Synthetic spinels of the system MgO-Cr<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>

Synthetic spinels of the system MgO-Cr₂O₃-Al₂O₃-Fe₂O₃ are considered and the desirability of organizing their production for the refractory industry is demonstrated. Translated from Novye Ogneupory, No. 6, pp. 32–35, June 2008.     

Separation characteristics of tetrapropylammoniumbromide templating silica/alumina composite membrane in CO<Subscript>2</Subscript>/N<Subscript>2</Subscript>, CO<Subscript>2</Subscript>/H<Subscript>2</Subscript> and CH<Subscript>4</Subscript>/H<Subscript>2</Subscript> systems

Nanoporous silica membrane without any pinholes and cracks was synthesized by organic templating method. The tetrapropylammoniumbromide (TPABr)-templating silica sols were coated on tubular alumina composite support ( γ-Al₂O₃/ α-Al₂O₃ composite) by dip coating and then heat-treated at 550 °C. By using the prepared TPABr templating silica/alumina composite membrane, adsorption and membrane transport experiments were performed on the CO₂/N₂, CO₂/H₂ and CH₄/H₂ systems. Adsorption and permeation by using single gas and binary mixtures were measured in order to examine the transport mechanism in the membrane. In the single gas systems, adsorption characteristics on the α-Al₂O₃ support and nanoporous unsupport (TPABr templating SiO₂/ γ-Al₂O₃ composite layer without α-Al₂O₃ support) were investigated at 20–40 °C conditions and 0.0–1.0 atm pressure range. The experimental adsorption equilibrium was well fitted with Langmuir or/and Langmuir-Freundlich isotherm models. The α-Al₂O₃ support had a little adsorption capacity compared to the unsupport which had relatively larger adsorption capacity for CO₂ and CH₄. While the adsorption rates in the unsupport showed in the order of H₂> CO₂> N₂> CH₄ at low pressure range, the permeate flux in the membrane was in the order of H₂≫N₂> CH₄> CO₂. Separation properties of the unsupport could be confirmed by the separation experiments of adsorbable/non-adsorbable mixed gases, such as CO₂/H₂ and CH₄/H₂ systems. Although light and non-adsorbable molecules, such as H₂, showed the highest permeation in the single gas permeate experiments, heavier and strongly adsorbable molecules, such as CO₂ and CH₄, showed a higher separation factor (CO₂/H₂=5-7, CH₄/H₂=4-9). These results might be caused by the surface diffusion or/and blocking effects of adsorbed molecules in the unsupport. And these results could be explained by surface diffusion. This paper is dedicated to Professor Hyun-Ku Rhee on the occasion of his retirement from Seoul National University.     

Low-temperature anti-icing reagents in the Ca(NO<Subscript>3</Subscript>)<Subscript>2</Subscript>-Mg(NO<Subscript>3</Subscript>)<Subscript>2</Subscript>-CO(NH<Subscript>2</Subscript>)<Subscript>2</Subscript>-H<Subscript>2</Subscript>O system and their properties

The polytherms of ice melting in sections of the Ca(NO₃)₂-Mg(NO₃)₂-CO(NH₂)₂-H₂O system with different component ratios were studied in the temperature interval from 0 to −40°C. A series of nitrate and nitrate-carbonate reagents that are promising for the creation of anti-acing reagents were found, which form eutectics with ice at temperatures from −25 to −39°C. Their properties, viz., melting properties with respect to ice and corrosiveness on metals and alloys, were determined. An effective corrosion inhibitor was selected.     

Li<Subscript>2</Subscript>Cu<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> + SiO<Subscript>2</Subscript>/Ti compositions for the catalytic afterburning of diesel soot

Two methods were used to obtain a catalytically active oxide coating on the surface of titanium for the catalytic afterburning of diesel soot: plasma electrochemical formation of an oxide film on the surface of titanium and extraction pyrolytic deposition of the Li₂Cu₂(MoO₄)₃ compound. The Li₂Cu₂(MoO₄)₃/TiO₂ + SiO₂/Ti compositions synthesized by the single-step extraction pyrolytic treatment of the oxidized surface of titanium ensured a high burning rate of soot of ∼300°C. The subsequent deposition of Li₂Cu₂(MoO₄)₃ lowers the activity of the catalyst, due probably to the growth of molybdate phase crystallites and the filling of open oxide film pores. Double lithium-copper molybdate is able to reduce appreciably the concentration of CO in the oxidation products of soot. The advantages of these methods are the possibility of forming high-cohesion durable coatings on surfaces of any complexity, the simplicity of their implementation, and high productivity and low cost. The obtained results can be recommended for use in developing methods for creating composite coatings on catalytic soot filters.     

Crystal structure of new compound (Rb,K)<Subscript>2</Subscript>Cu<Subscript>3</Subscript>(P<Subscript>2</Subscript>O<Subscript>7</Subscript>)<Subscript>2</Subscript>

A new compound of (Rb,K)₂Cu₃(P₂O₇)₂ is obtained by high-temperature reactions from a mixture of RbNO₃, KNO₃, Cu(NO₃)₂, and (NH₄)₄P₂O₇. The crystal structure was solved by direct methods and refined to R ₁ = 0.056 for 5022 independent reflections. The compound belongs to a rhombic crystal system, P2₁2₁2₁, Z = 8, a = 9.9410(7) Å, b = 13.4754(6) Å, c = 18.6353 (3) Å, and R = 0.056. The basis of the structure is a complex copper-phosphate skeleton of the composition of [Cu₃(P₂O₇)₂]^2–, which can be regarded as consisting of two types of heteropolyhedral layers parallel to the (001) plane. The layers are alternated with each other, forming a frame, in the cavities of which the positions of alkali cations are located, statistically populated with K⁺ and Rb⁺ ions. Based on the refined populations of the positions of alkali cations, an exact chemical formula of the compound can be written as Rb_1.28K_0.72Cu₃(P₂O₇)₂. The compound is the most complex among those known to this day of the composition of A₂ ^IB₃ ^II(P₂O₇)₂ (A = Li, Na, K, Rb, or Cs; B = Ni, Cu, or Zn).     

Optical Properties of CeO<Subscript>2</Subscript> Doped SiO<Subscript>2</Subscript>-Na<Subscript>2</Subscript>O-CaO-P<Subscript>2</Subscript>O<Subscript>5</Subscript> Glasses

Cerium oxide is one of the most important rare earth elements that is introduced into glass compositions due to its great effects on the optical properties. CeO₂ was introduced in Hench’s patented SiO₂-Na₂O-CaO-P₂O₅ glasses with different concentrations in order to study its effect on the optical behavior of this glass including optical band gap, transmittance, reflectance and refractive index and to give a complete view for the optical properties on cerium oxide-doped silicate glasses.     

Crystallization Behavior of Amorphous Zr<Subscript>55</Subscript>Cu<Subscript>20</Subscript>Ni<Subscript>10</Subscript>Al<Subscript>10</Subscript>Ti<Subscript>5</Subscript> Alloy

In the present study, the crystallization behavior and thermal stability of amorphous Zr₅₅Cu₂₀Ni₁₀Al₁₀Ti₅ alloy, obtained by melt-spinning, have been investigated using X-ray diffraction (XRD), differential thermal analysis (DTA) and transmission electron microscopy (TEM). The activation energy for crystallization has been evaluated by the Kissinger method, and it has been found that E _x obtained from the crystallization onset temperature (T _x) is lower than E _p determined by the crystallization peak temperature (T _P). During the continuous annealing process, ZrO and h-Al₃Zr₅ phases firstly precipitate from the amorphous matrix, then Zr₂Ni_0.66O_0.33 phase forms continuously and its relative content increases with increasing annealing temperature. However, no crystalline phases have been observed during the isothermal annealing process at 733 K (below T _x) for 90 min. The atomic clusters can keep the stability state through adjusting the short-range ordering.     

Electrical conductivity and structure of glasses in the Na<Subscript>2</Subscript>O-Na<Subscript>2</Subscript>S-P<Subscript>2</Subscript>O<Subscript>5</Subscript> and Na<Subscript>2</Subscript>S-P<Subscript>2</Subscript>S<Subscript>5</Subscript> systems

The glasses, in which oxygen was partially replaced with sulfur, have been synthesized in the Na₂O-P₂O₅-Na₂S system. The chemical and chromatographic analyses of the glasses synthesized have been performed. The temperature-concentration dependences of electrical conductivity of the glasses have been studied over a wide temperature range; the glass transition temperatures and the nature of charge carriers have been determined. The IR spectra and Raman spectra have been recorded at room temperature; the density and microhardness of the glasses and ultrasound velocity have been measured. A comparison of the electrical conductivities of the investigated glasses with those of the earlier studied glasses in the Na₂O-P₂O₅ system has shown their fair coincidence. The introduction of sodium sulfide into the Na₂O-P₂O₅ system is accompanied by an approximately threefold increase in electrical conductivity, although the concentrations of charge carriers (sodium ions) in the glasses amount to ∼17 and ∼26 mmol/cm³, respectively. The rise in electrical conductivity has been assumed to be caused by the increase in the degree of dissociation of polar structural chemical units including sulfide ions and by the higher mobility of sodium ions in the oxygen-free matrix.     

Thermal Behavior of Howlite,Ca<Subscript>2</Subscript>B<Subscript>5</Subscript>SiO<Subscript>9</Subscript>(OH)<Subscript>5</Subscript>

The thermal behavior of natural borosilicate howlite, Ca₂B₅SiO₉(OH)₅, is studied by the methods of high-temperature X-ray diffraction and differential thermal analysis in the temperature range of 30–1100°C. The thermal expansion is anisotropic (α_max/α_min = 3.6); the degree of anisotropy increases (α_max/α_min = 4.3) with a temperature increase up to 480°C (360–480°C).     

Phase Equilibria in the Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>-SrAl<Subscript>2</Subscript>O<Subscript>4</Subscript> System

The phase equilibria are investigated and the phase diagram is constructed for the Gd₂O₃-SrAl₂O₄ pseudobinary join of the Gd₂O₃-SrO-Al₂O₃ ternary oxide system. One ternary compound, namely, Gd₂SrAl₂O₇, is revealed in the Gd₂O₃-SrAl₂O₄ join. It is found that this compound undergoes congruent melting.     

Investigation of a new lead-free Bi<Subscript>0.5</Subscript>(Na<Subscript>0.40</Subscript>K<Subscript>0.10</Subscript>)TiO<Subscript>3</Subscript>-(Ba<Subscript>0.7</Subscript>Sr<Subscript>0.3</Subscript>)TiO<Subscript>3</Subscript> piezoelectric ceramic

Lead-free piezoelectric compositions of the (1-x)Bi_0.5(Na_0.40K_0.10)TiO₃-x(Ba_0.7Sr_0.3)TiO₃ system (when x = 0, 0.05, 0.10, 0.15, and 0.20) were fabricated using a solid-state mixed oxide method and sintered between 1,050°C and 1,175°C for 2 h. The effect of (Ba_0.7Sr_0.3)TiO₃ [BST] content on phase, microstructure, and electrical properties was investigated. The optimum sintering temperature was 1,125°C at which all compositions had densities of at least 98% of their theoretical values. X-ray diffraction patterns that showed tetragonality were increased with the increasing BST. Scanning electron micrographs showed a slight reduction of grain size when BST was added. The addition of BST was also found to improve the dielectric and piezoelectric properties of the BNKT ceramic. A large room-temperature dielectric constant, ε _r (1,609), and piezoelectric coefficient, d ₃₃ (214 pC/N), were obtained at an optimal composition of x = 0.10.     

Phase equilibria in the Ho<Subscript>2</Subscript>O<Subscript>3</Subscript>-SrAl<Subscript>2</Subscript>O<Subscript>4</Subscript> system

The phase formation is investigated and the phase diagram of the Ho₂O₃-SrAl₂O₄ system is constructed. A ternary compound, namely, Ho₂SrAl₂O₇, is revealed. It is established that this compound undergoes incongruent melting.     

Thermal behavior of reedmergnerite NaBSi<Subscript>3</Subscript>O<Subscript>8</Subscript> and searlesite NaBSi<Subscript>2</Subscript>O<Subscript>5</Subscript>(OH)<Subscript>2</Subscript>

The results of studying the thermal behavior of natural boron albite–reedmergnerite NaBSi₃O₈ and aqueous boricilicate–searlesite NaBSi₂O₅(OH)₂ obtained by the method of hydrothermal synthesis are presented. In the investigated temperature range, reedmergnerite (30–780°C) does not undergo phase transformations. Thermal expansion is sharply anisotropic, which is a characteristic feature of the expansion of feldspars. Aqueous borosilicate searlesite (25–750°C) is amorphized above 400°C as a result of dehydration and cristobalite crystallizes from the amorphous phase. The expansion of searlesite is relatively isotropic.     

Unexpected Support Effect in Hydrotreating: Evidence of a Metallic Character for ReS<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and ReS<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> Catalysts

Abstract  

Rhenium sulfide based catalysts were prepared by the incipient wetness impregnation method over alumina and silica supports and evaluated for 4,6-dimethyldibenzothiophene hydrodesulfurization in a high-pressure stirred-tank reactor. The catalyst prepared over silica was about six times more active for hydrodesulfurization than the corresponding catalyst prepared over alumina and a NiMo/Al₂O₃ industrial reference catalyst. This surprising and positive SiO₂ support effect was explained by a metallic character of the supported sulfide, which was demonstrated using a kinetic approach of competitive hydrogenations and by XPS characterization.     

Synthesis and crystal structure of the low-temperature modification of Li<Subscript>12</Subscript>Zn<Subscript>4</Subscript>(P<Subscript>2</Subscript>O<Subscript>7</Subscript>)<Subscript>5</Subscript>

The crystal structure of a low-temperature modification of the Li₁₂Zn₄(P₂O₇)₅ compound has been determined by full-profile analysis from the X-ray powder diffraction data. The compound crystallizes in the monoclinic crystal system (a = 5.130(1) Å, b = 13.454(1) Å, c = 8.205(1) Å, β = 90.36(1)°, space group P2₁/n, Z = 4) and has a framework structure in which the zinc and lithium atoms statistically occupy equivalent positions.     

Structure and properties of glasses in the MgSO<Subscript>4</Subscript>-Na<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript>-KPO<Subscript>3</Subscript> system

A glass formation region has been established in the MgSO₄-Na₂B₄O₇-KPO₃ system. This region is located in the borate-phosphate part of the concentration triangle and occupies ∼40% of the triangle area. Based on the spectral data obtained (nuclear magnetic resonance, IR and Raman spectroscopy), a model is proposed in terms of which the physicochemical properties (such as the linear thermal expansion coefficient, the softening temperature, and the glass transition temperature) of the samples are discussed.