The effect of mixed nanoadditive‐blended diesel–water emulsion on the performance,combustion, and emission characteristics of a DI diesel engine

The present paper examines the impact of mixed nanoadditive (Al₂O₃ and ZnO) incorporated diesel–water emulsion on the combustion, performance, and emission of a single‐cylinder diesel engine under varying load conditions. The test fuels consist of constant fuel ratio of 88% diesel, 10% water, and 2% surfactant. Also, different concentrations of mixed nanoadditives—50 ppm, 100 ppm, and 150 ppm—are added to the test fuel. The ultrasonicator bath is employed for agitation or stirring of test fuels. The test results indicate that the mixed nanoadditives in diesel–water emulsion improve combustion characteristics, brake thermal efficiency, and brake‐specific fuel consumption, whereas the maximum improvement is achieved at full load. It is also determined from the test results that the nanoadditive‐blended test fuel showed a noticeable decrement in CO, NO_x, and hydrocarbon emissions as compared with neat diesel. The optimum results are obtained for D88S2W10ZA150 blend. Owing to the higher surface‐to‐volume ratio, enhanced atomization rate, high catalytic behavior, and shortened ignition delay are possible reasons to improve diesel engine working characteristics.     

Performance and emission characteristics of turpentine–diesel dual fuel engine and knock suppression using water diluents

In the present work, a normal diesel engine was modified to work in a dual fuel (DF) mode with turpentine and diesel as primary and pilot fuels, respectively. The resulting homogeneous mixture was compressed to a temperature below the self‐ignition point. The pilot fuel was injected through the standard injection system and initiated the combustion in the primary‐fuel air mixture. The primary fuel (turpentine) has supplied most of the heat energy. Usually, in all DF engines, low‐cetane fuels are preferred as a primary fuel. Therefore, at higher loads these fuels start knocking and deteriorating in performances. Usually, DF operators suppress the knock by adding more pilot‐fuel quantity. But in the present work, a minimum pilot‐fuel quantity was maintained constant throughout the test and a required quantity of diluent (water) was added into the combustion at the time of knocking. The advantages of this method of knock suppression are restoration of performance at full load, maintenance of the same pilot quantity through the load range and reduction in the fuel consumption at full load. From the results, it was found that all performance and emission parameters of turpentine, except volumetric efficiency, are better than those of diesel fuel. The emissions like CO, UBHC are higher than those of the diesel baseline (DBL) and around 40–45% reduction of smoke was observed at 100% of full load. The major pollutant of diesel engine, NO_x, was found to be equal to that of DBL. From the above experiment, it was proved that approximately 80% replacement of diesel with turpentine is quite possible. Copyright © 2006 John Wiley & Sons, Ltd.     

Review of NOx reduction technologies in CI engines fuelled with oxygenated biomass fuels

Oxygenated fuels like biodiesel and alcohols have the potential to provide a reliable and a cost effective alternative to India's increasing future energy demands. They have a prospective future since they are renewable and can be produced easily in India's rural areas. Due to rapid industrialization and the increased number of vehicles on the road, the energy needs of the country are increasing rapidly. Oxygenated fuels can substantially replace the large demand for diesel to generate power for the industries and to fuel diesel engines of the vehicles. In spite of the many advantages of using them, most of the researchers have reported higher NO_x emissions, which is a deterrent to the market expansion of these fuels. The present program aims to review the NO_x emissions from the CI engines fuelled with oxygenated fuels. To meet the stringent emission norms, the various NO_x reduction technologies like use of additives, retarded fuel injection timing, biodiesel emulsion with water, and exhaust gas recirculation are reviewed. The results of the most effective and low cost technique of EGR in DI diesel engine fuelled with biodiesel–diesel blends and tri-compound oxygenated diesel fuel blends (ethanol–biodiesel–diesel fuel blends and methanol–biodiesel–diesel fuel blends) are presented.     

Experimental investigation on diesel engine with diestrol-water micro emulsions

Experiments were conducted on a single cylinder direct injection diesel engine using diesel, biodiesel and biodiesel-diesel-ethanol (diestrol) water micro emulsion fuels to investigate the performance, emission and combustion characteristics of the engine under different load conditions at a constant speed of 1500 rpm. The results indicated that biodiesel and micro emulsion fuels had a higher brake specific fuel consumption (BSFC) than that of diesel. A slight improvement in the brake specific energy consumption (BSEC) was observed for micro emulsion fuels. The brake thermal efficiency of biodiesel and micro emulsion fuels were comparable to that of diesel. The emission characteristics like carbon monoxide (CO), carbon dioxide (CO₂), unburnt hydrocarbon (UHC), nitric oxide (NO) and smoke emissions for biodiesel and micro emulsion fuels were lower than diesel fuel at all load conditions. The cylinder gas pressure of micro emulsion fuels was lower than diesel at low loads but it became almost identical to diesel at medium and full load conditions. The heat release rate for micro emulsion fuels was higher than biodiesel and diesel fuels for all loads. Biodiesel showed shorter ignition delay for the entire load range and the longer ignition delay observed for micro emulsion fuels.     

Hydrogen addition to tea seed oil biodiesel: Performance and emission characteristics

Compression ignition engines are the dominant tools of the modern human life especially in the field of transportation. But, the increasing problematic issues such as decreasing reserves and environmental effects of diesel fuels which is the energy source of compression ignition engines forcing researchers to investigate alternative fuels for substitution or decreasing the dependency on fossil fuels. The mostly known alternative fuel is biodiesel fuel and many researchers are investigating the possible raw materials for biodiesel production. Also, hydrogen fuel is an alternative fuel which can be used in compression ignition engines for decreasing fuel consumption and hazardous exhaust emissions by enriching the fuel. In this study, influences of hydrogen enrichment to diesel and diesel tea seed oil biodiesel blends (B10 and B20) were investigated on an unmodified compression ignition engine experimentally. In consequence of the experiments, lower torque and higher brake specific fuel consumption data were measured when the engine was fuelled diesel biodiesel blends (B10 and B20) instead of diesel fuel. Also, diesel biodiesel blends increased CO₂ and NO_x emissions while decreasing the CO emissions. Hydrogen enrichment (5 l/m and 10 l/m) was improved the both torque and brake specific fuel consumption for all test fuels. Furthermore, hydrogen enrichment reduced CO and CO₂ emissions due to absence of carbon atoms in the chemical structure for all test fuels. Increasing flow rate of hydrogen fuel from 5 l/m to 10 l/m further improved performance measures and emitted harmful gases except NO_x. The most significant drawback of the hydrogen enrichment was the increased NO_x emissions.     

Characterization of kilowatt-scale autothermal reformer for production of hydrogen from heavy hydrocarbons

Catalytic autothermal reforming is considered one of the most effective methods of producing hydrogen from heavy hydrocarbon fuels, such as diesel fuel, for fuel cell or emissions reduction applications. This article describes an investigation of the reactor characteristics and catalytic efficiency of a kilowatt-scale catalytic autothermal reformer currently being developed at Argonne National Laboratory. Dodecane and hexadecane were used individually as surrogates for diesel fuels to simply the reaction study and the interpretation of the test results. The reforming of these hydrocarbon fuels was examined at a variety of oxygen-to-carbon and steam-to-carbon ratios at gas hourly space velocities ranging from 10,000 to 100,000 h⁻¹. At steady state, the product composition correlated well with that calculated from thermodynamic equilibrium at a representative equivalent temperature. The oxygen-to-carbon ratio was determined to be the most significant operating parameter that influenced the reforming efficiency; the reforming efficiency (and the selectivity to CO_x) increased with increasing oxygen-to-carbon ratio up to about 0.42, at which value the maximum efficiency was attained.     

Environmental effects of adding aluminum oxide nano-additives on diesel engine fueled with pyrolyzed biomass oil–​diesel blends

The present study focuses on the investigation of environmental effects of adding aluminum oxide (Al₂O₃) nanoparticles as nano-additive in diesel-pyrolyzed biomass oil (PBO) blends. The PBO was extracted from jatropha seeds through the catalytic pyrolysis process at a temperature ranging from 450°C to 550°C. The esterification of PBO has been carried out using a catalyst in the presence of methyl alcohol to improve its physical properties and quality. The Al₂O₃ nano-additives were dispersed into PBO20 (20% of PBO and 80% of diesel) and PBO40 (40% of PBO and 60% of diesel) blends with a concentration of 50 ppm. The physical properties of test fuel blends were measured and compared with diesel. The engine emission tests were carried out using these blends at a constant speed of 1500 rpm by varying the load. The emission constituents such as CO, HC, and smoke were reduced. However, the emissions like CO₂ and NO were increased by the addition of nano-additives compared to diesel.     

Liquid hydrocarbon fuels from fish oil industrial residues by catalytic cracking

In the present work, catalytic cracking of fish oil industrial residue was investigated to study the effect of temperature, type of catalyst and the heating rate on the yield of organic liquid fraction (OLF) and its acid value. The highest bio‐oil yield of 72% (wt.) was obtained at temperature range of 300–500 °C and heating rate of 10 °C/min with the mixture of Al₂O₃ and Na₂CO₃ as a catalyst. It was found that the mixture of Na₂CO₃ and MgSO₄ as a catalyst gives lowest acid value of 8.75 mg_KOH/g_oil and 68.1% of OLF yield. Furthermore, the acid value is reduced to 0.36 mg_KOH/g_oil using Na₂CO₃ as an absorbent. The results show that the catalytic cracking process represents a sustainable method to produce bio‐oil from fish oil industrial residues with physicochemical characteristics similar to the diesel fuel. Copyright © 2012 John Wiley & Sons, Ltd.     

Combined impact of varying biogas mass flow rate and rice bran methyl esters blended with diesel on a dual-fuel engine

ABSTRACT

For fetching day-to-day energy needs, current energy requirement majorly depends on fossil fuels. But ambiguous matter like abating petroleum products and expanding air pollution has enforced the experts to strive for another fuel which can be used as an alternative or reduce the applications of fossil fuels. Considering the issues, the main objective of the present study is to find the feasibility by using blends of rice bran oil biodiesel and diesel which are used as pilot fuels by blending 10% and 20% biodiesel in fossil diesel and biogas, introduced as gaseous fuel by varying its mass flow rate in a dual-fuel engine mode. An experimentation study was carried out to find the performance and emission parameters of the engine relative to pure diesel. The results were very much similar to the majority of researchers who used biodiesel and gaseous fuels in a dual-fuel engine. Brake specific fuel consumption (BSFC) of the engine was noticed to have increased, while brake thermal efficiency was on the lower side in dual fuel mode in comparison with regular diesel. In relation with conventional diesel, it was noticed that combined effect of rice bran methyl esters and varying mass flow rate of biogas showed a decrement in NO _x and smoke emissions, whereas HC and CO exhalations were on higher side when biogas and biodiesel were utilized collectively in dual-fuel engine. Hence, it was concluded that combination of blends of biodiesel and diesel and introduction of biogas in the engine can be a promising combination which can be used as a substitute fuel for addressing future energy needs.     

Vegetable oils as renewable fuels for power plants based on low and medium speed diesel engines

There is a high potential for plant oils as alternative fuel for low and medium speed diesel engines, making petroleum-derived fuels likely to be replaced in these types of engines. Vegetable oils have important advantages over both heavy fuel oil (HFO) and marine gas oil (MGO), the fuels currently used in diesel power plants by large two stroke low-speed diesel engines and by medium speed diesel engines, respectively. The emission of certain pollutants and greenhouse gases like SO_x, soot and, mainly, CO₂ can be reduced by using vegetable oils in these types of engines. This work discusses the potential of vegetable oils as fuel for power plant diesel engines and the problems that can be derived from their use. Current experiences with medium speed diesel engines together with the analysis carried out in this paper indicate that vegetable oils can substitute HFO and MGO, without almost any engine modification.     

Influence of advanced injection timing on the performance and emissions of CI engine fueled with ethanol‐blended diesel fuel

Ethanol has been considered as an alternative fuel for diesel engines. On the other hand, injection timing is a major parameter that sensitively affects the engine performance and emissions. Therefore, in this study, the influence of advanced injection timing on the engine performance and exhaust emissions of a single cylinder, naturally aspirated, four stroke, direct injection diesel engine has been experimentally investigated when using ethanol‐blended diesel fuel from 0 to 15% with an increment of 5%. The original injection timing of the engine is 27° crank angle (CA) before top dead center (BTDC). The tests were conducted at three different injection timings (27, 30 and 33° CA BTDC) for 30 Nm constant load at 1800 rpm. The experimental results showed that brake‐specific energy consumption (BSEC), brake‐specific fuel consumption (BSFC), NO_x and CO₂ emissions increased as brake‐thermal efficiency (BTE), smoke, CO and HC emissions decreased with increasing amount of ethanol in the fuel mixture. Comparing the results with those of original injection timing, NO_x emissions increased and smoke, HC and CO emissions decreased for all test fuels at the advanced injection timings. For BSEC, BSFC and BTE, advanced injection timings gave negative results for all test conditions. Copyright © 2008 John Wiley & Sons, Ltd.     

Effect of ethanol–diesel blend fuels on emission and particle size distribution in a common-rail direct injection diesel engine with warm-up catalytic converter

In this study, the exhaust gas from a common-rail direct injection diesel engine was investigated both upstream and downstream warm-up catalytic converters (WCC). Three different types of ultra-low sulfur fuels (ethanol–diesel blend, ethanol–diesel blend with cetane improver and pure diesel) were tested in this study. The objective of the work was to study the engine performance and the formation of THC (total hydro carbon), CO (carbon monoxide), NO_x (nitrogen oxides), smoke and PM (particulate matters) when using these fuels. THC and CO emissions of the ethanol–diesel blend fuels were slightly increased, and about 50–80% mean conversion efficiencies of THC and CO on catalysts were achieved in the ECE R49 13-mode cycle. Smoke was decreased by more than 42% in the entire ECE 13-mode cycles. From the measurement of scanning mobility particle sizer (SMPS) for the particle size range of 10–385 nm, the total number and total mass of the PM of the ethanol–diesel blend fuels were decreased by about 11.7–15% and 19.2–26.9%, respectively.     

An insight on hydrogen fuel injection techniques with SCR system for NOX reduction in a hydrogen–diesel dual fuel engine

Internal combustion engines continue to dominate in many fields like transportation, agriculture and power generation. Among the various alternative fuels, hydrogen is a long-term renewable and less polluting fuel (Produced from renewable energy sources). In the present experimental investigation, the performance and emission characteristics were studied on a direct injection diesel engine in dual fuel mode with hydrogen inducted along with air adopting carburetion, timed port and manifold injection techniques. Results showed that in timed port injection, the specific energy consumption reduces by 15% and smoke level by 18%. The brake thermal efficiency and NO_X increases by 17% and 34% respectively compared to baseline diesel. The variation in performance between port and manifold injection is not significant. The unburnt hydrocarbons and carbon monoxide emissions are lesser in port injection. The oxides of nitrogen are higher in hydrogen operation (both port and manifold injection) compared to diesel engine. In order to reduce the NO_X emissions, a selective catalytic converter was used in hydrogen port fuel injection. The NO_X emission reduced upto a maximum of 74% for ANR (ratio of flow rate of ammonia to the flow rate of NO) of 1.1 with a marginal reduction in efficiency. Selective catalytic reduction technique has been found to be effective in reducing the NO_X emission from hydrogen fueled diesel engines.     

An experimental investigation on manifold‐injected hydrogen as a dual fuel for diesel engine system with different injection duration

Stringent emission norms and rapid depletion of petroleum resources have resulted in a continuous effort to search for alternative fuels. Hydrogen is one of the best alternatives for conventional fuels. Hydrogen has both the benefits and limitation to be used as a fuel in an automotive engine system. In the present investigation, hydrogen was injected into the intake manifold by using a hydrogen gas injector and diesel was introduced in the conventional, mode which also acts as an ignition source for hydrogen combustion. The flow rate of hydrogen was set at 5.5 l min^?1 at all the load conditions. The injection timing was kept constant at top dead center (TDC) and injection duration was adjusted to find the optimized injection condition. Experiments were conducted on a single cylinder, four stroke, water‐cooled, direct injection diesel engine coupled to an electrical generator. At 75% load the maximum brake thermal efficiency for hydrogen operation at injection timing of TDC and with injection duration of 30°CA is 25.66% compared with 21.59% for diesel. The oxides of nitrogen (NO_X) emission are 21.7 g kWh^?1 for hydrogen compared with diesel of 17.9 g k Wh^?1. Smoke emissions reduced to 1 Bosch smoke number (BSN) in hydrogen compared with diesel of 2.2 BSN. Hydrogen operation in the dual fuel mode with diesel exhibits a better performance and reduction in emissions compared with diesel in the entire load spectra. Copyright © 2009 John Wiley & Sons, Ltd.     

Assessment of the method for calculating the Lewis number of H2/CO/CH4 mixtures and comparison with experimental results

This paper investigates the various techniques used in the literature to calculate the effective Lewis number of two-component (H₂/CO and H₂/CH₄) and three-component fuels (H₂/CO/CH₄ and H₂/CO/CO₂) over a wide range of equivalence ratios (0.6 ≤ φ ≤ 1.4) under laminar flame conditions. The most appropriate effective Lewis number formulation is identified through comparison with experimentally extracted Lewis numbers (Le). The paper first identifies the proper methodology to extract the experimental Le from the burned Markstein length of an outwardly propagating flame. Second, the different methodologies for the calculation of the effective Le are presented and compared to experimental results for H₂/CH₄ and H₂/CO mixtures. Based on the experimental results, it is shown that the calculation of the effective Le of mixtures can be divided into a three-step procedure depending on the equivalence ratio: (1) calculation of the Le for each fuel and the oxidizer; (2) use of the Le mixing rule; and (3) assessment of the necessity or not of combining the fuel's and oxidizer's Lewis numbers. The paper shows that, in rich mixtures, the oxidizer Le needs to be taken into account. Lastly, the methodology is validated for H₂/CO/CH₄ and H₂/CO/CO₂ fuels.     

The effect of biodiesel and bioethanol blended diesel fuel on nanoparticles and exhaust emissions from CRDI diesel engine

Biofuel (biodiesel, bioethanol) is considered one of the most promising alternative fuels to petrol fuels. The objective of the work is to study the characteristics of the particle size distribution, the reaction characteristics of nanoparticles on the catalyst, and the exhaust emission characteristics when a common rail direct injection (CRDI) diesel engine is run on biofuel-blended diesel fuels. In this study, the engine performance, emission characteristics, and particle size distribution of a CRDI diesel engine that was equipped with a warm-up catalytic converters (WCC) or a catalyzed particulate filter (CPF) were examined in an ECE (Economic Commission Europe) R49 test and a European stationary cycle (ESC) test. The engine performance under a biofuel-blended diesel fuel was similar to that under D100 fuel, and the high fuel consumption was due to the lowered calorific value that ensued from mixing with biofuels. The use of a biodiesel–diesel blend fuel reduced the total hydrocarbon (THC) and carbon monoxide (CO) emissions but increased nitrogen oxide (NO_x) emissions due to the increased oxygen content in the fuel. The smoke emission was reduced by 50% with the use of the bioethanol–diesel blend. Emission conversion efficiencies in the WCC and CPF under biofuel-blended diesel fuels were similar to those under D100 fuel. The use of biofuel-blended diesel fuel reduced the total number of particles emitted from the engine; however, the use of biodiesel–diesel blends resulted in more emissions of particles that were smaller than 50 nm, when compared with the use of D100. The use of a mixed fuel of biodiesel and bioethanol (BD15E5) was much more effective for the reduction of the particle number and particle mass, when compared to the use of BD20 fuel.     

Experimental investigation on a DI dual fuel engine with hydrogen injection

Over the past two decades considerable efforts have been undertaken to develop and introduce new alternative fuels for the conventional gasoline and diesel. Many alternative fuels, both liquid and gaseous, have been experimented and some have even been commercialized such as ethanol, natural gas, etc. Hydrogen has been considered as an excellent fuel to replace the petroleum‐based fuels due to its clean burning characteristics. In the present experimental investigation, hydrogen was injected in the intake manifold and diesel fuel was injected inside the engine cylinder in the conventional manner. Hydrogen injection parameters such as injection timing, injection duration and quantity of hydrogen injected were optimized based on the performance and emission characteristics. Exhaust gas recirculation (EGR) technique was adopted to reduce the oxides of nitrogen emission. From the results it was observed that for hydrogen diesel dual fuel (DF) engine, the optimal operating parameters for hydrogen injection were start of injection at gas exchange top dead centre with injection duration of 30° crank angle with the hydrogen flow rate of 7.5 litres per minute (lpm). With EGR the optimized condition was found to be 20% for the entire load. The brake thermal efficiency with 20% EGR increases by 16% at 75% load as compared with diesel, while at full load it reduces by 8% due to the recirculation of exhaust gases that results in a reduction of intake oxygen concentration compared with part load. NO_X emission decreases by five and half times, while other emissions increase by 1.4 times as compared with DF engine. Copyright © 2008 John Wiley & Sons, Ltd.     

Promotion of bio oil,H2 gas from the pyrolysis of rice husk assisted with nano silver catalyst and utilization of bio oil blend in CI engine

This paper reports on the pyrolytic distillation of rice husk with catalyst and its influence on both condensable and non-condensable volatiles. The catalyst used for pyrolysis was nano sized silver particles obtained through chemical reduction method. The structural features of the nano silver particles were explored through X-ray diffraction (XRD) and Field Emission Scanning Electron Microscope (FESEM) with Energy-dispersive-X-ray spectroscope (EDX), and the size of the nano particles was confirmed as 90 nm. After intimately mixing the rice husk (30 g) with the catalyst, the pyrolysis at various temperatures (400 °C, 450 °C, 500 °C, 550 °C) was performed. The products obtained during catalytic pyrolysis like gaseous fuel, bio oil, and bio char were separately collected and characterized through Gas Chromatography-Mass Spectrometer (GC-MS) and Inductively Coupled Plasma – Optical Emission Spectrometer (ICP-OES). About 50% of the solid biomass was converted into more useful liquid and gaseous fuel. It was noticed that during catalytic pyrolysis, the quantity of H₂ obtained was more (19.12%) in contrast to thermal pyrolysis and could be attributable to the influence of silver nano particles towards the enhancement in hydrogen gas production. The liquid hydrocarbon obtained during the catalytic distillation was blended with diesel in the ratio 20:80 in the compression ignition (CI) engine. The quality of the blended bio oil was assessed from brake thermal efficiency (BTE), brake specific fuel consumption (BSFC) and emission of nitrogen oxides (NO_X), carbon monoxide (CO) and unburnt hydrocarbon (UHC). At full load, the diesel fuel emitted 1780 ppm of NO_x while the diesel blended with bio oil emitted only 1510 ppm which was 15.17% less than the diesel oil which proved its eco-friendly nature. In future, the bio oil obtained from catalytic pyrolysis can be used as a blend for diesel oil, since it reduces NO_x emission and replaces 20% of diesel oil.     

An outcome of quaternary fuel blended Fe3O4-doped reduced graphene oxide nanocomposite on the diesel engine

The study includes the use of alcohols in conjunction with diesel as a binary fuel and biodiesel. In addition, this study was conducted on quaternary fuels (premium diesel, waste cooking biodiesel, n-butanol, and bioethanol), including Fe₃O₄ (iron(III) oxide)-doped reduced graphene oxide (rGO) nanocomposite to reduce the use of fossil fuels, their cost, and energy demand. It includes 10% bioethanol, 5%–20% n-butanol, 25 ppm Fe₃O₄-doped rGO nanocomposite, and 20% and 100% waste cooking biodiesel, all of which have been tested in a diesel engine to ensure that they are suitable for use. The findings were compared to those obtained with premium diesel, ranging from 50% to 100% at full engine load conditions. In comparison to 100% premium diesel fuel, the fuel blend (Blend G) had 37.50% brake thermal efficiency and 0.46% (brake-specific energy consumption), as well as lower rates of 316.2% carbon monoxide, 198.80% hydrocarbon, and 80.01% smoke with 28.10% higher oxides of nitrogen (NOx). Adding 20% n-butanol to premium diesel, as well as waste cooking biodiesel, bioethanol, and Fe₃O₄-doped rGO nanocomposite fuel blends, was used in this study to improve the performance of the diesel engine and reduce some of the NOx emissions. In the near future, these fuel blends may be a viable alternative combination for the diesel engine.     

Preparation,characterization, engine combustion and emission characteristics of rapeseed oil based hybrid fuels

In this study, hybrid fuels consisting of rapeseed oil/diesel blend, 1% aqueous ethanol and a surfactant (oleic acid/1-butanol mixture) were prepared and tested as a fuel in a direct injection (DI) diesel engine. The main fuel properties such as the density, viscosity and lower heating value (LHV) of these fuels were measured, and the engine performance, combustion and exhaust emissions were investigated and compared with that of diesel fuel. The experimental results showed that the viscosity and density of the hybrid fuels were decreased and close to that of diesel fuel with the increase of ethanol volume fraction up to 30%. The start of combustion was later than that of diesel fuel and the peak cylinder pressure, peak pressure rise rate and peak heat release rate were higher than those of diesel fuel. The brake specific fuel consumption (BSFC) of hybrid fuels was increased with the volume fraction of ethanol and higher than that of diesel. The brake specific energy consumption (BSEC) was almost identical for all test fuels. The smoke emissions were lower than those for diesel fuel at high engine loads, the NO_x emissions were almost similar to those of diesel fuel, but CO and HC emissions were higher, especially at low engine loads.