共查询到20条相似文献,搜索用时 743 毫秒
1.
法兰接头在高温环境中工作时,接头各个部件的蠕变松弛会加剧,然而在法兰接头的研究中,大多没有考虑垫片的蠕变松弛。以金属石墨缠绕垫片为例,在不同温度及不同初始密封比压情况下进行蠕变松弛性能试验;将试验结果进行拟合得到垫片蠕变松弛性能计算公式,将其代入法兰接头变形协调方程中,计算得到接头蠕变2年的螺栓力随时间的变化情况。使用ANSYS软件建立法兰接头有限元模型,并计算不同部件蠕变2年所造成的螺栓力的松弛情况。理论计算结果与有限元计算结果相近,表明建立的理论模型可用于接头螺栓力松弛的评估。研究结果表明:初始密封比压相同时,温度越大则垫片的蠕变量越大,温度相同时,初始密封比压越大则垫片的蠕变量越大;垫片蠕变对法兰接头有显著影响,在一些情况下仅垫片蠕变就能使螺栓力下降40%,因此垫片蠕变对法兰接头的影响不能忽略。 相似文献
2.
长期工作在高温下的螺栓法兰接头,由于密封垫片和螺栓的蠕变松弛,使得垫片上的残余应力逐渐减小,法兰接头的密封可靠性逐渐降低,并最终导致泄漏失效。在考虑垫片和螺栓蠕变的基础上,对法兰连接系统进行变形协调分析,建立了高温下法兰接头的变形协调方程,进而导出了泄漏率的极限方程;通过与法兰强度、螺栓强度的极限方程相结合,得出了利用Monte Carlo法计算高温螺栓法兰接头可靠度的方法,并给出了计算实例。 相似文献
3.
对SA213-T92钢焊管在600~750℃进行了不同时间的退火处理,对退火前后的残余应力进行了测定,对应力的热松弛行为进行了分析,根据高温松弛动力学曲线计算得到了松弛激活能。结果表明:退火前焊管接头表面的纵向残余应力高于横向的,两者分布规律相似,离焊缝越远,残余拉应力越小;不同温度退火后焊管接头表面的残余应力比退火前均有降低,随着退火温度的升高,残余拉应力逐渐降低;根据不同退火温度下焊缝残余应力的热松弛动力学曲线,求得蠕变等效方程中的系数B为5.07×104,应力指数n为4.4及应力松弛激活能Q为242kJ·mol-1。 相似文献
4.
5.
6.
7.
8.
以某液氨运输罐车为研究对象,分析罐车液相法兰密封性能的影响因素,指出垫片失效变形、介质内压载荷变化和环境温度变化是影响法兰密封系统的主要因素。建立液相法兰的有限元模型,分析预紧工况下垫片的失效变形、内压载荷和环境温度对螺栓法兰接头密封性能的影响。模拟结果表明:液相法兰紧急切断阀阀根的内芯平面与法兰盘密封垫片之间存在凹陷区域,造成垫片的密封面积减少20.9%,降低法兰接头的密封性能;介质内压载荷的波动对系统密封性能影响很小;温度变化对残余压应力值的影响较大,决定密封条件的最小压力值随温度降低而降低,从而影响法兰的密封性能。 相似文献
9.
10.
为了研究火箭发动机法兰系统载荷-变形随时间的变化,将其作为一个整体,考虑系统中各元件的蠕变-松弛作用,提出了在预紧和操作情况下,计算法兰系统载荷-变形的新方法;算例计算结果表明:在预紧情况下的很长时间段内,螺栓应力和O形圈应力下降得非常缓慢;在操作情况下的开始时间段内,其下降较快,随着时间的推移,下降速率逐渐减慢。在预紧情况下,法兰系统各元件材料的蠕变-松弛性能对O形圈应力的影响较小;在操作情况下,这种影响则较大。若考虑螺栓的蠕变-松弛,则随螺栓蠕变-松弛系数的增大,螺栓应力和O形圈应力随时间下降得较多。 相似文献
11.
In a recent paper, the Ritz method with simple algebraic polynomials as trial functions was used to obtain an eigenvalue equation for the free vibration of a class of homogeneous solids with cavities. The method presented is here extended to the study of a class of non-homogeneous solids, in which each solid is composed of a number of isotropic layers with different material properties. The Cartesian coordinate system is used to describe the geometry of the solid which is modelled by means of a segment bounded by the yz, zx and xy orthogonal coordinate planes and by two curved surfaces which are defined by fairly general polynomial expressions in the coordinates x, y and z. The surface representing the interface between two material layers in the solid is also described by a polynomial expression in the coordinates x, y and z. In order to demonstrate the accuracy of the approach, natural frequencies are given for both a two- and three-layered spherical shell and for a homogeneous hollow cylinder, as computed using the present approach, and are compared with those obtained using an exact solution. Results are then given for a number of two- and three-layered cylinders and, to demonstrate the versatility of the approach, natural frequencies are given for a five-layered cantilevered beam with a central circular hole as well as for a number of composite solids of more general shape. 相似文献
12.
13.
通过分析膨胀套在实际使用产生滑移受阻现象、卡死现象原因的实质,并在分析产生问题原因的基础上提出了改进措施即:增加导向机构。 相似文献
14.
15.
设计了磨粉机快辊轴承座的加工工艺和具体的工装夹具.利用卧式加工中心加工磨粉机快辊轴承座,辅以能够高效快速夹紧的夹具,既可以保证加工精度,又能够提高加工效率. 相似文献
16.
一种涡旋压缩机径向随变机构的设计 总被引:1,自引:0,他引:1
详细介绍了运用随变原理设计的一种新型径向密封机构的结构特点,工作原理及主要参数的确定方法,该机构可补偿由于涡旋体加工精度不高而造成的功率损失,适用于涡旋压缩机的批量生产。 相似文献
17.
本文以某些积算和双笔记录仪产品为例说明由于仪表功能设计的不合理或选型不当,影响了仪表的正常使用,制造厂和用户应关注这类问题。 相似文献
18.
V. P. Dragunov E. G. Kostsov 《Optoelectronics, Instrumentation and Data Processing》2009,45(3):234-242
Specific features of operation of one- and two-capacitor microelectromechanical converters (MEMC) of energy of mechanical microscopic vibrations into electric energy with a modulated electrode-gap magnitude and with allowance for the mutual influence of electrical and elastic forces are analyzed, and the characteristics of these two devices are compared. The main factors restricting the increase in MEMC power are demonstrated to be the effects of “collapsing” and the condition of conservation of positive rigidity of the system. Expressions for estimating the limiting MEMC parameters are derived. The possibility of electrical energy generation in the presence of “real“ sources of wide-spectrum microscopic vibrations is considered. 相似文献
19.
针对目前市场对工业设计人才的需求,本文论述了我校在工业设计教育方面的改革措施,着重介绍了我校工业设计教育在软件和硬件方面所进行的一系列的改革。 相似文献