Studies of Gas Holdup in Bubble Column Reactors

Gas holdup in bubble columns has been investigated over a wide range of operational and geometrical parameters. A criterion has been developed for the prediction of the transitional velocity from the homogeneous to heterogeneous flow regime. Correlations for gas holdup in both regimes are developed and verified against experimental data.     

THEORETICAL PREDICTION OF GAS HOLDUP IN BUBBLE COLUMNS WITH NEWTONIAN AND NON-NEWTONIAN LIQUIDS

A simple model based on an energy balance which takes into account the friction losses at the gas-liquid interface and the slip velocity of single bubble is used to simulate the gas holdup in bubble columns containing Newtonian and non-Newtonian liquids which circulate in both laminar and turbulent flows. Experimental data available from the literature for bubble columns up to 7 m height and 1 m diameter with water and glycerol as Newtonian liquids and different solutions of CMC in a wide range of concentrations as non-Newtonian liquids are simulated with good agreement despite the simplifications made to describe the gas liquid flow regimes. Most of the differences between experimental and calculated gas holdup are justified on the basis of the simplifying assumptions.     

GAS-PHASE HOLDUP IN A SLURRY-BUBBLE COLUMN

Total and sectional gas-phase holdups are measured in a wide (0.305 m internal diameter) and long (3.7 m) glass bubble column al ambient conditions as a function of superficial gas velocity. Sectional gas holdup values vary along the length of the column and decrease as the height above the gas distributor plate increases in the transitional and turbulent flow regimes. In the discrete bubbling regime, the values are fairly constant in most of the column length except for a small lower portion where the values are significantly smaller than in the rest of the column. This is due to the formation of gas jets at the orifices of the distributor plate. The holdup values are dependent only on the mangitude of gas velocity and do not depend upon how it is approached, i.e., by increasing or decreasing the flow, in the turbulent-flow regime. This is not the case in the discrete and transitional gas-flow regimes. These characteristic variations in gas holdup are explained on the basis of the formation of bubbles in the lower region of the column and their growth by bubble coalescence prior to acquiring a stable bubble size.

Limited experimental data for the three-phase system (air-water-glass beads) indicate that gas holdup decreases as the concentration of glass beads is increased in the mixutre. This is attributed to the increased buoyancy effect in the presence of glass beads which increases the upthrust and hence the bubble velocity which results in the decrease of gas holdup. Total gas holdup data as a function of superficial gas velocity are compared with the predictions of four commonly used correlations and are also analysed in terms of the sectional measured gas-phase holdup data. The inferences that follow are significant.     

Relation of mechanical power to gas holdup and mass transfer in an agitated vessel

Two devices were developed, mechanical and electrical, to measure the mechanical power relative to superficial gas velocity and stirring speed in a mechanically agitated reactor. Two bubble regimes were demonstrated. The study of gas holdup, obtained from the residence time distribution, and the bubble size, determined by interfacial area measurement, confirm these two regimes of flow. Our results show that the gas holdup, the interfacial area, and the liquid-side mass transfer coefficient are increasing functions of the energy dissipated in the solution.     

湍动浆态床流体力学研究（Ⅰ）气含率及其分布规律

对高气速、高固含率、大塔径条件下的湍动浆态床平均气含率和气含率径向分布进行了实验测定,结合工业实验数据,归纳出可用于工业条件的气含率计算关联式,给出了简化的流体力学模型用于气含率分布的模拟。结果表明,浆态床气含率将随塔径增加而降低,固含率与塔径之间存在交互影响;同时,气含率的径向分布也随气速和塔径的增大而改变,存在明显的放大效应,简化模型能够较好地模拟实验结果。     

Hydrodynamics and bubble behaviour in a three-phase two-stage internal loop airlift reactor

Local hydrodynamics of a gas–liquid–solid system,such as bubble circulation regime,gas holdup,liquid velocity and axial profile of solid concentration,are studied in a two-stage internal loop airlift reactor.Empirical correlations for gas holdup and liquid velocity are proposed to ease the reactor design and scale-up.Different bubble circulation regimes were displayed in the first(lower) and second(upper) stages.Increasing superficial gas velocity and solid loading can promote regime transition of the second stage,and the gas holdup of the second stage is higher than that of the lower stage.In addition,the effects of solid loading on bubble behaviour are experimentally investigated for each stage.It is found that bubble size in the downcomer decreases with the presence of solid particles,and bubble size distribution widens under higher superficial gas velocity and lower solid loading.     

LOCAL HYDRODYNAMICS IN AN EXTERNAL LOOP AIRLIFT SLURRY REACTOR WITH AND WITHOUT A RESISTANCE-REGULATING ELEMENT

The hydrodynamic behavior of an external loop airlift slurry reactor (ALSR) with and without a resistance-regulating element was studied with a fiber optic probe and ultrasound Doppler velocimetry. The influences of the superficial gas velocity and solid holdup on the global gas holdup and radial profiles of the suspension circulation velocity in the downer and of gas holdup, bubble size, and bubble rise velocity in the riser were studied. Local measurements allow a better understanding of the flow behavior in the reactor and can be used for CFD modeling and validation. Experimental results show that the resistance-regulating element increases the gas holdup and decreases the suspension circulation velocity, indicating that an optimum design of the flow resistance is needed to obtain the maximum gas-liquid volumetric mass transfer coefficient for a specific superficial gas velocity. A high superficial gas velocity and low solid holdup are favorable for increased uniformity of the radial profile of the gas holdup and bubble rise velocity. Hydrodynamic models that predict the gas holdup and suspension circulation velocity were developed for an ALSR with and without a resistance-regulating element. Good agreement was obtained between measured and predicted values.     

Efficient dispersion in a modified two-phase non-Newtonian downflow bubble column

A comprehensive study of dispersion of gas-non-Newtonian fluid has been made in a modified downflow bubble column. Distribution of gas holdup in axial location has been anticipated from hydrostatic force balance. The experimental gas holdup data in such modified bubble column have been analyzed by slip velocity and drift-flux models. A correlation in terms of various physical, geometric and operating parameters of the present system has also been developed to analyze the gas holdup.     

LOCAL HYDRODYNAMICS IN AN EXTERNAL LOOP AIRLIFT SLURRY REACTOR WITH AND WITHOUT A RESISTANCE-REGULATING ELEMENT

The hydrodynamic behavior of an external loop airlift slurry reactor (ALSR) with and without a resistance-regulating element was studied with a fiber optic probe and ultrasound Doppler velocimetry. The influences of the superficial gas velocity and solid holdup on the global gas holdup and radial profiles of the suspension circulation velocity in the downer and of gas holdup, bubble size, and bubble rise velocity in the riser were studied. Local measurements allow a better understanding of the flow behavior in the reactor and can be used for CFD modeling and validation. Experimental results show that the resistance-regulating element increases the gas holdup and decreases the suspension circulation velocity, indicating that an optimum design of the flow resistance is needed to obtain the maximum gas-liquid volumetric mass transfer coefficient for a specific superficial gas velocity. A high superficial gas velocity and low solid holdup are favorable for increased uniformity of the radial profile of the gas holdup and bubble rise velocity. Hydrodynamic models that predict the gas holdup and suspension circulation velocity were developed for an ALSR with and without a resistance-regulating element. Good agreement was obtained between measured and predicted values.     

A gas holdup model for cocurrent air-water-fiber bubble columns

A gas holdup model is developed for cocurrent air-water-fiber bubble column flows using the drift-flux model. The model coefficients are estimated using a nonlinear least square method and systematically acquired experimental data. The model correlates gas holdup with superficial gas and liquid velocity, and fiber type and mass fraction. The model reproduces most experimental data within ±10% error and all but 3 of the 3839 experimental data points within ±15% error. It also accurately predicts air-water bubble column gas holdup data; these data were not used in estimating the model coefficients. The physical implications of the model coefficients are also discussed.     

Flow regimes and mass transfer in counter-current bubble columns

Counter current bubble columns have the feature that specific gas-liquid interfacial area and gas holdup are larger than those for standard and cocurrent bubble columns. In this study, three different flow regimes, churn-turbulent flow, bubble flow and bubble down-flow, have been observed in a counter-current bubble column and correlations of gas holdup and volumetric liquid-phase mass transfer coefficient have been proposed as functions of operating variables such as the superficial velocities of gas and liquid, the gas-liquid slip velocity and the liquid properties.     

Hydrodynamics of a Multi‐Stage Internal Loop Airlift Reactor

The local hydrodynamic properties in a multi‐stage internal loop airlift reactor were investigated in this study. The gas‐liquid two‐phase flow hydrodynamic properties, including gas holdup, bubble velocity, bubble diameter, and liquid circulation velocity at various stages were measured by dual electrical resistivity probes and conductivity cells. Detailed studies on the gas holdup, bubble velocity, bubble diameter, and liquid circulation velocity were conducted with respect to various values of superficial gas. The Zuber and Findlay drift flux model was used to represent the variation of slip velocity with total gas‐liquid velocity at various stages and the model fits the data well.     

Local hydrodynamics of gas–liquid-nanoparticles three-phase fluidization

The laser Doppler anemometer (LDA) and conductivity probes were used for measuring the local hydrodynamic performances such as gas holdup and liquid velocity in a lab-scale gas–liquid–TiO₂ nanoparticles three-phase bubble column. Effects of operating parameters on the local gas holdup and liquid velocity were investigated systematically. Experimental results showed that local averaged axial liquid velocity and local averaged gas holdup increased with increasing superficial gas velocity but decreased with increasing TiO₂ nanoparticles loading and the axial distance from the bottom of the bubble column. A three-dimensional computational fluid dynamic (CFD) model was developed in this paper to simulate the structure of gas–liquid–TiO₂ nanoparticles three-phase flow in the bubble column. The time-averaged and time-dependent predictions were compared with experimental data for model validation. A successful prediction of instantaneous local gas holdup, gas velocity, and liquid velocity were also presented.     

Gas holdup characteristics in a flotation column with different solids

This paper presents the effect of process variables on gas holdup. It was measured by volume expansion method in a continuously operating flotation column using coal and sphalerite. It was observed that addition of both solids reduced gas holdup. Increase in solid concentration and particle size reduced gas holdup. Also, increase in gas velocity and frother concentration increased the gas holdup as amount of gas increased and bubble surface property favored the formation of small bubbles. An empirical mathematical model was developed to predict gas holdup. The predicted results were in good agreement with the experimental and available published data.     

Modelling Gas Holdup in Flotation Column Froths

A one‐dimensional steady‐state model is developed for the prediction of axial variation of the gas holdup in flotation column froths. Froth is considered as an inverse fluidized bed of bubbles and hence the frictional pressure gradient is obtained based on the energy balance. Pressure gradient can also be obtained from the Ergun equation with adjustable constants. The model correctly captures the effect of superficial gas velocity, superficial liquid velocity and bubble diameter on the variation of the gas holdup along the froth height. The predictions of the model are in agreement with the experimental data from the literature.     

Local hydrodynamic parameters of bubble column reactors operating with non‐Newtonian liquids: Experiments and models development

The effects of liquid phase rheology on the local hydrodynamics of bubble column reactors operating with non‐Newtonian liquids are investigated. Local bubble properties, including bubble frequency, bubble chord length, and bubble rise velocity, are measured by placing two in‐house made optical fiber probes at various locations within a bubble column reactor operating with different non‐Newtonian liquids. It was found that the presence of elasticity can noticeably increase the bubble frequency but decreases the bubble chord length and its rise velocity. The radial profiles of bubble frequency, bubble chord length, and bubble rise velocity are shown to be relatively flat at low superficial gas velocity while they become parabolic at high superficial gas velocity. Moreover, the bubble size and gas holdup are correlated with respect to dimensionless groups by considering the ratio between dynamic moduli of viscoelastic liquids. The novel proposed correlations are capable of predicting the experimental data of bubble size and gas holdup within a mean absolute percentage error of 9.3% and 10%, respectively. © 2015 American Institute of Chemical Engineers AIChE J, 62: 1382–1396, 2016     

鼓泡塔中气泡尺寸分布和局部气含率研究

在内径为0.38 m的鼓泡塔中采用双电导探针法对不同通气速率下的气泡尺寸分布和局部气含率进行了实验研究,分析了气泡尺寸的概率密度分布。结果表明:气泡尺寸随轴向高度的增加而增大,随径向距离增加而减小;鼓泡塔中气液流动可分为过渡流域和充分发展流域,在过渡流域气含率随轴向高度增加而增大,在充分发展流域气含率趋于均值,径向局部气含率分布呈抛物线型下降。高气速下气泡尺寸概率密度分布比低气速下宽,且随轴向高度的增加分布变宽。     

CFD analysis of two‐phase turbulent flow in internal airlift reactors

The hydrodynamic performance of three internal airlift reactor configurations was studied by the Eulerian–Eulerian k–ε model for a two‐phase turbulent flow. Comparative evaluation of different drag and lift force coefficient models in terms of liquid velocity in the riser and downcomer and gas holdup in the riser was highlighted. Drag correlations as a function of Eötvös number performed better results in comparison to the drag expressions related to Reynolds number. However, the drag correlation as a function of both Reynolds and Eötvös numbers fitted well with experimental results for the riser gas holdup and downcomer liquid velocity in configurations I and II. Positive lift coefficients increase the liquid velocity and decrease the riser gas holdup, while opposite results were obtained for negative values. By studying the effects of bubble size and their shape, the smaller bubbles provide a lower liquid velocity and a gas holdup. The effects of bubble‐induced turbulence and other non‐drag closure models such as turbulent dispersion and added mass forces were analysed. The gas velocity and gas holdup distributions, liquid velocity in the riser and downcomer, vectors of velocity magnitude and streamlines for liquid phase, the dynamics of gas holdup distribution and turbulent viscosity at different superficial gas velocities for different reactor configurations were computed. The effects of various geometrical parameters such as the draft tube clearance and the ratio of the riser to the downcomer cross‐sectional area on liquid velocities in the riser and the downcomer, the gas velocity and the gas holdup were explored. © 2011 Canadian Society for Chemical Engineering     

Behavior of gas bubbles in a concentric cylindrical airlift column

Using a light transmission optical probe, the effect of superficial gas velocity on bubble properties(bubble size, bubble rising velocity, bubble frequency and local gas holdup) at axial and radial positions was determined in the riser and the downcomer of a concentric cylindrical airlift reactor. The vertical bubble length, the bubble rising velocity and the bubble frequency at axis in the riser increased with increasing superficial gas velocity and the bed height. The radial distribution of the local gas holdup, vertical bubble length and bubble frequency in the riser and the downcomer were found to be non-uniform. The profiles of the local gas holdup, vertical bubble length and bubble rising velocity in the riser were shown as parabolic shapes. The local gas holdup, the vertical bubble length and the bubble frequency in the downcomer changed with superficial gas velocity and the distance from the top of the draft tube.     

Enhancement in gas holdup in bubble columns through use of vibrating internals

Including internals in bubble columns is known to enhance the gas holdup. In this paper, a method to achieve this objective substantially has been proposed via the use of vibrating helical spring internals. Experimental observations on effect of vibrating internals such as vibrating helical springs on gas holdup in bubble columns are presented. Effects of superficial gas velocity, H/D ratio (height of the static liquid to column diameter ratio), volume fraction of helical springs, and thickness of the helical spring wires on hydrodynamics parameters are studied. Increase in gas holdup up to 135% is observed by using vibrating helical spring internals in bubble columns compared to bubble columns without internals. This method offers a simple, cost‐effective, and easy way to enhance gas holdup even at high gas fluxes. It has been reported that this enhancement stems from the fact that the vibrating springs breakup the gas into fine bubbles, which effectively reduces their rise velocity and enhances their average residence time in the liquid column.