Dual material gate junctionless tunnel field effect transistor

This paper proposes a junctionless tunnel field effect transistor (JLTFET) with dual material gate (DMG) structure and the performance was studied on the basis of energy band profile modulation. The two-dimensional simulation was carried out to show the effect of conduction band minima on the abruptness of transition between the ON and OFF states, which results in low subthreshold slope (SS). Appropriate selection of work function for source and drain side gate metal of a double metal gate JLTFET can also significantly reduce the subthreshold slope (SS), OFF state leakage and hence gives improved I _ON/I _OFF.     

Performance estimation of sub-30 nm junctionless tunnel FET (JLTFET)

In this paper we examined the short channel behavior of junction less tunnel field effect transistor (JLTFET) and a comparison was made with the conventional MOSFET on the basis of variability of device parameter. The JLTFET is a heavily doped junctionless transistor which uses the concept of tunneling, by narrowing the barrier between source and channel of the device, to turn the device ON and OFF. The JLTFET exhibits an improved subthreshold slope (SS) of 24 mV/decade and drain-induced barrier lowering (DIBL) of 38 mV/V as compared to SS of 73 mV/decade and DIBL of 98 mV/V for the conventional MOSFET. The simulation result shows that the impact of length scaling on threshold voltage for JLTFET is very less as compared to MOSFET. Even a JLTFET with gate length of 10 nm has better SS than MOSFET with gate length of 25 nm, which enlightens the superior electrostatic integrity and better scalability of JLTFET over MOSFET.     

Impact of high-k spacer on device performance of a junctionless transistor

The impact of spacer dielectric on both sides of gate oxide on the device performance of a symmetric double-gate junctionless transistor (DGJLT) is reported for the first time. The digital and analog performance parameters of the device considered in this study are drain current (I _D ), ON-state to OFF-state current ratio (I _ON /I _OFF ), subthreshold slope (SS), drain induced barrier lowering (DIBL), intrinsic gain (G _m R _O ), output conductance (G _D ), transconductance/drain current ratio (G _m /I _D ) and unity gain cut-off frequency (f _T ). The effects of varying the spacer dielectric constant (k _sp ) on the electrical characteristics of the device are studied. It is observed that the use of a high-k dielectric as a spacer brings an improvement in the OFF-state current by more than one order of magnitude thereby making the device more scalable. However, the ON-state current is only marginally affected by increasing dielectric constant of spacer. The effects of spacer width (W _sp ) on device performance are also studied. ON-state current marginally decreases with spacer width.     

Heterogate junctionless tunnel field-effect transistor: future of low-power devices

Gate dielectric materials play a key role in device development and study for various applications. We illustrate herein the impact of hetero (high-k/low-k) gate dielectric materials on the ON-current (\(I_{\mathrm{ON}}\)) and OFF-current (\(I_{\mathrm{OFF}}\)) of the heterogate junctionless tunnel field-effect transistor (FET). The heterogate concept enables a wide range of gate materials for device study. This concept is derived from the well-known continuity of the displacement vector at the interface between low- and high-k gate dielectric materials. Application of high-k gate dielectric material improves the internal electric field in the device, resulting in lower tunneling width with high \(I_{\mathrm{ON}}\) and low \(I_{\mathrm{OFF}}\) current. The impact of work function variations and doping on device performance is also comprehensively investigated.     

Design and structural optimization of junctionless FinFET with Gaussian-doped channel

A junctionless (JL) fin field-effect transistor (FinFET) structure with a Gaussian doping distribution, named the Gaussian-channel junctionless FinFET, is presented. The structure has a nonuniform doping distribution across the device layer and is designed with the aim of improving the mobility degradation caused by random dopant fluctuations in JL FinFET devices. The proposed structure shows better performance in terms of ON-current (\(I_{\mathrm{ON}}\)), OFF-current (\(I_{\mathrm{OFF}}\)), ON-to-OFF current ratio (\(I_{\mathrm{ON}}{/}I_{\mathrm{OFF}}\)), subthreshold swing, and drain-induced barrier lowering. In addition, we optimized the structure of the proposed design in terms of doping profile, spacer width, gate dielectric material, and spacer dielectric material.     

Performance enhancement of recessed silicon channel double gate junctionless field-effect-transistor using TCAD tool

In this paper, we propose an n-type double gate junctionless field-effect-transistor using recessed silicon channel. The recessed silicon channel reduces the channel thickness between the underlap regions, results in lowering the number of charge carriers in the silicon channel, and therefore, diminishing the OFF-current in the device. The proposed device shows similar electrical characteristics with improved transconductance, as compared to the conventional double gate junctionless field-effect-transistor. The effect of channel length scaling on the performance have been investigated, and it has been found that the recessed junctionless device shows higher ON-to-OFF current ratio, lower subthreshold swing and better immunity against the short channel effects, namely threshold voltage roll-off and drain-induced-barrier-lowering. For a channel length of 20 nm the OFF-current of the order of 1.20?×?10^–14 A/µm, ON-to-OFF current ratio of the order of 6.01?×?10¹⁰, subthreshold swing of the value of 67 mV/dec, and DIBL of 37.8 mV V^?1 has been achieved with the proposed junctionless device, in comparison of conventional double gate junctionless FET. The performance of proposed device with respect to the variations in depth and length of recessed silicon area, has also been presented as a roadmap for further tuning of its electrical behaviour. Comparatively, steeper DC transfer characteristics and improved rail-to-rail swing in transient behaviour has been reported with the designed complementary metal–oxide–semiconductor inverter, based on recessed double gate junctionless FET. The proposed recessed silicon channel double gate junctionless field-effect-transistor has been simulated using TCAD tool.

     

Potential‐based threshold voltage and subthreshold swing models for junctionless double‐gate metal‐oxide‐semiconductor field‐effect transistor with dual‐material gate

On the basis of quasi‐two‐dimensional solution of Poisson's equation, an analytical threshold voltage model for junctionless dual‐material double‐gate (JLDMDG) metal‐oxide‐semiconductor field‐effect transistor (MOSFET) is developed for the first time. The advantages of JLDMDG MOSFET are proved by comparing the central electrostatic potential and electric field distribution with those of junctionless single‐material double‐gate (JLSMDG) MOSFET. The proposed model explicitly shows how the device parameters (such as the silicon thickness, oxide thickness, and doping concentration) affect the threshold voltage. In addition, the variations of threshold voltage roll‐off, drain‐induced barrier lowering (DIBL), and subthreshold swing with the channel length are investigated. It is proved that the device performance for JLDMDG MOSFET can be changed flexibly by adjusting the length ratios of control gate and screen gate. The model is verified by comparing its calculated results with those obtained from three‐dimensional numerical device simulator ISE. Copyright © 2015 John Wiley & Sons, Ltd.     

Junctionless MOSFETs with laterally graded-doping channel for analog/RF applications

In this paper, we propose a laterally graded-channel pseudo-junctionless (GPJL) MOSFET for analog/RF applications. We examine the dynamical performance of GPJL MOSFET and compare it with the common junctionless (JL) MOSFET architecture using a 2-D full-band electron Monte Carlo simulator (MC) with quantum correction. Our results indicate that the GPJL MOSFET outperforms the conventional JL MOSFET, yielding higher values of drain current (I _ds), transconductance (g _m), and cutoff frequency (f _t). Further, the emerging electric field and velocity distributions, as a consequence of the channel engineering introduced by the GPJL MOSFET, result in lower output conductance (g _ds) and higher early voltage (V _ea). The preeminence of the GPJL transistor over the JL transistor is further illustrated by showing improvements on the intrinsic voltage gain (A _vo) in the subthreshold regime, to as high as 61 %. These results indicate that our proposed GPJL MOSFET yields improvement in the analog/RF performance metrics as compared to JL MOSFETs.     

Device circuit co‐design to reduce gate leakage current in VLSI logic circuits in nano regime

In this paper, nanoscale metal–oxide–semiconductor field‐effect transistor (MOSFET) device circuit co‐design is presented with an aim to reduce the gate leakage curren t in VLSI logic circuits. Firstly, gate leakage current is modeled through high‐k spacer underlap MOSFET (HSU MOSFET). In this HSU MOSFET, inversion layer is induced in underlap region by the gate fringing field through high‐k dielectric (high‐k) spacer, and this inversion layer in the underlap region acts as extended source/drain region. The analytical model results are compared with the two‐dimensional Sentaurus device simulation. Good agreement is obtained between the model and Sentaurus simulation. It is observed that modified HSU MOSFET had improved off current, subthreshold slope, and drain‐induced barrier lowering characteristics. Further, modified HSU MOSFET is also analyzed for gate leakage in generic logic circuits. Copyright © 2015 John Wiley & Sons, Ltd.     

Impact of channel length,gate insulator thickness,gate insulator material,and temperature on the performance of nanoscale FETs

Aggressive technology scaling as per Moore’s law has led to elevated power dissipation levels owing to an exponential increase in subthreshold leakage power. Short channel effects (SCEs) due to channel length reduction, gate insulator thickness change, application of high-k gate insulator, and temperature change in a double-gate metal–oxide–semiconductor field-effect transistor (DG MOSFET) and carbon nanotube field-effect transistor (CNTFET) were investigated in this work. Computational simulations were performed to investigate SCEs, viz. the threshold voltage (V_th) roll-off, subthreshold swing (SS), and I_on/I_off ratio, in the DG MOSFET and CNTFET while reducing the channel length. The CNTFET showed better performance than the DG MOSFET, including near-zero SCEs due to its pure ballistic transport mechanism. We also examined the threshold voltage (V_th), subthreshold swing (SS), and I_on/I_off ratio of the DG MOSFET and CNTFET with varying gate insulator thickness, gate insulator material, and temperature. Finally, we handpicked almost similar parameters for both the CNTFET and DG MOSFET and carried out performance analysis based on the simulation results. Comparative analysis of the results showed that the CNTFET provides 47.8 times more I_on/I_off ratio than the DG MOSFET. Its better control over the threshold voltage, near-zero SCEs, high on-current, low leakage power consumption, and ability to operate at high temperature make the CNTFET a viable option for use in enhanced switching applications and low-voltage digital applications in nanoelectronics.     

A dopingless gate-all-around (GAA) gate-stacked nanowire FET with reduced parametric fluctuation effects

This paper proposes a gate-all-around silicon nanowire dopingless field-effect transistor (FET), utilizing a gate-stacked technique. The source and drain regions are formed by employing a charge plasma concept, with the application of appropriate work functions for metal contacts. The charge plasma approach reduces the need for doping control during fabrication, and thus reduces the thermal budget, while the gate-stacked structure solves the problem of scaling limitations with respect to the \(\hbox {SiO}_{2}\) dielectric thickness (< 2 nm). The simulation results show that the proposed device, when compared with a conventional junctionless nanowire FET (JL-NWFET), possesses enhanced performance parameters, with improved immunity to short-channel effects. The random dopant fluctuations (RDFs) of the proposed device are analyzed and compared with those of a conventional JL-NWFET. The conventional device has a high doping concentration, and as a result suffers from higher RDFs, whereas the proposed dopingless device possesses lower RDFs. The process parameters used to measure sensitivity to RDFs include the radius, doping concentration and gate oxide thickness. When the radius of the nanowire is varied by \(+\) 30%, changes in threshold voltage, on-state current and subthreshold slope of 66, 63 and 12%, respectively, are observed in the JL-NWFET, versus 5, 22.6 and 1.8% for the proposed dopingless device (CP-NWFET). Similar variations in doping concentration and gate oxide thickness are seen with the JL-NWFET, whereas the CP-NWFET is largely unaffected. Thus, the proposed gate-stacked dopingless CP-NWFET solves the issue of both doping control and scaling limitation of the gate oxide layer, which paves the way for easier fabrication, with exceptional immunity against parametric variations, making it a good candidate for future nanoscale devices.     

Investigation of trigate JLT with dual-<Emphasis Type="Italic">k</Emphasis> sidewall spacers for enhanced analog/RF FOMs

This paper shows the potential benefits of using the trigate junctionless transistor (JLT) with dual-k sidewall spacers to enhance analog/radio-frequency (RF) performance at 20-nm gate length. Simulation study shows that the source-side-only dual-k spacer (dual-kS) JLT can improve all analog/RF figures of merit (FOMs) compared with the conventional JLT structure. The dual-kS JLT shows improvement in intrinsic voltage gain (\(A_{V0}\)) by \(\sim \)44.58 %, unity-gain cutoff frequency (\(f_\mathrm{T}\)) by \(\sim \)7.67 %, and maximum oscillation frequency (\(f_\mathrm{MAX}\)) by \(\sim \)6.4 % at drain current \((I_\mathrm{ds}) = 10\,\upmu \hbox {A}/\upmu \hbox {m}\) compared with the conventional JLT structure. To justify the improvement in all analog/RF FOMs, it is also found that the dual-kS structure shows high electron velocity near the source region because of the presence of an additional electric field peak near the source region, resulting in increased electron transport efficiency and hence improved transconductance (\(g_\mathrm{m}\)). Furthermore, the dual-kS JLT shows a reduction in the electric field value near the drain end, thereby improving short-channel effects.     

A new F(ast)-CMS NEGF algorithm for efficient 3D simulations of switching characteristics enhancement in constricted tunnel barrier silicon nanowire MuGFETs

In this paper, we present 3D quantum simulations based on Non-Equilibrium Green’s Function (NEGF) formalism using the Comsol Multiphysics^? software and on the implementation of a new Fast Coupled Mode-Space (FCMS) approach. The FCMS algorithm allows one to simulate transport in nanostructures presenting discontinuities, as the normal Coupled Mode-Space (CMS) algorithm does, but with the speed of a Fast Uncoupled-Mode Space (FUMS) algorithm (a faster algorithm that cannot handle discontinuities). We then use this new algorithm to explore the effect of local constrictions on the performance of nanowire MultiGate Field-Effect Transistors (MuGFETs). We show that cross-section variations in a nanowire result in the formation of energy barriers that can be used to improve the on/off current ratio and switching characteristics of transistors: (1) A small constriction resulting in a barrier of the order of a 0.1 eV can be used as an effective means to improve the subthreshold slope and minimize the on/off current ratio degradation resulting from SD tunneling in ultra scaled transistor, and (2) We also report a new variable barrier transistor (VBT) device concept that is able to achieve sub-kT/q subthreshold slope without using impact ionization or band-to-band tunneling. Intra-band tunneling through constriction barriers is used instead. The device is, therefore, fully symmetrical and can operate at very low supply voltages. A subthreshold slope as low as 56.5 mV/decade is reported at T=300 K. The VBT reported here breaks the 60 mV/dec barrier over more than five decades of subthreshold current, which is the widest current range reported so far.     

Noise immune dielectric modulated dual trench transparent gate engineered MOSFET as a label free biosensor: proposal and investigation

We propose and investigate a biosensor based on a transparent dielectric-modulated dual-trench gate-engineered metal–oxide–semiconductor field-effect transistor (DM DT GE-MOSFET) for label-free detection of biomolecules with enhanced sensitivity and efficiency. Various sensing parameters such as the I_ON/I_OFF ratio and the threshold voltage shift are evaluated as metrics to validate the proposed sensing device. Additionally, S_Vth (the V_th sensitivity) is also analyzed, considering both positively and negatively charged biomolecules. In addition, radiofrequency (RF) sensing parameters such as the transconductance gain and the cutoff frequency are taken into account to provide further insight into the sensitivity of the proposed device. Furthermore, the linearity, distortion, and noise immunity of the device are evaluated to confirm the overall performance of the biosensor at high (GHz) frequency. The results indicate that the proposed biosensor exhibits a S_Vth value of 0.68 for positively charged biomolecules at a very low drain bias of 0.2 V. The proposed device can thus be used as an alternative to conventional FET-based biosensors.

     

Graded channel doping junctionless MOSFET: a potential high performance and low power leakage device for nanoelectronic applications

In this paper, a graded channel doping paradigm is proposed to improve the nanoscale double gate junctionless DGJL MOSFET electrical performance. A careful mechanism study based on numerical investigation and a performance comparison between the proposed and conventional design is carried out. The device figures-of-merit, governing the switching and leakage current behavior are investigated in order to reveal the transistor electrical performance for ultra-low power consumption. It is found that the channel doping engineering feature has a profound implication in enhancing the device electrical performance. Moreover, the impact of the high-k gate dielectric on the device leakage performance is also analyzed. The results show that the proposed design with gate stacking demonstrates superior \(I_{{\textit{ON}}}/I_{{\textit{OFF}}}\) ratio and lower leakage current as compared to the conventional counterpart. Our analysis highlights the good ability of the proposed design including a high-k gate dielectric for the reduction of the leakage current. These characteristics underline the distinctive electrical behavior of the proposed design and also suggest the possibility for bridging the gap between the high derived current capability and low leakage power. This makes the proposed GCD-DGJL MOSFET with gate stacking a potential alternative for high performance and ultra-low power consumption applications.     

Fabrication of a superconducting flux flow transistor with a serial-channel structure by an AFM lithography method

Atomic force microscopy (AFM) has become an attractive technique to fabricate nano devices since the observing mechanism is different from fabricating one. We have fabricated the superconducting flux flow transistor (SFFT) with a serial-channel structure using the AFM lithography analyzed the modified surface by the AFM image. We investigated the induced voltage in a serial-channel terminals dependence on the gate current by the I–V measurement system. We performed the numerical simulation to get the theoretical characteristics of the SFFT controlled by the gate current via the modified channel. The transresistance was 0.006 Ω for I_d=51 mA at I_g=5 mA. It is very low transresistance in comparison with SFFTs fabricated by the other processes, however our results show that the SFFT with a serial-channel structure is effectively fabricated by an AFM lithography method.     

High-blocking-voltage UMOSFETs with reformed electric field distribution

A high-performance vertical GaN metal–oxide–semiconductor field-effect transistor (MOSFET) with a U-shaped gate (UMOSFET) and high blocking voltage is proposed. The main concept behind this work is to reform the electric field distribution to achieve high blocking voltage. The proposed structure includes p-regions in the drift region, which we call reformed electric field (REF) regions. Simulations using the two-dimensional SILVACO simulator reveal the optimum doping concentration, and width and height of the REF regions to achieve the maximum depletion region at the breakdown voltage in the drift region. Also, the electric field distribution in the REF-UMOSFET is reformed by producing additional peaks, which decreases the common peaks under the gate trench. We discuss herein the impact of the height, width, and doping concentration of the REF regions on the ON-resistance (R_ON) and blocking voltage. The blocking voltage, specific ON-resistance, and figure of merit \( \left( {{\text{FOM}} = \frac{{V_{{{\text{BR}}}}^{2} }}{{R_{{{\text{ON}}}} }}} \right) \) are 1140 V, 0.587 mΩ cm² (V_GS = 15 V, V_DS = 1 V), and 2.214 GW/cm², respectively. The blocking voltage and FOM are increased by about 72 % and 171 % in comparison with a conventional UMOSFET (C-UMOSFET).     

Scalability and process induced variation analysis of polarity controlled silicon nanowire transistor

In this paper, we present scalability and process induced variation analysis of polarity gate silicon nanowire field-effect transistor. 3D simulation results show that the PGFET offers significant reduction in short channel effects and variability due to utilization of uniform lightly doped silicon nanowire (SiNW) as compare to highly doped silicon nanowire in junctionless transistors. The performance parameters were evaluated for different device geometries, such as variation in SiNW radius, equivalent oxide thickness, channel length and spacer length. Sensitivity analysis shows that the PGFET exhibits less dependence towards gate length in comparison to other device parameters. It is seen that ON to OFF current ratio variation with silicon nanowire thickness is lower for PGFET as compared to JLFET. The threshold voltage roll-off and sensitivity towards intrinsic delay in PGFET is much lower than its counterpart device.     

Dielectric pocket double gate junctionless FET: a new MOS structure with improved subthreshold characteristics for low power VLSI applications

In this paper, we report the TCAD based simulation of a new double-gate junctionless FETs (DG-JLFETs) structure incorporating dielectric pockets (DPs) at the source and drain ends. The proposed structure not only improves the ON to OFF drain current ratio (by \({\sim }\)900 %), subthreshold swing characteristics (by \({\sim }\)12 %) and Drain Induced Barrier Lowering (DIBL) (by \({\sim }\)56 %) over the conventional DG-JLFETs (i.e. without DPs), but also provides additional flexibility of performance optimization of the device by changing the length and thickness of the DPs. Since only little work has been carried out on the performance optimization of the JLFETs, the present work is believed to be very useful for designing the low-power VLSI circuits using DP-DG JLFETs with improved performance.     

ESD robustness improvement for integrated DMOS transistors —the different gate‐voltage dependence of It2 between VDMOS and LDMOS transistors

This paper presents the device‐level electrostatic discharge (ESD) robustness improvement for integrated vertical double‐diffused MOS (VDMOS) and lateral double‐diffused MOS (LDMOS) transistors by changing device structure. The ESD robustness of VDMOS transistor was improved by preventing current concentration and that of LDMOS transistor was improved by relaxing the electric field under the LOCOS oxide. We found the different gate‐voltage dependence of the second breakdown current (I_t2) between VDMOS and LDMOS transistors. © 2011 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.