Role of Support in Lean DeNOx Catalysis

FTIR and pulse thermal analysis were applied to investigate catalysts containing Pt (1 wt%)/Ba (17 wt%) supported on -Al₂O₃, SiO₂ and ZrO₂. The aim was to learn how the support material affects the thermal stability of barium carbonate and its activity in the reaction to bulk Ba(NO₃)₂. The lower thermal stability of BaCO₃ in alumina supported samples was found to influence the formation of barium nitrate during the NO _x storage process. Quantification of Ba(NO₃)₂ formed during NO _x storage indicated that for alumina supported catalysts only ca. 30% of barium present in the sample is involved in the storage process. The low thermal stability found for alumina supported barium nitrite excludes its role in the formation of barium nitrate during interaction of NO _x with the catalyst at 300 °C. The studies indicate that -Al₂O₃ plays a major role in influencing the thermal stability of BaCO₃ and Ba(NO₃)₂. This finding seems to be relevant for the higher activity of -Al₂O₃-supported catalysts in NO _x storage reduction reactions.     

Characterisation by TPR, XRD and NOx Storage Capacity Measurements of the Ageing by Thermal Treatment and SO2 Poisoning of a Pt/Ba/Al NOx-Trap Model Catalyst

The deactivation of a Pt/Ba/Al₂O₃ NO _x -trap model catalyst submitted to SO₂ treatment and/or thermal ageing at 800 °C was studied by H₂ temperature programmed reduction (TPR), X-ray diffraction (XRD) and NO _x storage capacity measurements.The X-ray diffractogram of the fresh sample exhibits peaks characteristic for barium carbonate. Thermal ageing leads to the decomposition of barium carbonate and to the formation of BaAl₂O₄. The TPR profile of the sulphated sample shows the presence of (i) surface aluminium sulphates, (ii) surface barium sulphates, (iii) bulk barium sulphates. The exposure to SO₂ after ageing leads to a small decrease of the surface barium-based sulphates, expected mainly as aluminate barium sulphates. This evolution can be attributed to a sintering of the storage material. TPR experiments also show that thermal treatment at 800 °C after the exposure to SO₂ involves the decomposition of aluminium surface sulphates to give mainly bulk barium sulphates, also pointed out by XRD. Thus, the thermal treatment at 800 °C leads to a stabilization of the sulphates.These results are in accordance with the NO _x storage capacity measurements. On non-sulphated catalysts, the treatment at 800 °C induces to a decrease of the NO _x storage capacity, showing that barium aluminate presents a lower NO _x storage capacity than barium carbonate. Sulphation strongly decreases the NO _x storage capacity of catalysts, whatever the initial thermal treatment, showing that barium sulphates inhibit the NO₂ adsorption. Moreover, the platinum activity for the NO to NO₂ oxidation is lowered by thermal treatments.     

An XRD, FTIR and TPD Investigation of NO2 Surface Adsorption Sites of δ, γ Al2O3 and Barium Supported δ, γ Al2O3

In this paper an XRD, FTIR and TPD investigation of NO₂ surface adsorption sites of , Al₂O₃ and barium supported , Al₂O₃ is reported. Aim of this study is to bring additional light on the surface structures involved in NOx adsorption. Two samples of barium supported aluminas have been prepared and aged at 800 °C. These samples were characterised in comparison with the relative alumina support. The XRD characterisation of these samples shows the presence of barium carbonate and barium aluminate supported on alumina. The comparison of the FTIR spectra, before and after NO₂ adsorption, has revealed the formation, upon NO₂ contact, of a complex variety of nitrate and nitrite groups. The thermal desorption of nitrate and nitrite species has been simultaneously studied by means of FTIR spectroscopy and by TPD technique. By comparing the structural, adsorptive and spectroscopic results obtained on alumina and on barium supported alumina samples, a hypothesis on the basic sites active in NO₂ adsorption and of the possible decomposition paths induced by thermal heating are proposed.     

NOx storage behavior and sulfur-resisting performance of the third-generation NSR catalysts Pt/K/TiO2–ZrO2

The NO_x storage and reduction (NSR) catalysts Pt/K/TiO₂–ZrO₂ were prepared by an impregnation method. The techniques of XRD, NH₃-TPD, CO₂-TPD, H₂-TPR and in situDRIFTS were employed to investigate their NO_x storage behavior and sulfur-resisting performance. It is revealed that the storage capacity and sulfur-resisting ability of these catalysts depend strongly on the calcination temperature of the support. The catalyst with theist support calcined at 500 °C, exhibits the largest specific surface area but the lowest storage capacity. With increasing calcination temperature, the NO_x storage capacity of the catalyst improves greatly, but the sulfur-resisting ability of the catalyst decreases. In situ DRIFTS results show that free nitrate species and bulk sulfates are the main storage and sulfation species, respectively, for all the catalysts studied. The CO₂-TPD results indicate that the decomposition performance of K₂CO₃ is largely determined by the surface property of the TiO₂–ZrO₂ support. The interaction between the surface hydroxyl of the support and K₂CO₃ promotes the decomposition of K₂CO₃ to form –OK groups bound to the support, leading to low NO_x storage capacity but high sulfur-resisting ability, while the interaction between the highly dispersed K₂CO₃ species and Lewis acid sites gives rise to high NO_x storage capacity but decreased sulfur-resisting ability. The optimal calcination temperature of TiO₂–ZrO₂ support is 650 °C.     

Changes in Ba Phases in BaO/Al2O3 upon Thermal Aging and H2O Treatment

The effects of thermal aging and H₂O treatment on the physicochemical properties of BaO/Al₂O₃ (the NO_x storage component in the lean NO_x trap systems) were investigated by means of X-ray diffraction (XRD), BET, TEM/EDX and NO₂ TPD. Thermal aging at 1000 °C for 10 h converted dispersed BaO/BaCO₃ on Al₂O₃ into low surface area crystalline BaAl₂O₄. TEM/EDX and XRD analysis showed that H₂O treatment at room temperature facilitated a dissolution/reprecipitation process, resulting in the formation of a highly crystalline BaCO₃ phase segregated from the Al₂O₃ support. Crystalline BaCO₃ was formed from conversion of both BaAl₂O₄ and a dispersed BaO/BaCO₃ phase, initially present on the Al₂O₃ support material after calcinations at 1000 and 500 °C, respectively. Such a phase change proceeded rapidly for dispersed BaO/BaCO₃/Al₂O₃ samples calcined at relatively low temperatures with large BaCO₃ crystallites observed in XRD within 10 min after contacting the sample with water. Significantly, we also find that the change in barium phase occurs even at room temperature in an ambient atmosphere by contact of the sample with moisture in the air, although the rate is relatively slow. These phenomena imply that special care to prevent the water contact must be taken during catalyst synthesis/storage, and during realistic operation of Pt/BaO/Al₂O₃ NO_x trap catalysts since both processes involve potential exposure of the material to CO₂ and liquid and/or vapor H₂O. Based on the results, a model that describes the behavior of Ba-containing species upon thermal aging and H₂O treatment is proposed.     

Influence of CO2 on storage and release of NOx on barium‐containing catalyst

A barium‐containing three‐way automotive emission catalyst was submitted to a NO_x storage step in flowing lean gas mixture containing 340 ppm NO and 8 vol% O₂ in helium. NO_x release was carried out in the 250–550°C temperature range, either in pure helium or in the presence of a 10 vol% CO₂ in helium mixture. It was shown that at 450–550°C all of the stored NO_x on the barium trap can be released fastly in the CO₂‐containing gas mixture or, after a longer time, in pure helium: these data show that NO_x release can occur in the absence of a reducing agent. The NO_x release was not complete at 350°C and did not occur at 250°C. The assisting effect of CO₂ as regards to NO_x release was interpreted in terms of the existence of the CO_2,gas + *NO_2,stored ⇌ *CO_2,stored + NO_2,gas equilibrium, suggesting the competitive storage of CO₂ and NO₂ for a unique type of barium storage sites (*). This revised version was published online in July 2006 with corrections to the Cover Date.     

Fundamental Investigations of Thermal Aging Phenomena of Model NOx Storage Systems

Investigations of the aging behavior induced by high temperatures coupled with oxidizing atmosphere of model NO _x storage systems Ba/Al₂O₃ and Ba/CeO₂ are reported in this paper. The samples were prepared, calcined and exposed to temperatures between 500 and 1000 °C in air for 12 h for thermal aging. Samples were characterized with XRD, HRSEM, DSC-TGA-MS and BET analyses. In XRD investigations of all model systems calcined at 500 °C for 2 h, the NO _x storage component was present in form of BaCO₃. The release of CO₂ as a result of the decarbonization of the NO _x storage component at increased temperatures was verified by thermogravimetric investigations. In the case of Ba/Al₂O₃, already during calcination a partial reaction of the NO _x storage component with Al₂O₃ resulting in the formation of barium aluminate was observed. In the model system Ba/CeO₂ the decomposition of the barium carbonate started above 780 °C and the formation of a barium cerium mixed oxide was observed. The presence of the barium containing NO _x storage component has a strong influence on the specific surface area of the model NO _x storage systems. The morphology and crystallite size of CeO₂ modified with the barium containing NO _x storage component exhibited distinct changes compared to the unmodified oxide. The NO _x storage efficiency determined by model gas tests of freshly prepared and engine aged model NO _x storage catalysts correlates well with the above described observations.     

Model for NOx storage/reduction in the presence of CO2 on a Pt–Ba/γ-Al2O3 catalyst

We have constructed a global reaction kinetic model to better understand and describe the NO_x storage/reduction process in the presence of CO₂. Experiments were performed in a packed-bed reactor with a Pt–Ba/γ-Al₂O₃ powder catalyst (1 wt% Pt and 30 wt% Ba) with different lean/rich cycle timings. The model is based on a multiple storage sites mechanism and considers that fast NO_x storage occurs at surface barium sites, as determined by the reaction kinetics. Slow NO_x storage occurs at the semi-bulk and bulk barium sites, where diffusion plays a major role. It is assumed that surface, bulk, and semi-bulk sites differ not only in physical appearance, but also in chemical reactivity. The distribution of these sites is obtained from 9-h lean-phase and 15-h rich-phase cycling experiments and thermogravimetric analysis of fresh catalyst. The model adequately describes the NO and NO₂ breakthrough profiles during 9 h of lean exposure, as well as the subsequent release and reduction of the stored NO_x. Furthermore, the model is also capable of simulating transient reactor experiments with 240-s lean-cycle and 60-s rich-cycle timings.     

Modelling of NOx adsorption over NOx adsorbers

Modelling of the phenomena involved during the adsorption of NO_x on NO_x trap catalysts was developed. The aim of the model is the prediction of the quantity of stocked barium nitrate as well as the emissions of NO and NO₂, as a function of time and temperature. The mechanism of the process is sounded on the adsorption of gas species (NO, NO₂, O₂) on platinum sites, equilibrium reaction between adsorbed species followed by the formation of Ba(NO₃)₂. This formation of barium nitrate is limited by the thermal decomposition reaction which liberates NO in the gas phase. The kinetic constant of decomposition of barium nitrate was determined by temperature programmed thermogravimetry on pure Ba(NO₃)₂, using the method of Freeman and Carroll. Other kinetic constants bound to the mechanism were estimated by fitting the results of the model to experimental results.The mechanism was validated for various values of the molar fraction of O₂, the molar fraction of NO and various values of the NO/NO₂ ratio in the gas entering the reactor. It was also tested with different catalyst compositions (variation of the platinum and BaO concentrations). The importance of oxygen in the process was clearly demonstrated as well as the promoting role of NO₂.     

NO x uptake mechanism on Pt/BaO/Al2O3 catalysts

The NO _x adsorption mechanism on Pt/BaO/Al₂O₃ catalysts was investigated by performing NO _x storage/reduction cycles, NO₂ adsorption and NO + O₂ adsorption on 2%Pt/(x)BaO/Al₂O₃ (x = 2, 8, and 20 wt%) catalysts. NO _x uptake profiles on 2%\Pt/20%BaO/Al₂O₃ at 523 K show complete uptake behavior for almost 5 min, and then the NO _x level starts gradually increasing with time and it reaches 75% of the inlet NO _x concentration after 30 min time-on-stream. Although this catalyst shows fairly high NO _x conversion at 523 K, only ~2.4 wt% out of 20 wt% BaO is converted to Ba(NO₃)₂. Adsorption studies by using NO₂ and NO + O₂ suggest two different NO _x adsorption mechanisms. The NO₂ uptake profile on 2%Pt/20%BaO/Al₂O₃ shows the absence of a complete NO _x uptake period at the beginning of adsorption and the overall NO _x uptake is controlled by the gas–solid equilibrium between NO₂ and BaO/Ba(NO₃)₂ phase. When we use NO + O₂, complete initial NO _x uptake occurs and the time it takes to convert ~4% of BaO to Ba(NO₃)₂ is independent of the NO concentration. These NO _x uptake characteristics suggest that the NO + O₂ reaction on the surface of Pt particles produces NO₂ that is subsequently transferred to the neighboring BaO phase by spill over. At the beginning of the NO _x uptake, this spill-over process is very fast and so it is able to provide complete NO _x storage. However, the NO _x uptake by this mechanism slows down as BaO in the vicinity of Pt particles are converted to Ba(NO₃)₂. The formation of Ba(NO₃)₂ around the Pt particles results in the development of a diffusion barrier for NO₂, and increases the probability of NO₂ desorption and consequently, the beginning of NO _x slip. As NO _x uptake by NO₂ spill-over mechanism slows down due to the diffusion barrier formation, the rate and extent of NO₂ uptake are determined by the diffusion rate of nitrate ions into the BaO bulk, which, in turn, is determined by the gas phase NO₂ concentration.     

Fundamental studies of NOx storage at low temperatures

A commercial NO_x storage catalyst (Pt, BaO and alumina containing) was investigated by temperature programmed desorption (TPD) experiments in the temperature range 100–400 °C. The catalyst stored a substantial amount of NO_x at 100 °C using NO + O₂. Nitrites or loosely bound NO species are suggested for this storage, since no NO was oxidised at this low temperature. In addition, the released NO_x during the temperature ramp consisted of mainly NO and at lower temperatures the NO₂ dissociation is limited. Water and CO₂ was found to decrease the storage substantially, 92% for the NO + O₂ adsorption at 100 °C. The total storage for 60 min using NO₂ + O₂ at 200 °C was similar when introducing CO₂ and H₂O. However, the initial total uptake of NO_x was decreased. Initially we probably formed loosely bound NO_x species, which likely are strongly influenced by water and CO₂. After longer time periods are barium nitrates probably formed and they can remove the carbonates by forming stable nitrates, thus resulting in the same total uptake of NO_x.     

Model Studies of NOx Storage and Sulphur Deactivation of NOx Storage Catalysts

The storage of NO _x under lean conditions in model NO _x storage catalysts as well as the deactivation by sulphur have been studied. We find that NO₂ plays an important role in the storage mechanism as an oxidising agent. Two different mechanisms for this are discussed: the formation of surface peroxides and the oxidation of nitrites to nitrates. FTIR studies show that NO _x is stored as surface nitrates. The sulphur deactivation is found to be more severe when SO₂ is added during the rich phase than when SO₂ is added during the lean period. FTIR shows the formation of bulk sulphates both under lean and rich conditions.     

Promotional Effects of H2O Treatment on NO x Storage Over Fresh and Thermally Aged Pt–BaO/Al2O3 Lean NO x Trap Catalysts

A simple liquid water treatment applied to fresh and thermally aged Pt(2 wt%)–BaO(20 wt%)/Al₂O₃ lean NO _x trap catalysts at room temperature induces morphological and structural changes in the barium species as followed by XRD and TEM analysis. During the water treatment, liquid water sufficient to fill the catalyst pore volume is brought into contact with the samples. It was found that irrespective of the original barium chemical state (highly dispersed BaO or crystalline BaAl₂O₄), exposing the sample to this liquid water treatment promotes the formation of BaCO₃ crystallites (about 15–25 nm of its size) without changing the Pt particle size. Such transformations of the barium species are found to significantly promote NO _x uptake from 250 to 450 °C. The increase in the NO _x uptake for the water-treated samples can be attributed to an enhanced Pt–Ba interaction through the redistribution of barium species. These results provide useful information for the regeneration of aged lean NO _x trap catalysts since water is plentiful in the exhaust of diesel or lean-burn engines.     

Sulfur deactivation and regeneration of Pt/BaO/Al2O3 and Pt/SrO/Al2O3 NO x storage catalysts

Transient experiments were performed to study sulfur deactivation and regeneration of Pt/BaO/Al₂O₃ and Pt/SrO/Al₂O₃ NO _x storage catalysts. It was found that the strontium-based catalysts are more easily regenerated than the barium-based catalysts and that a higher fraction of the NO _x storage sites are regenerated when H₂ is used in combination with CO₂ compared to H₂ only.     

The mechanism for NOx storage

The mechanisms for storing of NO_x in platinum–barium–alumina catalysts during lean–rich transients are investigated. Oxidation of NO to NO₂ is found to be an important step. NO₂ is found to be important for oxidation of the catalyst or of nitrites to form nitrates. NO_x is then stored in the form of surface nitrates. FTIR studies show no formation of bulk nitrates in these experiments. This revised version was published online in July 2006 with corrections to the Cover Date.     

The Effects of CO2 and H2O on the NO x Destruction Performance of a Model NO x Storage/Reduction Catalyst

The effects of CO₂ and H₂O on the NO _x storage and reduction characteristics of a Pt/Ba/Al₂O₃ catalyst were investigated. The presence of CO₂ and H₂O, individually or together, affect the performance and therefore the chemistry that occurs at the catalyst surface. The effects of CO₂ were observed in both the trapping and reduction phases of the experiments, whereas the effect of H₂O seems limited to the trapping phase. The data also indicate that multiple types of sorption sites (or mechanisms for sorption) exist on the catalyst. One mechanism is characterized by a rapid and complete uptake of NO _x . A second mechanism is characterized by a slower rate of NO _x uptake, but this mechanism is active for a longer time period. As the temperature is increased, the effect of H₂O decreases compared to that of CO₂. At the highest temperatures examined, the elimination of H₂O when CO₂ is present did not affect the performance.     

Excellent sulfur resistance of Pt/BaO/CeO2 lean NOx trap catalysts

In this work, we investigated the NO_x storage behavior of Pt/BaO/CeO₂ catalysts, especially in the presence of SO₂. High surface area CeO₂ (110 m²/g) with a rod like morphology was synthesized and used as a support. The Pt/BaO/CeO₂ sample demonstrated slightly higher NO_x uptake in the entire temperature range studied compared with Pt/BaO/γ-Al₂O₃. More importantly, this ceria-based catalyst showed higher sulfur tolerance than the alumina-based one. The time of complete NO_x uptake was maintained even after exposing the sample to 3 g/L of SO₂. The same sulfur exposure, on the other hand, eliminated the complete NO_x uptake time on the alumina-based NO_x storage catalysts. TEM images show no evidence of either Pt sintering or BaS phase formation during reductive de-sulfation up to 600 °C on the ceria-based catalyst, while the same process over the alumina-based catalyst resulted in both a significant increase in the average Pt cluster size and the agglomeration of a newly formed BaS phase into large crystallites. XPS results revealed the presence of about five times more residual sulfur after reductive de-sulfation at 600 °C on the alumina-based catalysts in comparison with the ceria-based ones. All of these results strongly support that, besides their superior intrinsic NO_x uptake properties, ceria-based catalysts have (a) much higher sulfur tolerance and (b) excellent resistance against Pt sintering when they are compared to the widely used alumina-based catalysts.     

Performance of potassium-promoted catalysts for NO x and soot removal from simulated diesel exhaust

In order to elucidate the effect of support in the catalytic performance, two selected potassium-promoted catalysts (K1Cu/beta and KCu2/Al₂O₃) were tested for the simultaneous NO _x /soot removal from a simulated diesel exhaust. For comparative purpose, the behaviour of a platinum catalyst (Pt/beta) was also studied. Isothermal experiments revealed that the potassium-promoted catalysts show a high activity for NO _x /soot removal in the 350–450 °C temperature range. In addition, the catalysts present the advantage that the main reaction products are N₂ and CO₂. Among the catalysts tested, KCu2/Al₂O₃ presents the best global performance at 450 °C: the highest soot consumption rate, even higher than the platinum catalysts, and a high NO _x reduction.     

Influence of the Storage Material on the Storage of NOx at Low Temperatures

The NO _x storage performance at low temperature (100–200 °C) has been studied for model NO _x storage catalysts. The catalysts were prepared by sequentially depositing support, metal oxide and platinum on ceramic monoliths. The support material consisted of acidic aluminium silicate, alumina or basic aluminium magnesium oxide, and the added metal oxide was either ceria or barium oxide. The NO _x conversion was evaluated under net-oxidising conditions with transients between lean and rich gas composition and the NO _x storage performance was studied by isothermal adsorption of NO₂ followed by temperature programmed desorption of adsorbed species. The maximum in NO _x storage capacity was observed at 100 °C for all samples studied. The Pt/BaO/Al₂O₃ catalyst stored about twice the amount of NO _x compared with the Pt/Al₂O₃ and Pt/CeO₂/Al₂O₃ samples. The storage capacity increased with increasing basicity of the support material, i.e. Pt/Al₂O₃·SiO₂ < Pt/Al₂O₃ < Pt/Al₂O₃ · MgO. Water did not significantly affect the NO _x storage performance for Pt/Al₂O₃ or Pt/BaO/Al₂O₃.     

Characterization of uniform,nanodispersed NOx storage catalyst materials synthesized by successive ionic layer deposition

A dispersed phase of barium oxide (BaO) supported on alumina has been shown to be primarily responsible for NO_x storage in practical lean NO_x trap catalysts. Conventional impregnation based catalyst loading techniques generate a mixture of dispersed and less active bulk-like BaO phases on alumina, with the bulk-like phase increasing as weight loading increases. Samples of equivalent BaO weight loading on fused alumina were prepared by successive ionic layer deposition (SILD) and wet impregnation. NO₂ temperature programmed desorption experiments demonstrate that SILD is uniquely capable of selectively synthesizing uniform, nanodispersed BaO rafts with high surface coverage. These nanodispersed SILD structures show remarkable thermal stability under high operating temperatures up to 650 °C.