Deformation characteristics of Ti–6Al–4V

Abstract

The deformation characteristics of Ti–6Al–4V have been established by torsion testing in the temperature range 800–1150°C. Constitutive equations are proposed for both the β-region and the α+β-region which, it is suggested, may have some practical applications. Extensive optical and electron microscopy have established that dynamic recovery is the operative deformation mode in the β-region, while dynamic recrystallisation predominates in the α+β-region.

MST/806     

In vitro behavior of layer-by-layer deposited molecular oligoelectrolyte films on Ti–6Al–4V surfaces

Layer-by-layer self-assembled films of molecular oligoelectrolytes were used to modify Ti–6Al–4V surfaces in order to test their ability as potential drug delivery system. With regard to medical application the in vitro behavior of the modified material was investigated. The Ti–6Al–4V (6% aluminium, 4% vanadium) material was treated in a layer-by-layer (LbL) process with 2, 4, 6 and 8 layers of molecular oligoelectrolytes 1 and 2 and thereby doped with a fluorescent reporter molecule 2. Human osteoblasts were cultured for a period up to 5 days on the modified material. Ti–6Al–4V surfaces without modification were used as control. In order to investigate the in vitro behavior of the coating as well as the influence of components of the coating on osteoblastic cells, respectively, cell proliferation, differentiation and attachment of hFOB cells were observed by means of cell number, osteoblastic gene expression and fluorescence microscopy. Degradation behavior of the OEM (oligoelectrolyte multilayer film) was examined using optical spectroscopy. Measurement data imply that the layer-by-layer coating was successfully assembled on the Ti surface and endures steam sterilization. The fluorescence signal in cell culture medium increased strictly linear with increasing pre-assembled number of layers on the surface. Proliferation rates of the cells in experimental groups did not differ significantly from each other (P ≥ 0.783). Differentiation pattern was not significantly changed by the coating. The fluorescent reporter component of the film was absorbed by osteoblastic cells and was detected by fluorescence microscopy.     

Laser surface modification for synthesis of textured bioactive and biocompatible Ca–P coatings on Ti–6Al–4V

A textured calcium phosphate based bio-ceramic coating was synthesized by continuous wave Nd:YAG laser induced direct melting of hydroxyapatite precursor on Ti–6Al–4V substrate. Two different micro-textured patterns (100 μm and 200 μm line spacing) of Ca–P based phases were fabricated by this technique to understand the alignment and focal adhesion of the bone forming cells on these surfaces. X-ray diffraction studies of the coated samples indicated the presence of CaTiO₃, α-Ca₃(PO₄)₂, Ca(OH)₂, TiO₂ (anatase) and TiO₂ (rutile) phases as a result of the intermixing between the precursor and substrate material during laser processing. A two dimensional elemental mapping of the cross-section of the coated samples exhibited the presence of higher phosphorous concentration within the coating and a thin layer of calcium concentration only at the top of the coating. Improved in vitro bioactivity and in vitro biocompatibility was observed for the laser processed samples as compared to the control.     

Effect of surface roughness on fatigue performance of additive manufactured Ti–6Al–4V

Additive manufacturing is increasingly considered for production of high quality, metallic, aerospace parts. Despite the high potential of this manufacturing process to reduce weight and lead time, the fundamental understanding of additive manufactured Ti–6Al–4V material is still at an early stage, especially in the area of fatigue and damage tolerance. This paper covers the effects of inherent surface roughness on the fatigue life. In the as built condition, metallic parts have a poor surface texture, which is generally removed in fatigue critical areas. It is shown that the fatigue properties of Ti–6Al–4V samples, produced by direct metal laser sintering and electron beam melting, are dominated by surface roughness effects. A simple model based on an equivalent initial flaw size is formulated.     

Microindentation study of Ti–6Al–4V alloy

In order to study the micromechanical behavior of Ti–6Al–4V alloy, microindentation experiments were performed with five different maximum loads of 100, 150, 200, 250 and 300 mN, and with three loading speeds of 6.4560, 7.7473 and 9.6841 mN/s respectively. The experimental results revealed that loading speed has little influence on microhardness and Young’s modulus. Microindentation hardness experiments showed strong indentation size effects, i.e. increase of indentation hardness with the decrease of indentation load or depth. Then microindentation constitutive equation that described the stress as a function of the strain was proposed through dimensional analysis. And the finite element simulation results showed that the predicted computational indentation data from developed constitutive equation can track the microindentation experimental data of Ti–6Al–4V alloy.     

Microplasticity in HCF of Ti–6Al–4V

Previous research has shown that Ti–6Al–4V exhibits pronounced stress ratio effects under high cycle fatigue (HCF) loading. At high stress ratios (R>0.7), a transition of failure mode occurs from traditional surface fatigue crack initiation and growth to bulk-dominated damage initiation and coalescence of multiple microcracks consistent with a ductile tensile test. At these high stress ratios, ratchetting was shown to occur (Int. J. Fatigue 21 (1999) 679; Mech. Time-Dependent Mater. 2 (1999) 195), leading to progressive strain accumulation until final failure. This study explores the microstructural origins of this stress ratio transition in HCF using computational micromechanics. The material being studied is a two-phase Ti–6Al–4V plate forging, consisting of a duplex microstructure with a hexagonal close-packed (hcp) α-phase and lamellar grains with layers of body-centered cubic (bcc) β-phase and secondary hcp α-phase. Crystallographic slip is the dominant mode of plastic deformation in this material. A 2-D crystal plasticity model that incorporates nonlinear kinematic and isotropic hardening at the slip system level is implemented into the finite element method to simulate the cyclic plasticity behavior. The finite element model is used to qualitatively understand the distribution of microplasticity in this alloy under various loading conditions. For typical HCF stress amplitudes, it is shown that microstructure scale ratchetting becomes dominant at R=0.8, but is insignificant at R=0.1 and 0.5. Reversed cyclic microplasticity is insignificant at all three stress ratios. The effects of phase morphology and orientation distribution are shown to affect the microscale plastic strain distribution in terms of the location and magnitudes of the plastic shear bands that form within clusters or chains of primary α grains. The results of the finite element modeling are also considered in light of previous experimental results.     

Formation of hydroxyapatite layer on bioactive Ti and Ti–6Al–4V by simple chemical technique

Bioactive coatings on cp-Ti and Ti–6Al–4V were prepared by a simple chemical technique. Specimens of cp-Ti and Ti–6Al–4V were initially immersed in a 5 M NaOH solution at 60 °C for 24 h which resulted in the formation of a porous network structure composed of Na₂Ti₅O₁₁ and TiO₂. The specimens were then immersed in a Ca-rich solution either at 60 °C or at 36.5 °C for 24 h. During this treatment Na⁺ was released and Ti–OH groups were formed. Subsequently, TiO₂ dissociated from the Ti–OH group and combined with calcium ions to form calcium titanate (CaTiO₃), which was embedded in a titania gel layer during the immersion period. The specimens were then immersed in r-SBF at 36.5 °C for 1–30 days. After immersion in r-SBF for 3 days, HAp (hydroxyapatite) spheroids began to deposit on the substrates, and within a week the surfaces were covered. The HAp spheroids were 5 μm in size with a Ca/P ratio of 1.68 which was close to bone-like apatite (1.67). The average thicknesses of HAp layer after immersion in r-SBF for 3 days, 1 week, and 2 weeks were 3.8, 5.6, and 6.4 μm, respectively. A scratch test, used to evaluate the adhesive strength of the HAp layer, showed that the HAp layer was not scraped off until the applied load reached 26 N.     

Tribological Performance of Titanium Alloy Ti–6Al–4V via CVD–diamond Coatings

In the present study, HFCVD nanocrystalline, microcrystalline and boron-doped nanocrystalline diamond coatings have been deposited on titanium alloy. The effect of boron doping on coefficient of friction and residual stresses of diamond coatings have been studied. The tribological characteristics of the aforementioned three coatings on Ti–6Al–4V substrates were studied using ball on disc micro-tribometer, the thickness of the coatings being 3 μm. The coated Ti–6Al–4V discs were slid against alumina (Al₂O₃) balls with normal load ranging from 1 to 10 N. The boron-doped NCD coated sample disc was found to possess the lowest average coefficient of friction ~ 0.0804 while the undoped NCD and MCD coated sample discs were found to possess the average coefficients of friction of ~ 0.143 and ~ 0.283, respectively. Raman spectroscopy studies revealed that the residual stresses in boron-doped nanocrystalline coatings were tensile in nature, while the residual stresses in undoped NCD and MCD were found to be of compressive nature.     

Laser welding of Ti–6Al–4V to Nitinol

Formation of brittle intermetallic phases in addition to different thermal expansion coefficients associated with dissimilar welding leads to the formation of transverse cracks in weld metal and eventually restricts widespread applications of dissimilar joints. Therefore, joining technology should be expanded in field of dissimilar welding in order to solve its difficulties. In the present study, an experimental work with pulsed Nd:YAG laser was performed for dissimilar welding of Ti–6Al–4V and Nitinol. Autogenous welding of these two alloys resulted in joints with poor strength and ductility due to the formation of transverse cracks in the weld metal. Therefore, the chemical composition of the weld metal has to be modified in order to reduce the formation of brittle phases and eliminate subsequent cracking. In this work, this was done by insertion of a copper interlayer with a thickness of 75 μm between the base metals. The results indicated that insertion of copper interlayer has a great influence on the reduction of the amount of Ti₂Ni brittle intermetallic phase, elimination of transverse cracks through the weld metal and eventually improvement of mechanical properties of the joints. Insertion of copper interlayer was very useful since it altered the cracked autogenous joint to a joint which could withstand a tensile stress of 300 MPa.     

Corrosion behavior of Ti–8Al–1Mo–1V alloy compared to Ti–6Al–4V

The corrosion behavior of Ti–8Al–1Mo–1V alloy was investigated in 3.5% NaCl and 5% HCl solutions. Corrosion properties of Ti–6Al–4V alloy were also evaluated under the same conditions for comparison. It was found that both Ti–8Al–1Mo–1V and Ti–6Al–4V alloys exhibited spontaneous passivity and low corrosion current densities in 3.5% NaCl solution. The potentiodynamic polarization curves obtained in 5% HCl solution revealed an active–passive transition behavior and similar corrosion rates for the examined alloys. However, the results of the weight loss experiments under accelerated immersion conditions (5 M HCl at 35 °C) indicated that Ti–8Al–1Mo–1V alloy exhibited inferior corrosion behavior compared to Ti–6Al–4V alloy. These results were confirmed by scanning electron microscopy (SEM) analysis of the samples after immersion tests which revealed that the β phase was corroded preferentially for both alloys, but to a larger extent in the case of Ti–8Al–1Mo–1V alloy.     

Microstructures and mechanical properties of electron beam-rapid manufactured Ti–6Al–4V biomedical prototypes compared to wrought Ti–6Al–4V

This study represents an exploratory characterization and comparison of electron-beam melted (EBM) or rapid manufacturing (RM) of Ti–6Al–4V components (from nominal 30 μm diameter powder) with wrought products. Acicular α and associated β microstructures observed by optical metallography and electron microscopy (SEM and TEM) are compared along with corresponding tensile test and hardness data; including the initial powder particles where the Vickers microindentation hardness averaged 5.0 GPa in comparison with the fully dense, EB manufactured product with an average microindentation hardness ranging from 3.6 to 3.9 GPa. This compared with wrought products where the Vickers microindentation hardness averaged 4.0 GPa. Values of UTS for the EBM samples averaged 1.18 GPa for elongations ranging from 16 to 25%. Biomaterials/biomedical applications of EBM prototypes in direct prosthesis or implant manufacturing from CT or MRI data are discussed in the context of this work, especially prospects for tailoring physical properties through EB control to achieve customized and optimized implant and prosthetic products direct from CT-scans.     

Surface modification of Ti–6Al–4V alloy for biomineralization and specific biological response: Part I,inorganic modification

Titanium and its alloys represent the gold standard for orthopaedic and dental prosthetic devices, because of their good mechanical properties and biocompatibility. Recent research has been focused on surface treatments designed to promote their rapid osteointegration also in case of poor bone quality. A new surface treatment has been investigated in this research work, in order to improve tissue integration of titanium based implants. The surface treatment is able to induce a bioactive behaviour, without the introduction of a coating, and preserving mechanical properties of Ti6Al4V substrates (fatigue resistance). The application of the proposed technique results in a complex surface topography, characterized by the combination of a micro-roughness and a nanotexture, which can be coupled with the conventional macro-roughness induced by blasting. Modified metallic surfaces are rich in hydroxyls groups: this feature is extremely important for inorganic bioactivity (in vitro and in vivo apatite precipitation) and also for further functionalization procedures (grafting of biomolecules). Modified Ti6Al4V induced hydroxyapatite precipitation after 15 days soaking in simulated body fluid (SBF). The process was optimised in order to not induce cracks or damages on the surface. The surface oxide layer presents high scratch resistance.     

Photocatalytic activity of low temperature oxidized Ti–6Al–4V

Numerous advanced surface modification techniques exist to improve bone integration and antibacterial properties of titanium based implants and prostheses. A simple and straightforward method of obtaining uniform and controlled TiO₂ coatings of devices with complex shapes is H₂O₂-oxidation and hot water aging. Based on the photoactivated bactericidal properties of TiO₂, this study was aimed at optimizing the treatment to achieve high photocatalytic activity. Ti–6Al–4V samples were H₂O₂-oxidized and hot water aged for up to 24 and 72 h, respectively. Degradation measurements of rhodamine B during UV-A illumination of samples showed a near linear relationship between photocatalytic activity and total treatment time, and a nanoporous coating was observed by scanning electron microscopy. Grazing incidence X-ray diffraction showed a gradual decrease in crystallinity of the surface layer, suggesting that the increase in surface area rather than anatase formation was responsible for the increase in photocatalytic activity.     

Fatigue Resistance of Powder Metallurgy Ti–6Al–4V Alloy

Fatigue-resistance characteristics of Ti–6Al–4V alloy synthesized by the simplest powder metallurgy method involving the processes of pressing and sintering of blended elemental titanium hydride-based powders were studied. Powder materials have a relatively fine-grain -phase, which despite the presence of residual pores, makes for quite a high fatigue limit (500 MPa) comparable to that of the corresponding cast alloys. Fatigue cracks in the powder alloys are initiated from such stress raisers as major pores open to the surface of the specimen gauge length. Along with a significant decrease in the production costs of titanium alloys and articles of them, the use of this method provides obtaining materials with satisfactory static and dynamic mechanical characteristics suitable for practical applications.     

Post-forming tensile properties of superplastic Ti–6Al–4V alloy

Abstract

A study has been made of the influence of uniaxial superplastic deformation on the ambient temperature tensile properties of Ti–6Al–4V sheet. Material was deformed to various strains up to 200% at temperatures from 850 to 970°C at strain rates in the range 1·1?18 × 10^{;amp;#x2212;4}s^?1 (0·7?11% min^?1). Tests were also performed on statically annealed material to separate the effects of high temperature exposure and superplastic deformation. Mechanical property changes were complex and depended on the relative contributions from the strengthening and softening mechanisms occurring during either superplastic deformation or heat cycling. Structural features influencing mechanical properties were phase size and morphology, dislocation density, and crystallographic texture. The strength after superplastic deformation was always less than that of as-received material but a significant reduction in strength was attributable to heat cycling. In some cases, the strength of the superplastically deformed material was greater than that after heat cycling.

MST/593     

Investigation of joining Al–C–Ti cermets and Ti6Al4V by combustion synthesis

The paper has addressed a route for the welding of titanium alloy (Ti6Al4V) and Al–C–Ti powders by the combustion synthesis (CS) method. Al–C–Ti powders were compressed in the titanium alloy pipes with relative densities of 65%, and then the powder compact was sintered by two reaction mode at the same time as the annulus of titanium alloy and the synthesized product were joined. The paper has studied the effects of reaction mode and Al content in starting powders on the structure and property of the welded joints. And it has also discussed the microstructure of welded joints by laser-induced combustion synthesis (LCS). The mechanical properties of the welding seam have been also tested. The results show that LCS welding has realized fusion welding and the welding seam has good mechanical properties. Furthermore, SEM analysis has indicated that nano-size grains of TiC were formed in the joint layer.     

Effect of severe plastic deformation on creep behaviour of a Ti–6Al–4V alloy

This paper examines the effect of severe plastic deformation on creep behaviour of a Ti–6Al–4V alloy. The processed material with an ultrafine-grained (UFG) structure (d ≈ 150 nm) was prepared by multiaxial forging. Uniaxial constant stress compression and constant load tensile creep tests were performed at 648–698 K and at stresses ranging between 300 and 600 MPa on the UFG processed alloy and, for comparison purposes, on its coarse-grained (CG) state. The values of the stress exponents of the minimum creep rate n and creep activation energy Q _c were determined. Creep behaviour was also investigated by nanoindentation method at room temperature under constant load. The microstructure was examined by transmission electron microscopy and scanning electron microscope equipped with an electron back scatter diffraction unit. The results of the uniaxial creep tests showed that the minimum creep rates of the UFG specimens are significantly higher in comparison with those of the CG state. However, the differences in the minimum creep rates of both states of alloy strongly decrease with increasing values of applied stress. The CG alloy exhibits better creep resistance than the UFG one over the stress range used; the minimum creep rate for the UFG alloy is about one to two orders of magnitude higher than that of the CG alloy. The indentation creep tests showed that annealing had little effect on the creep behaviour in UFG Ti alloy at room temperature.