Fabrication of SiC ceramic architectures using stereolithography combined with precursor infiltration and pyrolysis

Stereolithography based additive manufacturing provides a new route to produce ceramic architectures with complex geometries. In this study, 3D structured SiC ceramic architectures were fabricated by stereolithography based additive manufacturing combined with precursor infiltration and pyrolysis (PIP). Firstly, photosensitive SiC slurry was prepared. Then, stereolithography was conducted to fabricate complex-shaped green SiC parts. Polymer burn-out was subsequently performed, and porous SiC preforms were produced. After that, precursor infiltration and pyrolysis was used to improve the density and strength. Finally, 3D-structured SiC ceramic architectures with high accuracy and quality were obtained. It is believed that this study can give some fundamental understanding for the additive manufacturing of SiC ceramic structures.     

Additive manufacturing of silicon nitride ceramics: A review of advances and perspectives

Silicon nitride (Si₃N₄) ceramic has been widely applied in various engineering fields. The emergence of additive manufacturing (AM) technologies provides an innovative approach for the fabrication of complex-shaped Si₃N₄ ceramic components. This article systematically reviews the advances of the AM of Si₃N₄ ceramic in recent years and forecasts the potential perspectives in this field. This review aims to motivate future research and development for the AM of Si₃N₄ ceramic.     

3D-printing of polymer‐derived SiCN ceramic matrix composites by digital light processing

In this study, we present a DLP 3D-printing strategy for the fabrication of SiCN ceramic matrix composites (CMCs). The polysilazane-based preceramic polymer containing inert fillers was UV-cured into a green body and then converted to SiCN CMCs after pyrolysis. The introduced fillers (Si₃N₄ particles and Si₃N₄ whiskers) as reinforcements are well dispersed in the matrix, which can not only effectively reduce the linear shrinkage and weight loss, but also greatly improve the mechanical properties of the SiCN CMCs. The bending strength of the SiCN CMCs reinforced with 10 wt% Si₃N₄ whiskers (without surface polished) reached 180.7 ± 15.6 MPa. Furthermore, the effect of fillers content on microstructure and porosity of the SiCN CMCs are discussed, and it was found that the excessive fillers led to increased pore defects and decreased continuity of the matrix, thereby reducing the mechanical properties of the SiCN CMCs. This strategy provides a promising ceramic manufacturing technique to fabricate polymer‐derived CMCs with complex-shaped and high-performance for potential demanding applications.     

New observations on wear characteristics of solid Al2O3/Si3N4 ceramic tool in high speed milling of additive manufactured Ti6Al4V

Additive Manufacturing (AM) technologies applied to the titanium alloys have attracted attention from industries in recent years. Despite one of the main goals of AM is the reduction of manufacturing steps, semi-finish/finish machining operations are still required so as to obtain the desired geometrical tolerance and surface features. In this study, the solid end mill was manufactured by Al₂O₃/Si₃N₄ (Sialon) ceramic materials and employed in high-speed slot milling of Ti6Al4V alloy fabricated by the Direct Metal Laser Sintering (DMLS) AM technology to study the tool wear characteristics during processing. The Raman spectroscopic method was employed to characterize the molecular structures of Sialon ceramics for the manufacturing of the cutting tool. The morphologies and elemental maps of wear region of the ceramic tool were examined by scanning electron microscope and energy dispersive spectroscopy techniques. The results show that the adhesion wear and diffusion wear are the dominant wear mechanisms, and the chemical stability of Al₂O₃/Si₃N₄ (Sialon) ceramics fabricated as the solid ceramic tool to the attack of the atoms from additive manufactured Ti6Al4V is relatively weak under the atmosphere. The difference of thermal expansion coefficients of diffusion layer and tool substrate accelerates the initiation and propagation of thermal cracks formed on the diffusion interface. Moreover, fracturing and crater-like groves near the tool edge were finally formed due to the removal of adhered workpiece material.     

3D printing of honeycomb Si3N4 ceramic

In this paper, a honeycomb Si₃N₄ ceramic was fabricated by 3D printing with a well-preserved structure. The effects of Si₃N₄ content on the rheological properties of Si₃N₄/sol–silica ink and the printing resolution of products were investigated. The microstructure, phase composition, liner shrinkage rate, and fracture behavior of printed samples before and after sintering were systematically characterized in detail. The results showed that the modified inks had the optimized rheological properties, and the stress–shear rate curves corresponding to each slurry could be well described by Bingham and Herschel–Bulkley fluid models. The corresponding slump rates of the printed samples with different Si₃N₄ to sol–silica mass ratios were all lower than 4%, and the linear shrinkage rate of all of the samples after sintering was below 20%. The fracture behavior under compressive loading of the honeycomb Si₃N₄ ceramics tended to be non-catastrophic fractures both before and after sintering. The compressive strengths of all of the printed samples decreased with the increase of the Si₃N₄ content, and the highest compressive strength of the honeycomb ceramics could reach 131.2 MPa after sintering at 1600°C, which was about 366.9% higher than that of the samples in green state prior to the sintering.     

Effects of particle size and color on photocuring performance of Si3N4 ceramic slurry by stereolithography

Due to high absorbance of UV light and low solid loading, the stereolithography-based additive manufacturing of gray-colored and dense Si₃N₄ ceramic is of significant difficulty and challenge. The effects of geometric properties of ceramic powders on the curing performance were investigated by studying the absorption difference of the Si₃N₄ ceramic particles with different colors and particle sizes and ultraviolet light. The results show that the transmission of ultraviolet light and curing performance of the darker Si₃N₄ ceramic slurry are much poor. Under the same particle size, the Si₃N₄ ceramic slurry using lighter particles presents the smaller scattering coefficient. The scattering coefficient (～202) of the gray powder with ～0.8 μm average particle size is the smallest. Under the same color, the larger the particle size, the smaller the scattering coefficient. The smallest scattering coefficient of the white powder with ～2.0 μm average particle size is ～110.     

Effect of polystyrene addition on properties of porous Si3N4 ceramics fabricated by digital light processing

Porous Si₃N₄ ceramics with high strength and high transmittance have been widely used in the field of defense and military. Additive manufacturing (AM) technology is one of the effective means to fabricate porous Si₃N₄ ceramics. Nevertheless, it is difficult to prepare porous Si₃N₄ ceramics by using digital light processing (DLP) because of the large refractive index difference between Si₃N₄ powders and photosensitive resin. In this study, the effects of the amount of polystyrene (PS) powders on the properties of Si₃N₄ ceramic slurries and sintered ceramics were systematically discussed. The addition of PS reduced the overall refractive index of powders and increased the average particle size of powders, thus improving the cure depth of Si₃N₄ ceramic slurries from 11.0 ± 2.0 μm to 55.7 ± 1.8 μm. With the increase of PS content, the shrinkage and porosity of Si₃N₄ ceramics gradually increased, and the bulk density and flexural strength showed the opposite trend. The slurry with low viscosity (2.38 Pa٠s at a shear rate of 30 s⁻¹) and high cure depth (51.2 ± 4.6 μm) was obtained when the content of PS was 15 wt%, which met the thickness requirements for printing. The total porosity of Si₃N₄ ceramics reached the maximum values at 28.21 ± 2.58%. The addition of PS solved the problem of low cure depth of slurries, and PS as a pore-forming agent could help Si₃N₄ ceramics form porous structure. This research provides valuable insights into the fabrication of non-oxide ceramics with high refractive index using DLP technology.     

Research on the effects of surface modification of ceramic powder on cure performance during digital light processing (DLP)

Digital light processing (DLP) is one of the most important additive manufacture technologies to fabricate ceramic parts with complex geometries. Compared with pure photosensitive resin, the cure performance of ceramic suspensions is obviously different due to the optical property change after the addition of ceramic powders. In this paper, a unique oxidation process was used to modify the optical properties of nitride powders including AlN and Si₃N₄. The properties of oxidized ceramics were investigated and the cure performance of ceramic suspensions was then characterized. The effect of oxidation time on cure performance was evaluated. The results showed that for AlN, oxidation process leads to the smaller cure depth and smaller excess cure width as compared with non-oxidized AlN and for Si₃N₄, oxidation process leads to the larger cure depth and larger excess cure width as compared with non-oxidized Si₃N₄, indicating that both refractive index and light absorbance of ceramic powders have obvious effects on cure behaviors. Additionally, the cure behavior of oxidized ceramic suspension in this study shows that the relationship of cure depth vs. incident energy agrees well with Beer- Lambert model, but the excess cure width vs. incident energy is not consistent with quasi Beer-Lambert model due to the nature of digital micromirror device (DMD).     

Preparation of broadband transparent Si3N4-SiO2 ceramics by digital light processing (DLP) 3D printing technology

Wave-transmitting materials are a kind of multi-functional materials that protect the normal operation of communication and guidance systems of spacecraft in harsh environments. In this paper, we fabricate a broadband microwave transparent Si₃N₄-SiO₂ composite ceramic with excellent performance through digital light processing (DLP) 3D printing technology. The influences of sintering temperature on the weight increase rate, density, dimensional shrinkage, phase composition, microstructure, bending strength and dielectric properties of Si₃N₄-SiO₂ ceramic were all systematically studied. The strength of Si₃N₄-SiO₂ ceramic sintered at 1350 ℃ was 77 ± 5 MPa. The relative permittivity of the ceramic is within the range of less than 4, and the loss tangent can be below 0.003. The 3D printed Si₃N₄-SiO₂ ceramic material exhibited excellent wave-transparent performance.     

Influence of the content of polymethyl methacrylate on the properties of porous Si3N4 ceramics fabricated by digital light processing

Porous Si₃N₄ ceramics are highly regarded as ideal materials for radomes due to their unique characteristics. However, the slurry used for the preparation of porous Si₃N₄ ceramics suffers from a low cure depth, making it challenging to fabricate ceramic components using DLP technology. In this study, porous Si₃N₄ ceramics were prepared by combining DLP technology with pore-forming agent method. The addition of polymethyl methacrylate (PMMA) powders with lower refractive index than that of Si₃N₄ powders can improve the penetration depth of ultraviolet light in the Si₃N₄ slurry. A systematic study was conducted to investigate the influence of the addition of PMMA powders on the properties of Si₃N₄ slurries and porous Si₃N₄ ceramics. When PMMA powders were added at 10 wt%, the slurry with a lowest viscosity of 0.13 Pa s (the shear rate is 30 s⁻¹) and cure depth of 40.0 μm (the exposure energy is 600 mJ/cm²) was obtained. With the increase of PMMA content, porous Si₃N₄ ceramics experienced a gradual decrease in both the flexural strength and bulk density, while the porosity increased from 14.41% to 27.62%. Specifically, when 20 wt% PMMA was added, the resulting porous Si₃N₄ ceramics had a lowest bulk density (2.41 g/cm³), a maximum porosity (27.62%), and a flexural strength (435.87 MPa). The study is of great significance in establishing an experimental foundation for fabricating porous Si₃N₄ ceramics by using DLP technology.     

Preparation of Si3N4 ceramic based on digital light processing 3D printing and precursor infiltration and pyrolysis

The emergence of digital light processing (DLP) 3D printing technology creates favorable conditions for the preparation of complex structure silicon nitride (Si₃N₄) ceramics. However, the introduction of photosensitive resin also makes the Si₃N₄ ceramics prepared by 3D printing have low density and poor mechanical properties. In this study, high-density Si₃N₄ ceramics were prepared at low temperatures by combining DLP 3D printing with precursor infiltration and pyrolysis (PIP). The Si₃N₄ photocurable slurry with high solid content and high stability was prepared based on the optimal design of slurry components. Si₃N₄ green parts were successfully printed and formed by setting appropriate printing parameters. The debinding process of printed green parts was further studied, and the results showed that samples without defects and obvious deformation can be obtained by setting the heating rate at .1°C/min. The effect of the PIP cycle on the microstructure and mechanical properties of the Si₃N₄ ceramics was studied. The experimental results showed that the mass change and open porosity of the samples tended to be stable after eight PIP cycles, and the open porosity, density, and bending strength of the Si₃N₄ ceramics were 1.30% (reduced by 97%), 2.64 g/cm³ (increased by 43.5%), and 162.35 MPa.     

Low-temperature densification by plasma activated sintering of Mg2Si-added Si3N4

In this study, highly dense Si₃N₄ ceramics with excellent mechanical properties were fabricated using Mg₂Si as a sintering additive by plasma-activated sintering at 1400–1500 °C. The effects of the sintering temperature and content of Mg₂Si on the densification, microstructures, and mechanical properties of the Si₃N₄ ceramics were investigated. The mechanism responsible for the effect of Mg₂Si in the promotion of the sinterability of Si₃N₄ is discussed. The results showed that the addition of Mg₂Si could effectively remove the oxide layers on the Si₃N₄ particles and form a liquid phase during the sintering, promoting the densification and phase transition of the Si₃N₄ ceramics. The Si₃N₄ ceramic sintered at 1450 °C with 6.0 wt% of Mg₂Si exhibited the maximum strength of 1050 MPa.     

Sintered silicon nitride/nano-silicon carbide materials based on preceramic polymers and ceramic powder

A flexible method is presented, which enables the fabrication of porous as well as dense Si₃N₄/nano-SiC components by using Si₃N₄ powder and a preceramic polymer (polycarbosilazane) as alternative ceramic forming binder. The SiCN polymer benefits consolidation as well as shaping of the green body and partially fills the interstices between the Si₃N₄ particles. Cross-linking of the precursor at 300 °C increases the mechanical stability of the green bodies and facilitates near net shape machining. At first, pyrolysis leads to porous ceramic bodies. Finally, subsequent gas pressure sintering results in dense Si₃N₄/nano-SiC ceramics. Due to the high ceramic yield of the polycarbosilazane binder, the shrinkage during sintering is significantly reduced from 20 to 15 lin.%. Investigations of the sintered ceramics reveal, that the microstructure of the Si₃N₄ ceramic contains approx. 6 vol.% nano-scaled SiC segregations, which are located both at the grain boundaries and as inclusions in the Si₃N₄ grains.     

Stereolithographical fabrication of dense Si3N4 ceramics by slurry optimization and pressure sintering

Photocurable gray-colored Si₃N₄ ceramic slurry with high solid loading, suitable viscosity and high curing depth is critical to fabricate dense ceramic parts with complex shape and high surface precision by stereolithography technology. In the present study, Si₃N₄ ceramic slurry with suitable viscosity, high solid loading (45 vol %) and curing depth of 50 μm was prepared successfully when surface modifier KH560 (1 wt%) and dispersant Darvan (1 wt%) were used. The slurry exhibits the shear thinning behavior. Based on the Beer-Lambert formula, D_p (the attenuation length) and E_c (the critical energy dose) of Si₃N₄ ceramic slurry with solid loading of 45 vol % were derived as 0.032 mm and 0.177 mJ/mm², respectively. Si₃N₄ ceramic green parts with complex shape and high surface precision were successfully fabricated by stereolithography technology. After optimizing the debinding and sintering process for green parts, dense Si₃N₄ ceramics with 3.28 g/cm³ sintering density were fabricated. The microhardness and fracture toughness of as-sintered Si₃N₄ ceramics are ~14.63 GPa and ~5.82 MPa m^1/2, respectively, which are comparable to those of the samples by traditional dry-pressed and pressureless sintering technology. These results show that ceramic stereolithography technology could be promising to fabricate high performance ceramics, especially for gray-colored monolithic Si₃N₄ ceramics.     

Influence of the ratio of sintering aids on the properties of porous Si3N4 ceramics fabricated by digital light processing

The sintering aids play an important role in affecting the properties of porous Si₃N₄ ceramics. However, there are few researches on the properties of porous Si₃N₄ ceramics fabricated by digital light processing (DLP) with different ratios of sintering aids. In this paper, porous Si₃N₄ ceramics with different ratios of sintering aids (Y₂O₃-Al₂O₃) were formed by DLP technology. The influence of Y₂O₃-Al₂O₃ ratios on the properties of Si₃N₄ slurry and porous ceramic was studied systematically. The ratio of Y₂O₃-Al₂O₃ had little effect on the rheology and cure depth of Si₃N₄ slurry due to the low addition of sintering aids. The increase of Y₂O₃-Al₂O₃ ratio promoted the anisotropic growth of β-Si₃N₄. When the ratio of Y₂O₃-Al₂O₃ was 9:1, the aspect ratio of β grains reached the maximum. As the ratio of Y₂O₃-Al₂O₃ powders increased, the linear shrinkage of porous Si₃N₄ ceramics showed an increasing and then decreasing trend in three directions. When the Y₂O₃-Al₂O₃ ratio was 3:7, the shrinkage rate in the length, width and height direction reached the maximum (27.03%, 30.27% and 40.02%, respectively). The bulk density and flexural strength exhibited an initial increase followed by a subsequent decrease, while the porosity showed the opposite trend. When the Y₂O₃-Al₂O₃ ratio was 9:1, the porosity reached a maximum of 28.1%. And the bulk density and flexural strength were 2.42 g/cm³ and 421.58 MPa, respectively. This study is of great significance as it lays the experimental foundation in the performance control of porous Si₃N₄ ceramics fabricated by DLP.     

A novel method of strong and tough Si3N4 ceramic from the particle-stabilized foam

The brittleness of Si₃N₄ ceramics has always limited its wide application. In this paper, Si₃N₄ ceramics were prepared based on foam. Combining the unique honeycomb structure of the ceramic foams and the self-toughening mechanism of Si₃N₄, the strengthening and toughening of Si₃N₄ ceramics can be further achieved by adjusting the microstructure of Si₃N₄ ceramic foams. The powder particles are self-assembled by particle-stabilized foaming to form a foam body with a honeycomb structure. It was pretreated at different temperatures (1450–1750°C). The microstructure evolution of foamed ceramics at different pretreatment temperatures and the conversion rate of α-Si₃N₄ to β-Si₃N₄ at different pretreatment temperatures were explored. Then the foamed ceramics with different microstructures are hot-press sintered to prepare Si₃N₄ dense ceramics. The effects of different microstructures of foamed ceramics on the strength and toughness of Si₃N₄ ceramics were analyzed. The experimental results show that the relative density of Si₃N₄ ceramics prepared at a particle pretreatment temperature of 1500°C is 97.8%, and its flexural strength and fracture toughness are relatively the highest, which are 1089 ± 60 MPa and 12.9 ± 1.3 MPa m^1/2, respectively. Compared with the traditional powder hot-pressing sintering, the improvement is 21% and 33%, respectively. It is shown that this method of preparing Si₃N₄ ceramics based on foam has the potential to strengthen and toughen Si₃N₄ ceramics.     

High-purity stoichiometric Si3N4 ceramics through trimethylsilyl-substituted polysilazanes

Trimethylsilyl-substituted polysilazanes were designed and successfully synthesized. They were used to fabricate high-purity stoichiometric Si₃N₄ ceramics through pyrolysis process. Trimethylsilyl groups improved the stability of polysilazanes and easily escaped during pyrolysis, which effectively reduced oxygen and carbon content in the final polymer-derived Si₃N₄. The C content of Si₃N₄ ceramic was below 0.06 wt%, and the O content was below 1.2 wt%. The Si₃N₄ ceramics remained amorphous up to 1400°C, yet they were completely transformed into α-Si₃N₄ at 1500°C. Synergistic effect from low oxygen and carbon content contributed to highly stable amorphous state of Si₃N₄ till high temperatures. This amorphous Si₃N₄ ceramics could be used in cutting-edge technology where high purity is compulsory.     

Fabrication of Si3N4–SiBC composite ceramic and its excellent electromagnetic properties

To obtain better electromagnetic wave absorbing property, it is vitally necessary to develop novel ceramics with not only high dielectric loss but also low dielectric constant. Si₃N₄–SiBC, a composite ceramic with such dielectric properties, was fabricated by infiltrating SiBC into porous Si₃N₄ ceramic via low pressure chemical vapor infiltration. The high dielectric loss and the low dielectric constant are attributed to the unique microstructure of SiBC, which also leads to a very excellent wave-absorbing property of Si₃N₄–SiBC ceramic, attaining a minimal reflection coefficient of ?28 dB. Besides, the Si₃N₄–SiBC ceramic also shows a high mechanical property. Therefore, the Si₃N₄–SiBC ceramic exhibits great potential as an excellent functional and structural ceramic.     

Cutting performance improvement of Si3N4 ceramic cutting tools by adding boride

Cutting performances of silicon nitride (Si₃N₄) ceramic cutting tools with and without boride additive (2.5 vol% ZrB₂ or TiB₂) prepared by hot-pressing at 1500°C were investigated. Due to the α- to β-Si₃N₄ phase transformation and low densification temperature, boride-containing Si₃N₄ ceramics with high hardness and high toughness were obtained. The turning tests showed that the effective cutting lengths of the Si₃N₄–2.5 vol% TiB₂ ceramic (∼2480 m) and Si₃N₄–2.5 vol% ZrB₂ ceramic (∼2200 m) were higher than the monolithic Si₃N₄ ceramic (∼1780 m). As the toughness was improved while maintaining relative high hardness, the cutting performances of the boride-containing Si₃N₄-based inserts were improved by adding 2.5 vol% ZrB₂ or TiB₂. The improved cutting performance indicated that the boride-containing Si₃N₄ ceramics are expected to be used in the field of ceramic cutting tools.     

Experimental determination of residual stress in silicon nitride diffusion bonds obtained by high-energy X-ray diffraction

High resolution X-ray scanning diffractometry has been used to study the residual strain in binary metal/ceramic (Ni/Si₃N₄) and ceramic/ceramic (Si₃N₄/Ni thin film/Si₃N₄) diffusion bonds. Bonds were fabricated by simultaneous high temperature heating and uniaxial pressing. The axial and radial strain profiles have been determined along selected lines perpendicular to the bonding interface inside the ceramic bodies. The X-ray experiments have been done at the energy of 60 keV, which assured a very small absorption, and therefore, strain fields have been measured in the ceramic bulk. Strains showed higher values near the interface that decreased with the distance.