共查询到20条相似文献,搜索用时 140 毫秒
1.
标准贯入击数N值的修正是一个复杂急待解决的问题。在推荐以N=N’×(1一l/200)公式进行杆长能量传递修正后,进而推荐以弯曲修正系数λ进行N值的二次杆长修正。并根据华东沿海地区大量实测数据回归统计,得到地区性λ值表。 相似文献
2.
3.
4.
5.
本文从理论和实践两方面论证了对Pearson-Waddington公式的修正,其值不是定向常量的,即修正不总是正的或负的,也不是常数,它视具体条件而异。导出了新的统一修正式,它可以囊括已经提出的所有修正式。根据大量实测数据给出了修正项对N关系的估值,以供实际计算使用。 相似文献
6.
7.
本文简要介绍了标准贯入试验在大庆油田工程勘察中的应用情况。并对所使用的探杆类型,根据标准贯入试验资料进行了统计分析后,提出探杆需要修正意见及修正系数关系式。同时,对标准贯入试验能在油田工程勘察中更好地应用及探杆标准化问题提出建议。 相似文献
8.
介绍了检定高频电压表频响误差的工作标准 ,该标准采用定点修正的方法 ,具有小型、便携、准确度高等特点。 相似文献
9.
岩体爆破是一个极其复杂的物理过程,应用数值模型研究岩体爆破响应的关键在于能否准确地描述岩体在不同应力状态下的力学行为。基于应用标准RHT模型模拟岩体爆破破碎过程存在的缺陷,对RHT模型进行改进,提出了双线性拉伸软化模型,在残余强度面方程中引入罗德角因子,修正了应变率增强因子和拉-压子午比的计算公式。将修正后的RHT模型植入SHALE程序中,并通过不同应力路径下的数值试验检验了修正RHT模型性能。应用修正RHT模型和标准RHT模型分别对爆破漏斗试验进行数值模拟。计算结果表明,修正RHT模型在自由面处形成的爆破漏斗半径更接近于现场试验的实测结果,验证了修正RHT模型的合理性和准确性,说明该模型在岩体爆破响应数值模拟中具有一定的参考价值。 相似文献
10.
11.
标准贯入试验中杆长校正的一点看法 总被引:1,自引:0,他引:1
本文根据《岩土工程勘察规范》(GB50021—94)关于标准贯入试验锤击数(下称标贯击数)杆长校正问题的表述,对标贯锤击数是否应作杆长校正提出了作者的看法,认为在目前情况下,对标贯击数值进行杆长校正是必要的. 相似文献
12.
一种用标贯击数直接确定粉土,砂土压缩模量的方法 总被引:3,自引:0,他引:3
本文通过对现行确定粉土、砂土压缩模量方法的利弊进行分析.提出一种使用标贯击数(标准值)直接确定粉土、砂土压缩模量Es1-2(标准值)的方法,并对其适用性结合已有经验公式和具体工程进行评价.具有一定的推广价值。 相似文献
13.
The authors report and discuss the experimental results on an air drill hammer with an elastic valve installed in the backstroke exhaust line for mechanical closing. It is approved that such air hammer is capable to ensure the wanted blow capacity at the fixed blow energy by varying blow frequency through adjustment of cross section choke coupling the backstroke and front stoke chambers of the hammer. With the larger cross section of the choke coupling, the maximum blow frequency is achieved and remains the same later on. 相似文献
14.
标准贯入试验目前已广泛应用于各类工程勘察施工,然而在冲积平原等湖泊、河流和沿海地区常出现标贯击数确定的岩土物理、力学性质与土工试验和静力触探结果不匹配的情况.本文结合长江左岸Ⅰ级阶地上的具体工程案例,同时对标贯试验、土工试验和静力触探的试验结果进行对比分析,而后对标贯试验结果进行杆长修正,使三者确定的岩土性能指标更匹配... 相似文献
15.
16.
The authors describe and discuss experimental investigation of the effect exerted by blow frequency and additional static force on penetration rate of a pipe under vibration-percussion by a pneumatic hammer with using a measuring and recording instrumentation developed at the Institute of Mining, Siberian Branch, Russian Academy of Sciences. The penetration velocity ranges are found for the real blow frequencies of the test pneumatic hammer equipped with additional static load. Determination of static force sufficient to press the pipe in soil in hammer-free regime is reported. 相似文献
17.
18.
ZYLDⅡ型自动压滤机新增设了电流传感器、电流采集模块和液晶触摸屏 ,实现了脱水工艺参数———进料时间、压榨时间、吹气时间可以随工况条件变化随时调整 ;滤板压紧程度由主电机电流控制 ,主电机电流可预先设置在触摸屏上 ,并且可根据隔膜新、旧情况设定合适的电流 相似文献
19.
Design of an air drill hammer with the smooth adjustment of the percussion frequency at the constant blow energy is considered. The proposed and analyzed modifications of air distribution system are based on using a mechanically closing elastic valve. The test data on experimental prototypes of the air drill hammer with the external distributing elements that set blow frequency are presented. The frequency adjustment ranges are determined. 相似文献