共查询到19条相似文献,搜索用时 125 毫秒
1.
2.
SF/PF复合材料冲击性能的研究 总被引:2,自引:0,他引:2
研究了剑麻纤维(SF)的表面处理方式、纤维的含量、纤维的长度及与玻璃纤维混杂增强对SF/酚醛树脂(PF)复合材料冲击强度的影响,借助SEM观察复合材料的冲击断面,进行了微观结构分析。结果表明,SF经过碱处理后复合体系的冲击强度提高了34%,当SF的质量分数为40%、长度为6ram时,SF/PF复合材料冲击强度达到最大值,当SF与玻纤质量比为1:1时,复合材料冲击强度出现了混杂效应。 相似文献
3.
4.
剑麻增强醋酸纤维素复合材料的制备与性能研究 总被引:1,自引:0,他引:1
对剑麻(SF)进行乙醚化处理以改性纤维结钩和性能,得到改善纤维(ASF)。并通过挤出、模压工艺制备了剑麻增强醋酸纤维索(CA)复合材料。从纤维长度、结钩、热性能等力一面研究改性和加工工艺对SF的影响,同时研究了复合材料的力学性能。研究结果表明,SF和ASF使复合材料的拉伸性能和弯曲性能都得到了一定的增强。尽管ASF/CA复合材料在强度和模量上比SF/CA复合材料硝有逊色,但是由于ASF与基体相容性提高、柔韧性改善,从而其ASF/CA复合材料在断裂伸长率和冲山性能上优于SF/CA复合材料。 相似文献
5.
用自制的超分散剂对剑麻纤维(SF)表面改性,采用机械共混法及模压成型工艺制备SF/聚丙烯(PP)木塑复合材料.研究不同柔性链段、不同含量的超分散剂对复合材料力学性能、晶态结构及微观结构的影响.结果表明,SF经表面处理后与PP的界面黏结性增强,力学性能也得到了一定的提高,PP的晶体结构仍以α晶型为主. 相似文献
6.
7.
介绍了剑麻纤维(SF)的组成结构及其特点,并对SF在增强聚合物复合材料方面的应用和研究进展进行了概括,指出了开发这种复合材料的重要意义。 相似文献
8.
实验制备了蚕丝-聚乙烯醇/聚乙烯吡咯烷酮(SF-PVA/PVP)膜复合材料,并研究了SF的用量对SF-PVA/PVP膜复合材料结构和力学性能的影响。研究结果表明:SF与PVA/PVP膜复合材料具有良好的生物相容性,SF用量较少时可以在PVA/PVP膜基质中均匀分散;SF的加入会提高复合材料的力学性能,拉伸强度和弹性模量显著提高,断裂伸长率则明显降低,主要归因于PVA的—O—H和SF纤维的—N—H和C═O基团之间分别出现了强氢键;同时随着SF用量的增加,复合材料的土壤微生物降解能力显著增强,在SF-PVA/PVP薄膜中添加SF纤维有利于材料的生物降解。 相似文献
9.
10.
提出了一种新的纤维表面处理方法———不完全化学处理法。以该方法制备的非连续碱处理剑麻纤维(DASF)作为增强纤维,通过开炼压制制备了DASF/聚乳酸(PLA)复合材料。对比了未处理剑麻纤维(SF)、连续碱处理剑麻纤维(CASF)以及DASF制得的PLA复合材料力学性能,并通过扫描电镜(SEM)、体视显微镜对试样进行观察分析。研究了DASF长度与直径的变化,以及非连续碱处理方法、DASF质量分数对复合材料结构和性能的影响。结果表明,DASF/PLA复合材料中,纤维的长度多分布在1.6~3.1 mm范围内,直径小于SF而大于CASF。相比于连续碱处理,非连续碱处理可以进一步提高复合材料力学性能。纤维质量分数会影响DASF/PLA复合材料的力学性能,当纤维质量分数为30%时,DASF/PLA复合材料的力学性能最优。 相似文献
11.
剑麻纤维增强聚氯乙烯复合材料工艺与性能的研究 总被引:10,自引:1,他引:9
本文通过对剑麻纤维和聚氯乙烯基体改性,并变化成型参数,来研究它们对形成的复合材料力学性能和耐水性的影响,从而制订出剑麻纤维/聚氯乙烯复事材料的最佳成型工艺。 相似文献
12.
13.
Phenol formaldehyde resin (PF) reinforced with short sisal fibers (SF) were obtained by two methods, direct‐mixing and polymerization filling. Impact and bending properties of resulting composites were compared. Under the same compression molding conditions, polymerization filled composites showed better mechanical properties than those of direct‐mixed composites. The influences of fiber modifications on the mechanical properties of SF/PF in‐situ (polymerization filled) composites have been investigated. Treated‐SF‐reinforced composites have better mechanical properties than those of untreated‐SF‐reinforced composites. The effects of SF on water absorption tendencies of SF/PF composites have also been studied. In addition, sisal/glass (SF/GF) hybrid PF composites of alkali‐treated SF were prepared. Scanning electron microscopic studies were carried out to study the fiber‐matrix adhesion. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers 相似文献
14.
15.
Pretreatment of the sisal fiber (SF) grafting with L‐lactide (LA) monomer via a ring‐opening polymerization catalyzed by a Sn(II)‐based catalyst was performed to improve the interfacial adhesion between SF and poly (lactic acid) (PLA). Biocomposites from LA‐grafted SF (SF‐g‐LA) and PLA were prepared by compression molding with fiber weight fraction of 10, 20, 30, and 40%, and then were investigated in contrast with alkali‐treated sisal fiber (ASF) reinforced PLA composites and untreated SF reinforced PLA composites. PLA composites reinforced by half‐and‐half SF‐g‐LA/untreated SF (half SF‐g‐LA) were prepared and studied as well, considering the disadvantages of SF‐g‐LA. The results showed that both the tensile properties and flexural properties of the SF‐g‐LA reinforced PLA composites were improved noticeably as the introduction of SF‐g‐LA, compared with pure PLA, untreated SF reinforced PLA composites and ASF reinforced PLA composites. The mechanical properties of the half SF‐g‐LA reinforced PLA composites were not worse, even better in some aspects, than the SF‐g‐LA reinforced PLA composites. Fourier transform infrared analysis and differential scanning calorimetry analysis exhibited that both the chemical composition and crystal structure of the SFs changed after LA grafting. In addition, the fracture surface morphology of the composites was studied by scanning electron microscopy. The morphological studies demonstrated that a better adhesion between LA‐grafted SF and PLA matrix was achieved. POLYM. COMPOS., 37:802–809, 2016. © 2014 Society of Plastics Engineers 相似文献
16.
本文讨论了PET、PA短纤维(SF)与CPE热塑基复合材料的制备、基本力学性能和流变性能。探索了SF组分(种类、含量、L/D比)、粘合体系、工艺条件等对性能的影响。实验结果表明,HRH粘合体系可显著改善复合材料的力学性能。从兼顾复合材料的物理件能与加工流变性能的角度出发,在本实验条件下,取SF为15重量份、L/D为220为宜。 相似文献
17.
苯并噁嗪是近年来发展起来的一种新型的高性能复合材料基体树脂。本文较系统地综述了国内外碳纤维增强苯并噁嗪复合材料的研究进展,介绍了苯并噁嗪树脂及其复合材料的性能特点,指出了进一步的发展趋势。 相似文献
18.
长纤维增强热塑性复合材料的研究进展 总被引:10,自引:0,他引:10
本文论述了热塑性树脂基复合材料的发展特点。除介绍了最具发展潜力的长纤维增强热塑性复合材料的浸渍工艺和成型工艺外,还着重介绍了新型长纤维增强热塑性复合材料和其应用前景。 相似文献
19.
剑麻纤维/酚醛树脂复合材料力学性能的研究 总被引:8,自引:0,他引:8
采用剑麻纤维(SF)与酚醛树脂(PF)混合、辊炼、模压成型,制备SF/PF复合材料,并对其复合材料的冲击强度、弯曲强度、弯曲模量等进行测试。结果表明,剑麻纤维的表面处理方式、纤维的含量、纤维的长度以及与玻璃纤维混杂对复合材料体系力学性能影响较大。 相似文献