance, and thermal shock life. In this work, the Y₂O₃-stabilized ZrO₂ TBCs have been deposited by EB-PVD. The phase, microstructure, thermal performance, and failure mechanism of TBCs have been systemically investigated after shot peening. The shot peening process can improve the planeness of interface and reduce the formation of the cauliflower-liked microstructure in TBCs. After shot peening, the TBC coatings exhibit relatively good isothermal oxidation resistance and high thermal shock life due to the optimization of TGO growth and the thermal stability. The phase transformation, TGO growth, and cracks extension might give rise to the failure of TBCs. This work might guide the investigation of the improvement of interface microstructure and failure behaviors.     

Study on thermal shock resistance of Sc2O3 and Y2O3 co-stabilized ZrO2 thermal barrier coatings

In order to reveal the effect of Sc₂O₃ and Y₂O₃ co-doping system on the thermal shock resistance of ZrO₂ thermal barrier coatings, Y₂O₃ stabilized ZrO₂ thermal barrier coatings (YSZ TBCs) and Sc₂O₃–Y₂O₃ co-stabilized ZrO₂ thermal barrier coatings (ScYSZ TBCs) were prepared by atmospheric plasma spraying technology. The surface and cross-section micromorphologies of YSZ ceramic coating and ScYSZ ceramic coatings were compared, and their phase composition before and after heat treatment at 1200 °C was analyzed. Whereupon, the thermal shock experiment of the two TBCs at 1100 °C was carried out. The results show that the micromorphologies of YSZ ceramic coating and ScYSZ ceramic coating were not much different, but the porosity of the latter was slightly higher. Before heat treatment, the phase composition of both YSZ ceramic coating and ScYSZ ceramic coating was a single T′ phase. After heat treatment, the phase composition of YSZ ceramic coating was a mixture of M phase, T phase, and C phase, while that of ScYSZ ceramic coating was still a single T′ phase, indicating ScYSZ ceramic coating had better T′ phase stability, which could be attributed to the co-doping system of Sc₂O₃ and Y₂O₃ facilitated the formation of defect clusters. In the thermal shock experiment, the thermal shock life of YSZ TBCs was 310 times, while that of ScYSZ TBCs was 370 times, indicating the latter had better thermal shock resistance. The difference in thermal shock resistance could be attributed to the different sintering resistance of ceramic coatings and the different growth rates of thermally grown oxide in the two TBCs. Furthermore, the thermal shock failure modes of YSZ TBCs and ScYSZ TBCs were different, the former was delamination, while the latter was delamination and shallow spallation.     

Thermal shock behavior of 8YSZ and double-ceramic-layer La2Zr2O7/8YSZ thermal barrier coatings fabricated by atmospheric plasma spraying

The single-ceramic-layer (SCL) 8YSZ (conventional and nanostructured 8YSZ) and double-ceramic-layer (DCL) La₂Zr₂O₇ (LZ)/8YSZ thermal barrier coatings (TBCs) were fabricated by plasma spraying on nickel-based superalloy substrates with NiCrAlY as the bond coat. The thermal shock behavior of the three as-sprayed TBCs at 1000 °C and 1200 °C was investigated. The results indicate that the thermal cycling lifetime of LZ/8YSZ TBCs is longer than that of SCL 8YSZ TBCs due to the fact that the DCL LZ/8YSZ TBCs further enhance the thermal insulation effect, improve the sintering resistance ability and relieve the thermal mismatch between the ceramic layer and the metallic layer at high temperature. The nanostructured 8YSZ has higher thermal shock resistance ability than that of the conventional 8YSZ TBC which is attributed to the lower tensile stress in plane and higher fracture toughness of the nanostructured 8YSZ layer. The pre-existed cracks in the surface propagate toward the interface vertically under the thermal activation. The nucleation and growth of the horizontal crack along the interface eventually lead to the failure of the coating. The crack propagation modes have been established, and the failure patterns of the three as-sprayed coatings during thermal shock have been discussed in detail.     

Microstructure evolution of Al-modified 7YSZ PS-PVD TBCs in thermal cycle

The PS-PVD method was used to prepare 7YSZ thermal barrier coatings (TBCs) and NiCrAlY bond coatings on a DZ40 M substrate. To prevent oxidation of the coating, magnetron sputtering was used to modify the surface of TBCs with an Al film. To explore the stability of TBCs during thermal cycling, water quenching was performed at 1100 °C, and ultralong air cooling for 16,000 cycles was performed. The results showed that before water quenching and air cooling, the top surface structure of the 7YSZ TBCs changed. After water quenching, the surface of the Al film was scoured and broken, the surface peeled off layer-by-layer, and cracks formed at the interface between the thermally grown oxide and NiCrAlY. During air cooling of the thermal cycle, the Al film reacted with O₂ in the air to form a dense Al₂O₃ top layer that coated the cauliflower-like 7YSZ surface and maintained the feather-like shape. At the same time, the TGO layer between 7YSZ and NiCrAlY grew and cracked. The two thermal cycles of water quenching and air cooling led to different failure mechanisms of TBCs. Water quenching failure was caused by layer-by-layer failure of the 7YSZ top coat, while air cooling failure occurred due to the internal cracking of the TGO layer at the 7YSZ/NiCrAlY interface and the failure of the TGO/NiCrAlY interface.     

Thermal shock behavior of a 8YSZ/CoCrAlYTaSi thermal sprayed barrier coating on GH202 superalloy

The thermal shock behavior of a thermal barrier coating (TBC) prepared by plasma spraying at 1100 °C was investigated. The TBC consisted of a double layer structure of 8YSZ/CoCrAlYTaSi. The morphology, microstructure, phases and the elemental distribution of the TBCs were characterized using scanning electron microscopy (SEM), transmission electron microscope (TEM), scanning transmission electron microscope (STEM), X-ray diffraction (XRD) and electron probe micro-analysis (EPMA). The characterization results showed that the film consisted primarily of metastable tetragonal phases (t′), and a large number of micro-cracks were present in the 8YSZ crystals. Following eighty-six thermal shock cycles of the specimens a large areal spallation was observed on the 8YSZ coating. The decreased concentration of yttrium at the coating interfaces weakened the inhibition of crystal growth and the phase transition of the Al₂O₃. The growth of TGO (Thermal growth oxide) and the diffusion into the 8YSZ coating produced deformation and stress in the ceramic coating. Tantalum appeared to absorb the oxygen that diffused into the coatings and delayed the growth of TGO in the interface between the CoCrAlYTaSi and substrate, which was beneficial to prolonging the life of the TBC.     

Gradient thermal cycling behavior of a thermal barrier coating system constituted by NiCoCrAlY bond coat and pure metastable tetragonal nano-4YSZ top coat

Pure metastable tetragonal (t’) phase 4YSZ top coats with thickness of 100 and 200 μm were deposited on NiCoCrAlY-coated second generation single crystal superalloy by air plasma spray (APS). The two thermal barrier coatings were evaluated under gradient thermal cycling test using gas mixture of propane and oxygen. After flame shock test, the values of Young's modulus, hardness and degree of densification all exhibited a gradient distribution across YSZ thickness. In contrast to intensive sintering at surface of 200 μm 4YSZ coating, the TBC sample with 4YSZ layer of 100 μm underwent poor oxidation at interface of YSZ and bond coat, forming a duplex oxide scale: (Ni,Co)(Cr,Al)₂O₄ spinel over Al₂O₃, which promoted the delamination at the top-coat/bond-coat interface. The resistance against gradient thermal cycling, the phase stability of 4YSZ and the failure mechanism of the TBCs, were discussed correlating to the effects of YSZ thickness.     

Thermal cycling behavior and bonding strength of single-ceramic-layer Sm2Zr2O7 and double-ceramic-layer Sm2Zr2O7/8YSZ thermal barrier coatings deposited by atmospheric plasma spraying

The single-ceramic-layer (SCL) Sm₂Zr₂O₇ (SZO) and double-ceramic-layer (DCL) Sm₂Zr₂O₇ (SZO)/8YSZ thermal barrier coatings (TBCs) were deposited by atmospheric plasma spraying on nickel-based superalloy substrates with NiCoCrAlY as the bond coat. The mechanical properties of the coatings were evaluated using bonding strength and thermal cycling lifetime tests. The microstructures and phase compositions of the coatings were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. The results show that both coatings demonstrate a well compact state. The DCL SZO/8YSZ TBCs exhibits an average bonding strength approximately 1.5 times higher when compared to the SCL SZO TBCs. The thermal cycling lifetime of DCL SZO/8YSZ TBCs is 660 cycles, which is much longer than that of SCL 8YSZ TBCs (150 cycles). After 660 thermal cycling, only a little spot spallation appears on the surface of the DCL SZO/8YSZ coating. The excellent mechanical properties of the DCL LZ/8YSZ TBCs can be attributed to the underlying 8YSZ coating with the combinational structures, which contributes to improve the toughness and relieve the thermal mismatch between the ceramic layer and the metallic bond coat at high temperature.     

Microstructure and thermal cycling behavior of thermal barrier coating on near-α titanium alloy

Two kinds of thermal barrier coatings (TBCs), consisting of NiCoCrAlY bond coats (BCs) deposited by electron beam-physical vapor deposition (EB-PVD) and high velocity oxy-fuel (HVOF) thermal spraying, respectively, and top 8 wt%Y₂O₃–ZrO₂ (8YSZ) ceramic layers deposited by EB-PVD were prepared on near-α titanium alloys. The field emission scanning electronic microscopy and microhardness indentation are used to study the microstructure and microhardness. Different failure features including cracking patterns and the delamination degree of these two TBCs are discussed according to the thermal cycling tests in the atmosphere. It is found that the morphology of the two BCs deposited by different methods (EB-PVD and HVOF) determines the microstructure and microhardness of their corresponding top 8YSZ layers. The BC prepared by EB-PVD is dense and homogeneous, which leads to a dense and hard 8YSZ with clustered slim columnar grains. The BC prepared by HVOF, however, is porous and inhomogeneous in microstructure and, as a result, the top ceramic layer is loose with low microhardness and clustered coarse columnar grains.     

Comparison of thermal shock resistances of plasma-sprayed nanostructured and conventional yttria stabilized zirconia thermal barrier coatings

The main goal of the current study is evaluation and comparison of thermal shock behavior of plasma-sprayed nanostructured and conventional yttria stabilized zirconia (YSZ) thermal barrier coatings (TBCs). To this end, the nanostructured and conventional YSZ coatings were deposited by atmospheric plasma spraying (APS) on NiCoCrAlY-coated Inconel 738LC substrates. The thermal shock test was administered by quenching the samples in cold water of temperature 20–25 °C from 950 °C. In order to characterize elastic modulus of plasma-sprayed coatings, the Knoop indentation method was employed. Microstructural evaluation, elemental analysis, and phase analysis were performed using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffractometry (XRD) respectively. The results revealed that failures of both nanostructured and conventional TBCs were due to the spallation of ceramic top coat. Thermal stresses caused by mismatch of thermal expansion coefficients between the ceramic top coat and the underlying metallic components were recognized as the major factor of TBC failure. However, the nanostructured TBC, due to bimodal unique microstructure, presented an average thermal cycling lifetime that was approximately 1.5 times higher than that of the conventional TBC.     

Thermal cycling performances of multilayered yttria-stabilized zirconia/gadolinium zirconate thermal barrier coatings

Gadolinium zirconate (Gd₂Zr₂O₇, GZO) as an advanced thermal barrier coating (TBC) material, has lower thermal conductivity, better phase stability, sintering resistance, and calcium-magnesium-alumino-silicates (CMAS) attack resistance than yttria-stabilized zirconia (YSZ, 6-8 wt%) at temperatures above 1200°C. However, the drawbacks of GZO, such as the low fracture toughness and the formation of deleterious interphases with thermally grown alumina have to be considered for the application as TBC. Using atmospheric plasma spraying (APS) and suspension plasma spraying (SPS), double-layered YSZ/GZO TBCs, and triple-layered YSZ/GZO TBCs were manufactured. In thermal cycling tests, both multilayered TBCs showed a significant longer lifetime than conventional single-layered APS YSZ TBCs. The failure mechanism of TBCs in thermal cycling test was investigated. In addition, the CMAS attack resistance of both TBCs was also investigated in a modified burner rig facility. The triple-layered TBCs had an extremely long lifetime under CMAS attack. The failure mechanism of TBCs under CMAS attack and the CMAS infiltration mechanism were investigated and discussed.     

Thermal shock resistance of thermal barrier coatings modified by selective laser remelting and alloying techniques

Aiming to improve the thermal shock resistance of thermal barrier coatings (TBCs), the plasma-sprayed 7YSZ TBCs were modified by selective laser remelting and selective laser alloying, respectively, in this study. A self-healing agent TiAl₃ was introduced into the 7YSZ TBCs by selective laser alloying to fill cracks during thermal cycling. The thermal shock experiments of the plasma-sprayed, laser-remelted, and laser-alloyed TBCs were conducted by a means of heating and water-quenching method. Results revealed that some segmented microcracks were distributed on the surface of the laser-remelted and the laser-alloyed zones, showing a dense columnar crystal structure. After thermal shock tests, the numbers of segmented microcracks on the laser-remelted coating increased, whereas, in the laser-alloyed condition, some irregular particles formed, leading to the decreased numbers of segmented microcracks. The laser-alloyed coating exhibited the best thermal shock resistance, followed by the laser-remelted condition, with the thermal shock lifetime 3.3 and 2.7 times higher than that of the as-sprayed coating, respectively. On the one hand, both columnar grains and segmented microcracks in the laser-treated zone could effectively improve the strain tolerance of coatings. On the other hand, the oxidation products of TiAl₃ under high-temperature condition could seal the microcracks to postpone the crack connection. Thus, the thermal shock resistance of the laser-treated coatings was significantly improved.     

CMAS corrosion resistance,thermal shock resistance and numerical simulation of novel surface micromesh thermal barrier coatings

Thermal barrier coatings (TBCs) are widely used as insulating layers to protect the underlying metallic structure of gas turbine blades. However, the thermal cycling performance of TBCs is affected by their complex working environments, which may shorten their service life. Previous studies have shown that preparing a mesh structure in the bonding layer can relieve thermal stress and improve the bonding strength, thereby prolonging the service life of TBCs. In this paper, a micromesh structure was prepared on the surface of the bonding layer via wet etching. The microstructure and failure mechanism of the micromesh TBCs after CMAS (CaO-MgO-Al₂O₃-SiO₂) thermal erosion were investigated. Numerical simulation was combined with thermal shock experiments to study the stress distribution of the micromesh-structured TBCs. The results showed that the circular convex structure can effectively improve the CMAS corrosion resistance and thermal shock resistance of TBCs.     

Thermal shock performance and failure behavior of Zr6Ta2O17-8YSZ double-ceramic-layer thermal barrier coatings prepared by atmospheric plasma spraying

Zr₆Ta₂O₁₇ has higher fracture toughness, better phase stability, thermal insulation performance and calcium-magnesium-alumino-silicates (CMAS) attack resistance than yttria-stabilized zirconia (8 YSZ, 7–8 wt%) at temperatures above 1200 °C. However, the thermal expansion coefficients between Zr₆Ta₂O₁₇ coating and bond coating do not match well. A double-ceramic-layer design is applied to alleviate the thermal stress mismatch. The Zr₆Ta₂O₁₇/8 YSZ double-ceramic-layer thermal barrier coatings (TBCs) are prepared by atmospheric plasma spraying (APS). During the thermal shock test, Zr₆Ta₂O₁₇/8 YSZ double-ceramic-layer TBCs exhibit a better thermal shock resistance than 8 YSZ and Zr₆Ta₂O₁₇ single-layer TBCs. The thermal shock performance and failure mechanism of TBCs in the thermal shock test are investigated and discussed in detail.     

LZC/YSZ DCL TBCs by EB-PVD: Microstructure,low thermal conductivity and high thermal cycling life

Thermal barrier coatings (TBCs) with low thermal conductivity have triggered tremendous attention due to their promising application in the gas turbine engines. Albeit recent studies have investigated double ceramic layers (DCL) with pyrochlore (A₂B₂O₇) phase, it still remains a big challenge for controlling element content and investigating the relationship between the complex hierarchical architectures and their thermal performances. Here we describe a series of DCL La₂O₃-ZrO₂-CeO₂ (LZC)/Y₂O₃-stabilized ZrO₂ (YSZ) coating under different current of electron beam by electron beam-physical vapor deposition (EB-PVD). The formation of hierarchical architecture with feathery microstructure and intra-columnar have been investigated in detail. The DCL coatings achieve a high thermal cycling life and relatively low thermal conductivity at controlling current of electron beam from 1.0 A to 1.3 A. This work may open new opportunities to rationally design other promising TBCs.     

CMAS corrosion resistance in high temperature and rainwater environment of double-layer thermal barrier coatings odified by rare earth

In order to explore the difference of CMAS corrosion resistance in high temperature and rainwater environment of single-layer and double-layer thermal barrier coatings (TBCs), and further reveal the mechanism of CMAS corrosion resistance in above environment of double-layer TBCs modified by rare earth, two TBCs were prepared by air plasma spraying, whose ceramic coating were single-layer ZrO₂–Y₂O₃ (YSZ) and double-layer La₂Zr₂O₇(LZ)/YSZ, respectively. Subsequently, CMAS corrosion resistance tests at 1200 °C and rainwater environment of two TBCs were carried out. Results demonstrate that after high temperature CMAS corrosion for the same time, due to phase transformation, the volume of YSZ ceramic coating in single-layer TBCs shrank and surface cracks formed, which would lead to coating failure. When LZ ceramic coating of double-layer TBCs reacted with CMAS, compact apatite phases and fluorite phases formed, the penetration of CMAS into ceramic coating was inhibited effectively. Raman analysis and calculation results show that both of the surface residual stress of ceramic coating in two TBCs were compressive stress, and the residual stress of ceramic coating in double-layer TBCs were smaller than that of single-layer TBCs. Atomic force microscopy of TBCs after CMAS corrosion show that surface of double-layer TBCs was more uniform and compact than that of single-layer TBCs. The electrochemical properties in simulated rainwater of two TBCs after high temperature CMAS corrosion showed that double-layer TBCs possessed higher free corrosion potential, lower corrosion current and higher polarization resistance than those of single-layer TBCs. Consequently, the presence of LZ ceramic coating effectively improved CMAS corrosion resistance in high temperature and rainwater environment of double-layer TBCs.     

Comparative study on thermal shock behavior of thick thermal barrier coatings fabricated with nano-based YSZ suspension and agglomerated particles

Two kinds of segmentation-crack structured YSZ thick thermal barrier coatings (TTBCs) were deposited by suspension plasma spraying (SPS) and atmospheric plasma spraying (APS) with nano-based suspension and agglomerated particles, respectively. The phase composition, microstructure evolution and failure behavior of both TBCs before and after thermal shock tests were systematically investigated. Microstructure of the APS coating exhibits typical segmentation-crack structure in the through-thickness direction, similar with the SPS coating. The densities of segmentation-crack in APS and SPS coatings were about 3 cracks mm⁻¹ and 4 cracks mm⁻¹_, respectively. The microstructure observation also showed that the columnar and equiaxed grains existed in the SPS coating. As for the thermal shock test, the spallation life of the APS TTBCs was 146 cycles, close to that of the SPS TTBCs (166 cycles). Failure of the APS coating is due to the spallation of fringe segments and splats.     

Phase stability,thermo-physical properties and thermal cycling behavior of plasma-sprayed CTZ,CTZ/YSZ thermal barrier coatings

ZrO₂ co-stabilized by CeO₂ and TiO₂ with stable, nontransformable tetragonal phase has attracted much attention as a potential material for thermal barrier coatings (TBCs) applied at temperatures >?1200?°C. In this study, ZrO₂ co-stabilized by 15?mol% CeO₂ and 5?mol% TiO₂ (CTZ) and CTZ/YSZ (zirconia stabilized by 7.4?wt% Y₂O₃) double-ceramic-layer TBCs were respectively deposited by atmospheric plasma spraying. The microstructures, phase stability and thermo-physical properties of the CTZ coating were examined using scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric-differential scanning calorimeter (TG-DSC), laser pulses and dilatometry. Results showed that the CTZ coating with single tetragonal phase was more stable than the YSZ coating during isothermal heat-treatment at 1300?°C. The CTZ coating had a lower thermal conductivity than that of YSZ coating, decreasing from 0.89?W?m^?1 K^?1 to 0.76?W?m^?1 K^?1 with increasing temperature from room temperature to 1000?°C. The thermal expansion coefficients were in the range of 8.98?×?10^?6 K^?1 – 9.88 ×10^?6 K^?1. Samples were also thermally cycled at 1000?°C and 1100?°C. Failure of the TBCs was mainly a result of the thermal expansion mismatch between CTZ coating and superallloy substrate, the severe coating sintering and the reduction-oxidation of cerium oxide. The thermal durability of the TBCs at 1000?°C can be effectively enhanced by using a YSZ buffer layer, while the thermal cycling life of CTZ/YSZ double-ceramic-layer TBCs at 1100?°C was still unsatisfying. The thermal shock resistance of the CTZ coating should be improved; otherwise the promising properties of CTZ could not be transferred to a well-functioning coating.     

Laser thermal gradient testing of air plasma sprayed multilayered,multi-material thermal barrier coatings

Air plasma sprayed (APS) thermal barrier coatings (TBCs) are a widely used technology in the gas turbine industry to thermally insulate and protect underlying metallic superalloy components. These TBCs are designed to have intrinsically low thermal conductivity while also being structurally compliant to withstand cyclic thermal excursions in a turbine environment. This study examines yttria-stabilized zirconia (YSZ) TBCs of varying architecture: porous and dense vertically cracked (DVC), which were deposited onto bond-coated superalloys and tested in a novel CO₂ laser rig. Additionally, multilayered TBCs: a two-layered YSZ (dense + porous) and a multi-material YSZ/GZO TBC were evaluated using the same laser rig. Cyclic exposure under simulative thermal gradients was carried out using the laser rig to evaluate the microstructural change of these different TBCs over time. During the test, real-time calculations of the normalized thermal conductivity of the TBCs were also evaluated to elucidate information about the nature of the microstructural change in relation to the starting microstructure and composition. It was determined that porous TBCs undergo steady increases in conductivity, whereas DVC and YSZ/GZO systems experience an initial increase followed by a monotonic decrease in conductivity. Microstructural studies confirmed the difference in coating evolution due to the cycling.     

Preparation and performance of thermal barrier coatings made of BNw-containing modified Nd2O3-doped yttria-stabilized zirconia

To enhance the fracture toughness and thermal shock resistance of the thermal barrier coatings (TBCs), detonation spraying has been used to prepare modified neodymium (Ⅲ) oxide (Nd₂O₃)-doped yttria-stabilized zirconia (YSZ) TBCs containing 20 vol% (D1 coating) and 30 vol% (D2 coating) of boron nitride whiskers (BNws). Analyses were performed using a scanning electron microscope (SEM), X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS), and a microhardness tester to examine the manner in which the doping content of different rare earth oxides affected the coating morphology, composition, and mechanical properties. The results denoted that the porosity of the D2 coating was 47.9% higher than that of the D1 coating; the whisker content was 30 vol% in the former and 20 vol% in the latter. The increased porosity reduced the microhardness and bond strength of the coating. However, the fracture toughness (KIC) of the D2 coating was increased to 2.67 MPa·m^1/2 because the whisker content was 8.5% higher than that in the D1 coating. The thermal cycling life of the D2 coating was 245 cycles, and its thermal shock resistance was 9.9% higher when compared with that of the D1 coating. A TBC with better overall performance was obtained when BNw reached 30 vol%.     

Thermal cycling behavior of nanostructured 8YSZ，SZ/8YSZ and 8CSZ/8YSZ thermal barrier coatings fabricated by atmospheric plasma spraying

The nanostructured single-ceramic-layer (SCL) 8YSZ thermal barrier coatings (TBCs), double-ceramic-layer (DCL) Sm₂Zr₂O₇ (SZ)/8YSZ and SZ doped with 8 wt% CeO₂ nanoscale particles (8CSZ)/8YSZ TBCs were fabricated by atmospheric plasma spraying (APS) on nickel-based superalloy substrates with NiCoCrAlY as the bond coating. The thermal cycling behavior of the three as-sprayed TBCs was investigated systematically at 1000 ℃ and 1200 ℃. The results reveal that the thermal cycling lifetime of the nanostructured DCL 8CSZ/8YSZ TBCs is the longest among them, which is largely due to the fact that the intermediate layer buffer effect of the DCL structure, more porosity and improvement of thermal expansion coefficient from doping CeO₂ nanoparticles can relieve thermal stress to a great extent at elevated temperature. The failure mechanism of the nanostructured TBCs has been discussed in detail.