基于碳纳米管修饰电极的酶生物传感器研究进展

本文综述了基于碳纳米管修饰电极的酶生物传感器研究进展,介绍了碳纳米管修饰电极的发展及基于碳纳米管修饰电极的酶生物传感器的检测原理及分类;重点介绍了此类传感器在环境农药分析与生命科学分析中的应用。     

碳纤维布基聚吡咯修饰电极的制备及性能表征

分别用恒电流、恒电位、循环伏安法、电沉积与恒电流相结合等电化学方法,制备了新型碳纤维布基聚吡咯修饰电极,用扫描电子显微镜( SEM)观察了其表面形貌,研究了吡咯在碳纤维布基上的聚合条件和膜的生长过程,研究了聚吡咯修饰电极对氟离子的电流响应特性.结果表明:用电沉积与恒电流相结合的方法制备的碳纤维布基聚吡咯膜具有致密性好、...     

碳纤维布基聚吡咯修饰电极传感器检测茶叶中氟含量

采用恒电流聚合制得聚吡咯(PPy)膜修饰电极传感器,该电极传感器对氟离子(F-)具有一定的电流响应性能.进一步实验表明聚吡咯修饰电极传感器可用于快速检测茶叶中的氟离子.     

基于碳纳米管修饰电极的酶生物传感器研究进展

文章综述了基于碳纳米管修饰电极的酶生物传感器研究进展,介绍了碳纳米管修饰电极的发展及基于其的酶生物传感器;重点介绍了此类传感器在环境农药分析与生命科学分析中的应用。     

流通型碳纤维电极的电沉积行为

研究了电极构型对流通型碳纤维电极从ＡｕＣｌ－４稀溶液中电沉积金行为的影响．在顺流操作方式下，整个电极能够在极限电流条件下工作，利用电沉积分布曲线计算了传质系数与流速的关系式．逆流方式可以使电沉积分布更为均匀，从而提高整个电极的利用效率．利用数学模型对各种实验曲线进行了模拟，计算结果与实验结果相符．     

碳纤维复合管材电极电容式油位传感器及应用仪器

本发明属于计量测试技术及仪器领域,具体讲是涉及碳纤维复合管材电极电容式油位传感器及应用仪器。为提供碳纤维复合管材电极电容式油位传感器及应用仪器,该传感器及测量仪具有质量轻、结构更简单、制作工艺更简便的特点,     

一种纳米碳纤维盘电极的制备方法

本发明提供了一种纳米碳纤维盘电极的制备方法,该方法先将直径不超过10μm的碳纤维用银胶与金属丝粘连后穿入毛细管,并从毛细管中穿出一截;再将穿出毛细管的碳纤维尖端用火焰蚀刻至纳米尺度;然后将碳纤维尖端撤回至毛     

聚乙二醇对碳纤维电极材料性能的影响

以聚乙二醇为改性剂,采用静电纺丝法制备聚丙烯腈纤维。经预氧化、碳化过程制备了聚丙烯腈基碳纤维。用SEM、XRD等手段表征了碳纤维的微观形貌及结构。用XPS测试表征了碳纤维表面元素含量。用循环伏安测试法测试碳纤维电极材料的电化学性能。实验结果表明,当聚乙二醇加入量为4％时,得到的碳纤维电极材料电容性能最佳,其比电容值达到126．84F／g。     

以萘酚绿B为媒介体的银溶胶-葡萄糖氧化酶生物传感器的研究

用聚乙烯醇缩丁醛将葡萄糖氧化酶(GOD)和纳米银固定于铂丝电极上并采用萘酚绿B作为电子媒介制得了新型葡萄糖酶生物传感器。实验发现,吸附在纳米银表面上的酶稳定且保持生物活性,电子媒介体与纳米银结合显著提高了该传感器的灵敏度。讨论了溶解性媒介体萘酚绿的浓度、溶液的pH值和温度对该电极电流响应的影响。该传感器在优化的实验条件下,对葡萄糖表现出良好的响应特性,如响应快、重现性和稳定性好,传感器线性范围为1.0×10-3~4.0×10-2mol/L,检出限为3.0×10-4mol/L。抗坏血酸、尿酸等对测定均无干扰。     

海藻酸钙凝胶固定葡萄糖氧化酶的研究

利用海藻酸钙凝胶颗粒固定葡萄糖氧化酶(GOD).确定了固定化条件,并考察了温度、pH值、储存时间对固定化酶和游离酶酶活力的影响,测定了酶活回收率.确定的固定化较优条件为:CaCl2 5.0%(质量体积比),海藻酸钠3.0%(质量体积比);固定化酶的最适催化温度为31℃、最适pH值为6.3,较游离酶分别提高7℃和0.6;固定化酶的平均酶活回收率为61.69%.此外,酶的储存稳定性能也有所提高,可重复多次使用.     

含超细Au颗粒的乳酸氧化酶和葡萄糖氧化酶生物传感器

制备了小于10 nm的金颗粒,并利用其进行固定化葡萄糖氧化酶和乳酸氧化酶的研究. 实验发现,金纳米颗粒可以大幅度提高葡萄糖氧化酶电极和乳酸氧化酶电极的电流响应,响应电流从相应浓度的几十纳安增强到几千纳安. 探讨了金纳米颗粒在固定化酶中所起的作用.     

碳纳米管复合物修饰电极制备及分析应用

将二氧化钛水凝胶与多壁碳纳米管复合后修饰到玻碳电极表面制备H2O2生物传感器。采用循环伏安法对电极性能进行了表征,探讨了制备及测试最佳条件,用电流-时间曲线法检测样品中H2O2含量。该修饰电极具有响应速度快(<0.5 s)、灵敏和选择性好、还原峰电位(-0.28 V)低等特点。线性范围4.0×10-4~13.0 mmol/L,检测限0.12μmol/L。     

Glucose-Sensitive Liposomes Incorporating Hydrophobically Modified Glucose Oxidase

Glucose-sensitive liposomes were prepared by incorporating hydrophobically modified glucose oxidase (EC 1.1.3.4.) into the liposomal bilayer of dioleoylphosphatidylethanolamine and cholesteryl hemisuccinate. For the release test, calcein, a fluorescence marker, was entrapped in the liposomes. The liposomes were stable under neutral conditions in terms of calcein release but an extensive release was observed under acidic conditions. In the experiment of glucose concentration-dependent calcein release, no release was observed for 180 min when the suspension of liposome was free of glucose. With a glucose concentration of 50 mg/dL, no appreciable amount of calcein was released for the first 20 min, and then the release rate was accelerated. At 200 mg/dL glucose concentration which is diagnostic and indicative for insulin-dependent diabetes, the lag time of calcein release became shorter and a faster response was obtained. When glucose concentration further increased to 400 mg/dL, the calcein release rate and the degree of release in 180 min were almost the same as the values when the glucose concentration was 200 mg/dL. The glucose concentration-dependent release is due to pH change, since the suspension of liposomes became acidic during the release experiments.     

泡沫碳纤维材料的生产

介绍了泡沫碳纤维制品的生产工艺。讨论了粘合剂浓度、短碳纤维表面处理、固化时间对产品性能的影响。     

A New Amperometric Glucose Biosensor Based on Pectin Coating

In this article we describe the preparation and characterization of a new glucose oxidase (GOD) biosensor. The GOD biosensor was immobilized onto pectin by using chromium III sulfate and electrode was coated with GOD containing pectin. Immobilization conditions were modified according to the results obtained by coated electrode. Optimum conditions were obtained when 10 U GOD and 1% pectin was reacted with 0.01 M chromium III sulfate. Developed biosensor is very accurate, fast responding, and stable. We could easily detect 1 mM glucose with a response time below 1 minute and could use our sensor up to 14 times (within 27 days) with 90% accuracy.     

纳米CdS∶Cu双酶膜葡萄糖生物传感器

将纳米CdS∶Cu颗粒加入到葡萄糖酶(GOD)和辣根过氧化物酶(HRP)双酶膜中,与导电聚合物聚邻苯二胺(PoPD)经电化学聚合反应而固定此两酶,制备了电流型纳米CdS∶Cu颗粒双酶膜葡萄糖生物传感器,分析了CdS∶Cu纳米颗粒对传感器电流响应的影响,进行了传感器的性能测定。实验表明,引入CdS∶Cu纳米粒子和PoPD后可显著改进传感器响应性能,线性范围为0.55~9.2 mmol/L,检测下限为0.55 mmol/L,响应时间为20 s。稳定工作215天,传感器活性指标无显著变化,且抗干扰性强。     

Orientated Immobilization of FAD-Dependent Glucose Dehydrogenase on Electrode by Carbohydrate-Binding Module Fusion for Efficient Glucose Assay

The discovery or engineering of fungus-derived FAD-dependent glucose 1-dehydrogenase (FAD-GDH) is especially important in the fabrication and performance of glucose biosensors. In this study, a novel FAD-GDH gene, phylogenetically distantly with other FAD-GDHs from Aspergillus species, was identified. Additionally, the wild-type GDH enzyme, and its fusion enzyme (GDH-NL-CBM2) with a carbohydrate binding module family 2 (CBM2) tag attached by a natural linker (NL), were successfully heterogeneously expressed. In addition, while the GDH was randomly immobilized on the electrode by conventional methods, the GDH-NL-CBM2 was orientationally immobilized on the nanocellulose-modified electrode by the CBM2 affinity adsorption tag through a simple one-step approach. A comparison of the performance of the two electrodes demonstrated that both electrodes responded linearly to glucose in the range of 0.12 to 40.7 mM with a coefficient of determination R² > 0.999, but the sensitivity of immobilized GDH-NL-CBM2 (2.1362 × 10⁻² A/(M*cm²)) was about 1-fold higher than that of GDH (1.2067 × 10⁻² A/(M*cm²)). Moreover, a lower detection limit (51 µM), better reproducibility (<5%) and stability, and shorter response time (≈18 s) and activation time were observed for the GDH-NL-CBM2-modified electrode. This facile and easy immobilization approach used in the preparation of a GDH biosensor may open up new avenues in the development of high-performance amperometric biosensors.     

碳纤维增强环氧树脂基复合材料镀覆预处理技术探讨

简介了碳纤维复合材料(CFRP)材料表面金属化的工艺过程,采用CrO3-H2SO4溶液对CFRP进行蚀刻处理,通过扫描电镜观测经蚀刻处理后的树脂表面的微观形貌,测试了镀层附着力,分析了蚀刻程度与镀层附着力之间的关系。实验表明,CFRP材料镀覆前的适度蚀刻处理对后续的镀层附着力来说至关重要,蚀刻过度或不足都难以获得满意附着力的镀层。