Thermoelectric Properties of <Emphasis Type="Italic">p</Emphasis>-Type Mg<Subscript>2.00</Subscript>Si<Subscript>0.25</Subscript>Sn<Subscript>0.75</Subscript> with Li and Ag Double Doping

Mg₂Si_1−x Sn _x -system solid solutions are ecofriendly semiconductors that are promising materials for thermoelectric generators in the middle temperature range. To produce a thermoelectric device, high-performance p- and n-type materials must be balanced. In this paper, p-type Mg_2.00Si_0.25Sn_0.75 with Li and Ag double doping was prepared by the liquid–solid reaction method and hot-pressing. Effects of Li and Ag double doping on thermoelectric properties were investigated in the temperature range from room temperature to 850 K. All sintered compacts were identified as single-phase solid solutions with anti-fluorite structure. The carrier concentration increased with the double doping. The temperature dependence of resistivity of the double-doped samples was similar to that of a metal. The seebeck coefficient increased with temperature to a maximum value and then decreased in the intrinsic region. Thermal conductivity decreased linearly with increasing temperature, reaching a minimum near the intrinsic region, and then increased rapidly because of the contribution of the bipolar component. The dimensionless figure of merit reached 0.32 at 610 K for Mg_2.00Si_0.25Sn_0.75 double-doped with Li-5000 ppm and Ag-20000 ppm.     

Preparation and Thermoelectric Properties of LaGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript> and SmGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript>

Thermoelectric materials are attractive since they can recover waste heat directly in the form of electricity. In this study, the thermoelectric properties of ternary rare-earth sulfides LaGd_1+x S₃ (x = 0.00 to 0.03) and SmGd_1+x S₃ (x = 0.00 to 0.06) were investigated over the temperature range of 300 K to 953 K. These sulfides were prepared by CS₂ sulfurization, and samples were consolidated by pressure-assisted sintering to obtain dense compacts. The sintered compacts of LaGd_1+x S₃ were n-type metal-like conductors with a thermal conductivity of less than 1.7 W K⁻¹ m⁻¹. Their thermoelectric figure of merit ZT was improved by tuning the chemical composition (self-doping). The optimized ZT value of 0.4 was obtained in LaGd_1.02S₃ at 953 K. The sintered compacts of SmGd_1+x S₃ were n-type hopping conductors with a thermal conductivity of less than 0.8 W K⁻¹ m⁻¹. Their ZT value increased significantly with temperature. In SmGd_1+x S₃, the ZT value of 0.3 was attained at 953 K.     

Effect of Sb Doping on the Thermoelectric Properties of Mg<Subscript>2</Subscript>Si<Subscript>0.7</Subscript>Sn<Subscript>0.3</Subscript> Solid Solutions

This study focuses on Sb-doped Mg₂(Si,Sn) thermoelectric material. Samples were successfully fabricated using a hybrid synthesis method consisting of three different processes: induction melting, solid-state reaction, and a hot-press sintering technique. We found that the carrier concentration increased with Sb content, while the Seebeck coefficient exhibited a decreasing trend. Sb doping was shown to improve the power factor and thermoelectric figure of merit compared with the undoped material, yielding a peak figure of merit (ZT) of ~0.55 at 620 K, while leaving the band gap of Mg₂Si_0.7Sn_0.3 almost unchanged.     

Thermal Conductivity of Bi<Subscript>0.5</Subscript>Sb<Subscript>1.5</Subscript>Te<Subscript>3</Subscript> Affected by Grain Size and Pores

A fine measurement system for measuring thermal conductivity was constructed. An accuracy of 1% was determined for the reference quartz with a value of 1.411 W/m K. Bi_0.5Sb_1.5Te₃ samples were prepared by mechanical alloying followed by hot-pressing. Grain sizes were varied in the range from 1 μm to 10 μm by controlling the sintering temperature in the temperature range from 623 K to 773 K. The thermal conductivity was 0.89 W/m K for the sample sintered at 623 K, while a grain size of 1.75 μm was measured by optical microscopy and scanning electron microscopy. The thermal conductivity increased on the sample sintered at 673 K because of grain growth and decreased on those sintered at the temperatures from 673 K to 773 K because the increase of pore size caused to decrease thermal conductivity. The increase of thermal conductivity for the samples sintered at temperatures above 773 K was affected by the increase of carrier concentration.     

Crystal Structure and High-Temperature Thermoelectric Properties of the Mo<Subscript>3−<Emphasis Type="Italic">x</Emphasis></Subscript>Ru<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Sb<Subscript>7</Subscript> Compounds

Zintl phases are currently receiving great attention for their thermoelectric potential typified by the discovery of a high ZT value in Yb₁₄MnSb₁₁-based compounds. Herein, we report on the crystallographic characterization via neutron and x-ray diffraction experiments, and on the thermoelectric properties measured in the 300 K to 1000 K temperature range, of Mo₃Sb₇ and its isostructural compounds Mo_3−x Ru _x Sb₇. Even though Mo₃Sb₇ displays rather high ZT values given its metallic character, the partial substitution of Mo by Ru substantially improves its thermoelectric properties, resulting in a ZT value of ∼0.45 at 1000 K for x = 0.8.     

High Power Factor of HPHT-Sintered GeTe-AgSbTe<Subscript>2</Subscript> Alloys

The thermopower and electrical resistivity of alloys of GeTe and AgSbTe₂ (TAGS) sintered at high pressure (up to 4.5 GPa) and high temperature (HPHT) have been studied from 300 K to 750 K. An apparatus for measuring thermopower and electrical resistivity at temperatures >300 K is described. The linear temperature dependence of thermopower and electrical conductivity indicates that these materials are likely to be degenerate semiconductors. At a sintering pressure of 4.0 GPa, the calculated power factor shows a steady progression, reaching a maximum at a sintering temperature of 800°C, with a subsequent decrease at the highest sintering temperature of 850°C. The maximum power factor of 4.32 × 10⁻³ W m⁻¹ K⁻² at ~675 K is ~25% higher than reported values. These results illustrate that HPHT processing is a feasible and controllable way of tuning the properties of thermoelectric materials.     

Cage-Shaped Mo<Subscript>9</Subscript> Chalcogenides: Promising Thermoelectric Materials with Significantly Low Thermal Conductivity

Thermoelectric properties of molybdenum selenides containing Mo₉ clusters have been investigated between 300 K and 800 K. Ag _x Mo₉Se₁₁ (x = 3.4 and 3.8) have been synthesized by solid-state reaction and spark plasma sintering. X-ray diffraction and scanning electron microscopy reveal high purity and good homogeneity of the samples. The thermoelectric power of the samples is positive over the whole investigated temperature range, indicating that the majority of charge carriers are holes. The Seebeck coefficient increases with temperature, and the temperature coefficient of the resistivity is positive. Significantly low thermal conductivity, comparable to values reported for state-of-the-art thermoelectric materials, is observed in this new system, and this is assumed to be associated with the rattling effect from the Ag filler atoms. It has been demonstrated that the electrical and thermal properties correlate to the Ag concentration. For x = 3.8, a promising dimensionless thermoelectric figure of merit of ∼0.7 is obtained at 800 K.     

Low-Temperature Thermoelectric Properties of Co<Subscript>0.9</Subscript>Fe<Subscript>0.1</Subscript>Sb<Subscript>3</Subscript>-Based Skutterudite Nanocomposites with FeSb<Subscript>2</Subscript> Nanoinclusions

Bulk thermoelectric nanocomposite materials have great potential to exhibit higher ZT due to effects arising from their nanostructure. Herein, we report low-temperature thermoelectric properties of Co_0.9Fe_0.1Sb₃-based skutterudite nanocomposites containing FeSb₂ nanoinclusions. These nanocomposites can be easily synthesized by melting and rapid water quenching. The nanoscale FeSb₂ precipitates are well dispersed in the skutterudite matrix and reduce the lattice thermal conductivity due to additional phonon scattering from nanoscopic interfaces. Moreover, the nanocomposite samples also exhibit enhanced Seebeck coefficients relative to regular iron-substituted skutterudite samples. As a result, our best nanocomposite sample boasts a ZT = 0.041 at 300 K, which is nearly three times as large as that for Co_0.9Fe_0.1Sb₃ previously reported.     

Thermoelectric Properties of NdGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript> Prepared by CS<Subscript>2</Subscript> Sulfurization

Ternary rare-earth sulfides NdGd_1+x S₃, where 0 ≤ x ≤ 0.08, were prepared by sulfurizing Ln₂O₃ (Ln = Nd, Gd) with CS₂ gas, followed by reaction sintering. The sintered samples have full density and homogeneous compositions. The Seebeck coefficient, electrical resistivity, and thermal conductivity were measured over the temperature range of 300 K to 950 K. All the sintered samples exhibit a negative Seebeck coefficient. The magnitude of the Seebeck coefficient and the electrical resistivity decrease systematically with increasing Gd content. The thermal conductivity of all the sintered samples is less than 1.9 W K⁻¹ m⁻¹. The highest figure of merit ZT of 0.51 was found in NdGd_1.02S₃ at 950 K.     

The Effect of High-Pressure Sintering Process on the Microstructure and Thermoelectric Properties of CoSb<Subscript>3</Subscript>

The high-pressure sintering process is studied for the fabrication of the bulk CoSb₃ thermoelectric material. The CoSb₃ powder is prepared by a solid reaction method, and then the samples are sintered under high-pressure conditions. The emphasis of the present study is on the influence of the pressure on the grain size and the electrical properties of the material. For the present study, the pressure is taken to be from 1.5 GPa to 6 GPa, and the sintering temperature is 723 K. The experimental results show that the major phase of skutterudite and traces of metal impurities of Sb and the CoSb₂ phase coexist in some of the samples, and that the grain size of all the samples increase after sintering. In the range of 3.0 GPa to 6.0 GPa, the grain size increases with increasing pressure. In the range of 1.5 GPa to 3.0 GPa, the grain size also increases, but with a diminishing growth rate. All the materials show p-type transport behaviors, and the sample sintered under 2.0 GPa shows higher electrical conductivity than the 5.7 GPa sample, which may be due to the impurities.     

Preparation and Thermoelectric Characterization of SiC-B<Subscript>4</Subscript>C Composites

SiC-B₄C composites with various values of SiC-to-B₄C ratio and grain size were fabricated by pressureless sintering. This paper presents the results of current investigations of this composite material. This includes the parameters of manufacture (shrinkage, density, and open porosity), thermoelectric properties (electrical and thermal conductivity, and thermopower), and material characterization (x-ray diffraction, scanning electron microscopy, oxidation resistance, and thermal expansion). The results indicate high potential of this composite as an alternative material for thermoelectric applications at high temperatures. The Seebeck coefficient of the composite was higher than that of the single-component materials B₄C and SiC and reached 400 μV/K at 500°C.     

Thermal Stability of Barium and Indium Double-Filled Skutterudite Ba<Subscript>0.3</Subscript>In<Subscript>0.2</Subscript>Co<Subscript>3.95</Subscript>Ni<Subscript>0.05</Subscript>Sb<Subscript>12</Subscript> Coated by SiO<Subscript>2</Subscript> Nanoparticles

Filled skutterudite thermoelectric (TE) materials have been extensively studied to search for better TE materials in the past decade. However, there is no detailed investigation about the thermal stability of filled skutterudite TE materials. The evolution of microstructure and TE properties of nanostructured skutterudite materials fabricated with Ba_0.3In_0.2Co_3.95Ni_0.05Sb₁₂/SiO₂ core–shell composite particles with 3 nm thickness shell was investigated during periodic thermal cycling from room temperature to 723 K in this work. Scanning electronic microscopy and electron probe microscopy analysis were used to investigate the microstructure and chemical composition of the nanostructured skutterudite materials. TE properties of the nanostructured skutterudite materials were measured after every 200 cycles of quenching in the temperature range from 300 K to 800 K. The results show that the microstructure and composition of Ba_0.3In_0.2Co_3.95Ni_0.05Sb₁₂/SiO₂ nanostructured skutterudite materials were more stable than those of single-phase Ba_0.3In_0.2Co_3.95Ni_0.05Sb₁₂ bulk materials. The evolution of TE properties indicates that the electrical and thermal conductivity decrease along with an increase in the Seebeck coefficient with increasing quenching up to 2000 cycles. As a result, the dimensionless TE figure of merit (ZT) of the nanostructured skutterudite materials remains almost constant. It can be concluded that these nanostructured skutterudite materials have good thermal stability and are suitable for use in solar power generation systems.     

Microstructures and Thermoelectric Properties of an Annealed Ti<Subscript>0.5</Subscript>(Hf<Subscript>0.5</Subscript>Zr<Subscript>0.5</Subscript>)<Subscript>0.5</Subscript>NiSn<Subscript>0.998</Subscript>Sb<Subscript>0.002</Subscript> Ribbon

The thermoelectric half-Heusler compound Ti_0.5(Hf_0.5Zr_0.5)_0.5NiSn_0.998Sb_0.002 was fabricated by spin-casting and subsequent annealing. ZT at room temperature increased with annealing time through an increase in absolute Seebeck coefficients despite a decrease in electrical conductivity. ZT reached 0.10 after annealing at 1050 K for 48 h. In powder x-ray diffraction analysis, each half-Heusler peak was accompanied by a bump at the high-angle side, corresponding to a minor Ti-rich half-Heusler phase. The quantity and Ti composition of the minor phase increased with annealing time, although those of the major half-Heusler phase were almost constant. In transmission electron microscopic analysis, granular domains, several nanometers in size, with atomic ordering or disordering were observed. Thermoelectric properties were␣improved by annealing through the growth of heterogeneous microstructures of the Ti-rich and Ti-poor half-Heusler grains and of the granular domains.     

Solid-State Synthesis of Te-Doped Mg<Subscript>2</Subscript>Si

Te-doped Mg₂Si (Mg₂Si:Te _m , m = 0, 0.01, 0.02, 0.03, 0.05) alloys were synthesized by a solid-state reaction and mechanical alloying. The electronic transport properties (Hall coefficient, carrier concentration, and mobility) and thermoelectric properties (Seebeck coefficient, electrical conductivity, thermal conductivity, and figure of merit) were examined. Mg₂Si was synthesized successfully by a solid-state reaction at 673 K for 6 h, and Te-doped Mg₂Si powders were obtained by mechanical alloying for 24 h. The alloys were fully consolidated by hot-pressing at 1073 K for 1 h. All the Mg₂Si:Te _m samples showed n-type conduction, indicating that the electrical conduction is due mainly to electrons. The electrical conductivity increased and the absolute value of the Seebeck coefficient decreased with increasing Te content, because Te doping increased the electron concentration considerably from 10¹⁶ cm⁻³ to 10¹⁸ cm⁻³. The thermal conductivity did not change significantly on Te doping, due to the much larger contribution of lattice thermal conductivity over the electronic thermal conductivity. Thermal conduction in Te-doped Mg₂Si was due primarily to lattice vibrations (phonons). The thermoelectric figure of merit of intrinsic Mg₂Si was improved by Te doping.     

Structural Phase Transitions and Thermoelectric Properties of AgPb<Subscript>18</Subscript>SbTe<Subscript>20</Subscript> Under Compression

The high-figure-of-merit thermoelectric material AgPb₁₈SbTe₂₀ has been investigated by in situ angular-dispersive x-ray diffraction (XRD) and x-ray absorption fine-structure (XAFS) measurements up to 30 GPa. Resistivity and thermopower were measured with Bridgman-type opposed metal anvil cells. The results show that the ambient cubic ( Fm[`3] m ) \left( {Fm\overline{3} m} \right) structure transforms to orthorhombic (Pnma) at 6.4 GPa and then to the CsCl-type ( Pm[`3] m ) \left( {Pm\overline{3} m} \right) structure at 15 GPa. The ambient cubic ( Fm[`3] m ) \left( {Fm\overline{3} m} \right) phase is found to be recoverable on releasing the pressure. The thermoelectric power is found to increase with pressure for the cubic phase. The XAFS studies performed at the Pb L ₃-edge and Ag K-edge along with resistivity studies complement the XRD findings.     

Effect of Transition-Metal Additives on Thermoelectric Properties of YB<Subscript>22</Subscript>C<Subscript>2</Subscript>N

The higher boride compound YB₂₂C₂N has been reported as a promising n-type high-temperature thermoelectric material and possible counterpart to boron carbide. To investigate the influence of transition-metal additives on the thermoelectric properties of YB₂₂C₂N, a series of Rh, Co, Cu, and Ni samples were prepared. The resistivity and Seebeck coefficient of the samples were measured in the temperature range of 323 K to 1073 K. Samples with Rh and Co additives showed a considerable reduction of resistivity in comparison with pure YB₂₂C₂N and maintained their semiconducting properties at high temperatures. A sample with Co, obtained using long-term ball milling, showed the highest absolute value of Seebeck coefficient among all previously studied YB₂₂C₂N-based materials. Analyses of the influence of transition-metal additives and processing methods such as ball milling on the thermoelectric properties of YB₂₂C₂N are presented.     

Synthesis and Thermoelectric Properties of the Double-Filled Skutterudite Yb<Subscript>0.2</Subscript>In<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript>Co<Subscript>4</Subscript>Sb<Subscript>12</Subscript>

Filled skutterudites have long been singled out as one of the prime examples of phonon glass electron crystal materials. Recently the double-filling approach in these materials has been attracting increased attention. In this study, Yb_0.2In _y Co₄Sb₁₂ (y = 0.0 to 0.2) samples have been prepared by a simple melting method and their thermoelectric properties have been investigated. The power factor is increased dramatically when increasing the In content, while the lattice thermal conductivity is lowered considerably, leading to a large increase of the ZT value. A state-of-the-art ZT value of 1.0 is attained in Yb_0.2In_0.2Co₄Sb₁₂ at 750 K.     

Thermoelectric Properties of In<Subscript>0.3</Subscript>Ga<Subscript>0.7</Subscript>N Alloys

We report on the experimental investigation of the potential of InGaN alloys as thermoelectric (TE) materials. We have grown undoped and Si-doped In_0.3Ga_0.7N alloys by metalorganic chemical vapor deposition and measured the Seebeck coefficient and electrical conductivity of the grown films with the aim of maximizing the power factor (P). It was found that P decreases as electron concentration (n) increases. The maximum value for P was found to be 7.3 × 10⁻⁴ W/m K² at 750 K in an undoped sample with corresponding values of Seebeck coefficient and electrical conductivity of 280 μV/K and 93␣(Ω cm)⁻¹, respectively. Further enhancement in P is expected by improving the InGaN material quality and conductivity control by reducing background electron concentration.     

Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript> Superlattices Grown by Nanoalloying

In this work, Bi₂Te₃-Sb₂Te₃ superlattices were prepared by the nanoalloying approach. Very thin layers of Bi, Sb, and Te were deposited on cold substrates, rebuilding the crystal structure of V₂VI₃ compounds. Nanoalloyed super- lattices consisting of alternating Bi₂Te₃ and Sb₂Te₃ layers were grown with a thickness of 9 nm for the individual layers. The as-grown layers were annealed under different conditions to optimize the thermoelectric parameters. The obtained layers were investigated in their as-grown and annealed states using x-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive x-ray (EDX) spectroscopy, transmission electron microscopy (TEM), and electrical measurements. A lower limit of the elemental layer thickness was found to have c-orientation. Pure nanoalloyed Sb₂Te₃ layers were p-type as expected; however, it was impossible to synthesize p-type Bi₂Te₃ layers. Hence the Bi₂Te₃-Sb₂Te₃ superlattices consisting of alternating n- and p-type layers showed poor thermoelectric properties.     

Effects of Cooling Rate on Thermoelectric Properties of <Emphasis Type="Italic">n</Emphasis>-Type Bi<Subscript>2</Subscript>(Se<Subscript>0.4</Subscript>Te<Subscript>0.6</Subscript>)<Subscript>3</Subscript> Compounds

A series of Bi₂(Se_0.4Te_0.6)₃ compounds were synthesized by a rapid route of melt spinning (MS) combined with a subsequent spark plasma sintering (SPS) process. Measurements of the Seebeck coefficient, electrical conductivity, and thermal conductivity were performed over the temperature range from 300 K to 520 K. The measurement results showed that the cooling rate of melt spinning had a significant impact on the transport properties of electrons and phonons, effectively enhancing the thermoelectric properties of the compounds. The maximum ZT value reached 0.93 at 460 K for the sample prepared with the highest cooling rate, and infrared spectrum measurement results showed that the compound with lower tellurium content, Bi₂(Se_0.4Te_0.6)₃, possesses a larger optical forbidden gap (E _g) compared with the traditional n-type zone-melted material with formula Bi₂(Se_0.07Te_0.93)₃. Our work provides a new approach to develop low-tellurium-bearing Bi₂Te₃-based compounds with good thermoelectric performance.