Epitaxial and polycrystalline BaFe12O19 thin films grown by chemical vapour deposition

Epitaxial and polycrystalline barium hexaferrite BaFe₁₂O₁₉ thin films were prepared by metalorganic chemical vapour deposition (MOCVD). Films were grown by a liquid MOCVD technique which aim is to control precisely the precursor vapour pressures. Two kinds of substrates were used: sapphire (001) and silicon thermally oxidized. On Si/SiO₂ films are polycrystalline and the magnetization is isotropic. On Al₂O₃ (001), structural studies reveal the films to be predominantly single phase, well crystallized without annealing procedure and with the c-axis perpendicular to the film plane; epitaxial relationships between the film and the substrate were determined. The magnetic parameters, deduced from vibrating sample magnetometer measurements, show a high dependence of the magnetization with the orientation of the field with respect to the surface of the film.     

二次化学共沉淀法制备片状钡铁氧体的形成历程及磁性能研究

采用二次化学共沉淀法制备出六角或近六角片状BaFe₁₂O₁₉,其颗粒径向尺寸和径厚比分别为0.4-2μm和4-20。通过XRD、FTIR、TG/DTA及SEM/EDS分析技术研究了片状BaFe₁₂O₁₉的形成历程。结果表明:前驱体为非晶态BaCO₃、低结晶态Fe（OH）₃和晶态α-Fe₂O₃包覆原料BaFe₁₂O₁₉复合物;前驱体在焙烧过程中经过Fe（OH）₃脱水、BaCO₃分解反应、中间相α-Fe₂O₃和BaO反应得到终产物BaFe₁₂O₁₉。基于形成历程,六角片状BaFe₁₂O₁₉较原料BaFe₁₂O₁₉表现出显著提高的颗粒径向尺寸和径厚比、较高的纯度和略低的结晶有序程度,进而表现出明显提高的矫顽力、略低的饱和磁化强度和剩余磁化强度。     

Preparation of nanocrystalline SnO2 thin film coated Al2O3 ultrafine particles by fluidized chemical vapor deposition

Fluidized chemical vapor deposition (FCVD) technology was developed for coating SnO₂ thin film on Al₂O₃ ultrafine particles. TEM and HREM analysis found that SnO₂ films with different structures were deposited by controlling the coating temperature, reactant concentration, etc. Nanocrystalline SnO₂ film was coated at 573.15 K by gas phase reaction of SnCl₄ with H₂O. EPMA and EDS studies indicated that the distribution of SnO₂ inner and outer of the agglomerates was uniform. Nucleation and film deposition were coexisted mechanism during the FCVD coating process. The fraction of SnO₂ in the composite particles increased with increasing coating temperature, SnCl₄ concentration, and coating time. The mass fraction of SnO₂ in the composite particles increased strongly with the ratio of P_H2O and P_SnCl4 at low mole ratio of H₂O with SnCl₄, but increased little under the conditions of excess H₂O with respect to SnCl₄.     

Magnetic properties of BaFe12O19 smallparticles

The magnetic properties of small BaFe₁₂O₁₉ particles about 50 nm in size have been studied; the emphasis was on small-size effects. The compound formation of the hexagonal structure was made at a relatively low temperature; the small particle size made this result possible. As compared to the bulk value, a significantly reduced saturation magnetization is observed for these particles; this agrees with similar reports made earlier by several authors. To examine these phenomena further, Mossbauer spectra were obtained with high magnetic field applied longitudinally (H_ex=16.4 and 50 kOe). The spectra show the presence of recalcitrant spins where the spin configuration has a noncollinear arrangement that even a 50-kOe magnetic field does not remove. This hard-to-saturate component may lie in the surface layer of the Ba-ferrite small particles. The data also provide evidence that the Fe ions in the bipyramidal (2b) sites undergo magnetic-field-induced oscillations at 4.2 K     

Preparation and magnetic properties of barium hexaferrite nanorods

The barium hexaferrite nanorods were successfully prepared by sol–gel technique combined with polymethylmethacrylate as template. The crystal structure, morphology and magnetic properties of BaFe₁₂O₁₉ with different shape were investigated with X-ray diffraction, field emission scanning electron microscope and vibrating sample magnetometry. The results show that diameters and lengths of magnetic nanorods are about 60 nm and 300 nm, respectively. The coercivity of rod-shaped BaFe₁₂O₁₉ is increased to 5350 Oe, in comparison with 4800 Oe with plate-shape. The formation mechanism of BaFe₁₂O₁₉ nanorods and reasons resulting in high coercivity are discussed.     

Al2O3包覆Li1.2Mn0.54Ni0.13Co0.13O2富锂正极材料的电化学性能

用溶胶凝胶法制备了Li_1.2Mn_0.54Ni_0.13Co_0.13O₂富锂锰基正极材料,用均匀沉淀法对其进行不同比例Al₂O₃的表面包覆改性,并对其进行XRD、TEM表征和电化学性能分析。结果表明,包覆后的材料保持了原来的层状结构,Al₂O₃均匀地包覆在材料颗粒表面形成纳米级包覆层。在0.1C、2.0~4.8 V条件下Al₂O₃包覆量(质量分数)为0.7%的正极材料首次放电容量为251.3 mAh/g,首次库仑效率达到76.1%,100次循环后容量保持率达92.9%。包覆Al₂O₃抑制了循环过程中的电压衰减,适量的Al₂O₃包覆使正极材料的电化学性能提高。     

Al2O3基多孔隔热材料表面Al2O3/MoSi2涂层的制备及其性能

采用刷涂法在Al₂O₃基多孔隔热材料表面制备Al₂O₃/MoSi₂涂层,涂层以硅溶胶作为粘结剂,纳米Al₂O₃与Al₂O₃纤维作为耐高温组分,MoSi₂为高发射率组分。通过SEM、XRD对Al₂O₃/MoSi₂涂层微观表面结构、物相组成进行分析。研究纳米Al₂O₃与Al₂O₃纤维的质量比和MoSi₂含量对Al₂O₃/MoSi₂涂层耐温性能的影响,并对Al₂O₃/MoSi₂涂层的抗热震性能、发射率进行表征。结果表明,当纳米Al₂O₃与Al₂O₃纤维的质量比小于1∶1时,热考核后Al₂O₃/MoSi₂涂层表面无裂纹产生;当纳米Al₂O₃与Al₂O₃纤维的质量比在1∶2~1∶4之间时,Al₂O₃/MoSi₂涂层中的纤维网络较完整。MoSi₂的含量为20%时,Al₂O₃/MoSi₂涂层抗热震实验循环25次后表面保持完好,热考核后在2.5~25 μm波段的平均发射率在0.85左右,具有较高的发射率。      

Thickness dependence of structural and ferroelectric properties of sol-gel Pb(Zr0.56Ti0.44)0.90(Mg1/3Nb2/3)0.10O3 films

Sol-gel Pb(Zr_0.56Ti_0.44)_0.90(Mg_1/3Nb_2/3)_0.10O₃ (PZT-PMN) films were prepared onto the Ti/Pt/Ti bottom electrode by multilayer spin coating. The film thickness ranged from 0.22 to 0.88 μm. The Pt top electrodes were deposited on the PZT-PMN films by DC sputtering. The structural and ferroelectric properties of PZT-PMN films were investigated as a function of film thickness by X-ray diffraction (XRD), scanning electron microscopy (SEM), cross-sectional transmission electron microscopy (XTEM), and by measuring the relative permittivity. The film retains the tetragonal perovskite structure with the [111] and [100] preferred orientations perpendicular to the film surface independent of film thickness. The [100] texture increases with increasing film thickness although the [111] texture is always predominant. The film consists of columnar grains. The average grain size is nearly independent of film thickness. The surface layer containing fine grains about 30 nm in diameter is induced on the top of the film. As the film thickness exceeds 0.44 μm, the number of the fine grains decreases remarkably. The crystalline interface layer about 10 nm thick is formed between the film and the bottom electrode. This interface layer is composed of Pt, Pb, Zr, Ti and O, while it is rich in Ti and deficient in Pb and O as compared with the inside of the film. The measured relative permittivity of the film increases with increasing film thickness, following the low permittivity interface model. On the basis of this model, the relative permittivity is estimated to be 3200 for the intrinsic PZT-PMN film, 750 for the surface layer and 50 for the interface layer.     

自组装法制备磺化聚苯乙烯@Fe3O4磁性复合颗粒及其磁性能

实现结构可控、均匀包覆是制备核-壳复合材料的关键。采用离子交换法完成了磺化聚苯乙烯(PSS)表面Na+与溶液中Fe2+和Fe3+的交换,于碱性条件下制备了PSS表面负载Fe₃O₄(PSS@Fe₃O₄)的磁性复合颗粒。通过称重法计算了Fe₃O₄最大包覆率;通过振动样品磁强计(VSM)测试了不同负载含量下PSS@Fe₃O₄复合颗粒的磁性能;通过XRD、衰减全反射-FTIR (ATR-FTIR)、SEM-EDS分析了PSS@Fe₃O₄磁性复合颗粒的化学组成和微观结构。结果表明,随着Fe2+/Fe3+浓度增加,PSS@Fe₃O₄磁性颗粒的饱和磁化强度也随之增大,最大饱和磁化强度为7.51 emu/g,并具有明显的磁响应性;Fe₃O₄均匀包覆在PSS表面,最大包覆率为8.3 wt%。PSS@Fe₃O₄磁性复合颗粒有望用于磁流变、医学及水处理领域。      

Structural and magnetic properties of BaFe12-2xCoxTixO19 powders prepared by the glasscrystallization method

The glass crystallization method is shown to be suitable for preparing BaFe_12-2xCo_xTi_xO₁₉ powders with a nearly perfect crystallographic structure and a narrow particle size distribution. The dependences of the specific magnetization, the coercivity, and the particle size distribution on both the annealing temperature and the Co-Ti content correlate in a characteristic way. Furthermore, the lattice parameters, the specific surfaces and the thickness of the effective nonmagnetic surface layer were determined. The coercivity of the hexaferrite magnetic tapes is more than 8×10³ A/m higher than for the corresponding powders     

激光铝热还原法制备Al2O3/Ti-Al基复合涂层

利用Al和TiO₂之间的放热化学反应, 采用激光原位合成技术在TC4钛合金基体材料表面制备了Al₂O₃/Ti-Al金属间化合物基复合涂层。对比分析了激光功率、激光束扫描速度和光斑尺寸变化对激光能量密度变化量的影响程度, 借助X射线衍射仪(XRD)、光学显微镜(OM)、能谱仪(EDS)和显微硬度计分别考察了激光束扫描速度对复合涂层表面宏观形貌、截面显微组织结构和显微硬度的影响。结果显示, 扫描速度的变化对激光能量密度变化量的影响程度最大, 光斑尺寸次之, 激光功率的变化影响最弱。随着激光束扫描速度的增大, 复合涂层表面渐趋粗糙, “鱼鳞纹”状形貌特征趋于明显, 复合涂层与基材结合区厚度减小。激光原位复合涂层主要由k-Al₂O₃和α-Al₂O₃增强相与α-Ti和α₂-Ti₃Al基体相组成。随着激光束扫描速度增大, 复合涂层内k-Al₂O₃部分转变为α-Al₂O₃, Al₂O₃增强相有由枝晶状向纤维状转变的趋势; 复合涂层截面显微硬度自基体至涂层表面过度平缓, 且涂层区显微硬度分布均匀, 明显高于基材平均显微硬度。     

Si/Li4Ti5O12复合锂离子电池负极材料的制备、结构和电化学性能

本文以纳米Si为原料,通过溶胶-凝胶法,采用不同的煅烧温度,合成了在Si颗粒表面包覆Li4Ti5O12的复合结构材料作为锂离子电池负极材料。结合采用XRD、SEM、TEM、HRTEM和EDS等材料结构分析方法和对合成材料的首次库仑效率、循环稳定性及CV曲线的测试分析,研究了凝胶煅烧温度对合成材料的结构和电化学性能的影响,探讨了Li4Ti5O12的引入对改善Si负极材料循环性能的作用。研究结果表明,在600-800℃的煅烧温度下,溶胶-凝胶过程的产物主要为Li4Ti5O12,产物中Si保持其初始的晶体结构和颗粒特征。提高煅烧温度至1000℃,产物中出现相当量的杂相,大大降低了材料的容量。Si/Li4Ti5O12材料的首次充放电容量随煅烧温度的升高呈现先升高后又下降的变化,并在700℃获得最大值。Li4Ti5O12的引入较明显地改善了Si负极材料的循环稳定性。     

苯胺-SrTi(C2O4)2颗粒制备及其电流变性能

用沉淀法制备了苯胺-草酸氧钛锶（SrTi（C₂O₄）₂）颗粒。FTIR分析表明,苯胺已引入到SrTi（C₂O₄）₂颗粒的表面;XRD分析表明,苯胺-SrTi（C₂O₄）₂颗粒为含少量结晶的无定形态。采用SEM观察颗粒的形貌,结果表明,随反应体系中苯胺与钛原子物质的量比n_aniline/n_Ti的增大,苯胺-SrTi（C₂O₄）₂颗粒由近似球状（n_aniline/n_Ti =0）变为多面体状（n_aniline/n_Ti =2）,而后变为棒状与团簇状颗粒的混合体系（n_aniline/n_Ti =3）。以苯胺-SrTi（C₂O₄）₂颗粒为分散相制备颗粒质量分数为66.7%电流变液,电流变性能测试结果表明,在n_aniline/n_Ti =2时,电流变液具有较高的剪切应力和剪切屈服强度、较大的漏电流密度。苯胺在颗粒制备过程中起控制颗粒形貌的作用,在电流变液体系中起极性分子的作用,其对苯胺-SrTi（C₂O₄）₂电流变液性能的影响是两种效应综合作用的结果。     

五层纳米SiO2-Al2O3/聚酰亚胺复合薄膜的制备及性能

采用浸胶法制备了一系列SiO₂-Al₂O₃/聚酰亚胺（SiO₂-Al₂O₃/PI）五层耐电晕薄膜A_m A_n PA_n A_m,其中中间层（P）为纯PI薄膜,外层（A_m）、次外层（A_n）分别为SiO₂-Al₂O₃掺杂不同质量分数的纳米SiO₂-Al₂O₃/PI薄膜。采用TEM、FTIR、宽频介电谱仪、电导电流测试仪、耐电晕测试仪、介电强度测试仪和拉伸实验机对五层纳米复合PI耐电晕薄膜的微观结构、介电性能和力学性能进行了表征和测试。结果表明,SiO₂-Al₂O₃/PI复合薄膜掺杂层形成了分布均匀的有机/无机复合结构;SiO₂-Al₂O₃纳米粒子的保护作用是影响复合材料耐电晕性能的主要因素,复合薄膜A₃₂A₁₆PA₁₆A₃₂的耐电晕寿命最大,为23.4 h;外层掺杂量对五层SiO₂-Al₂O₃/PI复合材料的介电强度影响较大,复合薄膜A₂₀A₂₈PA₂₈A₂₀的介电强度最大,为302.3 kV/mm;通过对五层复合结构的设计,可以在兼顾材料力学性能的同时,提高其耐电晕寿命和介电强度。     

Fe3O4-MWCNTs在环氧树脂中的定向排列

用共沉淀法制备了具有超顺磁性Fe₃O₄-MWCNTs（多壁碳纳米管）复合粒子,加入环氧树脂（EP）中,在0.6 T的弱定磁场下固化成型。采用TEM研究其定向程度及分散性,并进行动态热机械分析、差热分析和导热率测试。结果表明,MWCNTs表面包覆了磁性Fe₃O₄纳米粒子,Fe₃O₄-MWCNTs复合物按照首尾衔接的方式沿着磁场方向定向排列。Fe₃O₄-MWCNTs/EP纳米复合材料表现出明显的各向异性,垂直于Fe₃O₄-MWCNTs轴向导热率低于平行方向的导热率,Fe₃O₄-MWCNTs的加入对于平行方向的导热率影响不大。Fe₃O₄-MWCNTs的加入使环氧树脂的储能模量变小,损耗模量变大,损耗因子均大于纯环氧树脂,表现出良好的阻尼性能。当Fe₃O₄-MWCNTs与EP质量比为0.3%时,损耗因子在20 ℃的温域内大于0.7,最高值达到1.16。     

可磁分离Fe3O4/g-C3N4复合材料的制备及其性能

为了利用Fe₃O₄的磁响应性及石墨相C₃N₄（g-C₃N₄）优良的光催化活性,首先采用高温热聚合法,以尿素为前驱体制备g-C₃N₄,然后采用水热法合成了可磁分离Fe₃O₄/g-C₃N₄复合材料。利用TEM、XRD、TGA、BET和振动样品磁强计（VSM）等多种测试手段表征分析Fe₃O₄/g-C₃N₄复合材料的形貌、晶型结构、比表面积、成分、饱和磁化强度等。通过模拟太阳光下Fe₃O₄/g-C₃N₄复合材料光催化吸附降解亚甲基蓝（MB）的实验,评价了Fe₃O₄/g-C₃N₄复合材料的吸附性能及光催化性能。结果表明,可磁分离Fe₃O₄/g-C₃N₄复合材料具有较大的比表面积,约为71.89 m²/g;且具有较好的磁性,饱和磁化强度为18.79 emu/g,可实现复合材料的分离回收;光照240 min时,Fe₃O₄/g-C₃N₄复合材料对MB的去除率为56.54%。所制备的Fe₃O₄/g-C₃N₄复合材料具有优良的吸附性能、光催化活性和磁性,并可通过外加磁场进行分离与回收。     

CoFe2与CoFe2O4质量比及MgO稀释对CoFe2@CoFe2O4磁性的影响

采用金属有机盐热分解方法制备了MgO包覆的CoFe₂O₄纳米粒子（CoFe₂O₄@MgO）,然后将CoFe₂O₄@MgO在H₂中还原,接着在空气中氧化制备了一组CoFe₂@CoFe₂O₄@MgO样品;用盐酸溶液溶解CoFe₂@CoFe₂O₄@MgO中的MgO获得另一组样品（CoFe₂@CoF₂O₄）。测量并绘制了CoFe₂@CoFe₂O₄@MgO和CoFe₂@CoF₂O₄的磁化强度随外磁场及温度变化的关系曲线。随着氧化温度升高,CoFe₂@CoFe₂O₄@MgO和CoFe₂@CoF₂O₄的矫顽力H_c、饱和磁化强度M_s、剩磁比M_r/M_s及磁有序状态发生显著变化,这些变化强烈依赖于磁性粒子的各向异性及粒子间的偶极相互作用。     

三基色镍基自敏复合涂层的制备及其性能研究

检测耐腐蚀涂层在腐蚀环境下的完整性, 对预测涂层工作寿命至关重要。通过电化学沉积法成功地将三基色无机荧光颗粒: BaMgAl₁₁O₁₇: Eu²⁺(蓝粉), Y₂O₃: Eu³⁺(红粉), CeMgAl₁₁O₁₉: Tb³⁺(绿粉)与金属镍复合, 在瓦特光亮镀镍浴中沉积出具有三基色指示功能的镍基自敏复合涂层。采用X射线衍射(XRD)、扫描电镜(SEM)、表面轮廓仪、维氏硬度计、荧光发射光谱和电化学测试手段分别对涂层组织形貌结构、润湿性、沉积率、硬度、发光性能及自敏性能进行了检测, 结果表明, 阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)和非离子表面活性剂聚乙二醇(PEG)可以有效提高三基色荧光粒子沉积率。三种荧光粒子与金属镍之间表现出不同的润湿性和匹配性, 使得其在镍基复合涂层中具有不同的作用: Y₂O₃: Eu³⁺荧光粒子改变了涂层结晶取向, 且使晶粒细化, BaMgAl₁₁O₁₇: Eu²⁺使涂层组织呈现节瘤状, Y₂O₃: Eu³⁺和CeMgAl₁₁O₁₉: Tb³⁺粒子明显提高了涂层硬度。三基色荧光粒子在腐蚀前后表现出不同的发光特性, 可以有效指示出涂层工作周期内的完整性, 起到良好的自敏检测作用。     

Long lasting phosphorescence of Sr4Al14O25:Eu,Dy thin films by magnetron sputtering

This paper reports the preparation process and the long lasting phosphorescence of the Sr₄Al₁₄O₂₅:Eu²⁺,Dy³⁺ thin films obtained by magnetron sputtering. Phosphorescence was achieved by annealing the films in reducing atmosphere. Sr₄Al₁₄O₂₅ thin film was obtained when the films were treated at 1200 °C, while SrAl₂O₄ was generated as the intermediate phase during the annealing process. Sr₄Al₁₄O₂₅:Eu²⁺,Dy³⁺ film generated an emission at 485 nm, and SrAl₂O₄:Eu²⁺,Dy³⁺ film showed an emission peaking at 515 nm. Afterglow characteristics were observed for both films, and Sr₄Al₁₄O₂₅:Eu²⁺,Dy³⁺ film showed a better afterglow property than the SrAl₂O₄:Eu²⁺,Dy³⁺ film due to a deeper trap level and a higher trap concentration formed in the thin films.     

CNTs添加对Cu-Al2O3复合材料耐电弧侵蚀性能的影响

Cu-Al₂O₃复合材料具有优异的传导性能和力学性能,在耐磨材料领域具有广阔的应用前景。为进一步提升电摩擦条件下复合材料的耐电弧侵蚀性能,本文采用内氧化法与粉末冶金法相结合制备了不同碳纳米管(CNTs)含量的CNTs/Cu-Al₂O₃复合材料,观察了CNTs/Cu-Al₂O₃复合材料中增强相的分布及其与基体界面结合情况,研究了添加不同含量CNTs对Cu-Al₂O₃复合材料传导性能和力学性能的影响,重点探究了CNTs/Cu-Al₂O₃复合材料的耐电弧侵蚀机制。结果表明：原位生成的纳米Al2O3颗粒钉扎位错及对CNTs分布具有调控作用,使CNTs弥散分布在铜基体中。与Cu-Al₂O₃复合材料相比,CNTs/Cu-Al₂O₃复合材料燃弧时间和燃弧能量明显降低,波动更平稳。在电弧侵蚀过程中,...