Absorption of carbon dioxide in aqueous colloidal silica solution with NaOH

The absorption rate (R _A ) of carbon dioxide was measured into an aqueous nanometer-sized colloidal silica solution of 0–31 wt% and NaOH of 0–2 kmol/m³ in a flat-stirred vessel for various sizes and speeds of 25 °C and 101.3 N/m² to obtain the volumetric liquid-side mass transfer coefficient (k _L a _L ) of CO₂. The film theory accompanied by chemical reaction between CO₂ and NaOH was used to estimate the theoretical value of absorption rate of CO₂. The empirical correlation formula containing the relationship between k _L a _L and rheological property of the aqueous colloidal silica solution was presented. The value of R _A in the aqueous colloidal silica solution was decreased by the reduction of k _L a _L due to elasticity of the solution.     

Absorption of carbon dioxide into aqueous colloidal silica solution with different sizes of silica particles containing monoethanolamine

Carbon dioxide was absorbed into an aqueous nanometer-sized colloidal silica solution in a flat-stirred vessel at 25 °C and 101.3 kPa to measure the absorption rate of CO₂. The concentrations of silica were in the range of 0–31 wt% and the sizes were 7, 60, and 111 nm. The solution contained monoethanolamine (MEA) of 0–2.0 kmol/m³. The volumetric liquid-side mass transfer coefficient (k _L a) of CO₂ was correlated with the empirical formula representing the rheological property of silica solution. The use of the aqueous colloidal silica solution resulted in a reduction of the absorption rate of CO₂ compared with Newtonian liquid based on the same viscosity of the solution. The chemical absorption rate of CO₂ was estimated by film theory using k _L a and physicochemical properties of CO₂ and MEA.     

Chemical Absorption of Carbon Dioxide into Aqueous Colloidal Silica Solution with Diethanolamine

Abstract

The chemical absorption rate (R_A) of CO₂ was measured into the aqueous nanometer sized colloidal silica solution of 0–31 wt% and diethanoleamine of 0–2 kmol/m³ in the flat‐stirred vessel with the impeller size of 0.034 m and its agitation speed of 50 rev/min at 25°C and 0.101 MPa, and compared with the values estimated from the model based on the film theory accompanied by chemical reaction. The value of the volumetric liquid‐side mass transfer coefficient (k_La) of CO₂, which was used to estimate the value of R_A, was obtained by the empirical correlation formula presenting the relationship between k_La and the rheological behavior of the aqueous colloidal silica solution. The value of R_A in the aqueous colloidal silica solution was decreased by the reduction of k_La due to the elasticity of the solution.     

Influence of polyethylene oxide on absorption of carbon dioxide into aqueous <Emphasis Type="Italic">N</Emphasis>-methyldiethanolamine solution

Carbon dioxide was absorbed into aqueous polyethylene oxide (PEO) solution containing N-methyldiethanolamine (MDEA) in a flat-stirred vessel to investigate the effect of non-Newtonian rheological behavior of PEO on the chemical absorption rate of CO₂, where the reaction between CO₂ and MDEA was assumed to be a first-order reaction with respect to the concentration of CO₂ and MDEA, respectively. A unified correlation equation containing the Deborah number, which reflects the viscoelastic properties of a non-Newtonian liquid, was used to obtain the volumetric liquid-side mass transfer coefficient of carbon dioxide in aqueous PEO solution. The elastic properties of PEO accelerated the absorption rate of CO₂ compared with that of a Newtonian liquid based on the same values of viscosity.     

Absorption of Carbon Dioxide into Aqueous Colloidal Silica Solution

Abstract

On the basis of experimental data for carbon dioxide absorption into aqueous nanometer sized colloidal silica solution as a non‐Newtonian fluid, a dimensionless correlation for volumetric liquid‐side mass transfer coefficient (k_La) of CO₂ in the flat‐stirred vessel was proposed. In addition to ordinary liquid properties and operating parameters such as impeller size and speed in the vessel, Deborah number, which is defined as the product of the characteristic material times of the liquid and agitation speed in the flat‐stirred vessel and represents the viscoelastic behavior of non‐Newtonian fluid, was used to present unified expressions for k_La in Newtonian as well as non‐Newtonian liquid. The values of k_La in the aqueous colloidal silica solution were reduced due to elasticity of the solution.     

Simultaneous absorption of CO<Subscript>2</Subscript> and SO<Subscript>2</Subscript> into aqueous AMP/NH<Subscript>3</Subscript> solutions in binary composite absorption system

To enhance the absorption rate for CO₂ and SO₂, aqueous ammonia (NH₃) solution was added to an aqueous 2-amino-2-methyl-1-propanol (AMP) solution. The simultaneous absorption rates of AMP and a blend of AMP+ NH₃ for CO₂ and SO₂ were measured by using a stirred-cell reactor at 303 K. The process operating parameters of interest in this study were the solvent and concentration, and the partial pressures of CO₂ and SO₂. As a result, the addition of NH₃ solution into aqueous AMP solution increased the reaction rate constants of CO₂ and SO₂ by 144 and 109%, respectively, compared to that of AMP solution alone. The simultaneous absorption rate of CO₂/SO₂ on the addition of 1 wt% NH₃ into 10 wt% AMP at a p _A1 of 15 kPa and p _A2 of 1 kPa was 5.50×10⁻⁶ kmol m⁻² s⁻¹, with an increase of 15.5% compared to 10 wt% AMP alone. Consequently, the addition of NH₃ solution into an aqueous AMP solution would be expected to be an excellent absorbent for the simultaneous removal of CO₂/SO₂ from the composition of flue gas emitted from thermoelectric power plants.     

氨基酸离子液体-MDEA混合水溶液对CO2的降膜吸收

氨基酸离子液体对CO₂吸收速度快,而N-甲基二乙醇胺（MDEA）有较高的CO₂吸收负荷,因此选用四甲基铵甘氨酸（［N₁₁₁₁］［Gly］）与MDEA水溶液复配成混合吸收剂用于CO₂的降膜吸收。用恒定容积法研究了混合吸收剂吸收CO₂的性能,实验结果显示,提高CO₂分压和增大［N₁₁₁₁］［Gly］浓度均能提高混合吸收剂对相似文献   

Absorption of Carbon Dioxide into Aqueous Xanthan Gum Solution Containing Monoethanolamine

Abstract

Carbon dioxide was absorbed into the aqueous xanthan gum (XG) solution in the range of 0–0.151 wt% containing monoethanolamine (MEA) of 0–2 kmol/m³ in a flat‐stirred vessel with the impeller of 0.05 m and agitation speed of 50 rpm at 25°C and 0.101 MPa to measure the absorption rate of CO₂. The volumetric liquid‐side mass transfer coefficient (k_La_L) of CO₂ decreased with increasing XG concentration, and was correlated with the empirical formula having the rheological behavior of XG solution. The chemical absorption rate of CO₂ was estimated by the film theory using the values of k_La_L and physicochemical properties of CO₂ and MEA. The aqueous XG solutions made the rate of absorption of CO₂ accelerated compared with the Newtonian liquid based on the same viscosity of the solution.     

The physical solubilities and diffusivities of N<Subscript>2</Subscript>O and CO<Subscript>2</Subscript> in aqueous ammonia solutions on the additions of AMP,glycerol and ethylene glycol

Carbon dioxide (CO₂) is a major greenhouse gas, the emissions of which should be reduced. There are various technologies for the effective separation of CO₂. Of these, chemical absorption methods are generally accepted as the most effective. The monoethanolamine (MEA) process is an effective way to remove CO₂, but is an expensive option for the separation of CO₂ from massive gas-discharging plants. Therefore, ammonia solution, which is less expensive and more effective than MEA, was used for the removal of CO₂. In this study, the physical solubility of N₂O in (ammonia+water), (ammonia+2-amino-2-methyl-1-propanol+water), (ammonia+glycerol+water) and (ammonia+ ethylene glycol+water) was measured at 293, 303, 313, 323 K. Additive concentrations of 1, 3, and 5 wt% AMP, glycerol and ethylene glycol were added for each 9 wt% ammonia solution. A solubility apparatus was used to investigate the solubility of N₂O in ammonia solutions. The diffusivity was measured with a wetted wall column absorber. The “N₂O analogy” is used to estimate the solubility and diffusivity of CO₂ in the aqueous ammonia solutions. OriginPro 7.5 was used to correlate the solubility and diffusivity of N₂O in ammonia solutions. The parameters of the correlation were determined from the measured solubility and diffusivity.     

Transfer rate measurement of lysozyme by liquid-liquid extraction using reverse micelles with dense CO2

Lysozyme was extracted from aqueous solution into i-octane using reverse micelles in the presence of pressurized CO₂. A squat vessel with two independent stirrers was used to measure the mass transfer of the lysozyme across a planar interface. Mass transfer coefficient, k _L of the lysozyme from the aqueous to the organic phase was measured at selected ionic strengths, pH, sodium bis(2-ethylhexyl) sulfosuccinate (AOT) surfactant concentrations, temperatures and pressurized CO₂. The mass transfer rate of lysozyme was higher in high temperature (318 K) and pressure (20MPa). pH of 9 in aqueous phase showed highest mass transfer rate of lysozyme. The application of pressurized CO2 markedly increased the mass transfer rate of lysozyme comparing to conventional non-pressurized system.     

Automated measurements of gas‐liquid mass transfer in micropacked bed reactors

Gas‐liquid mass transfer in micropacked bed reactors is characterized with an automated platform integrated with in‐line Fourier transform infrared spectroscopy. This setup enables screening of a multidimensional parameter space underlying absorption with chemical reaction. Volumetric gas‐liquid mass‐transfer coefficients (k_La) are determined for the model reaction of CO₂ absorption in a methyl diethanolamine/water solution. Parametric studies are conducted varying gas and liquid superficial velocities, packed bed dimensions and packing particle sizes. The results show that k_La values are in the range of 0.12～0.39 s^?1, which is about one‐to‐two orders of magnitude larger than those of conventional trickle beds. An empirical correlation predicts k_La in micropacked bed reactors in good agreement with experimental data. © 2017 American Institute of Chemical Engineers AIChE J, 64: 564–570, 2018     

Interfacial area and volumetric mass transfer coefficient in a bubble reactor at elevated pressures

The present study deals with the pressure effects on mass transfer parameters within a bubble reactor operating at pressures up to . The gas-liquid systems are N₂/CO₂-aqueous solution of Na₂CO₃-NaHCO₃ and N₂/CO₂-aqueous solution of NaOH. A sintered powder plate is used as a gas distributor. Three parameters characterizing the mass transfer are identified and investigated with respect to pressure: the gas-liquid interfacial area a, the volumetric liquid side mass transfer coefficient k_La and the volumetric gas side mass transfer coefficient k_Ga. The gas-liquid absorption with chemical reaction is used and the mass transfer parameters are determined by using the model reaction between CO₂ and the aqueous solutions of Na₂CO₃-NaHCO₃ and NaOH. For a given gas mass flow rate, the interfacial area as well as the volumetric liquid mass transfer coefficient decrease with increasing operating pressure. However, for a given pressure, a and k_La increase with increasing gas mass flow rates. The mass transfer coefficient k_L is independent of pressure. Furthermore, the pressure increase results in a decrease of k_G and k_Ga for a given gas mass flow rate. The values of the interfacial area, which are obtained from both chemical systems are found to be different. These discrepancies are attributed to the choice of the liquid system in the absorption reaction model.     

Effects of moderate pressure on premeability and viability of <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis> cells

With CO₂ and N₂ as the pressure media, the effects of the moderate pressure (0.1–1.0MPa) and the holding time on the conductivities of the cell suspension of Saccharomyces cerevisiae CICC1447 and Saccharomyces cerevisiae CICC1339, as well as the absorbances of the supernatant (after centrifuged) at 280 nm (A₂₈₀) and 260 nm (A₂₆₀) were determined. The membrane permeability of Saccharomyces cerevisiae CICC1447 increased significantly and the cell leakage was aggravated with the pressure increase. For Saccharomyces cerevisiae CICC1339, the conductivity of the cell suspension, A₂₈₀ and A₂₆₀ of the supernatant fluctuated with the pressure increase; as a whole, they increased with pressure. Different from high pressure, a moderate pressure not only remarkably improved the permeability of the yeast cell membrane, but also kept yeast cell viability; moreover, the integrity of the yeast cell membrane could be maintained. The first author and the fifth author contributed to the work equally.     

Interfacial Area and Liquid‐Side Volumetric Mass Transfer Coefficient in a Downflow Bubble Column

An experimental investigation was made to measure interfacial area, a, and liquid‐side volumetric mass transfer coefficient, k_La, in a downflow bubble column by chemical methods viz., absorbing CO₂ in aqueous sodium hydroxide and sodium carbonate/bicarbonate buffer solution respectively. The effect of gas and liquid flowrate and nozzle sizes on a and k_La were investigated. The experimental data obtained in the present system were analyzed and correlations were developed to predict a and k_La in terms of superficial gas velocity. The variation of a and k_La with specific power input were shown in graphical plot and compared with other gas‐liquid systems.     

Comparison of effective interfacial areas with the actual contact area for gas absorption in a stirred cell

Experiments were carried out in a stirred cell with a flat gas-liquid interface to test the Danckwerts' plot method of measuring effective interfacial area A and physical mass transfer coefficient k_L. Pure CO₂ was absorbed into an aqueous solution of 0.5 mol Na₂CO₃ + 0.5 mol NaHCO₃ per liter, in the presence of a catalyst (arsenite or carbonic anhydrase). Contrary to the findings of Kon and Sandall [1], good agreement has been found between the measured areas and the actual contact area. The experiments of Kon and Sandall [1] are analysed critically.     

Oxidation of p-methoxyphenol on SnO2–Sb2O5 electrodes: Effects of electrode potential and concentration on the mineralization efficiency

The oxidation of p-methoxyphenol in aqueous solution on antimony-doped tin oxide has been studied, and the effects of applied potential and initial PMP concentration upon the oxidation rate have been identified. The concentration decay of PMP during its electrooxidation follows first-order reaction kinetics. Analysis solution during electrolysis using UV–Vis spectroscopy revealed that under some experimental conditions partial oxidation of PMP occurs. The principal products were p-benzoquinone and aliphatic (maleic and oxalic) acids. The Faradaic efficiencies for oxidation at different applied potentials were determined from the UV–Vis spectra obtained. It is shown that production of CO₂ was very low at potentials below 2.3 V with respect to the saturated calomel electrode, and that at more positive potentials mineralization to CO₂ decreased as the concentration of PMP in solution increased.     

N<Subscript>2</Subscript>O fluxes and CO<Subscript>2</Subscript> exchange at different N doses under elevated CO<Subscript>2</Subscript> concentration in boreal agricultural mineral soil under <Emphasis Type="Italic">Phleum pratense</Emphasis>

The effects of elevated atmospheric CO₂ concentration on N₂O fluxes, instant CO₂ exchange and the biomass production of timothy (Phleum pratense) were studied in the laboratory. Three sets of 12 farmed sandy soil mesocosms sown with Phleum pratense were fertilised with a commercial fertiliser in order to add 5, 10 and 15 g N m⁻², and equally distributed in four thermo-controlled greenhouses. In two of the greenhouses, the CO₂ concentration was kept at atmospheric concentration (360 μmol mol⁻¹), and in the other two at double the ambient concentration (720 μmol mol⁻¹). Forage was harvested and the plants fertilised twice during the N₂O measurements. This was followed by an extra fertilisation and harvesting. After the third harvest, the growth of P. pratense was maintained at a height of 18 cm for measurements of instant CO₂ exchange, performed in two growth chambers. N₂O exchange was monitored using a closed chamber technique and a gas chromatograph. Instant CO₂ exchange was monitored using an infrared gas analyser. N₂O was emitted from the soil in the low, moderate and high N treatments at both CO₂ concentrations when the moisture content was low, the N₂O probably being mainly derived from nitrification. The highest flux (3303 μg N₂O m⁻² h⁻¹) occurred in the highest N treatment before thinning the stand of P. pratense under elevated CO₂ concentration. P. pratense was acclimated to the elevated CO₂ concentration: the NEE and P _G of the elevated growth of P. pratense decreased, in contrast to the fluxes of the normal ambient growth, when measured at the changed CO₂ concentration (ambient). The rate of respiration (R _TOT) in the agroecosystem did not increase due to the elevated CO₂ concentration, but instead the results indicated decreased R _TOT (on average 2049 and 1808 mg CO₂ m⁻² h⁻¹ at ambient and elevated CO₂ concentration, respectively) when there was an abundant N supply. This infers the possibility of enhanced C accumulation in agriculture mineral soil via P. pratense under an increased atmospheric CO₂ supply.     

Activation of lipase by sol–gel coating with hydrophobic alkyl‐substituted silicates in supercritical carbon dioxide

BACKGROUND: Sol–gel entrapment of lipases is usually performed in an aqueous solution. A novel method of sol–gel coating of lipase in supercritical carbon dioxide (SC‐CO₂) is proposed. RESULTS: Crude lipase powder (Rhizopus oryzae) coated with hydrophobic silicates, derived from dimethyldimethoxysilane and tetramethoxysilane in SC‐CO₂ at 35 °C and 15 MPa, exhibited 5–7 times higher esterification activity than that prepared via an aqueous sol–gel route. Lipase immobilized in a methyl‐substituted silica monolith was also highly activated by sol–gel coating using the same silica precursors in SC‐CO₂. CONCLUSION: Sol– gel coating in SC‐CO₂, of lipases in powder and immobilized forms with hydrophobic alkyl‐substituted silicates provides an efficient tool for the enhancement of enzymatic activities in non‐aqueous media. Copyright © 2009 Society of Chemical Industry     

Reaction between Hydrosulfide and Iron/cerium (hydr)oxide: Hydrosulfide Oxidation and Iron Dissolution Kinetics

Hydrosulfide oxidation and iron dissolution kinetics were studied at normal pressure, under inert (N₂) atmosphere, in a liquid–solid mechanically-stirred slurry reactor. The kinetic variables undergoing variations were: hydrosulfide initial concentration (0.90–3.30 mmol/L), oxide initial surface area (16–143 m²/L) and pH (8.0–11.0). The hydrosulfide consumption and products (thiosulfate and polysulfide) formation were quantified by means of capillary electrophoresis, while iron dissolution was monitored through atomic absorption spectroscopy. Most of Fe(II) produced at pH = 9.5 remained associated with the oxide surface in the time-scale of the experiments. The hydrosulfide oxidation by the iron/cerium (hydr)oxide was found to be surface-controlled, with rates (R_i) of both sulfide oxidation and Fe(II) dissolution expressed in terms of an empirical rate equation: R_i = k_i[HS⁻]_t=0^−0.5[A]_t=0[H⁺]_t=0^−0.5 , where k_i represents the apparent rate constants for the oxidation of HS⁻ (k_HS) or the dissolution of Fe(II) (k_Fe), [HS⁻]_{t = 0} is the initial hydrosulfide concentration, [A]_{t = 0} is the initial Fe/Ce (hydr)oxide surface area and [H⁺]_{t = 0} is the initial proton concentration. The rate constant, k_HS, for the oxidation of hydrosulfide at pH = 9.5 was (3.4219 ± 0.65) × 10⁻⁴ mol² L⁻¹ m⁻² min⁻¹, with the rate of hydrosulfide oxidation being ca. 10 times faster than the rate of Fe(II) dissolution (assuming a 1:2 stoichiometric ratio between HS⁻ oxidized and Fe(II) produced; k_Fe = (3.9116 ± 0.41) × 10⁻⁵ mol² L⁻¹ m⁻² min⁻¹).     

Combined Absorption and Self-Decomposition of Ozone in Aqueous Solutions with Interfacial Resistance

A theoretical analysis is performed employing the film model for the isothermal absorption and self-decomposition of ozone in aqueous solutions with interfacial resistance, which is inversely proportional to the interfacial mass transfer coefficient k_s. A closed-form solution has been obtained. The effects of system parameters on the ozone mass transfer rate are examined. These parameters include the interfacial resistance (1/k_s), the acidic and basic self-decomposition reaction rate parameters (M_m ^0.5, M_n ^0.5.; M_m = [2D_Ak_mC_Ai ^m-1/(m+1)]/(k_L ⁰)², M_n=(2D_Ak_nC_Ai ^n-1/(n+1))/(k_L ⁰)², the reaction orders (m,n), the pH value of solution, and the liquid-phase mass transfer coefficient (k_L ⁰). The results indicate that the reduction effect of the interfacial resistance on the absorption rate is most significant for the situation with the larger values of M_m and M_n as well as with higher pH values. Also, for any particular finite value of k_L ⁰/k_s, the reduction effect encountered is greater for a gas liquid contactor with a lower k_L ⁰. The reduction effect should be avoided in order to maintain a higher mass transfer rate of ozone in aqueous solution. This analysis is of importance for the efficient use of ozone in water/wastewater treatment processes in the presence of interfacial resistance substances such as surface active agents. For some known special cases (for example, cases with no interfacial resistance), the present solution reduces to the previous works of other investigators.