Corrosion inhibition of C38 steel in 1 M hydrochloric acid medium by alkaloids extract from Oxandra asbeckii plant

The inhibition effect of alkaloids extract from Oxandra asbeckii plant (OAPE) on the corrosion of C38 steel in 1 M hydrochloric acid solution has been investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The corrosion inhibition efficiency increases on increasing plant extracts concentration. Cathodic and anodic polarization curves show that OAPE is a mixed-type inhibitor. The effect of temperature on the corrosion behavior of C38 steel in 1 M HCl with and without addition of plant extract was studied in the temperature range 25–55 °C. The thermodynamic functions of dissolution and adsorption processes were calculated from experimental polarization data and the interpretation of the results are given. The adsorption of this plant extract on the C38 steel surface obeys the Langmuir adsorption isotherm. Surface analysis (Raman) was also carried out to establish the corrosion inhibitive property of this plant extract in HCl solution.     

Electrochemical frequency modulation and inductively coupled plasma atomic emission spectroscopy methods for monitoring corrosion rates and inhibition of low alloy steel corrosion in HCl solutions and a test for validity of the Tafel extrapolation method

The inhibition effect of glycine (Gly) towards the corrosion of low alloy steel ASTM A213 grade T22 boiler steel was studied in aerated stagnant 0.50 M HCl solutions in the temperature range 20-60 °C using potentiodynamic polarization (Tafel polarization and linear polarization) and impedance techniques, complemented with scanning electron microscope (SEM) and energy dispersive X-ray (EDX). Electrochemical frequency modulation (EFM), a non-destructive corrosion measurement technique that can directly give values of corrosion current without prior knowledge of Tafel constants, is also presented here. Experimental corrosion rates determined by the Tafel extrapolation method are compared with corrosion rates obtained by electrochemical, namely EFM technique, and chemical (i.e., non-electrochemical) method for steel in HCl. The chemical method of confirmation of the corrosion rates involved determination of the dissolved cation, using ICP-AES (inductively coupled plasma atomic emission spectrometry) method of analysis. Corrosion rates (in mm y⁻¹) obtained from the electrochemical (Tafel extrapolation and EFM) and the chemical method, ICP, are in a good agreement. Polarization studies have shown that Gly is a good “green”, mixed-type inhibitor with cathodic predominance. The inhibition process was attributed to the formation of an adsorbed film on the metal surface that protects the metal against corrosive agents. Scanning electron microscopy (SEM) and energy dispersion X-ray (EDX) examinations of the electrode surface confirmed the existence of such an adsorbed film. The inhibition efficiency increases with increase in Gly concentration, while it decreases with solution temperature. Temkin isotherm is successfully applied to describe the adsorption process. Thermodynamic functions for the adsorption process were determined.     

Corrosion inhibition of austenitic stainless steel by some pyrimidine compounds in hydrochloric acid

The inhibition effect of two pyrimidine derivatives on the corrosion of austenitic stainless steel in 1 M HCl has been studied by Tafel plot, linear polarization, and electrochemical impedance spectroscopy (EIS) at 298 K. Results showed that compounds inhibited steel corrosion in a 1 M HCl solution and inhibition efficiencies increased with the concentration of inhibitor. Polarization curves indicated that all studied pyrimidine derivatives act as mixed type (cathodic/anodic) inhibitors. The adsorption of the inhibitors on the stainless steel surface was found to obey the Langmuir and Dubinin–Radushkevich adsorption isotherm models. Negative values of ΔG_ads in the acidic media ensured the spontaneity of the adsorption process.     

Synthesis and evaluation of Tris-hydroxymethyl-(2-hydroxybenzylidenamino)-methane as a corrosion inhibitor for cold rolled steel in hydrochloric acid

Tris-hydroxymethyl-(2-hydroxybenzylidenamino)-methane (THHM) was synthesized. The effect of THHM on the corrosion of cold rolled steel (CRS) in 0.1 M hydrochloric acid was then investigated by Tafel polarization curve and electrochemical impedance spectroscopy (EIS). Polarization curve results clearly reveal the fact that THHM is a good cathodic type inhibitor. EIS results confirm its corrosion inhibition ability. The inhibition efficiency increases with increasing THHM concentration but decreases with immersion time. Atomic force microscopy (AFM) reveals that a protective film forms on the surface of the inhibited sample. The adsorption of this inhibitor is found to follow the Langmuir adsorption isotherm. THHM adsorbs on the sample probably by chemisorption.     

Adsorbtion and inhibition effect of thiourea on mild steel in acidic media

The effect of thiourea on electrochemical corrosion behavior of mild steel was investigated in 0.5M HCl solution at room temperature by electrochemical impedance spectroscopy (AC Impedance) and Tafel polarization (DC Polarization) methods. The results show that thiourea act as mixed type inhibitor. The inhibition efficiency obtained from AC Impedance and DC polarization methods are in good agreement. The Nyquist plots show that the corrosion behavior of mild steel in 0.5M HCl solution in the absence and in the presence of thiourea, consist a simple capacitive loop. Changes in impedance parameters (R_ct and C_dl) are indicative of adsorption of thiourea on the metal surface, leading to the formation of protective film. Thiourea is found to adsorb on mild steel surface steel in 0.5M HCl solution, according to the Langmuir adsorption isotherm.     

Corrosion inhibition of mild steel in hydrochloric acid solution by Schiff base furoin thiosemicarbazone

A heterocyclic Schiff base furoin thiosemicarbazone was tested for its corrosion inhibition towards mild steel in 1 M HCl solution using weight loss, Tafel polarization and electrochemical impedance spectroscopy techniques. Furoin thiosemicarbazone revealed good corrosion inhibition efficiency even at low concentrations towards mild steel in HCl medium. Comparison of corrosion inhibition efficiency of Schiff base and its parent amine and effect of temperature on inhibition efficiency were also investigated. The adsorption of furoin thiosemicarbazone on mild steel surface obeys Langmuir isotherm.     

Corrosion Protection Properties of 4-[(E)-[(2,4-Dihydroxy phenyl)methylidene] amino]-6-methyl-3-sulfanylidene-2,3,4,5-tetrahydro-1,2,4-triazin-5-one [DMSTT] Toward Mild Steel in Sulfuric Acid

The inhibition of mild steel corrosion in aerated 0.5 N H₂SO₄ solution was investigated using potentiodynamic polarization studies (Tafel), linear polarization studies, electrochemical impedance spectroscopy studies, adsorption studies, and surface morphological studies. The effect of inhibitor concentration on corrosion rate, the effect of temperature, degree of surface coverage, adsorption kinetics, and surface morphology are investigated. The inhibition efficiency increased markedly with increase in the additive concentration and decreased slightly with increasing temperature. The presence of DMSTT decrease the double-layer capacitance and increase the charge transfer resistance. The value of activation energy (E _a) of metal corrosion, adsorption equilibrium constant (K _ads), and free energy of adsorption (ΔG _ads) were calculated from the temperature dependence of corrosion current. The adsorption of inhibitor molecule on mild steel surface follow Langmuir isotherm. DMSTT offers excellent inhibition properties and acts as a mixed-type inhibitor.     

Inhibition of aluminum corrosion using Opuntia extract

The inhibitive action of the mucilage extracted from the modified stems of prickly pears, toward acid corrosion of aluminum, is tested using weight loss, thermometry, hydrogen evolution and polarization techniques. It was found that the extract acts as a good corrosion inhibitor for aluminum corrosion in 2.0 M HCl solution. The inhibition action of the extract was discussed in view of Langmuir adsorption isotherm. It was found that the adsorption of the extract on aluminum surface is a spontaneous process. The inhibition efficiency (IE) increases as the extract concentration is increased. The effect of temperature on the IE was studied. It was found that the presence of extract increases the activation energy of the corrosion reaction. Moreover, the thermodynamic parameters of the adsorption process were calculated. It was found also that the Opuntia extract provides a good protection to aluminum against pitting corrosion in chloride ion containing solutions.     

Corrosion inhibition of carbon steel in hydrochloric acid solution by fruit peel aqueous extracts

The inhibitive action of the aqueous extracts of fruit peels against corrosion of carbon steel in a 1 M HCl solution was investigated using electrochemical impedance spectroscopy, potentiodynamic polarization curves, weight loss measurements and surface analysis. We analyzed aqueous extracts of mango, orange, passion fruit and cashew peels in different concentrations and found that the extracts act as good corrosion inhibitors for the tested system. The inhibition efficiency increases with increasing extract concentration and decreases with temperature. The adsorption of components of the fruit peel extracts on the surface of the carbon steel follows the Langmuir adsorption isotherm.     

Synergistic inhibition between dodecylamine and potassium iodide on the corrosion of cold rolled steel in 0.1 M phosphoric acid

The corrosion inhibition of cold rolled steel in 0.1 M aerated phosphoric acid (H₃PO₄) in the presence of dodecylamine (DDA) and potassium iodide (KI) has been investigated by Tafel polarization curve and electrochemical impedence spectroscopy (EIS) at 20 °C. The results obtained from polarization curve show that the inhibition efficiency of DDA with and without KI increases with increase in concentration of DDA but the inhibition efficiency of DDA without KI is not too high. A synergistic effect exists when DDA and KI are combined together to prevent cold rolled steel corrosion in 0.1 M H₃PO₄. All impedance spectra in EIS tests exhibit one capacitive loop which indicates that the corrosion reaction is controlled by charge transfer process. Inhibition efficiencies obtained from Tafel polarization, transfer resistance (R_t) are consistent.     

Rhodanine azosulpha drugs as corrosion inhibitors for corrosion of 304 stainless steel in hydrochloric acid solution

The effect of rhodanine azosulpha drugs on the corrosion behaviour of 304 stainless steel in 1.0 M hydrochloric acid solution as corrosive medium has been investigated using weight loss and potentiostatic polarization techniques. Some corrosion parameters such as anodic and cathodic Tafel slope, corrosion potential, corrosion current, exchange current densities, surface coverage and inhibition efficiency were calculated. The polarization measurements indicated that the inhibitors are of mixed type and inhibit corrosion by parallel adsorption on the surface of steel due to the presence of more than one active centre in the inhibitor molecule. The adsorption is obeyed Langmuir adsorption isotherm. The activation energy and thermodynamic parameters were calculated at different temperature.     

Corrosion inhibition of mild steel by plant extract in dilute HCl medium

The inhibition effect of Zenthoxylum alatum plant extract on the corrosion of mild steel in 5% and 15% aqueous hydrochloric acid solution has been investigated by weight loss and electrochemical impedance spectroscopy (EIS). The corrosion inhibition efficiency increases on increasing plant extract concentration till 2400 ppm. The effect of temperature on the corrosion behaviour of mild steel in 5% and 15% HCl with addition of plant extract was studied in the temperature range 50-80 °C. Surface analysis (SEM, XPS and FT-IR) was also carried out to establish the corrosion inhibitive property of this plant extract in HCl solution. Plant extract is able to reduce the corrosion of steel more effectively in 5% HCl than in 15% HCl. The adsorption of this plant extract on the mild steel surface obeys the Langmuir adsorption isotherm.     

Effectiveness of Croton cajucara Benth on corrosion inhibition of carbon steel in saline medium

Application of corrosion inhibitors is one of the most common practices for the protection of steel structures and their alloys in industry. Since metallic corrosion is a major cause of economic losses in the oil industry, the use of natural inhibitors is an alternative for sustainable technological development. In the present study the effectiveness of the hydroalcoholic extract of the plant species Croton cajucara Benth (CC) dissolved in a microemulsion system (MES‐CC) as well as in dimethyl sulfoxide (DMSO‐CC) was evaluated as corrosion inhibitor on carbon steel AISI 1020 in saline medium. Surface tension measurements of the MES‐CC confirmed micelle formation, and rheological data showed that viscosity varies with temperature. According to potentiodynamic technique and Tafel extrapolation, maximum inhibition efficiencies were effective (93.84% for MES‐CC and 64.73% for DMSO‐CC) with predominant control of cathodic reaction. The adsorption of MES‐CC on carbon steel surface obeys Langmuir adsorption isotherm, while DMSO‐CC was found to follow the Frumkin isotherm.     

柚子皮提取物对C38的缓蚀作用

目的研究柚子皮提取物对C38钢在1 mol/L HCl中的缓蚀作用。方法通过索氏提取器从柚子皮中提取天然绿色缓蚀剂,进而与0.01 mol/L KI进行复配,采用失重法和电化学测试法分析柚子皮提取物的缓蚀作用机理。结果失重实验表明,柚子皮提取物对C38钢的缓蚀作用最高达93%,而与0.01mol/L KI复配使用后缓蚀效率最高达98%以上。同时表明其在碳钢表面的吸附符合Langmuir吸附等温式;Tafel极化曲线表明其能同时抑制碳钢腐蚀的阴、阳极过程;碳钢的阻抗值随着柚子皮提取物浓度的增加而增大。结论柚子皮提取物是很好的缓蚀剂,与卤素离子复配后效果更佳。     

Evaluation of Eulychnia acida and Echinopsis chiloensis (Cactaceae) extracts in inhibiting corrosion of carbon steel in HCl solution

In the present study, the activity of extracts obtained from the stems of two endemic species of the central–northern region of Chile (Eulychnia acida [Copao] and Echinopsis chiloensis [Quisco]), was evaluated as potential corrosion inhibitors for carbon steel in 0.1 M HCl. The total content of phenols and flavonoids in the extracts was determined, and the main components were identified by high-performance liquid chromatography–mass spectrometry, being similar in both species. The inhibition efficiency of extracts was evaluated by mass loss measures, Tafel polarization curves, and electrochemical impedance spectroscopy. The assay results showed similar values in inhibition percentages, around 88% at extract concentrations of 1,500 ppm. The adsorption on the steel surface followed the Langmuir model adsorption isotherm, whose thermodynamic parameters (ΔG°_ads for Copao and Quisco, −17.81 and −17.70 kJ/mol, respectively) suggest a physisorption mechanism. The scanning electron microscopy analyses showed that in the presence of the extracts, the surface of the steel is covered by a thin film that allows the sanding marks to be visualized; while without the extracts the surface is rough due to the HCl corrosion effect.     

Electrochemical studies on the effect of pyrazolo‐containing compounds on the corrosion of carbon steel in 1 M sulphuric acid

The effect of some synthesized pyrazolo containing compounds on the corrosion of carbon steel in 1 M H₂SO₄ was investigated. The investigation involved electrochemical polarization methods (potentiodynamic, Tafel extrapolation and the determination of the polarization resistance). A significant decrease in the corrosion rate of carbon steel was observed in the presence of the investigated compounds. The results show that these compounds act as mixed type inhibitors, but the cathode is more preferentially polarized. The relative inhibition efficiency of these compounds depends on both the nature and concentrations of the investigated compounds. Compounds are found to adsorb on the carbon steel surface according to the Langmuir adsorption isotherm.     

The role of acid anion on the inhibition of the acidic corrosion of steel by lupine extract

The inhibitive effect of lupine (Lupinous albus L.) extract on the corrosion of steel in aqueous solution of 1 M sulphuric and 2 M hydrochloric acids was investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. Potentiodynamic polarization curves indicated that the lupine extract acts as a mixed-type inhibitor. EIS measurements showed that the dissolution process is under activation control. The inhibition efficiency of the extract obtained from impedance and polarization measurements was in a good agreement and was found to increase with increasing concentration of the extract. The obtained results showed that, the lupine extract could serve as an effective inhibitor for the corrosion of steel in acid media and the extract was more effective in case of hydrochloric acid. Theoretical fitting of the corrosion data to the kinetic-thermodynamic model was tested to show the nature of adsorption.     

Curcumin Derivatives as Green Corrosion Inhibitors for α-Brass in Nitric Acid Solution

1,7-Bis-(4-hydroxy-3-methoxy-phenyl)-hepta-1,6-diene-4-arylazo-3,5-dione I-V have been investigated as corrosion inhibitors for ??-brass in 2?M nitric acid solution using weight-loss and galvanostatic polarization techniques. The efficiency of the inhibitors increases with the increase in the inhibitor concentration but decreases with a rise in temperature. The conjoint effect of the curcumin derivatives and KSCN has also been studied. The apparent activation energy (E _a*) and other thermodynamic parameters for the corrosion process have also been calculated. The galvanostatic polarization data indicated that the inhibitors were of mixed-type, but the cathode is more polarized than the anode. The slopes of the cathodic and anodic Tafel lines (b _c and b _a) are maintained approximately equal for various inhibitor concentrations. However, the value of the Tafel slopes increases together as inhibitor concentration increases. The adsorption of these compounds on ??-brass surface has been found to obey the Frumkin??s adsorption isotherm. The mechanism of inhibition was discussed in the light of the chemical structure of the undertaken inhibitors.     

Inhibition effect of a new pyrimidine derivative on the corrosion of mild steel in hydrochloric acid solution

The inhibition effect of a newly synthesized pyrimidine derivative, namely 3-(2-(4-(hydroxymethyl)-1H-1,2,3-triazol-1-yl)ethyl)-2-methyl-6,7,8,9-tetrahydropyrido[1,2-a]pyrimidin-4-one, on the corrosion of mild steel in 1.0 M HCl medium was investigated using the weight loss, the Tafel extrapolation technique and the AC impedance spectroscopy. The effect of the inhibitor concentration, temperature and concentration of the acid mixture media on the inhibitor action was also studied. It was observed that the anti-corrosion efficiency increases with an increase in the inhibitor concentration, but decreases with an increase in temperature. Thermodynamic parameters for the dissolution process were determined. The adsorption of the pyrimidine derivative on the mild steel surface was found to obey the Langmuir adsorption isotherm.     

The inhibition effect of the new Schiff base,namely 2,2′‐[bis‐N(4‐choloro benzaldimin)]‐1,1′‐dithio against mild steel corrosion

2,2′‐[bis‐N(4‐choloro benzaldimin)]‐1,1′‐dithio has been synthesized and its inhibiting action on the corrosion of mild steel in 0.5 M sulfuric acid was investigated by various corrosion monitoring techniques, such as weight loss and potentiodynamic polarization techniques. The experimental results suggest that this compound is a good corrosion inhibitor for mild steel and the inhibition efficiency increases with the increase in inhibitor concentration. This organic compound is a mixed type inhibitor in the acid solution, and its adsorption on the mild steel surface is also found to obey the Langmuir adsorption isotherm.