Comparison of dimethyl sulfoxide treated highly conductive poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) electrodes for use in indium tin oxide-free organic electronic photovoltaic devices

Indium tin oxide (ITO)-free organic photovoltaic (OPV) devices were fabricated using highly conductive poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as the transparent conductive electrode (TCE). The intrinsic conductivity of the PEDOT:PSS films was improved by two different dimethyl sulfoxide (DMSO) treatments – (i) DMSO was added directly to the PEDOT:PSS solution (PEDOT:PSS_ADD) and (ii) a pre-formed PEDOT:PSS film was immersed in DMSO (PEDOT:PSS_IMM). X-ray photoelectron spectroscopy (XPS) and conductive atomic force microscopy (CAFM) studies showed a large amount of PSS was removed from the PEDOT:PSS_IMM electrode surface. OPV devices based on a poly(3-hexylthiophene):[6,6]-phenyl-C₆₁-butyric acid methyl ester (P3HT:PCBM) bulk hetrojunction showed that the PEDOT:PSS_IMM electrode out-performed the PEDOT:PSS_ADD electrode, primarily due to an increase in short circuit current density from 6.62 mA cm⁻² to 7.15 mA cm⁻². The results highlight the importance of optimising the treatment of PEDOT:PSS electrodes and demonstrate their potential as an alternative TCE for rapid processing and low-cost OPV and other organic electronic devices.     

A Simple Cu(II) Polyelectrolyte as a Method to Increase the Work Function of Electrodes and Form Effective p-Type Contacts in Perovskite Solar Cells

One effective strategy to improve the performance of perovskite solar cells (PSCs) is to develop new hole transport layers (HTLs). In this work, a simple polyelectrolyte HTL, copper (II) poly(styrene sulfonate) (Cu:PSS), which comprises easily reduced Cu²⁺ counter-ions with an anionic PSS polyelectrolyte backbone is investigated. Photoelectron spectroscopy reveals an increase in the work function of the anode and upward band bending effect upon incorporation of Cu:PSS in PSC devices. Cu:PSS shows a synergistic effect when mixed with polyethylenedioxythiophene: polystyrenesulfonate (PEDOT:PSS) in various proportions and results in a decrease in the acidity of PEDOT:PSS as well as reduced hysteresis in completed devices. Cu:PSS functions effectively as a HTL in PSCs, with device parameters comparable to PEDOT:PSS, while mixtures of Cu:PSS with PEDOT:PSS shows greatly improved performance compared to PEDOT:PSS alone. Optimized devices incorporating Cu:PSS/PEDOT:PSS mixtures show an improvement in efficiency from 14.35 to 19.44% using a simple CH₃NH₃PbI₃ active layer in an inverted (P-I-N) geometry, which is one of the highest values yet reported for this type of device. It is expected that this type of HTL can be employed to create p-type contacts and improve performance in other types of semiconducting devices as well.     

Thermoelectric Properties of Polymeric Mixed Conductors

The thermoelectric (TE) phenomena are intensively explored by the scientific community due to the rather inefficient way energy resources are used with a large fraction of energy wasted in the form of heat. Among various materials, mixed ion‐electron conductors (MIEC) are recently being explored as potential thermoelectrics, primarily due to their low thermal conductivity. The combination of electronic and ionic charge carriers in those inorganic or organic materials leads to complex evolution of the thermovoltage (V_oc) with time, temperature, and/or humidity. One of the most promising organic thermoelectric materials, poly(3,4‐ethyelenedioxythiophene)‐polystyrene sulfonate (PEDOT‐PSS), is an MIEC. A previous study reveals that at high humidity, PEDOT‐PSS undergoes an ionic Seebeck effect due to mobile protons. Yet, this phenomenon is not well understood. In this work, the time dependence of the V_oc is studied and its behavior from the contribution of both charge carriers (holes and protons) is explained. The presence of a complex reorganization of the charge carriers promoting an internal electrochemical reaction within the polymer film is identified. Interestingly, it is demonstrated that the time dependence behavior of V_oc is a way to distinguish between three classes of polymeric materials: electronic conductor, ionic conductor, and mixed ionic–electronic conductor.     

PEDOT:PSS‐Assisted Exfoliation and Functionalization of 2D Nanosheets for High‐Performance Organic Solar Cells

Here, a facial and scalable method for efficient exfoliation of bulk transition metal dichalcogenides (TMD) and graphite in aqueous solution with poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) to prepare single‐ and few‐layer nanosheets is demonstrated. Importantly, these TMD nanosheets retain the single crystalline characteristic, which is essential for application in organic solar cells (OSCs). The hybrid PEDOT:PSS/WS₂ ink prepared by a simple centrifugation is directly integrated as a hole extraction layer for high‐performance OSCs. Compared with PEDOT:PSS, the PEDOT:PSS/WS₂‐based devices provide a remarkable power conversion efficiency due to the “island” morphology and benzoid–quinoid transition. This study not only demonstrates a novel method for preparing single‐ and few‐layer TMD and graphene nanosheets but also paves a way for their applications without further complicated processing.     

Electrical characterization of inorganic-on-organic diode based InP and poly(3,4-ethylenedioxithiophene)/poly(styrenesulfonate) (PEDOT:PSS)

The electronic properties of metal–organic semiconductor-inorganic semiconductor diode between InP and poly(3,4-ethylenedioxithiophene)/poly(styrenesulfonate) (PEDOT:PSS) polymeric organic semiconductor film have been investigated via current–voltage and capacitance–voltage methods. The Al/PEDOT:PSS/p-InP contact exhibits a rectification behavior with the barrier height value of 0.98 eV and with the ideality factor value of 2.6 obtained from their forward bias current voltage (I–V) characteristics at the room temperature greater than the conventional Al/p-InP (0.83 eV, n = 1.13). This increase in barrier height and ideality factor can be attributed to PEDOT:PSS film formed at Al/p-InP interface.     

High efficiency bulk heterojunction organic solar cell by using high conductivity modified PEDOT: PSS as a buffer layer

In this paper,bulk heterojunction solar cells with poly-(3-hexylthiophene)(P3HT):[6,6]-phenyl-C61-butyric-acid-methylester(PCBM) as an active layer and modified poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)(PEDOT:PSS) as a buffer layer are fabricated.The buffer layer is modified by adding 1% to 5% dimethyl sulfoxide(DMSO) into PEDOT:PSS solution before spin-coating.The conductivity of modified PEDOT:PSS and the performance of solar cells with modified PEDOT:PSS are measured.The highest conductivity of modified PEDOT:PSS with 4% DMSO can achieve 89.693 S/cm.The performance of organic solar cell with PEDOT:PSS modified by 4% DMSO is the best.The 4% DMSOmodified-PEDOT:PSS cell has a power conversion efficiency of 3.34%,V oc of 5.7 V,J sc of 14.56 mA/cm 2 and filling factor(FF) of 40.34%.     

Highly Conductive and Transparent PEDOT:PSS Films with a Fluorosurfactant for Stretchable and Flexible Transparent Electrodes

Highly conductive and transparent poly‐(3,4‐ethylenedioxythiophene):poly(styrenesulfonic acid) (PEDOT:PSS) films, incorporating a fluorosurfactant as an additive, have been prepared for stretchable and transparent electrodes. The fluorosurfactant‐treated PEDOT:PSS films show a 35% improvement in sheet resistance (R_s) compared to untreated films. In addition, the fluorosurfactant renders PEDOT:PSS solutions amenable for deposition on hydrophobic surfaces, including pre‐deposited, annealed films of PEDOT:PSS (enabling the deposition of thick, highly conductive, multilayer films) and stretchable poly(dimethylsiloxane) (PDMS) substrates (enabling stretchable electronics). Four‐layer PEDOT:PSS films have an R_s of 46 Ω per square with 82% transmittance (at 550 nm). These films, deposited on a pre‐strained PDMS substrate and buckled, are shown to be reversibly stretchable, with no change to R_s, during the course of over 5000 cycles of 0 to 10% strain. Using the multilayer PEDOT:PSS films as anodes, indium tin oxide (ITO)‐free organic photovoltaics are prepared and shown to have power conversion efficiencies comparable to that of devices with ITO as the anode. These results show that these highly conductive PEDOT:PSS films can not only be used as transparent electrodes in novel devices (where ITO cannot be used), such as stretchable OPVs, but also have the potential to replace ITO in conventional devices.     

Hole Injection in a Model Fluorene–Triarylamine Copolymer

Recent developments in synthesis and purification have yielded conjugated polymers with hole mobilities exceeding 0.01 cm² V^?1 s^?1. Essential to harvesting the potential of these materials in organic light emitting diodes (OLEDs) is the identification of suitable ohmic contacts. Using a model fluorene copolymer that shows high‐mobility, non‐dispersive hole transport, it is demonstrated that electrodes commonly used as anodes in OLEDs are very poor hole injectors. Injection from Au and indium tin oxide anodes is limited by energy barriers of 0.75 and 0.65 eV, respectively, and the injected current is found to be temperature independent—a prediction that was not reproduced by the leading injection model for disordered organic semiconductors. Injection from a poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonate) (PEDOT:PSS) anode, on the other hand, is found to become less efficient with electric field, a behavior which is currently not understood. In thinner poly[(9,9′‐dioctylfluorenyl‐2,7‐diyl)‐co‐(4,4′‐(N‐(4‐sec‐butyl))diphenylamine)] films, which are of relevance to OLEDs, ohmic losses on the PEDOT:PSS layer are found to limit the flow of current. These results illustrate the opportunity to further improve the performance of OLEDs as well as the challenge posed by high mobility conjugated polymers for the design of hole injection layers.     

Screen‐Printed Poly(3,4‐Ethylenedioxythiophene):Poly(Styrenesulfonate) Grids as ITO‐Free Anodes for Flexible Organic Light‐Emitting Diodes

Poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT: PSS) grids have been successfully constructed by roll‐to‐roll compatible screen‐printing techniques and have been used as indium tin oxide (ITO)‐free anodes for flexible organic light‐emitting diodes (OLEDs). The grid‐type transparent conductive electrodes (TCEs) can adopt thicker PEDOT: PSS grid lines to ensure the conductivity, while the mesh‐like grid structure can play an important role to maintain high optical transparency. By adjusting grid periods, grid thickness and treatment of organic additives, PEDOT: PSS TCEs with high optical transparency, low sheet resistance, and excellent mechanical flexibility have been achieved. Using the screen‐printed PEDOT: PSS grids as the anodes, ITO‐free OLEDs achieved peak current efficiency of 3.40 cd A^?1 at the current density of 10 mA cm^?2, which are 1.56 times better than the devices with ITO glass as the anodes. The improved efficiency is attributed to the light extraction effect and improved transparency by the grid structure. The superior optoelectronic performances of OLEDs based on flexible screen‐printed PEDOT: PSS grid anodes suggest their great prospects as ITO‐free anodes for flexible and wearable electronic applications.     

High‐Conductivity Poly(3,4‐ethylenedioxythiophene):Poly(styrene sulfonate) Film and Its Application in Polymer Optoelectronic Devices

The conductivity of a poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) film can be enhanced by more than two orders of magnitude by adding a compound with two or more polar groups, such as ethylene glycol, meso‐erythritol (1,2,3,4‐tetrahydroxybutane), or 2‐nitroenthanol, to an aqueous solution of PEDOT:PSS. The mechanism for this conductivity enhancement is studied, and a new mechanism proposed. Raman spectroscopy indicates an effect of the liquid additive on the chemical structure of the PEDOT chains, which suggests a conformational change of PEDOT chains in the film. Both coil and linear conformations or an expanded‐coil conformation of the PEDOT chains may be present in the untreated PEDOT:PSS film, and the linear or expanded‐coil conformations may become dominant in the treated PEDOT:PSS film. This conformational change results in the enhancement of charge‐carrier mobility in the film and leads to an enhanced conductivity. The high‐conductivity PEDOT:PSS film is ideal as an electrode for polymer optoelectronic devices. Polymer light‐emitting diodes and photovoltaic cells fabricated using such high‐conductivity PEDOT:PSS films as the anode exhibit a high performance, close to that obtained using indium tin oxide as the anode.     

Aging process of PEDOT:PSS dispersion and robust recovery of aged PEDOT:PSS as a hole transport layer for organic solar cells

Conducting p-type polymer of poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) has been widely used for organic optoelectronics, particularly as a hole transport layer for organic solar cells. While the aged PEDOT:PSS dispersion impacts device performance, the aging of PEDOT:PSS dispersion have not been well investigated. Moreover, the recovery process of aged (two-year-old) PEDOT:PSS dispersion has not been demonstrated yet. Herein, it is found that aqueous PEDOT:PSS dispersion undergoes extensive phase separation during the aging process, resulting in both nanoscale and macroscale hydrophobic PEDOT-rich agglomerates. When the aged PEDOT:PSS thin film is integrated into P3HT:PCBM organic solar cells, the PEDOT-rich agglomerates trap the photogenerated holes at the PEDOT:PSS/P3HT interface, resulting in poor extraction efficiency in organic solar cells. To recover a hole transport functionality from aged PEDOT:PSS, three different solvents such as isopropyl alcohol (C₃H₇OH), ethanol (C₂H₅OH) and methanol (CH₃OH) are investigated. Among them, it is found that isopropyl alcohol (IPA) yielded very uniform PEDOT:PSS thin film layer. This is because hydrophobic functional groups of IPA solvent facilitated the preferential solvation of phase separated hydrophobic PEDOT-rich agglomerates. However, when non-optimal concentration of IPA solvents was added into the aged PEDOT:PSS dispersion, the size of PEDOT-rich agglomerates was adversely enlarged. When organic solar cells were fabricated using more than a two-year-old PEDOT:PSS that was treated with IPA solvent, the resulting device performance of organic solar cells was fully recovered and became comparable or better than that of organic solar cells fabricated with fresh PEDOT:PSS.     

Interface Modification to Improve Hole‐Injection Properties in Organic Electronic Devices

The performance of organic electronic devices is often limited by injection. In this paper, improvement of hole injection in organic electronic devices by conditioning of the interface between the hole‐conducting layer (buffer layer) and the active organic semiconductor layer is demonstrated. The conditioning is performed by spin‐coating poly(9,9‐dioctyl‐fluorene‐co‐N‐ (4‐butylphenyl)‐diphenylamine) (TFB) on top of the poly(3,4‐ethylene dioxythiophene): poly(styrene sulfonate) (PEDOT:PSS) buffer layer, followed by an organic solvent wash, which results in a TFB residue on the surface of the PEDOT:PSS. Changes in the hole‐injection energy barriers, bulk charge‐transport properties, and current–voltage characteristics observed in a representative PFO‐based (PFO: poly(9,9‐dioctylfluorene)) diode suggest that conditioning of PEDOT:PSS surface with TFB creates a stepped electronic profile that dramatically improves the hole‐injection properties of organic electronic devices.     

Scaling Effects on the Electrochemical Performance of poly(3,4‐ethylenedioxythiophene (PEDOT), Au,and Pt for Electrocorticography Recording

Reduced contact size would permit higher resolution cortical recordings, but the effects of diameter on crucial recording and stimulation properties are poorly understood. Here, the first systematic study of scaling effects on the electrochemical properties of metallic Pt and Au and organic poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) electrodes is presented. PEDOT:PSS exhibits better faradaic charge transfer and capacitive charge coupling than metal electrodes, and these characteristics lead to improved electrochemical performance and reduced noise at smaller electrode diameters. PEDOT:PSS coating reduces the impedances of metallic electrodes by up to 18x for diameters <200 µm, but has no effect for millimeter scale contacts due to the dominance of series resistances. Therefore, the performance gains are especially significant at smaller diameters and lower frequencies essential for recording cognitive and pathological activities. Additionally, the overall reduced noise of the PEDOT:PSS electrodes enables a lower noise floor for recording action potentials. These results permit quantitative optimization of contact material and diameter for different electrocorticography applications.     

Optimization of electrohydrodynamic-printed organic electrodes for bottom-contact organic thin film transistors

In this study, we investigate the optimization of printed (3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) as source/drain electrodes for organic thin film transistors (OTFTs) through electrohydrodynamic (EHD) printing process. The EHD-printed PEDOT:PSS electrodes should fulfill the prerequisites of not only high conductivity but also optimum surface tension for successful jetting. The conductivity of PEDOT:PSS was dramatically enhanced from 0.07 to 352 S/cm by the addition of dimethylsulfoxide (DMSO). To use the DMSO-treated PEDOT:PSS solution in the EHD printing process, its surface tension was optimized by the addition of surfactant (Triton X-100), which was found to enable various jetting modes. In the stable cone-jet mode, the patterning of the modified PEDOT:PSS solution was realized on the surface-functionalized SiO₂ substrates; the printed line widths were in the range 384 to 81 μm with a line resistance of 8.3 × 10³ Ω/mm. In addition, pentacene-based OTFTs employing the EHD-printed PEDOT:PSS as source and drain electrodes were found to exhibit electrical performances superior to an equivalent vacuum-deposited Au-based device.     

Near‐Infrared Absorbing Polymeric Nanoparticles as a Versatile Drug Carrier for Cancer Combination Therapy

Poly(3,4‐ethylenedioxythiophene):poly(4‐styrenesulfonate) (PEDOT:PSS) nanoparticles, after being coated with polyethylene glycol (PEG), are used as a drug carrier to load various types of aromatic therapeutic molecules, including chemotherapy drugs doxorubicin (DOX) and SN38, as well as a photodynamic agent chlorin e6 (Ce6), through π–π stacking and hydrophobic interaction. Interesting functionalities of PEDOT:PSS‐PEG as an unique versatile drug delivery platform are discovered. Firstly, for water‐insoluble drugs such as SN38, the loading on PEDOT:PSS‐PEG dramatically enhances its water solubility, while maintaining its cytotoxicity to cancer cells. Secondly, the delivery of Ce6 by PEDOT:PSS‐PEG is able to remarkably accelerate the cellular uptake of Ce6 molecules, and thus offers improved photodynamic therapeutic efficacy. Using DOX‐loaded PEDOT:PSS‐PEG as the model system, it is demonstrated that the photothermal effect of PEDOT:PSS‐PEG can be utilized to promote the delivery of this chemotherapeutic agent, achieving a combined photothermal‐ and chemotherapy with an obvious synergistic cancer killing effect. Moreover, it is also shown that multiple types of therapeutic agents could be simultaneously loaded on PEDOT:PSS‐PEG nanoparticles and delivered into cancer cells. This work highlights the great potential of NIR‐absorbing polymeric nanoparticles as multifunctional drug carriers for potential cancer combination therapy with high efficacy.     

Functional Metal–Organic Frameworks for Maximizing Transconductance of Organic Photoelectrochemical Transistor at Zero Gate Bias and Biological Interfacing Application

Organic electrochemical transistors showing maximum transconductance (g_m) at zero gate bias (V_G) is desired but has long been a challenge. To date, few solutions to this issue are available. Light-matter interplay is shown as rich sources for optogenetics, photodynamic therapy, and advanced electronics, but its potential in g_m modulation are largely untapped. Herein, the challenge is addressed by unique light-matter interplay in the newly emerged technique of organic photoelectrochemical transistor (OPECT), which is exemplified by dual-ligand photosensitive metal–organic frameworks (DL-PS-MOFs)/TiO₂ nanorods (NRs) gated poly(ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) OPECT under 425 nm light irradiation. Interestingly, the light stimulation on the DL-PS-MOFs can de-dope PEDOT:PSS with altered transistor physics, achieving device showing maximum g_m at zero V_G and the simultaneous superior output of channel current. In connection to a cascade catalytic hairpin assembly-rolling circle amplification strategy, such a device is then biologically interfaced with a miRNA-triggered growth of DNA spheres for the sensitive detection of miRNA-21 down to 0.12 fm . This work features a proof-of-concept study using light-matter interplay to enable organic transistors showing maximum g_m at zero V_G and its sensitive biological interfacing application.     

Quasi‐One Dimensional in‐Plane Conductivity in Filamentary Films of PEDOT:PSS

The mechanism and magnitude of the in‐plane conductivity of poly(3,4‐ethy‐lenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) thin films is determined using temperature dependent conductivity measurements for various PEDOT:PSS weight ratios with and without a high boiling solvent (HBS). Without the HBS the in‐plane conductivity of PEDOT:PSS is lower and for all studied weight ratios well described by the relation $ \sigma = \sigma _0 {\rm exp}[- \left({{{{T_0}}\over{T}}} \right)^{0.5}] $ with T₀ a characteristic temperature. The exponent 0.5 indicates quasi‐one dimensional (quasi‐1D) variable range hopping (VRH). The conductivity prefactor σ₀ varies over three orders of magnitudes and follows a power law σ₀∝c^3.5_PEDOT with c_PEDOT the weight fraction of PEDOT in PEDOT:PSS. The field dependent conductivity is consistent with quasi‐1D VRH. Combined, these observations suggest that conductance takes place via a percolating network of quasi‐1D filaments. Using transmission electron microscopy (TEM) filamentary structures are observed in vitrified dispersions and dried films. For PEDOT:PSS films with HBS, the conductivity also exhibits quasi‐1D VRH behavior when the temperature is less than 200 K. The low characteristic temperature T₀ indicates that HBS‐treated films are close to the critical regime between a metal and an insulator. In this case, the conductivity prefactor scales linearly with c_PEDOT, indicating the conduction is no longer limited by a percolation of filaments. The lack of observable changes in TEM upon processing with the HBS suggests that the changes in conductivity are due to a smaller spread in the conductivities of individual filaments, or a higher probability for neighboring filaments to be connected rather than being caused by major morphological modification of the material.     

High‐Performance Metal‐Free Solar Cells Using Stamp Transfer Printed Vapor Phase Polymerized Poly(3,4‐Ethylenedioxythiophene) Top Anodes

The use of vapor phase polymerized poly(3,4‐ethylenedioxythiophene) (VPP‐PEDOT) as a metal‐replacement top anode for inverted solar cells is reported. Devices with both i) standard bulk heterojunction blends of poly(3‐hexylthiophene) (P3HT) donor and 1‐(3‐methoxycarbonyl)‐propyl‐1‐phenyl‐(6,6)C₆₀ (PCBM) soluble fullerene acceptor and ii) hybrid inorganic/organic TiO₂/P3HT acceptor/donor active layers are studied. Stamp transfer printing methods are used to deposit both the VPP‐PEDOT top anode and a work function enhancing PEDOT:polystyrenesulphonate (PEDOT:PSS) interlayer. The metal‐free devices perform comparably to conventional devices with an evaporated metal top anode, yielding power conversion efficiencies of 3% for bulk heterojunction blend and 0.6% for organic/inorganic hybrid structures. These encouraging results suggest that stamp transfer printed VPP‐PEDOT provides a useful addition to the electrode materials tool‐box available for low temperature and non‐vacuum solar cell fabrication.     

Robust High Thermoelectric Harvesting Under a Self‐Humidifying Bilayer of Metal Organic Framework and Hydrogel Layer

Robust thermoelectric harvesting is explored from a proton‐doped mixed ionic conductive (PMIC) film under water‐harvesting metal organic framework (MOF) film coupled with hydrogel layer (MOF/HG). As a PMIC, highly doped poly(3,4‐ethylenedioxythiophene)s with poly(styrene sulfonate) (PEDOT:PSS) is prepared by precisely controlling the proton doping to afford a stable and high thermoelectric PMIC. Among the PMICs, the PEDOT:PSS film doped with 30 wt% of poly(styrene sulfonic acid) (PSSH) recorded a Seebeck coefficient of over 16.2 mV K^?1 and a thermal voltage of 81 mV for a temperature gradient (ΔT) of 5 K. The thermal charging on PMICs afforded high thermal voltage and current output, reproducibly, to show cumulative thermoelectric nature. Environmentally sustainable thermoelectric harvesting is achieved from a PMIC under a MOF/HG, prepared by water‐harvesting MOF‐801 coupled with a HG layer, to provide constant relative humidity of 90% and V_oc over 72 h at ambient condition.     

Reverse recovery transient characteristic of PEDOT:PSS/n-Si hybrid organic-inorganic heterojunction

We study the junction behavior of poly (3,4-ethylenedioxythiophene):polystyrenesulphonate/n-Si hybrid organic/inorganic heterojunction by reverse recovery transient (RRT) characterization. RRT response for PEDOT:PSS/n-Si hybrid junction is reported for various n-Si doping concentration and forward bias current injection level. The presence of settling time of 8.3–23.5 μs in the RRT response in contradiction to Schottky junction model commonly assumed for PEDOT:PSS/n-Si hybrid structure. The decrease in the minority carrier lifetime from 126.8 μs to 39.5 μs with increased n-Si doping concentration, suggests that minority carriers are stored at n-Si side of the junction, which is consistent with a p⁺-n junction model for the hybrid structure. The minority carrier lifetime is found to depend on forward bias current injection level, attributed to trap-saturation effect of the recombination-centers at the PEDOT:PSS/n-Si junction. The DC-IV characteristics of the PEDOT:PSS/n-Si hybrid junction are also consistent with the notion of diffusion and trap assisted recombination dominated dark current. The diffusion dominated transport of PEDOT:PSS/n-Si leads to an ideal p⁺-n junction behavior that leverages on the good transport properties of Si. Our findings are important in the modeling and optimization of the characteristics of electronic devices based on the organic/Si hybrid junction.