Enhanced pyroelectric response from domain-engineered lead-free (K0.5Bi0.5TiO3-BaTiO3)-Na0.5Bi0.5TiO3 ferroelectric ceramics

Enhanced pyroelectric response is achieved via domain engineering from [001] grain-oriented, tetragonal-phase, lead-free 0.2(2/3K_0.5Bi_0.5TiO₃-1/3BaTiO₃)-0.8Na_0.5Bi_0.5TiO₃ (KBT-BT-NBT) ceramics prepared by a templated grain growth method. The [001] crystallographic orientation leads to large polarization in tetragonal symmetry; therefore, texturing along this direction is employed to enhance the pyroelectricity. X-ray diffraction analysis revealed a Lotgering factor (degree of texturing) of 93 % along the [001] crystallographic direction. The textured KBT-BT-NBT lead-free ceramics showed comparable pyroelectric figures of merit to those of lead-based ferroelectric materials at room temperature (RT). In addition to the enhanced pyroelectric response at RT, an enormous enhancement in the pyroelectric response (from 1750 to 90,900 μC m^?2 K^?1) was achieved at the depolarization temperature because of the sharp ferroelectric to antiferroelectric phase transition owing to coherent 180° domain switching. These results will motivate the development of a wide range of lead-free pyroelectric devices, such as thermal sensors and infra-red detectors.     

Texture development and dielectric relaxor behavior of 0.80Na0.5Bi0.5TiO3–0.20K0.5Bi0.5TiO3 ceramics templated by plate-like NaNbO3 particles

Plate-like NaNbO₃ particles were used as templates to fabricate grain-oriented 0.96(0.8Na_0.5Bi_0.5TiO₃–0.2 K_0.5Bi_0.5TiO₃)–0.04NaNbO₃ (NKBT) ceramics. The effects of the sintering temperature and the soaking time on the grain orientation and the microstructure of the textured NKBT ceramics were investigated, and the dielectric relaxor behavior is discussed. The results show that textured ceramics were successfully obtained with orientation factor more than 0.8. The textured ceramics have a microstructure with strip-like grains aligning in the direction parallel to the casting plane. The degree of grain orientation increases initially, then decreases with increasing sintering temperature, and increases continuously with increasing soaking time. The textured NKBT ceramics shows obvious dielectric relaxor characteristics which can be well explained by microdomain–macrodomain transition theory with calculating criterion K. The results show that formation of texture is beneficial to microdomain–macrodomain transition, which lead to weaken relaxor behavior and raise the dielectric constant at T_tr.     

Microstructure and piezoelectric properties of textured (Na0.84K0.16)0.5Bi0.5TiO3 lead-free ceramics

Textured (Na,K)_0.5Bi_0.5TiO₃ ceramics were fabricated by reactive-templated grain growth in combination with tape casting. The effects of sintering conditions on the grain orientation and the piezoelectric properties of the textured (Na,K)_0.5Bi_0.5TiO₃ ceramics were investigated. The results show that the textured ceramics have microstructure with plated-like grains aligning in the direction parallel to the casting plane. The ceramics exhibit {h 0 0} preferred orientation and the degree of orientation is larger than 0.7. The degree of grain orientation increases with the increasing sintering temperature. The textured ceramics show anisotropy dielectric and piezoelectric properties in the directions of parallel and perpendicular to the casting plane. The ceramics in the perpendicular direction exhibit better dielectric and piezoelectric properties than those of the nontextured ceramics with the same composition. The optimized sintering temperature is 1150 °C where the maximum d₃₃ of 134 pC/N parallel to casting plane, the maximum k₃₁ of 0.31, and the maximum Q_m of 154 in perpendicular direction were obtained.     

Simultaneously enhanced piezoelectric response and piezoelectric voltage coefficient in textured KNN‐based ceramics

<001> ‐textured 0.99(K_0.49Na_0.49Li_0.02)(Nb_0.97‐xSb_0.03Ta_x)O₃‐0.01CaZrO₃ [abbreviated as 0.99KNLN_0.97‐xST_x‐0.01CZ, x = 0.03, 0.07, 0.10, 0.15, 0.20, 0.25] ceramics were prepared by templated grain growth (TGG) method and a two‐step sintering process. Giant longitudinal piezoelectric coefficient d₃₃ (391 pC/N) and piezoelectric strain coefficient d₃₃* (630 pm/V under an AC E‐field of 20 kV/cm) can be obtained in the textured ceramics with x = 0.25. All textured ceramics display superior k_p (>54%) and g₃₃ (>23 × 10^?3 Vm/N) which are in an order of magnitude with PZT ceramics. The maximum value of k_p (~63.3%) obtained in textured ceramics with x = 0.15 is higher than that of famous textured LF4 ceramics. Excellent comprehensive properties suggest that <001> ‐textured 0.99KNLN_0.97‐xST_x‐0.01CZ ceramics are promising candidates in the field of lead‐free piezoelectric materials.     

3D printing orientation controlled PMN-PT piezoelectric ceramics

Piezoelectric textured ceramics have drawn increasing research and industry interests by balancing the production cost and material performances. A new approach to realize the texture in piezoelectric ceramics is developed based on 3D printing stereolithography (SL) technique and successfully applied in the preparation of < 001 > -textured 0.71(Sm_0.01Pb_0.985)(Mg_1/3Nb_2/3)O₃-0.29(Sm_0.01Pb_0.985)TiO₃ (1 %Sm-PMN-29PT) ceramics in this work. As a critical process in texture ceramic fabrication, the alignment of BaTiO₃ templates along the horizontal direction is achieved by the shear force produced from the relative motion between the resin container and the blade during SL. The textured ceramics with obvious grain orientation features are successfully obtained. The enhanced piezoelectric properties of d₃₃ ≈ 652 pC N^?1 and d₃₃* ≈ 800 pm V^?1 are achieved in the 3D printed textured ceramic, which are about 60 % and 40 %, respectively, higher than their non-textured counterparts. Moreover, the textured sample shows a significant improvement on thermal stability of d₃₃*_T, which varies by less than ± 6 % from RT to 110 °C. Furthermore, the introduction of 3D printing into the synthesis of textured piezoelectric ceramics shows great advantages over the traditional tape-casting method. This work is expected to provide a promising way for the future design of textured piezoelectric functional materials.     

Grain-orientation-engineered PMN-10PT ceramics for electrocaloric applications

The electrical properties of ferroelectric materials depend on their crystal orientations. The 〈001〉 and 〈111〉 textured 0.90Pb(Mg_1/3Nb_2/3)O₃–0.10PbTiO₃ (PMN-10PT) ceramics were synthesized using a template grain growth method and conventional solid sintering process. The Lotgering factors of the 〈001〉 and 〈111〉 textured PMN-10PT ceramics with 5% anisotropic BaTiO₃ (BT) precursors were 95% and 87%, respectively. The influence of grain orientation direction on dielectric properties was investigated, revealing that the permittivity of textured PMN-10PT ceramics (ε_r〈001〉 = 12200, ε_r〈111〉 = 11800) was lower than that of random ceramics (ε_r = 18700). Electrocaloric (EC) responses of the random and textured samples were analyzed using an indirect polarization-deduced method based on Maxwell's equations. When the applied field was 50 kV cm⁻¹, the 〈111〉 textured ceramics exhibited an enhanced adiabatic temperature change of 1.30 K, which was 20% higher than that of the random samples. In addition, the EC performance of the 〈111〉 oriented samples was significantly improved compared to that of the 〈001〉 oriented ones. This work characterizes the grain-orientation-dependent EC responses in the PMN-PT system, which would be a promising approach to EC response improvement in ferroelectric ceramics.     

Large electric field induced strain of Bi(Mg1/2Ti1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 ceramics textured by Template Grain Growth

<001> oriented xBi(Mg_1/2Ti_1/2)O₃-(0.7-x)Pb(Mg_1/3Nb_2/3)O₃-0.3PbTiO₃ (BMT-PMN-PT) textured ceramics are successfully fabricated by the template grain growth method using BaTiO₃ platelets as template. BMT-PMN-PT textured ceramics with different BMT contents are studied in terms of crystal structure, microstructures, dielectric and ferroelectric properties, and electric field induced strain. The as-fabricated BMT-PMN-PT textured ceramics were found to have a strong orientation along <001> direction. The frequency dispersion of dielectric constant of BMT-PMN-PT textured ceramics increases gradually and its relaxability becomes stronger with increasing BMT content. A large electric-field induced strain (0.42 % at 4 kV/mm) is obtained in 0.25BMT-0.45PMN-0.3PT textured ceramics with Lotgering factor 0.94, which is about 83 % enhancement than that of the randomly oriented ceramics (0.23 % at 4 kV/mm). The strain of 0.25BMT-0.45PMN-0.3PT textured ceramics have a relatively high thermal stability, with a slight decrease from 0.42 % to 0.28 % in the temperature range of 20−100 °C. Our research suggests that 0.25BMT-0.45PMN-0.3PT textured ceramics have a greatly potential for actuator devices applications owing to its advantages of large electric field induced strain response.     

Grain orientation evolution and multi-scale interfaces enhanced thermoelectric properties of textured Sr0.9La0.1TiO3 based ceramics

Sr_0.9La_0.1TiO₃ based textured ceramics (SLTT-S3T) with a texture fraction of 0.81 are successfully fabricated by the reactive template grain growth method, in which Sr_0.9La_0.1TiO₃/20 wt%Ti was used as matrix and 10 wt% plate-like Sr₃Ti₂O₇ template seeds were used as templates. The phase transition, microstructure evolution, and the anisotropic thermoelectric properties of SLTT-S3T ceramics were investigated. The results show that the ceramics are mainly composed of Sr_0.9La_0.1TiO₃ and rutile TiO₂ phases. Grains grow with a preferred orientation along (h00). A maximum ZT of 0.26 at 1073 K was achieved in the direction perpendicular to the tape casting direction. The low lattice thermal conductivity of 1.9 W/(m K) at 1073 K was obtained decreased by 34%, 40%, and 38% compared with non-textured, SrTiO₃ and Sr_0.9La_0.1TiO₃ ceramics prepared by the same process, can be attributed to the enhanced phonon scattering by the complex multi-scale boundaries and interfaces. This work provides a strategy of microstructural design for thermoelectric oxides to decrease intrinsic lattice thermal conductivity and further regulate thermoelectric properties via texture engineering.     

A quasi-linear piezoelectric strain behavior of [001] textured rhombohedral PMN–24%PT ceramic

Highly textured (1–x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃ (PMN–xPT) piezoelectric ceramics were fabricated. It was found that [001] textured rhombohedral PMN–24%PT ceramic exhibited a quasi-linear piezoelectric strain behavior with low hysteresis. The strain hysteresis of PMN–24%PT ceramic was reduced from 22.5% to 9% at 30 kV/cm using the texture method. Accurate displacement was generated by DC field using textured PMN–24%PT ceramic. The domain configurations in textured PMN–xPT ceramics were figured out using the chemical etching method. It was demonstrated that the quasi-linear and low-hysteretic strain behavior was due to a fixed domain configuration. We predict that the textured PMN–24%PT ceramic will facilitate the development of low-voltage driving piezoelectric actuators with high precision.     

Texture and Anisotropy in Silicon Nitride

In this investigation quantitative texture analysis, including calculation of the orientation distribution function, is used to demonstrate the degree of preferred orientation in β -Si₃N₄ which has been hot-pressed or hot-worked. The results indicate that plane strain compression can produce strong textures. The texture is decided by the processing parameters including temperature, sintering additives, and stress state. Grain rotation and preferred grain growth apparently both contribute to texture development in β -Si₃N₄. Basal (00 l ) pole figures obtained from the orientation distribution function are consistent with microstructural observations and are reflected in indentation fracture toughness anisotropy. In plane strain the ratio of maximum to minimum fracture toughness is greater than 2.     

Texture and Anisotropy of Polycrystalline Piezoelectrics

Piezoelectricity is manifested in ferroelectric ceramics by inducing a preferred volume fraction of one ferroelectric domain variant orientation at the expense of degenerate orientations. The piezoelectric effect is therefore largely controlled by the effectiveness of the electrical poling in producing a bias in ferroelectric (180°) and ferroelastic (non-180°) domain orientations. Further enhancement of the piezoelectric effect in bulk ceramics can be accomplished by inducing preferred orientation through grain-orientation processes such as hot forging or tape casting that precede the electrical-poling process. Coupled crystal orientation and domain orientation processing yields ceramics with an even greater piezoelectric response. In this paper, preferred orientations of domains and grains in polycrystalline piezoelectric ceramics generated through both domain- and grain-orientation processing are characterized through pole figures and orientation distribution functions obtained using data from a variety of diffraction techniques. The processing methods used to produce these materials and the methods used to evaluate preferred orientation and texture are described and discussed in the context of prior research. Different sample and crystal symmetries are explored across a range of commercial and laboratory-prepared materials. Some of the variables presented in this work include the effects of in situ thermal depoling and the detailed processing parameters used in tape casting of materials with preferred crystallite orientations. Preferred orientation is also correlated with anisotropic properties, demonstrating a clear influence of both grain and domain orientations on piezoelectricity.     

Achieving both high electromechanical properties and temperature stability in textured PMN-PT ceramics

Textured piezoelectric ceramics, such as textured Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (PMN-PT) ceramics, have attracted considerable attention from both academia and industry, as they possess crystal-like piezoelectric properties, high composition homogeneity, and low manufacturing cost. However, the main difficulty with the textured piezoelectric ceramics is the presence of BaTiO₃ (BT) templates, which greatly reduces their piezoelectricity and phase transition temperature. Thus, it is highly recommended to fabricate textured piezoelectric ceramics using as few templates as possible. Here, we successfully fabricated high-quality <001>-textured PMN-28PT ceramics (texturing degree of 99%) by using an extremely small amount of BT templates (1 vol.%) with the help of CuO/B₂O₃ sintering aids. The textured PMN-28PT ceramic exhibits 80% piezoelectric coefficient (d₃₃ ∼ 1200 pC/N), 96% electromechanical coefficient (k₃₃ ∼ 88%) and the same temperature stability (T_rt ∼ 100, T_c ∼ 150°C) when compared to its single crystal counterpart. In addition, by using an alternating current electric field poling (AC-poling), the piezoelectric coefficient d₃₃ and dielectric permittivity ε₃₃ of the textured PMN-28PT ceramics were further enhanced around 5–8%. It is believed that the advantages of high electromechanical properties, low cost, and easy mass production of textured PMN-28PT ceramic will make it a promising candidate for advanced electromechanical devices.     

Enhanced high-temperature strength in textured (Ti1/3Zr1/3Hf1/3)B2 medium-entropy ceramics via strong magnetic field

This study prepared textured (Ti_1/3Zr_1/3Hf_1/3)B₂ medium-entropy ceramics for the first time that maintain enhanced flexural strength up to 1800°C using single-phase (Ti_1/3Zr_1/3Hf_1/3)B₂ powders, slip casting under a strong magnetic field, and hot-pressed sintering methods. Effects of WC additive and strong magnetic field direction on the phase compositions, orientation degree, microstructure evolution, and high-temperature flexural strength of (Ti_1/3Zr_1/3Hf_1/3)B₂ were investigated. (Ti_1/3Zr_1/3Hf_1/3)B₂ grain grows along the a,b-axes, resulting in a platelet-like morphology. Pressure parallel and perpendicular to the magnetic field direction can promote the orientation degree and hinder the texture structure formation, respectively. Reaction products of W(B,C) and (Ti,Zr,Hf)C between (Ti_1/3Zr_1/3Hf_1/3)B₂ and WC additive can efficiently refine the (Ti_1/3Zr_1/3Hf_1/3)B₂ grain size and promote grain orientation. (Ti_1/3Zr_1/3Hf_1/3)B₂ ceramics doped with 5 vol.% WC yielded a Lotgering orientation factor of 0.74 through slip casting under a strong magnetic field (12 T) and hot-pressed sintering at 1900°C. Furthermore, cleaning the boundary by W(B,C) and introducing texture can enhance the grain-boundary strength and improve its high-temperature flexural strength. The four-point flexural strength of textured (Ti_1/3Zr_1/3Hf_1/3)B₂-5 vol.% WC ceramics was 770 ± 59 MPa at 1600°C and 638 ± 117 MPa at 1800°C.     

Giant electro-strain in textured Li+-doped 0.852BNT–0.11BKT–0.038BT ternary lead-free piezoelectric ceramics

Texturing is an effective approach to improving the piezoelectricity of piezoelectric ceramics. In this work, <001> textured Li⁺-doped 0.852Bi_0.5Na_0.5TiO₃–0.11Bi_0.5K_0.5TiO₃–0.038BaTiO₃ ternary lead-free piezoelectric ceramics are prepared by the reactive templates grain growth (RTGG) method. X-ray diffraction (XRD) results demonstrate a high orientation degree of 77% along the <001> direction. Outstanding electro-strain response, which is higher than most of reported BNT-based textured ceramics, is achieved due to the contribution of oriented-grains along the <001> direction. A large electro-strain of 0.55% with a relatively low hysteresis is obtained at 6.5 kV/mm with corresponding large signal piezoelectric coefficient () of 846 pm/V in the textured ceramics, which is 49% higher than that of the random ceramics. Besides, the electro-strain could reach as high as 0.52%@5.5 kV/mm ( = 945 pm/V) at 100°C. These results indicate that the RTGG is an effective way to design high performance lead-free piezoelectric materials.     

Investigation of the piezoelectric and anti-reduction properties of (Ba,Ca) (Ti,Sn, Hf) textured ceramics prepared under low oxygen partial pressure conditions at low sintering temperatures

Multilayer piezoelectric ceramics must be sintered in a reducing atmosphere, preventing oxidation of the inner base metal. Plate-like textured (Ba, Ca)(Ti, Sn, Hf)O₃ ceramics with a <001> preferred orientation were successfully developed at a low oxygen partial pressure (PO₂:10^?8 atm) using a BaTiO₃ (BT) template with sintering temperatures < 1300 °C, which is beneficial for multilayer applications using base metal co-firing with ceramics. When adding the 3 wt% BT template, the proposed samples had a Lottgering factor of 84 %, piezoelectric coefficients d₃₃ = 324 pC/N, -d₃₁ = 122 (pC/N), and Q_m = 452, and the strain values increased from 0.07 % for the randomly oriented ceramics to 0.115 % at 20 kV/cm for the textured ceramics, confirming that the texturing behavior assisted the grain growth and improved both the soft and hard behaviors and insulation resistance of the proposed lead-free ceramics. These findings make a significant contribution to the production of high-power piezoelectric components.     

Fabrication and electrical properties of textured (Na,K)0.5Bi0.5TiO3 ceramics by reactive-templated grain growth

Textured (Na_0.85K_0.15)_0.5Bi_0.5TiO₃ (NKBT) ceramics with a relative density of >94% were fabricated by reactive-templated grain growth. Plated-like Bi₄Ti₃O₁₂ template particles synthesized by the NaCl–KCl molten salt process were aligned by tape casting in a mixture of original oxide powders. The effect of sintering temperature on the grain orientation and electrical properties of textured NKBT ceramics were investigated. The results show that the textured ceramics have a microstructure with plated-like grains aligning in the direction parallel to the casting plane. The degree of grain orientation increased at increasing sintering temperature. The textured ceramics show anisotropic electrical properties in the directions parallel and perpendicular to the casting plane. The dielectric constant parallel to {h 0 0} plane is three times higher than that of the perpendicular direction in textured NKBT ceramics. The optimized sintering temperature is 1150 °C where the maximum dielectric constant is 2041, the remnant polarization is 68.7 μC/cm², the electromechanical coupling factor (k₃₁) and the piezoelectric constant (d₃₃) amount to 0.31 and 134 pC/N, respectively.     

Grain-orientated lead-free BNT-based piezoceramics with giant electrostrictive effect

In this study, we propose an effective approach to gain prominent electrostrictive behavior by taking advantage of texture construction in lead-free (Bi_0.5Na_0.5)TiO₃(BNT)-based piezoceramics for actuator applications. The electrostrictive effect was explored systematically in <00 l> textured 0.90(0.83Bi_0.5Na_0.5TiO_3-0.17Bi_0.5K_0.5TiO₃)-0.10NaNbO₃(BNT-BKT-NN) ceramics with respect to grain orientation, temperature and electric fields. It was found that the electrostrctive coefficient Q₃₃ and recoverable strain increase monotonously with the grain orientation increasing. At the optimized microstructure (F_00 l=92%), a giant Q₃₃ with nearly purely electrostrictive characteristics was detected to be around ~0.0354 m⁴C⁻², which was far larger than the reported values of Pb(Mg_1/3Nb_2/3)O₃ (PMN) and the existing BNT-based electrostrictive materials. Meanwhile, the acquired Q₃₃ was found to exhibit excellent stability for the highly textured sample under different temperature or electric field conditions. Our achievement demonstrates that the giant electrostrictive properties with superior temperature and electric field stability for <00 l> textured BNT-BKT-NN ceramic are of great significance in replacing traditional PMN ceramics for actuator applications.     

Templated Grain Growth of <001> Textured PMN-28PT Using SrTiO3 Templates

Highly textured PMN-28PT (0.72Pb(Mg_1/3Nb_2/3)O₃–0.28PbTiO₃) ceramics were produced by templated grain growth on <001> oriented platelet-shaped SrTiO₃ template particles with an aspect ratio of 10–15. The templates were aligned in PMN-28PT matrix powder via tape casting and fired in an O₂–PbO atmosphere at 1150°C for up to 15 h. This resulted in textured ceramics with a 40 micrometer grain size and without residual templates. The volume fraction of textured material (  f  ) and the orientation parameter ( r ) were quantified by fitting X-ray diffraction rocking curve data to the March–Dollase equation. Processing conditions were optimized to achieve the best possible values of f and r for the chosen templates and matrix powder. A texture fraction of at least 81 vol% and an orientation parameter of 0.2 were achieved when all random matrix grains were consumed (a perfect textured ceramic would show a texture fraction of 100 vol% and an orientation parameter of 0).     

Structure and electrical properties of Ca2+-doped (Na0.47Bi0.47Ba0.06)TiO3 lead-free piezoelectric ceramics

The lead-free piezoelectric ceramics (Na_.47Bi_.47Ba_.06)_1-xCa_xTiO₃ (x?=?0, 0.01, 0.02, 0.03, 0.05, and 0.08, abbreviated as BNBTC/0, BNBTC/1, BNBTC/2, BNBTC/3, BNBTC/5, and BNBTC/8, respectively) were obtained using the solid-state reaction method. The structure, electric conductivity, and dielectric, ferroelectric, and piezoelectric properties of the Ca²⁺-doped (Na_.47Bi_.47Ba_.06)TiO₃ ceramics were thoroughly investigated. The ceramics sintered at 1200?°C exhibit dense microstructures, having relative densities higher than 96%. The X-ray diffraction results demonstrate that all ceramics have a pure perovskite structure. The mean grain sizes of the ceramics are related to the Ca²⁺ quantity. A small quantity of Ca²⁺ ions (x?≤?0.03) improves the piezoelectric and ferroelectric properties of the samples. The dielectric behavior of the samples is sensitive to the Ca²⁺ content and electric poling. The results demonstrate that the electrical properties of the (Na_.47Bi_.47Ba_.06)TiO₃ lead-free ceramics can be well tuned by varying the Ca²⁺ quantity.     

Achieving large piezoelectric response and ultrahigh electrostriction in [001] textured BiScO3-PbTiO3 high-temperature piezoelectric ceramics

[001] textured 0.40BiScO₃-0.60PbTiO₃-0.125 mol%Nb⁵⁺ (BS-60PT-0.125Nb) high-temperature piezoelectric ceramics were synthesized using templated grain growth process. A high texture degree F₀₀₁ of 99% was obtained using 2 vol% BaTiO₃ (BT) templates. The piezoelectric charge constant d₃₃ and the unipolar strain under 40 kV cm⁻¹ at room temperature for the textured ceramics are 646 pC N⁻¹ and 0.36%, respectively, which is over two times as those for untextured ceramics (∼243 pC N⁻¹ and 0.17%). The electrostriction Q₃₃ value of the textured sample remarkably increased from 0.034 m⁴ C⁻² to 0.068 m⁴ C⁻² under 30 kV cm⁻¹, showing a twice higher than untextured. Compared with random ceramics, the improvement piezoelectric response of the textured ceramics is primarily attributed to the increase of the dielectric constant ε_r and electrostriction coefficient Q₃₃ along [001] orientation, which is originating from the anisotropy of piezoelectricity. The BS-60PT-0.125Nb textured ceramics have large piezoelectric response and ultrahigh electrostriction with high temperature stability (high depolarization temperature T_d of ∼360°C and high Curie temperature T_c of 421°C), showing great potential for the piezoelectric applications at high temperatures.