High-frequency characteristics of AlGaAs/GaAs heterojunction bipolar transistors

The fabrication and high-frequency performance of MBE-grown AlGaAs/GaAs heterojunction bipolar transistors (HBT's) is described. The achieved gain-bandwidth product fTis 25 GHz for a collector current density Jcof 1 × 10⁴A/cm²and a collector-emitter voltage VCEof 3 V.fTcontinues to increase with the collector current in the high current density region over 1 × 10⁴A/cm²with no emitter crowding effect nor Kirk effect. The limitation on fTin fabricated devices is found to be caused mainly by the emitter series resistance.     

High-frequency output characteristics of AlGaAs/GaAs heterojunction bipolar transistors

A model has been developed which generates the high-frequency i/sub c/-v/sub ce/ output characteristics of bipolar transistors from computed cutoff frequency against current density data. The presented results, which can be used directly for large-signal modelling are the first report of high-frequency output characteristics of bipolar transistors.<>     

A comparison of low-frequency noise characteristics and noise sources in NPN and PNP InP-based heterojunction bipolar transistors

Low-frequency noise characteristics of NPN and PNP InP-based heterojunction bipolar transistors (HBTs) were investigated. NPN HBTs showed a lower base noise current level (3.85 /spl times/ 10/sup -17/ A/sup 2//Hz) than PNP HBTs (3.10 /spl times/ 10/sup -16/ A/sup 2//Hz), but higher collector noise current level (7.16 /spl times/ 10/sup -16/ A/sup 2//Hz) than PNP HBTs (1.48 /spl times/ 10/sup -16/ A/sup 2//Hz) at 10 Hz under I/sub C/=1 mA, V/sub C/=1 V. The NPN devices showed a weak dependence I/sub C//sup 0.77/ of the collector noise current, and a dependence I/sub B//sup 1.18/ of the base noise current, while the PNP devices showed dependences I/sub C//sup 1.92/ and I/sub B//sup 1.54/, respectively. The dominant noise sources and relative intrinsic noise strength were found in both NPN and PNP InP-based HBTs by comparing the noise spectral density with and without the emitter feedback resistor. Equivalent circuit models were employed and intrinsic noise sources were extracted. The high base noise current of PNP HBTs could be attributed to the exposed emitter periphery and higher electron surface recombination velocity in P-type InP materials, while the relatively high collector noise current of NPN HBTs may be due to the noise source originating from generation-recombination process in the bulk material between the emitter and the collector.     

Reliability of AlInAs/GaInAs heterojunction bipolar transistors

The reliability of high-performance AlInAs/GaInAs heterojunction bipolar transistors (HBTs) grown by molecular beam epitaxy (MBE) is discussed. Devices with a base Be doping level of 5×10¹⁹ cm^-3 and a base thickness of approximately 50 nm displayed no sign of Be diffusion under applied bias. Excellent stability in DC current gain, device turn-on voltage, and base-emitter junction characteristics was observed. Accelerated life-test experiments were performed under an applied constant collector current density of 7×10⁴ A/cm² at ambient temperatures of 193, 208, and 328°C. Junction temperature and device thermal resistance were determined experimentally. Degradation of the base-collector junction was used as failure criterion to project a mean time to failure in excess of 10⁷ h at 125°C junction temperature with an associated activation energy of 1.92 eV     

Numerical simulation of GaAs/GaAlAs heterojunction bipolar transistors

A numerical analysis program for the 1-dimensional simulation of GaAs/GaAlAs heterojunction bipolar transistors is described. Calculations for a representative transistor structure indicate that a cutoff frequency, ft, of 100 GHz is obtainable. To attain such a high value, the transistor design incorporated a graded-bandgap base region and relatively high emitter doping (5 × 10¹⁷cm^-3), and the device was operated at high current density (5 × 10⁴A/cm²). Transient electron velocity overshoot effects were also included.     

Fabrication and characterization of AlGaAs/GaAs heterojunction bipolar transistors

The fabrication and characterization of MBE-grown AlGaAs/GaAs heterojunction bipolar transistors (HBT's) are described, A Be redistribution profile in the HBT epi-layer at the emitter-base heterojunction interface is investigated using secondary ion mass spectrometry, A relatively high substrate temperature of 650°C during growth can be employed by introducing a 100-Å undoped spacer layer between the emitter and base layer. A simple wafer characterization method using phototransistors is demonstrated for accurately predicting current gain in a three-terminal device. A dc current gain of up to 230 is obtained for the fabricated HBT with a heavy base doping of 1 × 10¹⁹/cm³. A gain-bandwidth product fTof 25 GHz is achieved with a 4.5-µm-width emitter HBT.     

High-frequency characteristics of inverted-mode heterojunction bipolar transistors

It is shown that in emitter-down heterojunction bipolar transistors (HBT's), parasitics can be reduced sufficiently that intrinsic transit-time delays become the dominant limitations to high-frequency performance. In this situation it is found that the dependence of the unilateral gain on frequency can be significantly different from the simple 6-dB/octave decrease usually assumed. It is found that the device exhibits negative output conductance over certain bands of frequencies, and that when this occurs a series of resonances are observed in the gain versus frequency characteristics. Explanations of this behavior are given in terms of the phase delay of the common-base current gain. The generality and relevance of these observations to other types of transistors, and the utilization of the negative output conductance to enhance high-frequency operation are also discussed.     

High-speed, low-noise InGaP/GaAs heterojunction bipolar transistors

We have demonstrated self-aligned InGaP/GaAs heterojunction bipolar transistors (HBT's) with excellent dc, microwave, and noise performance. A 3×10 μm² emitter finger device achieved a cutoff frequency of f_T=66 GHz and a maximum frequency of oscillation of f_max=109 GHz. A minimum noise figure of 1.12 dB and an associated gain of 11 dB were measured at 4 GHz. These results are the highest combined f_T+f_max and the lowest noise figure reported for an InGaP/GaAs HBT and are attributed to material quality and the use of self-aligned base contacts. These data clearly demonstrate the viability of InGaP/GaAs HBT's for high-speed, low-noise circuit applications     

An approach to determine small-signal model parameters for InP-based heterojunction bipolar transistors

A new method for the extraction of the small-signal model parameters of InP-based heterojunction bipolar transistors (HBT) is proposed. The approach is based on the combination of the analytical and optimization technology. The initial values of the parasitic pad capacitances are extracted by using a set of closed-form expressions derived from cutoff mode S-parameters without any test structure, and the intrinsic elements determined by using the analytical method are described as functions of the parasitic elements. An advanced design system is then used to optimize only the parasitic parameters with very small dispersion of initial values. Good agreement is obtained between simulated and measured results for an InP HBT with 5/spl times/5 /spl mu/m/sup 2/ emitter area over a wide range of bias points up to 40 GHz.     

Integration of GalnP/GaAs heterojunction bipolar transistors andhigh electron mobility transistors

Integration of carbon-doped GaInP/GaAs heterojunction bipolar transistors (HBTs) and high electron mobility transistors (HEMTs) is demonstrated by growing an HBT on the top of a HEMT. A current gain of 60, a cutoff frequency of 59 GHz and a maximum oscillation frequency of 68 GHz were obtained for a 5×15 μm² self-aligned HBT. The HEMT, with a gate length of 1.5 μm has a transconductance of 210 mS/mm, a cutoff frequency of 9 GHz and a maximum oscillation frequency of 22 GHz. It is shown that the GaInP/GaAs HBT on the HEMT is a simple Bi-FET technology suitable for microwave and mixed signal applications     

Reliability of III–V based heterojunction bipolar transistors

This paper reviews the reliability of III-V based heterojunction bipolar transistors (HBTs). These devices have many potential advantages over other solid-state microwave devices. However, because of the tradeoff between performance and reliability, they are not being used to any great extent in power microwave applications. In the type of III-V HBT device most fully developed, the AlGaAs/GaAs HBT, leakage currents play a major role in the dominant mode of degradation. Because low-frequency noise is related to these leakage currents it has been used extensively in the analysis of the performance and reliability limitations of these devices. The reliability of other types of III-V HBT devices, such as InGaP/GaAs and InP based devices, is also discussed.     

Reliability of microwave SiGe/Si heterojunction bipolar transistors

The degradation behavior of NPN Si/SiGe/Si heterojunction bipolar transistors, grown by solid-source molecular beam epitaxy (MBE), has been studied by accelerated lifetime testing at different ambient temperatures. The degradations of the dc current gain and the microwave performance of the devices are explained in terms of recombination enhanced impurity diffusion (REID) of boron atoms from the base region and the subsequent formation of parasitic energy barriers at the base-emitter and base-collector junctions     

High-frequency performance of lattice-strained heterojunction GaInAs/GaAs bipolar transistors

The performance of bipolar devices and circuits in the novel lattice-strained GaInAs/GaAs materials system show an improving trend with increased In composition in the base. An fT of 8 GHz has been measured using an 8 ?m emitter stripe width and 8% In. A small-signal model is presented.     

Monte Carlo simulation of AlGaAs/GaAs heterojunction bipolar transistors

A first demonstration of one-dimensional Monte Carlo simulations of AlGaAs/GaAs heterojunction bipolar transistors is reported. The electron motion is solved by a particle model, while the hole motion is solved by a conventional hydrodynamic model. It is shown that the compositional grading of AlxGa1-xAs in the base region is effective to cause the ballistic acceleration of electrons in the base region, resulting in a high collector current density of above 1 mA/µm². The current-gain cutoff frequency fT reaches 150 GHz if the size of a transistor is properly designed. Also shown is the relation between the device performances and the electron dynamics investigated.     

Comparison of GaInP/GaAs heterostructure-emitter bipolartransistors and heterojunction bipolar transistors

Carbon-doped GaInP/GaAs heterojunction bipolar transistors (HBT's) and heterostructure-emitter bipolar transistors (HEBT's) grown by MOCVD were fabricated. Experimental comparison of HBT's and HEBT's has been made based on the dc and the RF performance. HBT's have higher current gains than those of HEBT's in the high current regime, while HEBT's offer a smaller offset voltage and better uniformity in dc characteristics across the wafer. The current gain and cutoff frequency of the DEBT with a 150 Å emitter set-back layer are comparable to those of HBT's. DC (differential) current gains of 600 (900) and 560 (900) were obtained at a collector current density of 2.5×10⁴ A/cm² for the HBT and HEBT, respectively. The cutoff frequencies are 37 and 31 GHz for the HBT and HEBT, respectively. It is shown that there is negligible contribution of the diffusion capacitance to the emitter capacitance in HEBT's with a thin emitter set-back layer but not with a thick emitter set-back layer. The behavior of HEBT's both in dc and RF characteristics is similar to that of HBT's     

Planar AlGaAs/GaAs heterojunction bipolar transistors fabricatedusing selective W-CVD

The authors describe a planar process for the AlGaAs/GaAs HBTs in which collector vias are buried selectively, even to the base layers, with chemical vapor deposited tungsten (CVD-W) films. By using WF₆ /SiH₄ chemistry, W could be deposited on Pt films, which were overlapped 50 nm thick on the AuGe-based collector electrodes, without depositing W on the surrounding SiO₂ layers. Current gains of planar HBTs with 3.5-μm×3.5-μm emitters were up to 150, for a collector current density of about 2.5×10⁴ A/cm²     

GaAs/AlGaAs heterojunction bipolar transistors for integrated circuit applications

Molecular-beam epitaxy (MBE) and ion implantation were used to fabricate GaAs/AlGaAs heterojunction bipolar transistors with buried wide bandgap emitters. Inverted-mode current gains of ∼ 100 were obtained, demonstrating the feasibility of this technology for I²L types of digital integrated circuits.     

Self-aligned InGaP/GaAs heterojunction bipolar transistors formicrowave power application

As an alternative to AlGaAs/GaAs heterojunction bipolar transistors (HBTs) for microwave applications, InGaP/GaAs HBTs with carbon-doped base layers grown by metal organic molecular beam epitaxy (MOMBE) with excellent DC, RF, and microwave performance are demonstrated. As previously reported, with a 700-Å-thick base layer (135-Ω/sq sheet resistance), a DC current gain of 25, and cutoff frequency and maximum frequency of oscillation above 70 GHz were measured for a 2-μm×5-μm emitter area device. A device with 12 cells, each consisting of a 2-μm×15-μm emitter area device for a total emitter area of 360 μm², was power tested at 4 GHz under continuous-wave (CW) bias condition. The device delivered 0.6-W output power with 13-dB linear gain and a power-added efficiency of 50%     

Improving collector-current uniformity in emitter-gradedAlGaAs/GaAs heterojunction bipolar transistors

To investigate the effect of a graded layer on collector-current uniformity, two types of HBTs were fabricated by metalorganic chemical vapor deposition (MOCVD). One type had a bandgap graded layer at the emitter-based interface to eliminate the conduction-band spike. The other type was a conventional HBT (heterojunction bipolar transistor) with an abrupt heterojunction fluctuated due to the fluctuation of the barrier energy from the emitter to the base. The bandgap-graded layer drastically suppressed the fluctuation of the collector current. the standard deviation of the threshold voltage was improved from 3.03 to 0.42 V by adopting bandgap grading at the emitter-based interface     

An emitter guard-ring structure for GaAs high-gain heterojunction bipolar transistors

An emitter guard-ring structure is adopted for GaAs/AlGaAs heterojunction bipolar transistors (HBT's). The guard ring is added around the central emitter and has nearly the same dc bias as the base, so that the carrier injection as well as the surface recombination at the emitter periphery is blocked. As a result, the current gain at low operating currents is improved remarkably. It remains almost constant at 600 as the collector current is decreased from 20 mA down to 5 µA. This is the best result to date for a GaAs HBT at low currents. This technique also makes it possible to investigate the interface quality without interference from surface effects.