对失活Co-Mo-K/Al2O3硫化物催化剂的剖析研究

本文通过多种测试技术研究了工业Co -Mo -K Al2 O3 耐硫变换催化剂 ,失活样中各元素的存在状态、含量和物相变化。发现 ,在原催化剂中钾、硫从内部向表面迁移并有流失 ,γ -Al2 O3 转变为 (Al2 O3 ) 10R ,MoS2 、Co9S8变为含活性硫物种少的物相 ;从反应气中夹带的铁、铬、硅和镍杂质沉积在表面上。由此导致催化剂对H2 O和CO的吸附与反应能力的下降 ,最终造成严重失活。     

对失活Co—Mo—D／Al2O3硫化物催化剂的剖析研究

本文通过多种测试技术研究了工业Co-Mo-K/Al2O3耐硫变换催化剂,失活样中各元素的存在状态,含量和物相变化。发现,在原催化剂中钾、,硫从内部向表面迁移并有流失,γ－Al2O3转变为（Al2O3)10R,MoS2,Co9S8变为含活性硫物种少的物相;从反应气中夹带的铁,铬,硅和镍杂质沉积在表面上,由此导致催化剂对H2O和CO的吸附与反应能力的下降,最终造成严重失活。     

KF/Al2O3催化合成肉桂醛研究

研究了用KF/Al     

Co-Mo-K/Al2O3系耐硫变换催化剂硫化过程的研究

以工厂实用的加有CS₂的半水煤气为硫化气源,采用TG、DTA、SEM、EDS、XRD等表征技术,对Co-Mo-K/Al₂O₃系耐硫变换催化剂的各个组份及其组合试样进行了恒温硫化及程序升温硫化实验研究。全面考察了温度对硫化过程的影响,比较了不同活住组份的硫化行为,探讨了各组份在硫化过程中的作用。     

丙三醇水蒸气重整制氢M/Al2O3催化剂

以Al2O3为载体,采用浸渍法制备了Cu、Co、Ni、Pt/Al2O3四种单一组分催化剂(M/Al2O3)。研究了M/Al2O3催化剂对丙三醇水蒸气重整制氢反应的适用性及反应行为;考察了制备条件及还原条件,通过活性、稳定性及抗积炭性进行了催化剂的活性评价,并对催化剂进行了TPR、XRD表征。研究发现M/Al2O3催化剂用于丙三醇水蒸气重整制氢均表现出一定活性;其中Cu/Al2O3催化剂具有一定的抗积炭性;Pt/Al2O3催化剂表现出较好的抗积炭性、高温活性,但稳定性较差;Co/Al2O3催化剂表现出较好的稳定性;Ni/Al2O3催化剂表现出较好的低温活性。     

Fe2O3/Ni2O3/Al2O3催化剂制备及其催化氧化靛蓝废水研究

以三氧化二铝为载体,采用浸渍沉淀法制备系列Fe2O3/Ni2O3/Al2O3催化剂。采用TG-DTA,XRD及ESEM等技术对催化剂进行表征,确定催化剂的最佳焙烧温度为460℃。以次氯酸钠为氧化剂,同时考察m(三氧化二镍)/m(三氧化二铝)、m(三氧化二铁)/m(三氧化二镍)、m(次氯酸钠)∶m(靛蓝废水)、pH对印染靛蓝废水处理的影响。结果表明:m(三氧化二镍)/m(三氧化二铝)=0.3,m(三氧化二铁)/m(三氧化二镍)=0.04,m(次氯酸钠)∶m(靛蓝废水)=1∶11,pH=7,反应温度为20℃,常压反应时间为2 h时,COD的去除率为95.3%。     

CuNi/Al2O3催化剂上乙炔选择加氢的研究

采用浸渍法制备了CuNi/Al2O3催化剂,研究了Ni负载量、Cu负载量及n(Cu)/n(Ni)对催化剂上乙炔选择加氢活性和选择性的影响,以及催化剂的还原性能。结果表明:CuNi/Al2O3催化剂中Cu提高了Ni的还原性,使催化剂具有很高的活性及乙烯选择性。随Cu/Ni原子比的提高,催化剂的活性下降,选择性升高,当Ni的负载量为10%、n(Cu)/n(Ni)=0.5时,在反应温度为50℃、反应压力为0.2 MPa、原料气流量为45 mL/min及H2流量为1.5 mL/min的反应条件下,乙炔的转化率达88.98%,乙烯的选择性达74.01%,乙烯收率为65.86%。     

Ru/Al2O3催化剂表面分形分析

利用静态氮吸附仪在-196.15 ℃液氮气氛中,测定Ru/Al2O3催化剂的比表面积以及孔结构参数,研究了催化剂的孔容-孔径分布和吸附-脱附等温线。基于FHH多层吸附模型,利用全吸附数据计算出Ru/Al2O3催化剂的表面分形维数。结果表明,3种Ru/Al2O3催化剂的表面分形维数均约2.4,分形维数与比表面积和总孔体积无直接关联。     

MgO/Al2O3比对铝镁浇注料性能的影响

以一级高铝矾土熟料、中档轻烧镁砂和Al2O3超微粉等为主要原料,研究了MgO/Al2O3比对铝镁浇注料性能的影响.结果表明当MgO/Al2O3比接近于镁铝尖晶石的理论组成时,浇注料试样的综合性能较好.     

添加ZrO2的Pd/Al2O3催化剂及其催化蒽醌加氢性能

以四氯合钯（II）酸（H2PdCl4）为前体,活性氧化铝（Al2O3）为载体,硝酸锆（Zr（NO3）4）为添加组分,采用不同方式的分步浸渍法制备了添加ZrO2的Pd/Al2O3催化剂。考察了制备方法和反应条件对催化剂蒽醌加氢催化性能的影响,发现催化剂活性与制备方法有关。当对添加锆的载体进行适当焙烧,控制Pd负载量为0.3%,还原温度低于300℃时,催化剂的蒽醌加氢活性较高,与未添加ZrO2的催化剂相比提高了约20%。X射线衍射（XRD）、氮气物理吸附（BET）、透射电镜（TEM）、X光电子能谱（XPS）和程序升温还原（TPR）等表征对催化剂物相结构、比表面积、表面形貌及组分间相互作用的分析表明,ZrO2的掺杂提高了载体Al2O3的高温稳定性,改善了催化剂中活性组分Pd与载体间的相互作用,促进了Pd在载体表面的分散,从而提高了催化活性。     

Effect of Al2O3 on mechanical properties of Ti3SiC2/Al2O3 composite

The effect of Al₂O₃ on mechanical properties of Ti₃SiC₂/Al₂O₃ composite fabricated by SPS was studied systematically. The results show that the hardness of the Ti₃SiC₂/Al₂O₃ composite can reach 10.28 GPa, 50% higher than that of pure Ti₃SiC₂. However, slight decrease in the other mechanical properties was observed with Al₂O₃ addition higher than 5–10 vol.%, which is believed to be due to the agglomeration of Al₂O₃ in the composite.     

Characterization and tribological investigation of sol-gel Al2O3 and doped Al2O3 films

Thin films of Al₂O₃ and doped Al₂O₃ were prepared on a glass substrate by dip coating process from specially formulated ethanol sols. The morphologies of the unworn and worn surfaces of the films were observed with atomic force microscope (AFM) and scanning electron microscope (SEM). The chemical compositions of the obtained films were characterized by means of X-ray photoelectron spectroscopy (XPS). The tribological properties of obtained thin films sliding against Si₃N₄ ball were evaluated and compared with glass slide on a one-way reciprocating friction tester. XPS results confirm that the target films were obtained successfully. The doped elements distribute in the film evenly and exist in different kinds of forms, such as oxide and silicate. AFM results show that the addition of the doped elements changes the structure of the Al₂O₃ films, i.e., a rougher and smoother surface is obtained. The wear mechanisms of the films are discussed based on SEM observation of the worn surface morphologies. As the results, the doped films exhibit better tribological properties due to the improved toughness. Sever brittle fracture is avoided in the doped films. The wear of glass is characteristic of brittle fracture and severe abrasion. The wear of Al₂O₃ is characteristic of brittle fracture and delamination. And the wear of doped Al₂O₃ is characteristic of micro-fracture, deformation and slight abrasive wear. The introduction of ZnO is recommended to improve the tribological property of Al₂O₃ film.     

Effect of surface-modified Al2O3 on the thermomechanical properties of polybutylene succinate/Al2O3 composites

This study investigates the effect of the incorporation of alumina particles on the thermomechanical properties of polybutylene succinate (PBS)/Al₂O₃ composites. The alumina surface was modified with the carboxylic groups of maleic acid through simple acid-base and in situ polymerization reactions. Scanning electron microscope (SEM) results revealed the introduction of maleic acid treated alumina significantly affect the morphology of the PBS/Al₂O₃ composites as compared to the neat PBS. The thermal conductivity of the composite (0.411?W?m^?1 K^?1) was more than twice that of neat PBS. The composite containing polymerization-modified alumina showed a 50% increase in storage modulus compared with that of neat PBS. In addition, universal testing machine (UTM) and differential scanning calorimetry (DSC) measurements indicated an increase in the tensile strength and degree of crystallinity after the incorporation of modified alumina in the PBS/Al₂O₃ composite.     

Al2O3/Cu-O composites fabricated by pressureless infiltration of paper-derived Al2O3 porous preforms

Al₂O₃/Cu-O composites were fabricated from the paper-derived alumina matrix infiltrated with a Cu-3.2?wt% O alloy. Paper-derived alumina preforms with an open porosity ranging from ～ 14 to ～ 25?vol% were prepared by sintering of alumina-loaded preceramic papers at 1600?°C for 4?h. Pressureless infiltration at 1320?°C for 4?h of the preforms with Cu–O alloy resulted in the nearly dense materials with good mechanical and electrical properties, e.g. fracture toughness up to 6?MPa?m^0.5, four-point-bending strength up to 342?MPa, Young's modulus up to 281?GPa and electrical conductivity up to 2?MS/m depending on the volume fraction of copper alloy in the composites. The technological capability of this approach was demonstrated using prototypes in various engineering fields fabricated by lamination, corrugating and Laminated Object Manufacturing (LOM) methods.     

Fabrication and microstructure evolution of Al2O3/ZrBN-SiCN/Al2O3 high-temperature oxidation-resistant composite coating

The oxidation-resistance of thin film sensors, particularly at high temperatures, is critical for the lifetime and performance of the sensor. The preparation and oxidation-resistance of an Al₂O₃/ZrBN-SiCN/Al₂O₃ composite film with a sandwich-structure was performed using reactive magnetron sputtering. The microstructure evolution of the composite film is examined herein using X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) analysis. Oxygen diffusion was significantly inhibited by the formation of crystalline Al₂SiO₅ and Zr-B-C amorphous phase inside the composite film. The Pt-13%Rh/Pt thin film thermocouple (TFTC) with the Al₂O₃/ZrBN-SiCN/Al₂O₃ composite film as a protective layer was fabricated and calibrated. Both the stability and lifetime of the TFTC was significantly enhanced for temperatures up to 1000?℃. The test error of the TFTC was reduced by half, compared with that of the TFTC with the Al₂O₃ protective layer, indicating an excellent oxidation-resistant performance of the composite film.     

Influence of glass phase on Al2O3 fiber-reinforced Al2O3 composites processed by slip casting

The present work describes the processing of alumina fiber reinforced alumina ceramic preforms consisting of chopped Al₂O₃ fibers (33 wt%) and Al₂O₃ (67 wt%) fine powders by slip casting. The preforms were pre-sintered in air at 1100 °C for 1 h. A lanthanum based glass was infiltrated into these preforms at 1250 °C for 90 min. Linear shrinkage (%) was studied before and after glass infiltration. Pre-sintered and infiltrated specimens were characterized by scanning electron microscopy, energy dispersive X-ray, X-ray diffraction, porosimetry and flexural strength. The alumina preforms showed a narrow pore size distribution with an average pore size of ∼50 nm. It was observed that introducing Al₂O₃ fibers into Al₂O₃ particulate matrix produced warp free preforms with minor shrinkage during pre-sintering and glass infiltration. It was observed that the infiltration process fills up the pores and considerably improves the strength and reliability of alumina preform.     

Formation of alkoxy-derived 3Al2O3 · 2GeO2

Germanium-mullite (3Al₂O₃·2GeO₂) is formed directly as a single phase at lower temperatures from amorphous material with 50–66.7 mole% Al₂O₃ prepared by the alkoxy-method. The kinetic data of the 3Al₂O₃·GeO₂ crystallization with 50 and 60 mole% Al₂O₃ are represented by different solid-state equations. The difference of the crystallization mechanism is possibly explained in terms of the morphology of the 3Al₂O₃·GeO₂ particles.     

Deactivation patterns of Mo/Al2O3, Ni–Mo/Al2O3 and Ni–MoP/Al2O3 catalysts in atmospheric residue hydrodesulphurization

In the present work, a comparative study on the deactivation behavior of three types of industrial hydrotreating catalysts, namely, Mo/Al₂O₃, Ni–Mo/Al₂O₃ and Ni–MoP/Al₂O₃, that are used to promote primarily hydrodemetallization (HDM), hydrodesulphurization (HDS) and hydrodesulphurization + hydrodenitrogenation (HDS/HDN) reactions, respectively, in the first, second and third reactor of commercial atmospheric residue desulfurization (ARDS) units was carried out. The main objective of the study was to contribute to a better understanding of the relationship between catalyst type and catalyst deactivation patterns. The used catalysts from these experiments were fully characterized to determine the extent and the cause of deactivation. Special emphasis was paid to understanding the nature of the coke and metal deposition on the used catalysts by applying chemical analysis and various advanced analytical techniques, such as solid-state carbon-13 nuclear magnetic resonance spectroscopy (¹³C NMR), temperature-programmed oxidation (TPO), electron probe micro-analysis (EPMA), and diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy. The results are discussed scientifically based on the physico–chemical properties of the three catalysts.     

Laser stereolithography of ZrO2 toughened Al2O3

Ceramic laser stereolithography is a manufacturing process suitable candidate for the production of complex shape technical ceramics. The green ceramic is produced layer by layer through laser polymerisation of UV curable ceramic suspensions. A number of critical issues deserve attention: high solid loading and low viscosity of the suspensions, high UV reactivity, prevention of interlayer delamination in the green and in the sintered body, good mechanical performance. In this work, ZrO₂-reinforced Al₂O₃ components have been obtained from an acrylic modified zircon loaded with alumina powders. The zircon compound is effective as organic photoactivated resin and allows the dispersion of a high volume fraction of Al₂O₃ powder (up to 50 vol.%) while keeping viscosity at reasonable low values. The zircon compound also represents a liquid ceramic precursor that converts to oxide after burning out of the binder. Thank to the good dispersion of the alumina powder in the zircon acrylate, a uniform dispersion of ZrO₂ submicron particles is obtained after pyrolysis. These are located at the grain boundaries between alumina grains. Formation of both monoclinic and tetragonal ZrO₂ occurs as evidenced by XRD. No delamination occurs in bending tests as evidenced by SEM fractography, satisfactory modulus and strength values were concurrently found.