Tuning Hole Transport Layer Using Urea for High‐Performance Perovskite Solar Cells

Interface engineering is critical to the development of highly efficient perovskite solar cells. Here, urea treatment of hole transport layer (e.g., poly(3,4‐ethylene dioxythiophene):polystyrene sulfonate (PEDOT:PSS)) is reported to effectively tune its morphology, conductivity, and work function for improving the efficiency and stability of inverted MAPbI₃ perovskite solar cells (PSCs). This treatment has significantly increased MAPbI₃ photovoltaic performance to 18.8% for the urea treated PEDOT:PSS PSCs from 14.4% for pristine PEDOT:PSS devices. The use of urea controls phase separation between PEDOT and PSS segments, leading to the formation of a unique fiber‐shaped PEDOT:PSS film morphology with well‐organized charge transport pathways for improved conductivity from 0.2 S cm^?1 for pristine PEDOT:PSS to 12.75 S cm^?1 for 5 wt% urea treated PEDOT:PSS. The urea‐treatment also addresses a general challenge associated with the acidic nature of PEDOT:PSS, leading to a much improved ambient stability of PSCs. In addition, the device hysteresis is significantly minimized by optimizing the urea content in the treatment.     

Organic Semiconductors for Thermoelectric Applications

The thermoelectric performance of thin films fabricated from two commercially available, highly conductive polymer formulations based on poly (3,4-ethylendioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) was investigated. In order to enhance the electrical conductivity, the high-boiling solvent dimethyl sulfoxide (DMSO) was added. By changing the content of DMSO the electrical conductivity was increased by a factor of two without changing the Seebeck coefficient or the thermal conductivity. We achieved ZT = 9.2 × 10⁻³ at room temperature upon the addition of 5 vol.% DMSO to the PEDOT:PSS formulation.     

Boosting Performance of Non‐Fullerene Organic Solar Cells by 2D g‐C3N4 Doped PEDOT:PSS

The power‐conversion efficiency (PCE) of single‐junction organic solar cells (OSCs) has exceeded 16% thanks to the development of non‐fullerene acceptor materials and morphological optimization of active layer. In addition, interfacial engineering always plays a crucial role in further improving the performance of OSCs based on a well‐established active‐layer system. Doping of graphitic carbon nitride (g‐C₃N₄) into poly(3,4‐ethylene‐dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) as a hole transport layer (HTL) for PM6:Y6‐based OSCs is reported, boosting the PCE to almost 16.4%. After being added into the PEDOT:PSS, the g‐C₃N₄ as a Bronsted base can be protonated, weakening the shield effect of insulating PSS on conductive PEDOT, which enables exposures of more PEDOT chains on the surface of PEDOT:PSS core‐shell structure, and thus increasing the conductivity. Therefore, at the interface between g‐C₃N₄ doped HTL and PM6:Y6 layer, the charge transport is improved and the charge recombination is suppressed, leading to the increases of fill factor and short‐circuit current density of devices. This work demonstrates that doping g‐C₃N₄ into PEDOT:PSS is an efficient strategy to increase the conductivity of HTL, resulting in higher OSC performance.     

Design of Multilayered Nanostructures and Donor–Acceptor Interfaces in Solution‐Processed Thin‐Film Organic Solar Cells

Multilayered polymer thin‐film solar cells have been fabricated by wet processes such as spin‐coating and layer‐by‐layer deposition. Hole‐ and electron‐transporting layers were prepared by spin‐coating with poly(3,4‐ethylenedioxythiophene) oxidized with poly(4‐styrenesulfonate) (PEDOT:PSS) and fullerene (C₆₀), respectively. The light‐harvesting layer of poly‐(p‐phenylenevinylene) (PPV) was fabricated by layer‐by‐layer deposition of the PPV precursor cation and poly(sodium 4‐styrenesulfonate) (PSS). The layer‐by‐layer technique enables us to control the layer thickness with nanometer precision and select the interfacial material at the donor–acceptor heterojunction. Optimizing the layered nanostructures, we obtained the best‐performance device with a triple‐layered structure of PEDOT:PSS|PPV|C₆₀, where the thickness of the PPV layer was 11 nm, comparable to the diffusion length of the PPV singlet exciton. The external quantum efficiency spectrum was maximum (ca. 20%) around the absorption peak of PPV and the internal quantum efficiency was estimated to be as high as ca. 50% from a saturated photocurrent at a reverse bias of ?3 V. The power conversion efficiency of the triple‐layer solar cell was 0.26% under AM1.5G simulated solar illumination with 100 mW cm^?2 in air.     

Modification effect of hole injection layer on efficiency performance of wet-processed blue organic light emitting diodes

We examined the performance of solution-processed organic light emitting diodes (OLEDs) by modifying the hole injection layer (HIL), poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT: PSS). Atomic force microscopy (AFM) showed morphological changes with surface roughness (R_RMS) of 1.47, 1.73, and 1.37 nm for pristine PEDOT: PSS, PEDOT: PSS modified with a 40 v% deionized water and with a 30 v% acetone, respectively. The surface hydrophobicity of the acetone modified PEDOT:PSS HIL layer was decreased by 34% as comparing with the water modified counterpart. Electrical conductivity was increased to two orders of magnitude for the water and acetone modified PEDOT:PSS as compared to pristine. We observed a low refractive index and high transmittance for the modified HILs. We fabricated and explored electroluminescent properties of bis[2-(4,6-difluorophenyl)pyridinato-C2,N](picolinato)iridium(III) (FIrpic) based sky blue device by utilizing HIL with and without modification. The changes in electrical conductivity, surface roughness, refractive index, and transmittance of the modified HILs strongly influenced the performance of devices. By utilizing a 30% acetone modified HIL, the power efficiency was increased from 14.2 to 24.2 lm/W, an increment of 70% and the EQE from 8.5 to 13.1% at 100 cd/m², an increment of 54%. The maximum luminance also increased from 11,780 to 18,190 cd/m². The findings revealed herein would be helpful in designing and fabricating high efficiency solution processed OLEDs.     

Comparison of dimethyl sulfoxide treated highly conductive poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) electrodes for use in indium tin oxide-free organic electronic photovoltaic devices

Indium tin oxide (ITO)-free organic photovoltaic (OPV) devices were fabricated using highly conductive poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as the transparent conductive electrode (TCE). The intrinsic conductivity of the PEDOT:PSS films was improved by two different dimethyl sulfoxide (DMSO) treatments – (i) DMSO was added directly to the PEDOT:PSS solution (PEDOT:PSS_ADD) and (ii) a pre-formed PEDOT:PSS film was immersed in DMSO (PEDOT:PSS_IMM). X-ray photoelectron spectroscopy (XPS) and conductive atomic force microscopy (CAFM) studies showed a large amount of PSS was removed from the PEDOT:PSS_IMM electrode surface. OPV devices based on a poly(3-hexylthiophene):[6,6]-phenyl-C₆₁-butyric acid methyl ester (P3HT:PCBM) bulk hetrojunction showed that the PEDOT:PSS_IMM electrode out-performed the PEDOT:PSS_ADD electrode, primarily due to an increase in short circuit current density from 6.62 mA cm⁻² to 7.15 mA cm⁻². The results highlight the importance of optimising the treatment of PEDOT:PSS electrodes and demonstrate their potential as an alternative TCE for rapid processing and low-cost OPV and other organic electronic devices.     

Modified physico–chemical properties and supercapacitive performance via DMSO inducement to PEDOT:PSS active layer

Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) was treated with dimethyl sulfoxide (DMSO) in order to modify it physico–chemical properties in an effort to improve its electrochemical performance. In this study, the conductivity of PEDOT:PSS was controlled through post-solvent treatment in DMSO for various dipping times. The maximum conductivity of the DMSO-treated PEDOT:PSS electrode was ∼1890 S cm⁻¹. The electrical conductivity, PEDOT to PSS ratio, chemical compositions, wettability, and surface roughness are correlated and suitably explained. The supercapacitive performance of the DMSO-treated PEDOT:PSS electrodes was studied in 1 M H₂SO₄ within an optimized potential window of 0 to −0.6 V versus Ag/AgCl. The maximum specific capacitance of the PEDOT:PSS electrode treated in DMSO for 60 min was found to be ∼153 F g⁻¹ at a 1 mA cm⁻² discharge current density (∼145 F g⁻¹ at a 10 mV s⁻¹ scan rate), along with an energy density of 93 W h kg⁻¹ and a power density of 4.6 kW kg⁻¹.     

Wide range thickness effect of hole-collecting buffer layers for polymer:fullerene solar cells

Here we report the wide range thickness effect of hole-collecting buffer layers (poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)) on the performance of polymer:fullerene solar cells with blend films of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C₆₁-butyric acid methyl ester (PC₆₁BM). The thickness of the PEDOT:PSS layers was controlled from 3 nm to 625 nm, followed by characterizations such as optical transmittance, electrical resistances in the in-plane and out-of-plane directions, work functions, contact angles, and device performances. Results showed that the optical transmittance was gradually decreased with the PEDOT:PSS thickness but a maximum value was measured for other properties in the thickness range of 10–30 nm. The device performance was noticeably improved with only 3 nm-thick PEDOT:PSS layer, while it was almost similar in the thickness range of 30–225 nm in the presence of gradual decrease in the surface roughness. The similar device performance between 30 nm and 225 nm has been assigned to the compensation effect between the reduced electrical resistance (increased conductivity) and the decreased optical transmittance as the thickness of the PEDOT:PSS layer increased.     

Effects of tetramethylene sulfone solvent additives on conductivity of PEDOT:PSS film and performance of polymer photovoltaic cells

A solvent additive in PEDOT:PSS solution is one of many methods to improve the conductivity of the poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films. We explore a new type of the solvent additive, namely tetramethylene sulfone (TMS), for the fabrication of the PEDOT:PSS conductive layer in the ITO/PEDOT:PSS/P3HT:PCBM/TiO_x/Al polymer photovoltaic cells, in comparison to a more common dimethyl sulfoxide (DMSO) solvent additive. At optimal conditions, the TMS additive at 10 wt.% has been found to enhance the conductivity of pristine PEDOT:PSS films from 0.04 S/cm up to approximately 189 S/cm, compared with the highest conductivity for the case of the DMSO additive at 15 wt.% of 117 S/cm. Possible mechanisms of this conductivity enhancement, relating to the polymer conformation and the film morphology, have been investigated by Raman spectroscopy, X-ray diffraction, atomic force microscopy, and transmission electron microscopy. The performance of the polymer photovoltaic cells fabricated with the solvent additives PEDOT:PSS films follows a similar trend to the conductivity of the films as a function of the additive concentration. The additives mainly lead to greater short circuit current density (J_sc) of the photovoltaic cells. The highest power conversion efficiency (PCE) of 2.24% of the device has been obtained with the 10 wt.% TMS additive of, compared to the PCE of 1.48% for the standard device without solvent additive.     

Conjugated Small Molecule for Efficient Hole Transport in High‐Performance p‐i‐n Type Perovskite Solar Cells

The π‐conjugated organic small molecule 4,4′‐cyclohexylidenebis[N,N‐bis(4‐methylphenyl) benzenamine] (TAPC) has been explored as an efficient hole transport material to replace poly(3,4‐ethylenedio‐xythiophene):poly(styrenesulfonate) (PEDOT:PSS) in the preparation of p‐i‐n type CH₃NH₃PbI₃ perovskite solar cells. Smooth, uniform, and hydrophobic TAPC hole transport layers can be facilely deposited through solution casting without the need for any dopants. The power conversion efficiency of perovskite solar cells shows very weak TAPC layer thickness dependence across the range from 5 to 90 nm. Thermal annealing enables improved hole conductivity and efficient charge transport through an increase in TAPC crystallinity. The perovskite photoactive layer cast onto thermally annealed TAPC displays large grains and low residual PbI₂, leading to a high charge recombination resistance. After optimization, a stabilized power conversion efficiency of 18.80% is achieved with marginal hysteresis, much higher than the value of 12.90% achieved using PEDOT:PSS. The TAPC‐based devices also demonstrate superior stability compared with the PEDOT:PSS‐based devices when stored in ambient circumstances, with a relatively high humidity ranging from 50 to 85%.     

Efficient and Stable Perovskite Solar Cells via Dual Functionalization of Dopamine Semiquinone Radical with Improved Trap Passivation Capabilities

Highly efficient planar heterojunction perovskite solar cells (PVSCs) with dopamine (DA) semiquinone radical modified poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) (DA‐PEDOT:PSS) as a hole transporting layer (HTL) were fabricated. A combination of characterization techniques were employed to investigate the effects of DA doping on the electron donating capability of DA‐PEDOT:PSS, perovskite film quality and charge recombination kinetics in the solar cells. Our study shows that DA doping endows the DA‐PEDOT:PSS‐modified PVSCs with a higher radical content and greater perovskite to HTL charge extraction capability. In addition, the DA doping also improves work function of the HTL, increases perovskite film crystallinity, and the amino and hydroxyl groups in DA can interact with the undercoordinated Pb atoms on the perovskite crystal, reducing charge‐recombination rate and increasing charge‐extraction efficiency. Therefore, the DA‐PEDOT:PSS‐modified solar cells outperform those based on PEDOT:PSS, increasing open‐circuit voltage (V _oc) and power conversion efficiency (PCE) to 1.08 V and 18.5%, respectively. Even more importantly, the efficiency of the unencapsulated DA‐PEDOT:PSS‐based PVSCs are well retained with only 20% PCE loss after exposure to air for 250 hours. These in‐depth insights into structure and performance provide clear and novel guidelines for the design of effective HTLs to facilitate the practical application of inverted planar heterojunction PVSCs.     

A Simple Cu(II) Polyelectrolyte as a Method to Increase the Work Function of Electrodes and Form Effective p-Type Contacts in Perovskite Solar Cells

One effective strategy to improve the performance of perovskite solar cells (PSCs) is to develop new hole transport layers (HTLs). In this work, a simple polyelectrolyte HTL, copper (II) poly(styrene sulfonate) (Cu:PSS), which comprises easily reduced Cu²⁺ counter-ions with an anionic PSS polyelectrolyte backbone is investigated. Photoelectron spectroscopy reveals an increase in the work function of the anode and upward band bending effect upon incorporation of Cu:PSS in PSC devices. Cu:PSS shows a synergistic effect when mixed with polyethylenedioxythiophene: polystyrenesulfonate (PEDOT:PSS) in various proportions and results in a decrease in the acidity of PEDOT:PSS as well as reduced hysteresis in completed devices. Cu:PSS functions effectively as a HTL in PSCs, with device parameters comparable to PEDOT:PSS, while mixtures of Cu:PSS with PEDOT:PSS shows greatly improved performance compared to PEDOT:PSS alone. Optimized devices incorporating Cu:PSS/PEDOT:PSS mixtures show an improvement in efficiency from 14.35 to 19.44% using a simple CH₃NH₃PbI₃ active layer in an inverted (P-I-N) geometry, which is one of the highest values yet reported for this type of device. It is expected that this type of HTL can be employed to create p-type contacts and improve performance in other types of semiconducting devices as well.     

The enhancement of electrical and optical properties of PEDOT:PSS using one-step dynamic etching for flexible application

The conductivity enhancement of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) by dynamic etching process was investigated to introduce the outstanding and simplest method for soft electronics. Four different samples which were pristine PEDOT:PSS, PEDOT:PSS doped with 5 wt.% DMSO, PEDOT:PSS with dipping process, and PEDOT:PSS with dynamic etching process were prepared to compare the properties such as conductivity, morphology, relative atomic percentage, and topography. All samples were characterized by four point probe, current atomic force microscopy (C-AFM), X-ray photoelectron spectroscopy (XPS), and UV–visible spectroscopy. The conductivity of the sample with dynamic etching process showed the highest value as 1299 S/cm among four samples. We proved that the dynamic etching process is superior to remove PSS phase from PEDOT:PSS film, to flow strong current through entire surface of PEDOT:PSS, and to show the smoothest surface (RMS 2.28 nm). XPS analysis was conducted for accurate chemical and structural surface environments of four samples and the relative atomic percentage of PEDOT in the sample with dynamic etching was the highest as 29.5%. The device performance of the sample with the dynamic etching process was outstanding as 10.31 mA/cm² of J_sc, 0.75 eV of V_oc, 0.46 of FF, and 3.53% of PCE. All properties and the device performance for PEDOT:PSS film by dynamic etching process were the most excellent among the samples.     

Stable organic photovoltaic with PEDOT:PSS and MoOX mixture anode interfacial layer without encapsulation

Herein, we report about an efficient and stable organic photovoltaic that uses a poly(3,4-ethylenedioxythiophene):poly(styrene-sulfonate) (PEDOT:PSS) and molybdenum oxide (MoO_X) mixture for the anode interfacial layer, and that can reach 4.43% power conversion efficiency (PCE) under AM1.5 conditions. Utilizing PEDOT:PSS:MoO_X (1:1), the shelf lifetime of poly(3-hexylthiophene) (P3HT), and indene-C₆₀ bisadduct (ICBA)-based solar cells without encapsulation, can be realized with only a 25% deterioration after 672 h of storage in air. Furthermore, we compare the photovoltaic performance of the P3HT:ICBA-based organic photovoltaic with PEDOT:PSS, and PEDOT:PSS:MoO_X, in which PEDOT:PSS:MoO_X has outperformed the others. In addition, the water vapor transmission rate of PEDOT:PSS:MoO_X is 0.17 gm/(m² day), which is much less than that of PEDOT:PSS.     

Simultaneous enhancement of the efficiency and stability of organic solar cells using PEDOT:PSS grafted with a PEGME buffer layer

We report a simple processing method to simultaneously improve the efficiency and stability of organic solar cells (OSCs). Poly(4-styrene sulfonate)-doped poly(3,4-ethylenedioxy-thiophene (PEDOT:PSS), widely used as hole transport layer (HTL) in OSCs, tends to accelerate the degradation of devices because of its hygroscopic and acidic properties. In this regard, we have modified PEDOT:PSS to reduce its hygroscopic and acidic properties through a condensation reaction between PEDOT:PSS and poly(ethylene glycol) methyl ether (PEGME) in order to improve the efficiency and stability of OSCs. As a result, the power conversion efficiency (PCE) increased by 21%, from 2.57% up to 3.11%. A better energy level alignment by the reduced work function of the modified PEDOT:PSS with a highest occupied molecular orbital (HOMO) level of poly(3-hexylthiophene-2,5-diyl) (P3HT) is considered the origin of the improved the efficiency. The half-life of OSCs with PEDOT:PSS modified with PEGME buffer layer also increased up to 3.5 times compared to that of devices with pristine PEDOT:PSS buffer layer.     

Efficient Polymer Solar Cells Based on Poly(3‐hexylthiophene):Indene‐C70 Bisadduct with a MoO3 Buffer Layer

Polymer solar cells (PSCs) with poly(3‐hexylthiophene) (P3HT) as a donor, an indene‐C₇₀ bisadduct (IC₇₀BA) as an acceptor, a layer of indium tin oxide modified by MoO₃ as a positive electrode, and Ca/Al as a negative electrode are presented. The photovoltaic performance of the PSCs was optimized by controlling spin‐coating time (solvent annealing time) and thermal annealing, and the effect of the spin‐coating times on absorption spectra, X‐ray diffraction patterns, and transmission electron microscopy images of P3HT/IC₇₀BA blend films were systematically investigated. Optimized PSCs were obtained from P3HT/IC₇₀BA (1:1, w/w), which exhibited a high power conversion efficiency of 6.68%. The excellent performance of the PSCs is attributed to the higher crystallinity of P3HT and better a donor–acceptor interpenetrating network of the active layer prepared under the optimized conditions. In addition, PSCs with a poly(3,4‐ethylenedioxy‐thiophene):poly(styrenesulfonate) (PEDOT:PSS) buffer layer under the same optimized conditions showed a PCE of 6.20%. The results indicate that the MoO₃ buffer layer in the PSCs based on P3HT/IC₇₀BA is superior to that of the PEDOT:PSS buffer layer, not only showing a higher device stability but also resulting in a better photovoltaic performance of the PSCs.     

Aging process of PEDOT:PSS dispersion and robust recovery of aged PEDOT:PSS as a hole transport layer for organic solar cells

Conducting p-type polymer of poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) has been widely used for organic optoelectronics, particularly as a hole transport layer for organic solar cells. While the aged PEDOT:PSS dispersion impacts device performance, the aging of PEDOT:PSS dispersion have not been well investigated. Moreover, the recovery process of aged (two-year-old) PEDOT:PSS dispersion has not been demonstrated yet. Herein, it is found that aqueous PEDOT:PSS dispersion undergoes extensive phase separation during the aging process, resulting in both nanoscale and macroscale hydrophobic PEDOT-rich agglomerates. When the aged PEDOT:PSS thin film is integrated into P3HT:PCBM organic solar cells, the PEDOT-rich agglomerates trap the photogenerated holes at the PEDOT:PSS/P3HT interface, resulting in poor extraction efficiency in organic solar cells. To recover a hole transport functionality from aged PEDOT:PSS, three different solvents such as isopropyl alcohol (C₃H₇OH), ethanol (C₂H₅OH) and methanol (CH₃OH) are investigated. Among them, it is found that isopropyl alcohol (IPA) yielded very uniform PEDOT:PSS thin film layer. This is because hydrophobic functional groups of IPA solvent facilitated the preferential solvation of phase separated hydrophobic PEDOT-rich agglomerates. However, when non-optimal concentration of IPA solvents was added into the aged PEDOT:PSS dispersion, the size of PEDOT-rich agglomerates was adversely enlarged. When organic solar cells were fabricated using more than a two-year-old PEDOT:PSS that was treated with IPA solvent, the resulting device performance of organic solar cells was fully recovered and became comparable or better than that of organic solar cells fabricated with fresh PEDOT:PSS.     

Optimization of electrohydrodynamic-printed organic electrodes for bottom-contact organic thin film transistors

In this study, we investigate the optimization of printed (3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) as source/drain electrodes for organic thin film transistors (OTFTs) through electrohydrodynamic (EHD) printing process. The EHD-printed PEDOT:PSS electrodes should fulfill the prerequisites of not only high conductivity but also optimum surface tension for successful jetting. The conductivity of PEDOT:PSS was dramatically enhanced from 0.07 to 352 S/cm by the addition of dimethylsulfoxide (DMSO). To use the DMSO-treated PEDOT:PSS solution in the EHD printing process, its surface tension was optimized by the addition of surfactant (Triton X-100), which was found to enable various jetting modes. In the stable cone-jet mode, the patterning of the modified PEDOT:PSS solution was realized on the surface-functionalized SiO₂ substrates; the printed line widths were in the range 384 to 81 μm with a line resistance of 8.3 × 10³ Ω/mm. In addition, pentacene-based OTFTs employing the EHD-printed PEDOT:PSS as source and drain electrodes were found to exhibit electrical performances superior to an equivalent vacuum-deposited Au-based device.     

Achieving a Record Fill Factor for Silicon–Organic Hybrid Heterojunction Solar Cells by Using a Full‐Area Metal Polymer Nanocomposite Top Electrode

Carrier collection in conventional n‐type Si (n‐Si)/organic hybrid heterojunction solar cells (HHSCs) is mainly limited by the nonoptimized top grid‐electrode and inadequate work function (WF) of the PH1000‐type poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS). Here, a novel modified metal polymer nanocomposite top electrode (M‐MPNTE) is designed to achieve a full‐area carrier collection in n‐Si/PEDOT:PSS HHSCs. The carrier collection in both lateral and vertical directions is significantly improved by the introduction of an ultrathin Au/MoO_x modified layer between 6 nm ultrathin Ag film and AI4083‐type PEDOT:PSS layer. In addition, the carrier separation is boosted by the enhanced built‐in potential owing to a high WF of M‐MPNTE, which also suppresses the carrier recombination at the surface of n‐Si. Due to these collaborative improvements, a record fill factor of 80.21% is obtained, which is even comparable to the best value of the traditional Si‐based solar cells. With the addition of a MoO_x antireflective coating layer on top of M‐MPNTE, the short‐circuit current density and open‐circuit voltage are finally increased to 23.13 mA cm^?2 and 621.07 mV, respectively, yielding a power conversion efficiency of 10.82%. The finding suggests a novel strategy for the development of highly efficient HHSCs with ideal carrier transport mechanism.     

Metal salt modified PEDOT:PSS as anode buffer layer and its effect on power conversion efficiency of organic solar cells

The effects of metal chlorides such as LiCl, NaCl, CdCl₂ and CuCl₂ on optical transmittance, electrical conductivity as well as morphology of PEDOT:PSS films have been investigated. Transmittance spectra of spun PEDOT:PSS layers were improved by more than 6% to a maximum of 94% in LiCl doped PEDOT:PSS film. The surface of the PEDOT:PSS films has exhibited higher roughness associated with an increase in the electrical conductivity after doping with metal salts. The improvement in the physical properties of PEDOT:PSS as the hole transport layer proved to be key factors towards enhancing the P3HT:PCBM bulk heterojunction (BHJ) solar cells. These improvements include significantly improved power conversion efficiency with values as high as 6.82% associated with high fill factor (61%) and larger short circuit current density (∼18 mA cm⁻²).