Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.     

Mean field modelling of NOx storage on Pt/BaO/Al2O3

A mean field model, for storage and desorption of NO_x in a Pt/BaO/Al₂O₃ catalyst is developed using data from flow reactor experiments. This relatively complex system is divided into five smaller sub-systems and the model is divided into the following steps: (i) NO oxidation on Pt/Al₂O₃; (ii) NO oxidation on Pt/BaO/Al₂O₃; (iii) NO_x storage on BaO/Al₂O₃; (iv) NO_x storage on Pt/BaO/Al₂O₃ with thermal regeneration and (v) NO_x storage on Pt/BaO/Al₂O₃ with regeneration using C₃H₆. In this paper, we focus on the last sub-system. The kinetic model for NO_x storage on Pt/BaO/Al₂O₃ was constructed with kinetic parameters obtained from the NO oxidation model together with a NO_x storage model on BaO/Al₂O₃. This model was not sufficient to describe the NO_x storage experiments for the Pt/BaO/Al₂O₃, because the NO_x desorption in TPD experiments was larger for Pt/BaO/Al₂O₃, compared to BaO/Al₂O₃. The model was therefore modified by adding a reversible spill-over step. Further, the model was validated with additional experiments, which showed that NO significantly promoted desorption of NO_x from Pt/BaO/Al₂O₃. To this NO_x storage model, additional steps were added to describe the reduction by hydrocarbon in experiments with NO₂ and C₃H₆. The main reactions for continuous reduction of NO_x occurs on Pt by reactions between hydrocarbon species and NO in the model. The model is also able to describe the reduction phase, the storage and NO breakthrough peaks, observed in experiments.     

Thermoelectric characterization of NaxMx/2Ti1−x/2O2 (M=Co, Ni and Fe) polycrystalline materials

Layered -titanate materials, Na_xM_x/2Ti_1−x/2O₂ (M=Co, Ni and Fe, x=0.2–0.4), were synthesized by flux reactions, and electrical properties of polycrystalline products were measured at 300–800 °C. After sintering at 1250 °C in Ar, all products show n-type thermoelectric behavior. The values of both d.c. conductivity and Seebeck coefficient of polycrystalline Na_0.4Ni_0.2Ti_0.8O₂ were ca. 7×10³ S/m and ca. −193 μV/K around 700 °C, respectively. The measured thermal conductivity of layered -titanate materials has lower value than conductive oxide materials. It was ca. 1.5 Wm⁻¹ K⁻¹ at 800 °C. The estimated thermoelectric figure-of-merit, Z, of Na_0.4Ni_0.2Ti_0.8O₂ and Na_0.4Co_0.2Ti_0.8O₂ was about 1.9×10⁻⁴ and 1.2×10⁻⁴ K⁻¹ around 700 °C, respectively.     

High temperature catalytic combustion of methane and propane over hexaaluminate catalysts: NOx emission characteristics

Several hexaaluminate-related materials were prepared via hydrolysis of alkoxide and powder mixing method for high temperature combustion of CH₄ and C₃H₈, in order to investigate the effect of the concentration of the fuels, O₂ and H₂O on NO_x emission and combustion characteristics. Among the hexaaluminate catalysts, Sr_0.8La_0.2MnAl₁₁O₁₉₋ prepared by the alkoxide method exhibited the highest activity for methane combustion and low NO_x emission capability. NO_x emission at 1500 °C was increased linearly with O₂ concentration, whereas water vapor addition decreased NO_x emission in CH₄ combustion over the Sr_0.8La_0.2MnAl₁₁O₁₉₋ catalyst. In the catalytic combustion of C₃H₈ over the Sr_0.8La_0.2MnAl₁₁O₁₉₋ catalyst, the amount of NO_x emitted was raised in the temperature range between 1000 and 1500 °C when the C₃H₈ concentration increased from 1 to 2 vol.%. It was found that NO_x emission in this temperature range was reduced effectively by adding water vapor.     

Quantification of the in situ DRIFT spectra of Pt/K/γ-A12O3 NOx adsorber catalysts

A method to quantify DRIFT spectral features associated with the in situ adsorption of gases on a NO_x adsorber catalyst, Pt/K/Al₂O₃, is described. To implement this method, the multicomponent catalyst is analysed with DRIFT and chemisorption to determine that under operating conditions the surface comprised a Pt phase, a pure γ-Al₂O₃ phase with associated hydroxyl groups at the surface, and an alkalized-Al₂O₃ phase where the surface –OH groups are replaced by –OK groups. Both DRIFTS and chemisorption experiments show that 93–97% of the potassium exists in this form. The phases have a fractional surface area of 1.1% for the 1.7 nm-sized Pt, 34% for pure Al₂O₃ and 65% for the alkalized-Al₂O₃. NO₂ and CO₂ chemisorption at 250 °C is implemented to determine the saturation uptake value, which is observed with DRIFTS at 250 °C. Pt/Al₂O₃ adsorbs 0.087 μmol CO₂/m²and 2.0 μmol NO₂/m², and Pt/K/Al₂O₃ adsorbs 2.0 μmol CO₂/m²and 6.4 μmol NO₂/m². This method can be implemented to quantitatively monitor the formation of carboxylates and nitrates on Pt/K/Al₂O₃ during both lean and rich periods of the NO_x adsorber catalyst cycle.     

Sorption kinetics of ammonia and ammonium ions on gel and macroporous sulphonic acid cation exchangers

Diffusion of ammonia and ammonium ions in sulphonic acid cation exchangers (gel Purolite SGC 100 × 10 MBH and macroporous Purolite C 160 MBH) from the solutions, representing the composition of “caustic condensate” (waste of nitrogen fertilizers production) is affected by pH of initial solution and structure of the matrix of cation exchanger. In gel matrix the effective intraparticle diffusivity (D_ef) depends greatly on the solution pH because of shrinkage in alkaline and swelling in acidic medium: on decreasing the initial concentration of ammonia from 0.214 to 0.003 and increasing that of ammonium nitrate from 0 to 0.214 mol l⁻¹ instead, the effect of ion exchange leads to a decrease in pH, resulting in swelling and increase in D_ef from 0.1 to 0.34 × 10⁻¹⁰ for gel Purolite SGC 100 × 10 MBH and variation of 0.18–0.11 × 10⁻¹⁰ m² s⁻¹ for macroporous Purolite C 160 MBH (resistant to shrinkage and swelling).

In Purolite C 160 MBH both macropore diffusivity (0.07–0.29 × 10⁻¹⁰ m² s⁻¹) and gel (solid phase) diffusivity (0.06–0.19 × 10⁻¹⁰ m² s⁻¹) are higher than micropore diffusivity (0.28–0.56 × 10⁻¹⁸ m² s⁻¹).

With respect to the effective intraparticle diffusivity, resistance to nitric acid, used for the regeneration, and high concentration of ammonium nitrate in eluate (up to 110 g l⁻¹), Purolite C 160 MBH has been installed for the conversion of ammonia and ammonium ions to ammonium nitrate reusable in the fertilizers production. This allows minimizing the economic loss and preventing the environmental contamination.     

Catalytic behavior of La–Sr–Ce–Fe–O mixed oxidic/perovskitic systems for the NO+CO and NO+CH4+O2 (lean-NOx) reactions

Mixed oxides of the general formula La_0.5Sr_xCe_yFeO_z were prepared by using the nitrate method and characterized by XRD and Mössbauer techniques. The crystal phases detected were perovskites LaFeO₃ and SrFeO_3−x and oxides -Fe₂O₃ and CeO₂ depending on x and y values. The low surface area ceramic materials have been tested for the NO+CO and NO+CH₄+O₂ (“lean-NO_x”) reactions in the temperature range 250–550°C. A noticeable enhancement in NO conversion was achieved by the substitution of La³⁺ cation at A-site with divalent Sr⁺² and tetravalent Ce⁺⁴ cations. Comparison of the activity of the present and other perovskite-type materials has pointed out that the ability of the La_0.5Sr_xCe_yFeO_z materials to reduce NO by CO or by CH₄ under “lean-NO_x” conditions is very satisfying. In particular, for the NO+CO reaction estimation of turnover frequencies (TOFs, s⁻¹) at 300°C (based on NO chemisorption) revealed values comparable to Rh/-Al₂O₃ catalyst. This is an important result considering the current tendency for replacing the very active but expensive Rh and Pt metals. It was found that there is a direct correlation between the percentage of crystal phases containing iron in La_0.5Sr_xCe_yFeO_z solids and their catalytic activity. O₂ TPD (temperature-programmed desorption) and NO TPD studies confirmed that the catalytic activity for both tested reactions is related to the defect positions in the lattice of the catalysts (e.g., oxygen vacancies, cationic defects). Additionally, a remarkable oscillatory behavior during O₂ TPD studies was observed for the La_0.5Sr_0.2Ce_0.3FeO_z and La_0.5Sr_0.5FeO_z solids.     

Combinatorial preparation and high-throughput catalytic tests of multi-component deNOx catalysts

A quaternary catalyst library of 56 samples comprising all combinations of four elements, viz. Ag, Co, Cu, In, with six equally spaced atomic fraction increments from 0 to 1 was prepared by impregnation of a proprietary mesoporous alumina support. Catalytic properties of the library were tested in the selective catalytic reduction (SCR) of NO_x by propane under lean conditions in the temperature range 400–500 °C. The catalytic data acquired by a parallel 64-channel microreactor system with automated time-of-flight mass spectrometric analysis have been evaluated regarding selectivity–compositional relationships, synergistic effects for NO_x conversion, and efficiency of propane utilization. Full conversion of NO_x is achieved over Ag–Co combinations at 450 °C with N₂ selectivities of more than 90% and reductant utilization of 20% in a feed of 1500 ppm NO, 1500 ppm propane and 5 vol.% O₂ (space velocity of 36,000 cm³ g_cat⁻¹ h⁻¹). For the single-component catalysts Ag/Al₂O₃, Co/Al₂O₃, Cu/Al₂O₃, and In/Al₂O₃, the state of the elements on the mesoporous alumina was characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). Cobalt forms a spinel-like cobalt aluminate phase whereas copper and indium are present as oxides with small sizes not detectable by XRD. Silver occurs in both metallic state and as Ag₂O, and forms Ag_n clusters of at least two different sizes, predominantly with diameters of about 30 nm. The conclusions are consistent with the reducibility of the single-component catalysts samples by H₂. Surface area measurements and pore size distributions revealed reasonable modifications of the textural properties. The main pore size of the alumina support is decreased from 7 to ca. 5 nm after loading of the active components.     

Mn/MFI catalyzed reduction of NOx with alkanes

Mn/MFI catalysts were prepared by different methods and probed as catalysts for the catalytic reduction of NO_x with CH₄ or iso-butane in a gas flow containing excess O₂. Mn/MFI with high manganese loading was obtained by solid state ion exchange (SSI). The intensity of an IR band at 957 cm⁻¹, which is due to the perturbation of zeolite lattice vibrations by Mn ions attached to cage walls is proportional to the Mn content of the catalysts. Conversely, the intensity of the 3610 cm⁻¹ band, assigned to Brønsted acid sites decreases linearly with the Mn loading. A catalyst obtained by exchanging Na/MFI with an aqueous solution of Mn acetate is found most active for NO_x reduction with methane. Transport by surface diffusion of Mn ions from MnI₂ to exchange positions in MFI is more efficient than their transport through the gas phase. High NO conversion over proton-free catalysts indicates that protons are not instrumental in NO_x reduction over Mn/MFI.     

Influence of operating parameters on photocatalytic degradation of phenol in UV/TiO2 process

The use of hydrogen peroxide (H₂O₂) for improved photocatalytic degradation of phenol in aqueous suspension of commercial TiO₂ powders (Degussa P-25) was investigated. Photodegradation was compared using direct photolysis (UV alone), H₂O₂/UV, TiO₂/UV, and H₂O₂/TiO₂/UV processes in a batch reactor with high-pressure mercury lamp irradiation. The effects of operating parameters such as catalyst dosage, light intensity, pH of the solution, the initial phenol, and H₂O₂ concentrations on photodegradation process were examined. It was shown that photodegradation using H₂O₂/TiO₂/UV process was much more effective than using either H₂O₂/UV or TiO₂/UV process. The effect of the initial phenol concentration on TOC removal was also studied, demonstrating that more than 8 h was required to completely mineralize phenol into water and carbon dioxide. For all the four oxidation processes studied, photodegradation followed the first-order kinetics. The apparent rate constants with 400-W UV ranged from 5.0 × 10⁻⁴ min⁻¹ by direct photolysis to 1.4 × 10⁻² min⁻¹ using H₂O₂/TiO₂/UV process. The role of H₂O₂ on such enhanced photodegradation of phenol in aqueous solution was finally discussed.     

The activity and characterization of sol–gel Sn/Al2O3 catalyst for selective catalytic reduction of NOx in the presence of oxygen

Catalytic performance of Sn/Al₂O₃ catalysts prepared by impregnation (IM) and sol–gel (SG) method for selective catalytic reduction of NO_x by propene under lean burn condition were investigated. The physical properties of catalyst were characterized by BET, XRD, XPS and TPD. The results showed that NO₂ had higher reactivity than NO to nitrogen, the maximum NO conversion was 82% on the 5% Sn/Al₂O₃ (SG) catalyst, and the maximum NO₂ conversion reached nearly 100% around 425 °C. Such a temperature of maximum NO conversion was in accordance with those of NO_x desorption accompanied with O₂ around 450 °C. The activity of NO reduction was enhanced remarkably by the presence of H₂O and SO₂ at low temperature, and the temperature window was also broadened in the presence of H₂O and SO₂, however the NO_x desorption and NO conversion decreased sharply on the 300 ppm SO₂ treated catalyst, the catalytic activity was inhibited by the presence of SO₂ due to formation of sulfate species (SO₄²⁻) on the catalysts. The presence of oxygen played an essential role in NO reduction, and the activity of the 5% Sn/Al₂O₃ (SG) was not decreased in the presence of large oxygen.     

On-stream modification of MFI zeolite membranes for enhancing hydrogen separation at high temperature

-Alumina-supported MFI zeolite membranes were modified by on-stream catalytic thermal cracking of methyldiethoxysilane (MDES) molecules inside the zeolitic channels during the separation of H₂/CO₂ gas mixture at 450 °C and atmospheric pressure. The MDES vapor was carried by the H₂/CO₂ feed gas and the effect of modification was monitored continuously through online analysis of the permeate stream. The modified membrane exhibited a significant increase in H₂ selectivity over CO₂ with a moderate decrease in H₂ permeance. At 450 °C, the modified MFI membrane obtained a H₂/CO₂ permselectivity of 17.5 with H₂ single gas permeance of 1.86 × 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ as compared to a permselectivity of 2.78 and permeance of 2.75 × 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ for the membrane before modification. The modified membrane also showed good performance and stability in separation of H₂/CO₂ gas mixture containing up to 28.4% water vapor at 450 °C and atmospheric pressure.     

Selective permeation and separation of steam from water–methanol–hydrogen gas mixtures through mordenite membrane

Separation properties of a mordenite membrane for water–methanol–hydrogen mixtures were studied in the temperature range from 423 to 523 K under pressurized conditions. The mordenite membrane was prepared on the outer surface of a porous alumina tubular support by a secondary-growth method. It was found that water was selectively permeated through the membrane. The separation factor of water/hydrogen and water/methanol were 49–156 and 73–101, respectively. Even when only hydrogen was fed at 0.5 MPa, its permeance was as low as 10⁻⁹ mol m⁻² s⁻¹ Pa⁻¹ up to 493 K, possibly suggesting that water pre-adsorbed in the micropores of mordenite hindered the permeation of hydrogen. The hydrogen permeance dramatically increased to 6.5 × 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ at 503 K and reached to 1.4 × 10⁻⁶ mol m⁻² s⁻¹ Pa⁻¹ at 523 K because of the formation of cracks in the membrane. However, the membrane was thermally stabilized in the presence of steam and/or methanol.     

Decomposition of nitric oxide over perovskite oxide catalysts: effect of CO2, H2O and CH4

Direct nitric oxide decomposition over perovskites is fairly slow and complex, its mechanism changing dramatically with temperature. Previous kinetic study for three representative compositions (La_0.87Sr_0.13Mn_0.2Ni_0.8O_3−δ, La_0.66Sr_0.34Ni_0.3Co_0.7O_3−δ and La_0.8Sr_0.2Cu_0.15Fe_0.85O_3−δ) has shown that depending on the temperature range, the inhibition effect of oxygen either increases or decreases with temperature. This paper deals with the effect of CO₂, H₂O and CH₄ on the nitric oxide decomposition over the same perovskites studied at a steady-state in a plug-flow reactor with 1 g catalyst and total flowrates of 50 or 100 ml/min of 2 or 5% NO. The effect of carbon dioxide (0.5–10%) was evaluated between 873 and 923 K, whereas that of H₂O vapor (1.6 or 2.5%) from 723 to 923 K. Both CO₂ and H₂O inhibit the NO decomposition, but inhibition by CO₂ is considerably stronger. For all three catalysts, these effects increase with temperature. Kinetic parameters for the inhibiting effects of CO₂ and H₂O over the three perovskites were determined. Addition of methane to the feed (NO/CH₄=4) increases conversion of NO to N₂ about two to four times, depending on the initial NO concentration and on temperature. This, however, is still much too low for practical applications. Furthermore, the rates of methane oxidation by nitric oxide over perovskites are substantially slower than those of methane oxidation by oxygen. Thus, perovskites do not seem to be suitable for catalytic selective NO reduction with methane.     

Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

NO reduction by CH4 in the presence of O2 over La2O3 supported on Al2O3

Dispersing La₂O₃ on δ- or γ-Al₂O₃ significantly enhances the rate of NO reduction by CH₄ in 1% O₂, compared to unsupported La₂O₃. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La₂O₃ precursor used, the pretreatment, and the La₂O₃ loading. The most active family of catalysts consisted of La₂O₃ on γ-Al₂O₃ prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m²) occurred between the addition of one and two theoretical monolayers of La₂O₃ on the γ-Al₂O₃ surface. The best catalyst, 40% La₂O₃/γ-Al₂O₃, had a turnover frequency at 700°C of 0.05 s⁻¹, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La₂O₃/Al₂O₃ catalysts exhibited stable activity under high conversion conditions as well as high CH₄ selectivity (CH₄ + NO vs. CH₄ + O₂). The addition of Sr to a 20% La₂O₃/γ-Al₂O₃ sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO⁼₄ to the latter Sr-promoted La₂O₃/Al₂O₃ catalyst decreased activity although sulfate increased the activity of Sr-promoted La₂O₃. Dispersing La₂O₃ on SiO₂ produced catalysts with extremely low specific activities, and rates were even lower than with pure La₂O₃. This is presumably due to water sensitivity and silicate formation. The La₂O₃/Al₂O₃ catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications.     

Liquid-phase methanol synthesis in apolar (squalane) and polar (tetraethylene glycol dimethylether) solvents

The kinetics of the three-phase methanol synthesis over a commercial Cu–Zn–Al₂O₃ catalyst were studied in an apolar solvent, squalane and a polar solvent, tetraethylene glycol dimethylether (TEGDME). Experimental conditions were varied as follows: P=3.0–5.3 MPa, T=488–533 K and Φ_vG/w=7.5×10⁻³–8×10⁻³ Nm³ s⁻¹kg⁻¹_cat. The nature of the slurry–liquid influences the activation energy and the kinetic rate constant by interaction between adsorbed species and solvent and by competitive adsorption of the solvent on the catalyst surface. The rate of reaction to methanol observed in TEGDME appeared to be about 10 times lower than in squalane. TEGDME reduces the reaction rate, which is a disadvantage for its use as a solvent.     

Reduction of nitrite by sulfamic acid and sodium azide from aqueous solutions treated by gliding arc discharge

Nitrous and nitric acids form in aqueous solutions exposed to a gliding arc discharge burning in humid air. The anions interfere when the concentration of particular solutes such as pollutants must be determined. In particular they falsify the COD measurements and spectral investigations and thus the efficiency of the plasma treatment in pollutant abatement. The nitrite anions must be thus removed, which require specific reagents. The influence of parameters such as solution pH and [reducers]/[NO₂⁻] ratio on the reduction reaction was evaluated. The reduction of nitrite into N₂ either by sulfamic acid or sodium azide is a first-order pH-dependant reaction with regard to nitrite and reducers (k₁ = 2.93 × 10⁻¹ m³ kmol⁻¹ s⁻¹; k₂ = 6.21 × 10⁻¹ m³ kmol⁻¹ s⁻¹, respectively). Sodium azide is thus more reactive than sulfamic acid.     

Reversible sorption–desorption of NOx by mixed oxides under various atmospheres

Characteristics of MnO_y–ZrO₂ and Pt–ZrO₂–Al₂O₃ as reversible sorbents of NO_x were investigated under dynamic changes in atmosphere. These sorbents can be used reversibly with a change of C₃H₈ concentration in the reaction gases. Catalytic reduction of NO occurred in the presence of propane, which was more pronounced on Pt–ZrO₂–Al₂O₃ than on MnO_y-ZrO₂ due to high activity of Pt surface for this reaction on MnO_y in MnO_y–ZrO₂. The sorption was observed as soon as the atmosphere changed from a reducing to an oxidizing one. This implies that a high equilibrium partial pressure of O₂ is necessary for NO uptake since the sorbed NO⁻₃ species becomes stable. The beginning of NO_x desorption atmospheres was somewhat dependent on the amount of stored NO_x. The presence of propane in the gas phase strongly affected the characteristic sorption and desorption properties of MnO_y–ZrO₂ and Pt–ZrO₂–Al₂O₃. The sorption and desorption properties are different for MnO_y–ZrO₂ and Pt–ZrO₂–Al₂O₃, since the noble metal or metal oxide possesses unique activity for the NO reaction with C₃H₈ and the amount of oxygen available for oxidative sorption of NO.     

Lean NOx reduction with CO + H2 mixtures over Pt/Al2O3 and Pd/Al2O3 catalysts

The reduction of NO_x by hydrogen under lean burn conditions over Pt/Al₂O₃ is strongly poisoned by carbon monoxide. This is due to the strong adsorption and subsequent high coverage of CO, which significantly increases the temperature required to initiate the reaction. Even relatively small concentrations of CO dramatically reduce the maximum NO_x conversions achievable. In contrast, the presence of CO has a pronounced promoting influence in the case of Pd/Al₂O₃. In this case, although pure H₂ and pure CO are ineffective for NO_x reduction under lean burn conditions, H₂/CO mixtures are very effective. With a realistic (1:3) H₂:CO ratio, typical of actual exhaust gas, Pd/Al₂O₃ is significantly more active than Pt/Al₂O₃, delivering 45% NO_x conversion at 160 °C, compared to >15% for Pt/Al₂O₃ under identical conditions. The nature of the support is also critically important, with Pd/Al₂O₃ being much more active than Pd/SiO₂. Possible mechanisms for the improved performance of Pd/Al₂O₃ in the presence of H₂+CO are discussed.