Preparation and characterization of bismaleimide (N,N′‐bismaleimido‐4,4′‐diphenyl methane)–vinyl ester oligomer–modified unsaturated polyester interpenetrating matrices for advanced composites

Interpenetrating networks of varying percentages of bismaleimide (BMI) in vinyl ester oligomer (VEO) modified unsaturated polyester (UP) matrices have been developed. Vinyl ester oligomer was prepared by reacting commercially available epoxy resin GY 250 (Ciba‐Geigy) and acrylic acid, and used as a toughening agent for unsaturated polyester resin. Unsaturated polyesters modified with 10, 20, and 30 wt % vinyl ester oligomer were made. The VEO toughened unsaturated polyester matrix systems, further modified with 5, 10, and 15 wt % bismaleimide (BMI). BMI–VEO–UP matrices were characterized using differential scanning calorimetry, thermogravimetric analysis, and heat deflection temperature analysis. The matrices, in the form of castings, were characterized for their mechanical properties according to ASTM methods: tensile strength, flexural strength, and unnotched Izod impact test. Data obtained from mechanical studies and thermal characterization indicate that the introduction of VEO and BMI into unsaturated polyester resin improves thermomechanical properties according to their percentage concentration. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2502–2508, 2002     

Non‐isothermal degradation kinetics of N,N′‐bismaleimide‐4,4′‐diphenylmethane/barbituric acid based polymers in the presence of hydroquinone

The non‐isothermal degradation kinetics of the cured polymer samples of N,N′‐bismaleimide‐4,4′‐diphenylmethane/barbituric acid [BMI/BTA = 2/1 (mol/mol)] based polymers in the presence of hydroquinone (HQ) and native BMI/BTA was investigated by the thermogravimetric (TG) technique. By adding 5 wt % HQ into the BMI/BTA polymerization, the activation energy (E_a) of the thermal degradation process increased significantly in comparison with native BMI/BTA. Thus, the thermal stability of the cured polymer sample in the presence of HQ was greatly improved. The thermal degradation process exhibits three distinct stages. The key kinetic parameters associated with these stages were attained via the model‐fitting method. For the sample of native BMI/BTA, the thermal degradation process was primarily controlled by nucleation, followed by the multi‐decay law in the first stage. In contrast, the reaction order model adequately described the thermal degradation kinetics in the second stage. As to the last stage, the complex processes were described satisfactorily by the best‐fitted reaction model. For the sample of BMI/BTA/5 wt % HQ, the degradation process was controlled by the nucleation mechanism, followed by the multi‐molecular decay law in the first stage. In contrast, the second stage was controlled by the mixed mode of the competitive reaction order mechanism and 3‐D diffusion mechanism. In the third stage, the complex processes were also adequately described by the best‐fitted reaction model. All the experimental results illustrated that incorporation of 5 wt % HQ into the BMI/BTA based polymer resulted in the best thermal stability. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1923–1930, 2013     

Synthesis and characterization of new optically active poly(amide‐imide‐urethane) thermoplastic elastomers,derived from 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L‐leucine‐p‐aminobenzoic acid) and PEG‐MDI

A new class of optically active poly(amide‐imide‐urethane) was synthesized via two‐step reactions. In the first step, 4,4′‐methylene‐bis(4‐phenylisocyanate) (MDI) reacts with several poly(ethylene glycols) (PEGs) such as PEG‐400, PEG‐600, PEG‐2000, PEG‐4000, and PEG‐6000 to produce the soft segment parts. On the other hand, 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L ‐leucine‐p‐amidobenzoic acid) (2) was prepared from the reaction of 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L ‐leucine) diacid chloride with p‐aminobenzoic acid to produce hard segment part. The chain extension of the above soft segment with the amide‐imide 2 is the second step to give a homologue series of poly(amide‐imide‐urethanes). The resulting polymers with moderate inherent viscosity of 0.29–1.38 dL/g are optically active and thermally stable. All of the above polymers were fully characterized by IR spectroscopy, elemental analyses, and specific rotation. Some structural characterization and physical properties of this new optically active poly(amide‐imide‐urethanes) are reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2288–2294, 2004     

Synthesis of soluble and thermally stable polyimides from 3,5‐diamino‐N‐(4‐(8‐quinolinoxy) phenyl) aniline and various dianhydrides

Three novel polyimides (PIs) having pendent 4‐(quinolin‐8‐yloxy) aniline group were prepared by polycondensation of a new diamine with commercially available tetracarboxylic dianhydrides, such as pyromellitic dianhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, and bicyclo[2.2.2]‐oct‐7‐ene‐2,3,5,6‐tetracarboxylic dianhydride. These PIs were characterized by FTIR, ¹H NMR, and elemental analysis; they had high yields with inherent viscosities in the range of 0.4–0.5 dl g⁻¹, and exhibited excellent solubility in many organic solvents such as N,N‐dimethyl acetamide, N,N′‐dimethyl formamide, N‐methyl pyrrolidone (NMP), dimethyl sulfoxide, and pyridine. These PIs exhibited glass transition temperatures (T_g) between 250 and 325° C. Their initial decomposition temperatures (T_i) ranged between 270 and 450°C, and 10% weight loss temperature (T₁₀) up to 500°C with 68% char yield at 600°C under nitrogen atmosphere. Transparent and hard polymer films were obtained via casting from their NMP solutions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Ambipolar and multi‐electrochromic polyimides based on N,N‐di(4‐aminophenyl)‐N′,N′‐diphenyl‐4,4′‐oxydianiline

A series of novel aromatic polyimides were synthesized from N,N‐di(4‐aminophenyl)‐N′,N′‐diphenyl‐4,4′‐oxydianiline and aromatic tetracarboxylic dianhydrides through a conventional two‐step procedure. Most of the polyimides exhibited reasonable solubility in organic solvents and could afford robust films via solution casting. The polyimides exhibited high thermal stability, with glass transition temperatures in the range 227–273 °C and 10% weight‐loss temperatures in excess of 550 °C. All the polyimide films showed ambipolar redox and multi‐electrochromic behaviors. They exhibited two reversible oxidation redox couples at 0.94–0.98 and 1.09–1.12 V versus Ag/AgCl in acetonitrile solution. A coupling reaction between the radical cations of the pendent triphenylamine units occurred during the oxidative process forming a tetraphenylbenzidine structure which resulted in an additional redox state and color change. © 2014 Society of Chemical Industry     

Preparation and properties of 4,4′‐(hexafluoroisopropylidene) diphenol cured 2,2‐bis(4‐cyanatophenyl) propane

A novel easily curing system of 2,2‐bis(4‐cyanatophenyl) propane(BACY) was prepared by employing 4,4′‐(Hexafluoroisopropylidene) Diphenol (BPAF) as modifier. The curing efficiency of BPAF was evaluated by means of differential scanning calorimetry (DSC) and Fourier translation infrared spectroscopy analysis (FTIR). It was found that the exothermic peak temperature (T_p) was 168 °C when the content of BPAF/BACY was 15/85 by weight, while the temperature of BACY was 215 °C under the same conditions when trace of cobalt(III) acetylacetonate(CoAt(III)) was added. Besides, BPAF/BACY system owned outstanding properties including excellent curing characteristics, high shear strength, remarkable dielectric properties and high thermal stability in contrast to BACY, 4,4′‐(1‐methylethylidene) bisphenol(BPA)/BACY, and nonylphenol(NoP)/BACY systems. Moreover, the properties of cured BPAF/BACY modified by different proportions of BPAF were studied in detail. It was shown that moderate BPAF was conducive to most properties of polycyanurate, and the optimal proportion of BPAF/BACY was 15/85 by weight. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44518.     

The synthesis of block copolyetherketones based on 4,4′‐dichlorodiphenylketone,phenolphthaleine, and bisphenol A and investigation of their properties

Block structured polyethers based on phenolphthaleine, 4,4′‐dichlorodiphenylketone, and bisphenol A with different degrees condensation (n = 1, 5, 10, and 20) were synthesized by means of acceptor‐catalytic polycondensation. Equaimolar quantities of chloranhydrides of iso‐ and terephthalic acids were used. Higher molecular masses were obtained from longer oligoketones with higher condensation degrees. Better molecular packing, increased thermal and mechanical properties were obtained with higher condensation degrees of oligoketones. © 2007 Wiley Periodicals, Inc. JAppl Polym Sci, 2008     

Functionalized N‐(4‐hydroxy phenyl) maleimide monomers: Kinetics of thermal polymerization and degradation using model‐free approach

N‐(4‐Hydroxy phenyl) maleimide (HPMI) is prepared and is functionalized with acryloyl, methacryloyl, allyl, propargyl, and cyanate groups. The structural and thermal characterizations of the materials are done using FTIR, NMR, DSC, and TGA. Curing and degradation kinetics are performed using Flynn–Wall–Ozawa, Vyazovkin, and Friedman methods. Activation energies (E_a) for the polymerization of the synthesized monomers varied and are dependent on the nature of the functional group present in HPMI. The propargyl functionalized monomer shows the highest E_a values whereas the methacryloyl functionalized monomer shows the lowest E_a values. In the case of thermal degradation of the polymerized materials, the apparent E_a values for acryloyl, methacryloyl and cyanate functionalized materials are slightly higher than that of poly‐HPMI (PHPMI). The thermally cured allyl and propargyl functionalized materials show a different trend and may be attributed to the complications arising due to Claisen rearrangement reaction during the thermal curing. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39935.     

Microwave‐assisted and conventional polycondensation reaction of optically active N,N′‐(4,4′‐sulphonediphthaloyl)‐bis‐L‐leucine diacid chloride with aromatic diamines

3,3′,4,4′‐Diphenylsulfonetetracarboxylic dianhydride ( 1 ) was reacted with L‐leucine ( 2 ) in acetic acid and the resulting imide‐acid ( 3 ) was obtained in high yield. The diacid chloride ( 4 ) was prepared from diacid derivative ( 3 ) by reaction with thionyl chloride. The polycondensation reaction of diacid chloride ( 4 ) with several aromatic diamines such as 4,4′‐sulfonyldianiline ( 5a ), 4,4′‐diaminodiphenyl methane ( 5b ), 4,4′‐diaminodiphenylether ( 5c ), p‐phenylenediamine ( 5d ), m‐phenylenediamine ( 5e ), 2,4‐diaminotoluene ( 5f ), and 1,5‐diaminonaphthalene ( 5g ) was developed by using a domestic microwave oven in the presence of a small amount of a polar organic medium such as o‐cresol. The polymerization reactions were also performed under two conventional methods: low temperature solution polycondensation in the presence of trimethylsilyl chloride, and a short period reflux conditions. A series of optically active poly(amide‐imide)s with inherent viscosity of 0.25–0.42 dL/g were obtained with high yield. All of the above polymers were fully characterized by IR, elemental analyses, and specific rotation techniques. Some structural characterizations and physical properties of these optically active poly (amide‐imide) s are reported. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2992–3000, 2004     

Synthesis,characterization, and properties of low viscosity tetra‐functional epoxy resin N,N,N′,N′‐ tetraglycidyl‐3,3′‐diethyl‐4,4′‐diaminodiphenylmethane

Tetra‐functional epoxy resin N,N,N′,N′‐tetraglycidyl‐3,3′‐diethyl‐4,4′‐diaminodiphenylmethane (TGDEDDM) was synthesized and characterized. The viscosity of TGDEDDM at 25°C was 7.2 Pa·s, much lower than that of N,N,N′,N′‐tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM). DSC analysis revealed that the reactivity of TGDEDDM with curing agent 4,4′‐diamino diphenylsulfone (DDS) was significantly lower than that of TGDDM. Owing to its lower viscosity and reactivity, TGDEDDM/DDS exhibited a much wider processing temperature window compared to TGDDM/DDS. Trifluoroborane ethylamine complex (BF₃‐MEA) was used to promote the curing of TGDEDDM/DDS to achieve a full cure, and the thermal and mechanical properties of the cured TGDEDDM were investigated and compared with those of the cured TGDDM. It transpired that, due to the introduction of ethyl groups, the heat resistance and flexural strength were reduced, while the modulus was enhanced. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 40009.     

Formation of honeycomb films based on a soluble polyimide synthesized from 2,2′‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]hexafluoropropane dianhydride and 3,3′‐dimethyl‐4,4′‐diaminodiphenylmethane

A soluble polyimide was synthesized from 2,2′‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]propane dianhydride (BPADA) and 3,3′‐dimethyl‐4,4′‐diaminodiphenylmethane (DMMDA) by a two‐step method, and it had good solubility both in strong bipolar solvents and in common low‐boiling‐point solvents. The BPADA–DMMDA polyimide was dissolved in chloroform (CHCl₃) and cast onto a glass substrate in a humid atmosphere. The BPADA–DMMDA/CHCl₃ solution easily formed honeycomb films. Some affecting factors, such as the polymer solution concentration, atmospheric humidity, and solvent volatility, were tested. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polyimides derived from 1,4‐bis [3‐oxy‐(N‐aminophthalimide)] benzene

A novel diamine, 1,4‐bis [3‐oxy‐(N‐aminophthalimide)] benzene (BOAPIB), was synthesized from 1,4‐bis [3‐oxy‐(N‐phenylphthalimide)] benzene and hydrazine. Its structure was determined via IR, ¹H NMR, and elemental analysis. A series of five‐member ring, hydrazine‐based polyimides were prepared from this diamine and various aromatic dianhydrides via one‐step polycondensation in p‐chlorophenol. The inherent viscosities of these polyimides were in the range of 0.17–0.61 dL/g. These polymers were soluble in polar aprotic solvents and phenols at room temperature. Thermogravimetric analysis (TGA) showed that the 5% weight‐loss temperatures of the polyimides were near 450°C in air and 500°C in nitrogen. Dynamic mechanical thermal analysis (DMTA) indicated that the glass‐transition temperatures (T_gs) of these polymers were in the range of 265–360°C. The wide‐angle X‐ray diffraction showed that all the polyimides were amorphous. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Curing behaviors and thermal properties of benzoxazine and N,N′‐(2, 2, 4‐trimethylhexane‐1, 6‐diyl) dimaleimide blend

A blend of bisphenol‐A based benzoxazine (BA‐a)/N, N′‐(2, 2, 4‐Trimethylhexane‐1, 6‐diyl) dimaleimide (TBMI) with the ratio of 1:1 was prepared and its curing behaviors were studied by differential scanning calorimetry (DSC), Fourier Transform Infrared (FTIR). The curing mechanism was proposed based on the semiquantitative analysis from FTIR spectra. The model compound was used to study the catalysis effect of BA‐a on the curing reaction of TBMI. It was found the curing reactions of BA‐a and TBMI not only proceeded simultaneously, but their coreactions also occurred. The research further indicated that negative oxygen ions from ring opening of benzoxazine mainly promoted the polymerization of maleimide groups, even though the amine group of benzoxazine had a positive effect on the reaction of maleimide groups. Besides, BA‐a and TBMI blends showed improved thermal properties based on the results from DMA and TGA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and characterization of novel soluble pyridine‐containing polyimides based on 4‐phenyl‐2,6‐bis[4‐(4‐aminophenoxy)phenyl]‐pyridine and various aromatic dianhydrides

A new kind of pyridine‐containing aromatic diamine monomer, 4‐phenyl‐2,6‐bis[4‐(4‐aminophenoxy)phenyl]‐pyridine (PAPP), was successfully synthesized by a modified chichibabin reaction of benzaldehyde and a substituted acetophenone, 4‐(4‐nitrophenoxy)‐acetophenone (NPAP), followed by a reduction of the resulting dinitro compound 4‐phenyl‐2,6‐bis[4‐(4‐nitrophenoxy)phenyl]‐pyridine (PNPP) with Pd/C and hydrazine monohydrate. The aromatic diamine was employed to synthesize a series of new pyridine‐containing polyimides by polycondensation with various aromatic dianhydrides in N‐methy‐2‐pyrrolidone (NMP) via the conventional two‐step method, i.e., ring‐opening polycondensation forming the poly (amic acid)s and further thermal or chemical imidization forming polyimides. The inherent viscosities of the resulting polyimides were in the range of 0.79–1.13 dL/g, and most of them were soluble in common organic solvents such as N,N‐dimethylacetamide (DMAc), NMP, and tetrahydrofuran (THF), etc. Meanwhile, strong and flexible polyimide films were obtained, which had good thermal stability, with the glass transition temperatures (T_g) of 268–338°C and the temperature at 5% weight loss of 521–548°C in air atmosphere, as well as outstanding mechanical properties with tensile strengths of 89.2–112.1 MPa and elongations at break of 9.5–15.4%. The polyimides also were found to possess low dielectric constants ranging from 2.53 to 3.11. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 212–219, 2007     

A highly selective polybenzimidazole‐4,4′‐(hexafluoroisopropylidene)bis(benzoic acid) membrane for high‐temperature hydrogen separation

A polymeric gas separation membrane utilizing polybenzimidazole based on 4,4′‐(hexafluoroisopropylidene)bis(benzoic acid) was prepared. The synthesized membrane has an effective permeating area of 8.3 cm² and a thickness of 30 ± 2 µm. Gas permeation properties of the membrane were determined using H₂, CO₂, CO, and N₂ at temperatures ranging from 24°C to 200°C. The PBI‐HFA membranes not only exhibited excellent H₂ permeability, but it also displayed superior gas separation performance particularly for H₂/N₂ and H₂/CO₂. The permeation parameters for both permeability and selectivity [ and α(H₂/N₂); and α(H₂/CO₂)] obtained for the new material were found to be dependent on trans‐membrane pressure difference as well as temperature, and were found to surpass those reported by Robeson in 2008. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42371.     

Thermal behavior and cured products of bis(4‐maleimidodiphenyl)methane,bis(isomaleimidodiphenyl)methane and 4,4′‐diaminodiphenyl methane mixtures

The thermal behavior of mixtures of bis(4‐maleimidophenyl) (A) with bis(4‐isomaleimidophenyl)methane (C) and their mixture with 4,4′‐diaminodiphenyl methane (D) were investigated by differential scanning calorimetry. The study of the binary system A/C in different proportions led us to determine an eutectic mixture at a molar fraction of C in the range of 0.7–0.9. The ternary ACD mixtures showed themselves able to participate in three principal reactions: polyaddition, ring‐opening addition, and homopolymerization. In each mixture studied the addition of diamine changed the melting point and maximum polymerization temperatures in the sense of a general decrease. The properties of the networks were studied by thermal analysis and through evaluation of water absorption. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3547–3556, 2003     

Fabrication and characterization of soluble,high thermal,and hydrophobic polyimides based on 4‐(3,5‐dimethoxyphenyl)‐2,6‐bis(4‐aminophenyl)pyridine

A novel aromatic diamine monomer, 4‐(3,5‐dimethoxyphenyl)‐2,6‐bis(4‐aminophenyl)pyridine (DPAP) was successfully synthesized by 4′‐nitroacetophenone and 3,5‐dimethoxybenzaldehyde as raw material. The structure of DPAP was confirmed by Fourier transform infrared, nuclear magnetic resonance, and mass analysis. A series of polyimides (PIs) were obtained by polycondensation with various dianhydrides via the conventional two‐step method. These PIs showed good solubility in organic solvents. They also presented high thermal stability, the glass transition temperatures (T_g) of polymers were in the range of 325–388 °C, and the temperature at 10% weight loss was in the range of 531–572 °C. Furthermore, these polymers also exhibited outstanding hydrophobicity with the contact angles in the range of 89.1°–93.5°. Moreover, the results of wide‐angle X‐ray diffraction (WAXD) confirmed these polymers showed amorphous structure. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45827.     

Preparation and properties of polyimides based on bis[3,5‐dimethyl‐4‐(4‐aminophenoxy)phenyl]methane

A series of polyimide (PI) thin films were synthesized based on bis[3,5‐dimethyl‐4‐(4‐aminophenoxy)phenyl]methane and conventional aromatic dianhydrides. The structures and properties of the thin films were measured with Fourier transform infrared, NMR, thermogravimetric analysis, dynamic mechanical analysis, and impedance analysis. The PI films exhibited glass‐transition temperatures in the range of 211–300°C and possessed initial thermal decomposition temperature reaching up to 457–482°C in air and 461–473°C in nitrogen. Some PI films had high solubility in organic solvents such as 1‐methyl‐2‐pyrrolidinone, N,N‐dimethylformamide, N,N‐dimethylacetamide, dimethyl sulfoxide, m‐cresol, tetrahydrofuran, and CHCl₃. The mechanical properties of these films were also examined. The dielectric constants of the films were in the range of 2.8–3.3 at 25°C. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1265–1270, 2007     

Reaction‐induced phase separation and resulting thermomechanical and surface properties of epoxy resin/poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) blends cured with 4,4′‐diaminodiphenylsulfone

We investigated the phase separation, cure kinetics and thermomechanical properties of diglycidyl ether of bisphenol‐A/4,4′‐diaminodiphenylsulfone/poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) (PEO–PPO–PEO) triblock copolymer (TBCP) blends. Fourier transform infrared spectroscopy, differential scanning calorimetry, and atomic force microscopy revealed that the blends exhibited heterogeneous phase morphology in which the TBCP formed dispersed domains in epoxy matrix, due to reaction induced phase separation. A fraction of phase‐separated PEO phase underwent partial crystallization whereas another fraction formed interphases between the dispersed domains and epoxy matrix. Moreover, the dispersed PEO chains improved the compatibility and interfacial adhesion between the matrix and domains and, consequently, significantly improved the mechanical properties of epoxy resin. Furthermore, the thermal degradation studies and contact angle measurements disclosed that the dispersed domains were well protected by the epoxy matrix. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44406.