Fabrication,tunable fluorescence emission and energy transfer of Tm3+-Dy3+ co-activated P2O5–B2O3–SrO–K2O glasses

A growing demand for white light-emitting diodes (W-LEDs) gives rise to continuous exploration of functional fluorescence glasses. In this paper, Tm³⁺/Dy³⁺ single- and co-doped glasses with composition (in mol%) of 30P₂O₅–10B₂O₃–23SrO–37K₂O were synthesized using the melt-quenching method in air. The physical properties, glass structure, luminescence characteristics and energy transfer mechanism of the glasses were systematically studied. As glass network modifiers, Tm³⁺ and Dy³⁺ ions can densify the glass structure. Excitation wavelength and doping concentration of Tm³⁺/Dy³⁺ ions have a direct impact on the emission intensities of blue and orange light as well as the color coordinate of the as-prepared glasses. A white light very close to standard white light can be obtained under 354 nm excitation when the content of Tm³⁺ and Dy³⁺ is 0.2 mol% and 1.0 mol%, respectively. The results of the emission spectra and decay curves reveal the existence of energy transfer from Tm³⁺ to Dy³⁺. The analytic results based on the Inokuti-Hirayama model indicate that the electrical dipole-dipole interaction may be the main mechanism of energy transfer. Moreover, Tm³⁺/Dy³⁺ co-activated glass phosphor has good thermal stability and chrominance stability and it is a promising candidate for white LEDs and display device.     

Degradation-controlling mechanisms in natural organic acid solutions of CaO–Al2O3–SiO2–B2O3 glass-ceramics by partially substituting Ca2+ with Ba2+ and Sr2+

The degradation of environmentally friendly CaO–Al₂O₃–SiO₂–B₂O₃ (CASB) glass-ceramics, which consist of anorthite and glass phase, was investigated in three natural organic acid solutions. The results indicated that citric acid had the most significant effect on the degradation of CASB glass-ceramics. While the chemical stability of anorthite is relatively poor, the glass phase also contributed significantly to the effective degradation of CASB glass-ceramics. Subsequently, Ba²⁺ or Sr²⁺ was used for full or partial substitution of Ca²⁺ in CASB glass-ceramics, and the degradation-controlling mechanism of the substituted CASB glass-ceramics was further researched. The full substitution of Ca²⁺ in CASB glass-ceramics by the two cations resulted in the occurrence of borate [BO₄] units in the glass phases, and the interlinkage of [BO₄] with broken silicate [SiO₄] network structures caused a complementary network effect. Consequently, the degradation of CASB glass-ceramics by organic acids was reduced due to the improvements in the chemical stability of the modified glass-ceramics. Additionally, degradation control can also be achieved based on a mixed-alkali effect, originating from the partial substitution of Ca²⁺ in CASB glass-ceramics by Ba²⁺ or Sr²⁺. The degradable glass-ceramics have the potential to be applied in low-temperature co-fired ceramic technology because of their good physical properties, which include a dielectric constant of 3–5, a dielectric loss as low as 10⁻³, a coefficient of thermal expansion of 3–9 × 10⁻⁶/°C, and an average bending strength of about 47 MPa. Noticeably, the development of the degradable glass-ceramics is helpful to the low-cost and pollution-free recycling of valuable metal electrodes, which is significant for the sustainable development of electronic packaging technologies.     

A comparative study of the magnetic and microwave properties of Al3+ and In3+ substituted Mg–Mn ferrites

The effect of substitution of diamagnetic Al³⁺ and In³⁺ ions for partial Fe³⁺ ions in a spinel lattice on the magnetic and microwave properties of magnesium–manganese (Mg–Mn) ferrites has been studied. Three kinds of Mg–Mn based ferrites with compositions of Mg_0.9Mn_0.1Fe₂O₄, Mg_0.9Mn_0.1Al_0.1Fe_1.9O₄, and Mg_0.9Mn_0.1In_0.1Fe_1.9O₄ were prepared by the solid-state reaction route. Each mixture of high-purity starting materials (oxide powders) in stoichiometric amounts was calcined at 1100 °C for 4 h, and the debinded green compacts were sintered at 1350 °C for 4 h. XRD examination confirmed that the sintered ferrite samples had a single-phase cubic spinel structure. The incorporation of Al³⁺ or In³⁺ ions in place of Fe³⁺ ions in Mg–Mn ferrites increased the average particle size, decreased the Curie temperature, and resulted in a broader resonance linewidth as compared to un-substituted Mg–Mn ferrites in the X-band. In this study, the In³⁺ substituted Mg–Mn ferrites exhibited the highest saturation magnetization of 35.7 emu/g, the lowest coercivity of 4.1 Oe, and the highest Q×f value of 1050 GHz at a frequency of 6.5 GHz.     

Thermal Stability and Crystallization Kinetics of MgO–Al2O3–B2O3–SiO2 Glasses

To support commercialization of the MgO–Al₂O₃–B₂O–SiO₂-based low-dielectric glass fibers, crystallization characteristics of the relevant glasses was investigated under various heat-treatment conditions. The study focused on the effects of iron on the related thermal properties and crystallization kinetics. Both air-cooled and nucleation-treated samples were characterized by using the differential thermal analysis/differential scanning calorimeter method between room temperature and 1200°C. A collected set of properties covers glass transition temperature (T_g), maximum crystallization temperature (T_p), specific heat (ΔC_p), enthalpy of crystallization (ΔH_cryst), and thermal stability (ΔT=T_p—T_g). Using the Kinssiger method, the activation energy of crystallization was determined. Crystalline phases in the samples having various thermal histories were determined using powder X-ray diffraction (XRD) and/or in situ high-temperature XRD method. Selective scanning electron microscope/energy-dispersive spectroscopy analysis provided evidence that crystal density in the glass is affected by the iron concentration. Glass network structures, for air-cooled and heat-treated samples, were examined using a midinfrared spectroscopic method. Combining all of the results from our study, iron in glass is believed to function as a nucleation agent enhancing crystal population density in the melt without altering a primary phase field. By comparing the XRD data of the glasses in two forms (bulk versus powder), the following conclusions can be reached. The low-dielectric glass melt in commercial operation should be resistant to crystallization above 1100°C. Microscopic amorphous phase separation, possibly a borate-enriched phase separating from the silicate-enriched continuous phase can occur only if the melt is held at temperatures below 1100°C, that is, below the glass immiscibility temperature. The study concludes that neither crystallization nor amorphous phase separation will be expected for drawing fibers between 1200°C and 1300°C in a commercial operation.     

Mechanical and functional properties of Al2O3–ZrO2–MWCNTs nanocomposites

Multi-walled carbon nanotubes (MWCNTs) are often reported as additives improving mechanical and functional properties of ceramic composites. However, despite tremendous efforts in the field in the past 20 years, the results are still inconclusive. This paper studies room temperature properties of the composites with polycrystalline alumina matrix reinforced with 0.5–2 vol.% MWCNTs (composites AC) and zirconia toughened alumina with 5 vol.% of yttria partially stabilised zirconia (3Y-PSZ) containing 0.5–2 vol.% of MWCNTs (composites AZC). Dense composites were prepared through wet mixing of the respective powders with functionalised MWCNTs, followed by freeze granulation, and hot-pressing of granulated powders. Room temperature bending strength, Young's modulus, indentation fracture toughness, thermal and electrical conductivity of the composites were studied, and related to their composition and microstructure. Slight increase of Young's modulus, indentation fracture toughness, bending strength, and thermal conductivity was observed at the MWCNTs contents ≤1 vol.%. At higher MWCNTs contents the properties were impaired by agglomeration of the MWCNTs. The DC electrical conductivity increased with increasing volume fraction of the MWCNTs.     

Thermal and devitrification behavior of CaO–Ga2O3–SiO2 glasses

A study of the influence of the substitution of Ga₂O₃ for CaO, at constant O/Si ratio, on thermal properties and non-isothermal devitrification of 2.5CaO.2SiO₂ is reported. Differential thermal analysis (DTA) and X-ray diffraction analysis were used. The X-ray diffraction pattern of the crystallized Ga₂O₃ base glass shows that the αCaO SiO₂, that should be stable only above 1125°C, forms in the temperature range 900–1000°C. A new ternary crystalline phase, whose reflections are not reported in the JCPDS cards, was found to form during crystallization of the glass. The glass transformation temperature, T_g, and softening, T_s, temperature decrease as Ga₂O₃ is substituted for CaO. This is the result of the substitution of the network modifying cation Ca²⁺, of higher coordination number, by a network forming cation Ga³⁺ in fourfold coordination, in a composition range of relative insensitivity to changes of covalent cross-linking density. The crystal growth activation energy, E_c, decreases with substitution; this is the consequence of the decrease of the structural rigidity and of the shift of crystallization to a higher temperature range. Devitrification involves a mechanism of surface nucleation; surface nuclei behaving as bulk nuclei in samples that soften and sinter before devitryfing.     

Influence of La3+ additions on the phase behaviour and antibacterial properties of ZrO2–SiO2 binary oxides

The present study reports the influence of lanthanum (La³⁺) content on the phase stability and antibacterial activity of ZrO₂–SiO₂ binary oxides. Four different concentrations of La³⁺ additions in ZrO₂–SiO₂ binary oxides were synthesized using a sol–gel technique. Heat treatment of the synthesized powders resulted in the formation of t-ZrO₂ phase at 1000 °C. Heat treatment beyond 1000 °C resulted in the phase degradation of t-ZrO₂ to yield m-ZrO₂ and ZrSiO₄. Results from antibacterial tests confirmed the potential activity of La³⁺ doped ZrO₂–SiO₂ binary oxides in countering the microbial invasion.     

Optical properties of novel oxyfluoride glasses on the systems of LaF3–LaO3/2–NbO5/2 and LaF3–LaO3/2–NbO5/2–AlO3/2

Oxyfluoride glasses of xLaF₃–(60 − x)LaO_3/2–40NbO_5/2 (x = 0, 5, 10, 35) and xLaF₃–(60 − x)LaO_3/2–30NbO_5/2–10AlO_3/2 (x = 0, 10, 20, 30) were prepared using a levitation technique. Both the glass-transition temperature, T_g, and onset crystallization temperature, T_c, were lowered by substituting a part of the oxygen with fluorine in the glasses. An appropriate amount of fluorine maximized the difference between the temperatures, ΔT (= T_c − T_g), indicating the improvement in the glass-forming ability. The atomic packing densities of the glasses were approximately 60%, which gradually increased with the fluorine content. The absorption edge of the glasses shifted toward the shorter wavelength region in the ultraviolet spectra and toward the longer region in the infrared spectra by fluorine substitution. In addition, in one of the oxyfluoride glasses, a wide transparency from 307 nm to 9.2 µm was realized. Furthermore, the glass exhibited superior optical properties, with a combination of a high refractive index, n_d, of 2.020 and low wavelength dispersion, v_d, of 30.1. The effect of fluorine substitution on the n_d and its v_d was analyzed using the Lorentz–Lorenz dispersion formula.     

Fabrication and microstructure of Al2O3–ZrO2(3Y)–SiC nanocomposites

Al₂O₃–ZrO₂(3Y)–SiC composite powder was prepared by the heterogeneous precipitation method. Calcinating temperature of the powder was important to obtain dense sintered body. The nanocomposites were got by hot-pressing, and addition of ZrO₂ did not raise the sintering temperature. Some Al₂O₃ grain shape was elongated, and Al₂O₃ grain size was about μm. Nano SiC particles were observed uniformly distributing throughout the composites, and most of them were located within the matrix grains. Because SiC particles located within ZrO₂ grains influenced the phase transformation of ZrO₂, the sintering of nanocomposites, which controlled grain size and transformable ZrO₂ amount, become important to get high performance. The strength of 80 wt% Al₂O₃–15 wt% ZrO₂–5 wt% SiC nanocomposites was 555 MPa, and toughness was 3·8 MPa m^1/2, which were higher than those of monolithic Al₂O₃ ceramics. ©     

Application of Judd–Ofelt theory in analyzing Nd3+ doped SrF2 and CaF2 transparent ceramics

Nd³⁺ doped SrF₂ and CaF₂ transparent ceramics were fabricated by vacuum hot-press sintering and the absorption spectra, emission spectra as well as luminescence decays of the samples were measured. Judd-Ofelt (J–O) theory was used to analyze the optical performance of Nd³⁺ in these two isostructural hosts. The Nd: SrF₂ transparent ceramic was found to have smaller line strength, larger radiative lifetime and smaller Ω₂ value (corresponding to more ionic Nd³⁺-ligand bonding and more symmetry of Nd³⁺ environment). These features made it easier for Nd: SrF₂ to realize population inversion and strong emission, thus doing good to laser performance. The strong emission of ⁴F_3/2 → ⁴I_9/2 transition in Nd: SrF₂, which was predicted by J–O theory and demonstrated by luminescence spectrum, made it possible to achieve effective laser output around 900 nm. The intensity parameters and radiative lifetimes of ceramics were found comparable with their corresponding single crystals.     

Electrochemistry of molten LiCl–KCl–CrCl3 and LiCl–KCl–CrCl2 mixtures

Chemical reactions during dissolution of CrCl3 or CrCl2 in molten LiCl–KCL eutectic have been demonstrated to occur, but the nature of the reactions is not yet well understood. Reduction of CrCl3 to chromium metal occurs through two well-characterized electrochemical steps, at approximately +0.1 and –0.9 V vs Ag/AgCl. Each step was studied in the 0.025–0.085 molar CrCl3 concentration range, at various temperatures between 375 and 550 °C. The Cr(iii)/Cr(ii) electron transfer step exhibited reversible behaviour under all the experimental conditions studied. In contrast, the Cr(ii)/Cr(0) step could involve Cr(ii) adsorbed species and initial chromium electrocrystallization phenomena, mainly depending on the nature of the substrate.     

Fabrication of double-cladding Ho3+/Tm3+ co-doped Bi2O3–GeO2–Ga2O3–BaF2 glass fiber and its performance in a 2.0-μm laser

A novel double-cladding Ho³⁺/Tm³⁺ co-doped Bi₂O₃–GeO₂–Ga₂O₃–BaF₂ glass fiber, which can be applied to a 2.0-μm infrared laser, was fabricated by a rod-tube drawing method. The thermal properties of the glass were studied by differential scanning calorimetry. It showed good thermal stability and matching thermal expansion coefficient for fiber drawing when T_x−T_g > 193°C and the maximum difference of the thermal expansion coefficient is 3.55 × 10⁻⁶/°C or less. The 2.0-μm luminescence characteristics were studied using the central wavelength of 808 nm pump light excitation. The results show that when the concentration ratio of Ho³⁺/Tm³⁺ reaches 0.5 mol%:1.0 mol%, the maximum fluorescence intensity was obtained in the core glass, the emission cross section reached 10.09 × 10⁻²¹ cm², and the maximum phonon energy was 751 cm⁻¹. In this paper, a continuous laser output with a maximum power of 0.986 W and a wavelength of 2030 nm was obtained using an erbium-doped fiber laser as a pump source in a 0.5 m long Ho³⁺/Tm³⁺ co-doped glass fiber. In short, the results show that Ho³⁺/Tm³⁺ co-doped 36Bi₂O₃–30GeO₂–15Ga₂O₃–10BaF₂–9Na₂O glass fiber has excellent laser properties, and it is an ideal mid-infrared fiber material for a 2.0-μm fiber laser with excellent characteristics     

Sintering behavior and microwave dielectric properties of 0.67CaTiO3–0.33LaAlO3 ceramics modified by B2O3–Li2O–Al2O3 and CeO2

A low temperature sintering method was used to avoid the relatively high sintering temperatures typically required to prepare 0.67CaTiO₃–0.33LaAlO₃ (CTLA) ceramics. Additionally, CeO₂ was introduced into the CTLA ceramics as an oxygen-storage material to improve their microwave dielectric properties. 0.67CaTiO₃–0.33LaAlO₃ ceramics co-doped with B₂O₃–Li₂O–Al₂O₃ and CeO₂ were prepared by a conventional two-step solid-state reaction process. The sintering behavior, crystal structure, surface morphology, and microwave dielectric proprieties of the prepared ceramic samples were studied, and the reaction mechanism of CeO₂ was elucidated. CTLA+0.05 wt% BLA+3 wt% CeO₂ ceramics sintered at 1360 °C for 4 h exhibited the optimal microwave dielectric properties: dielectric constant (ε_r)=45.02, quality factor (Q×f)=43102 GHz, and temperature coefficient of resonant frequency (τ_f)=2.1 ppm/°C. The successful preparation of high-performance microwave dielectric ceramics provides a direction for the future development and commercialization of CTLA ceramics.     

The corrosion resistance of microsilica-containing Al2O3–MgO and Al2O3–spinel castables

Microsilica addition in Al₂O₃–MgO and Al₂O₃–spinel castables helps to improve their flowability and partially accommodate their residual expansion after firing. Nevertheless, there is a lack of conclusive statements in the literature regarding the effects of microsilica on one of the main requisites for steel ladle refractories: corrosion resistance. In the present work, the performance of alumina–magnesia and alumina–spinel with or without microsilica when in contact with a steel ladle slag was evaluated based on three aspects: the material's physical properties, its chemical composition and the microstructural features before the slag attack. According to the attained results, microsilica induced liquid formation and pore growth during sintering, favoring the physical slag infiltration. Moreover, due to this liquid, CA₆ was formed in the matrix, mainly for the Al₂O₃–spinel composition, which also favored the castable dissolution into the molten slag.     

Influence of Ge and GeO2 on the microstructure and varistor properties of TiO2–Ta2O5–CaCO3 ceramics

This study investigated the effect of elemental crystal Ge or/and GeO₂ doping on the microstructure and varistor properties of TiO₂–Ta₂O₅–CaCO₃ varistor ceramics, which were prepared via the traditional ball milling–molding–sintering process. X-ray diffraction, scanning electron microscopy, scanning transmission electron microscopy-energy dispersive X-ray spectroscopy, scanning electron microscopy-energy dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy demonstrated that co-doping with Ge and GeO₂ changed the microstructure of TiO₂–Ta₂O₅–CaCO₃ ceramics, thereby increasing the nonlinear coefficient and decreasing the breakdown voltage. The optimum doping concentrations of Ta₂O₅, CaCO₃, Ge, and GeO₂ exhibited the highest nonlinear coefficient (α=14.6), a lower breakdown voltage (E_B=18.7 V mm⁻¹), the least leakage current (J_L=10.5 μA cm⁻²), and the highest grain boundary barrier (Φ_B=1.05 eV). In addition, Ge and GeO₂ function as sintering aids, which reduce the sintering temperature because of their low melting points.     

Analysis of the Composition of CuI–As2Se3 and CuI–PbI2–As2Se3 Chalcogenide Films by X-ray Fluorescence Spectroscopy

The chalcogenide films As₂Se₃, CuI–As₂Se₃, and CuI–PbI₂–As₂Se₃ are prepared through chemical deposition from an organic solvent and investigated by X-ray fluorescence spectroscopy. The contents of the main components of the chalcogenide films are compared by analyzing the intensity ratios for the AsK , SeK , and CuK lines. It is found that the content of the main components (As, Se, and Cu) is virtually the same in binary chalcogenide, pseudobinary, and multicomponent chalcogenide systems, no matter what the technique used for preparing the materials (films deposited from solutions of chalcogenide glasses in n-butylamine and bulk glasses). This result is consistent with a model of dissolution of vitreous semiconductors in organic bases (amine) according to which the fundamental properties of bulk glasses remain unchanged upon formation of the films. The experimental data indicate an analogy between the properties of the multicomponent chalcogenide glasses CuI–As₂Se₃ and CuI–PbI₂–As₂Se₃ and the chalcogenide glass–based films.     

A Significant Role of Tb2O3 on the Optical Properties and Radiation Shielding Performance of Ga2O3–B2O3–Al2O3–GeO2 Glasses

Journal of Inorganic and Organometallic Polymers and Materials - This research article focuses on the significant role of Tb2O3 content on the optical properties and radiation shielding performance...     

Effect of CaO doping on the properties and crystallization behavior of Y2O3–Al2O3–SiO2 glass

Nowadays, Y₂O₃–Al₂O₃–SiO₂ (YAS) glass joining is considered to be a promising scheme for nuclear-grade continuous silicon carbide (SiC) fiber reinforced SiC matrix composites (SiC/SiC). CaO has great potential for nuclear applications since it has low reactivity and low decay rate under nuclear irradiation. In this paper, the effect of CaO doping on the structure, thermophysical properties, and crystallization behavior of YAS glass was systematically studied. As the CaO doping content increased, the number of bridge oxygens and the viscosity at high temperatures reduced gradually. After heat treatment at 1400 °C, the main phases in YAS glass were β-Y₂Si₂O₇, mullite, and SiO₂ (coexistence of crystalline and glass phases), while that with 3.0% CaO doping turned into a single glassy phase under the same treatment conditions. Moreover, a structural model and the modification mechanism were proposed, which provided a theoretical basis for the subsequent component design and optimization.