New thermostable systems: structure/property relationships of nadic terminated telechelic fluorine polyimides

Polyimides were synthesized by polycondensation of nadic anhydride monoester (NE), hexafluoroisopropylidene-2,2-bis (phthalic acid anhydride) (6HFDA) and Cardo diamine in aprotic/polar medium. After examining the microstructure and the composition of systems with a polymerization index n̄ = 2.075 and 5.18 by high performance liquid chromatography (HPLC) and nuclear magnetic resonance (NMR) spectroscopy (¹H and ¹³C), their thermomechanical properties were investigated. The rheology curves obtained in the temperature range 50–400°C showed the presence of an α transition (glass transition temperature T_g) and a sub-glass β transition. The temperature of the maximum of the loss modulus G″ of these two transitions varied in the domain of molar mass M̄_n studied. The effect of endo/exo isomerization of the nadimide extremities on the values of the glass transition temperature has also been shown. When the percentage of exo isomer of a given polymer increased, the glass transition temperature T_g increased by 50°C.     

Dielectric behaviour of pure and nickel-doped cellulose acetate films

Pure and Ni (0·05%, 0·1% and 0·15%)-doped cellulose acetate (CA) films were formed on well-cleaned glass substrates using a solution growth technique. Metal–insulator–metal (MIM) sandwich structures of thin film capacitors were fabricated. Dielectric studies were carried out in the frequency range 1kHz to 10MHz in the temperature range 303–450K. The variation of capacitance and dielectric loss with temperature were studied at various frequencies. The variation of dielectric constants (ε′ and ε″) with frequency and temperature is discussed. An increase in capacitance with temperature was observed and this may be due to the chaotic oscillations of molecules in the polymer matrix. β (at lower temperature) and α (at higher temperature) relaxation loss peaks were observed. Doping results in the formation of charge transfer complexes/molecular aggregates in the polymer, which cause the shift of C_max value and the β and α relaxation loss peaks towards higher temperature. An appreciable dispersion of tan δ at lower frequency was noticed in all the samples studied. © 1998 SCI.     

About the activation energies of the main and secondary relaxations in cured styrene butadiene rubber

This article studies the influence of the network structure on the activation energies of the α and β relaxations in vulcanized styrene butadiene rubber, SBR. A cure system based on sulphur and TBBS (N‐t‐butyl‐2‐benzothiazole sulfenamide) was used in the formulation of several compounds cured at 433 K. The activation energies were evaluated from internal friction (loss tangent) data of the compounds using an automated subresonant forced pendulum in a wide frequency range and between 80 K and 273 K. The internal friction data of the samples reveal two transitions, α and β, characterized by the temperatures T_α and T_β, due to the glass transition and the phenyl group rotation of the copolymer, respectively. Although T_α increases at higher crosslink density, it shows also a dependence with the amount of polysulphide and monosulphide linkages present in the samples. The highest activation energy for this process is obtained for the samples with high crosslink density and 30% of monosulphides in this structure. In the case of the β‐relaxation, there is a pronounced change in the activation energy between the uncured and the cured samples. The type of structure formed during vulcanization has an important effect in the activation energy of the segmental mode‐process. In the case of the β‐process, the cis‐trans isomerization that takes place during vulcanization in the butadiene part of the SBR, might be the cause of conformational changes in the surrounding of the phenyl rings that affect the energy barrier associated to the phenyl rotation. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Structure/properties relationship of nadimide-terminated fluorinated polyimides. Part II. New thermostable systems

We have established the chemical structure/mechanical properties relationships of new nadimide-terminated polyimides. Initially, the prepolymers were synthesized by polycondensation of nadic anhydride (NA), hexafluoroisopropylidene-2,2-bis(phthalic acid anhydride) (6HFDA) and two phenylene diamines, meta (mPDA) and para (pPDA) in N-methylpyrrolidone (NMP). After characterizing the microstructure and composition of these systems using chromatographic (HPLC, SEC) and spectroscopic techniques (¹H and ¹³C NMR), we determined their thermomechanical properties. The rheology curves obtained showed the presence of two transitions, α and β, associated with the glass transition and a second, sub-vitreous transition, because of local molecular movements. By studying the relationship between chemical structures and mechanical properties, we have shown the influence of endo/exo isomerization of nadimide extremities on the glass transition temperature T_g. In a given polymer, the value of T_g increases with increasing percentage of exo isomers. ©1997 SCI     

Effect of the composition ratio of pimelic acid/calcium stearate bicomponent nucleator and crystallization temperature on the production of β crystal form in isotactic polypropylene

The influence of the composition ratio of pimelic acid/calcium stearate bicomponent nucleator on the β crystal form content of isotactic polypropylene (iPP) had been studied at the crystallization temperature of 120°C and duration of 30 min. It was found that the β crystal form content increased continuously with increasing amount of calcium stearate at the constant amount of 0.15% pimelic acid. High β crystal form content polypropylene could be produced when the amount of calcium stearate was greater than 0.30% (the mass composition ratio of pimelic acid/calcium stearate was less than 1/2, the mole ratio was less than 1.89/1). It was shown that pimelic acid and calcium stearate could react to produce a high effective β nucleator (calcium pimelate) “in situ” during the melt‐mixing of iPP and the bicomponent nucleator. The influence of crystallization temperatures (100–140°C) on the β crystal form content of iPP had also been studied at the constant composition ratio of 0.15% pimelic acid/0.5% calcium stearate (the calcium pimelate produced in situ was 0.16%, which was calculated from stoichiometry). It was found that the β crystal form content increased continuously with increasing crystallization temperature and it maximized at 130°C. β Crystal form content decreased sharply at the crystallization temperature of 140°C. It was shown that β → α modification transformed between 130 and 140°C. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Dynamic crystallization of polypropylene and wood‐based composites

Thermoplastic composites made of an isotactic polypropylene (iPP) matrix and woodflour (WF) were prepared by melt‐blending, using twin‐screw extrusion and injection molding. Up to 20 wt % of the composite was composed of WF. The incorporation of an interfacial agent made of an ethylene/methacrylic acid copolymer to iPP and WF, PP/WF, binary blends causes a compatibilization effect that becomes evident due to a reduction in the crystallization temperature of PP. In both the binary composites and the compatibilized or ternary composites, the PP adopts an α or monoclinic structure when crystallization occurs from the melt under dynamic conditions at cooling rates between 1 and 20°C min^?1. On the other hand, X‐ray diffraction analysis using synchrotron radiation of the injection‐molded samples demonstrates the existence of a β or trigonal form in the binary as well as the ternary PP/WF composites. They reach k_β levels between 0.18 and 0.25, which can be interpreted as the co‐operation between a reduction of the crystallization rate and the shear effect induced during the injection. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 6028–6036, 2006     

Effects of strain rate and comonomer on the brittle–ductile transition of polymers

The effect of rate on the brittle–ductile transition of polymers can be given by an Arrhenius-type equation with activation energy between those of α and β transitions and given by where E_b is the activation energy for brittle-ductile transition, E_α is that for α transition, E_β is that for β transition, T_g is the glass transition temperature, T_b is the brittle–ductile transition temperature at 0.1 min.^?1, T_α is the α transition temperature at 1 cps, and T_β is the β transition temperature at 1 cps. The plots of T_b versus the weight fraction (w) of comonomer are sigmoidal, with an inflection point at w = 0.5.     

Polyaniline doped with α, ω‐alkanedisulfonic acids: preparation and characterization

The use of α, ω‐alkanedisulfonic acid, HO₃S(CH₂)_nSO₃H (n = 1, 4, 6 and 12), as a dopant for polyaniline (PANi) was investigated. This series of disulfonic acids with varying chain lengths were synthesized and used in the doping of PANi. The doped polymers showed conductivity in the range 10^?2 to 10^?1 S cm^?1. Thermal studies showed that the doped polymers, depending on the chain length of α,ω‐alkanedisulfonic acid, were stable up to ca 300 °C and the thermal stability decreased with increasing dopant chain length. The thermal stability of α,ω‐alkanedisulfonic acid‐doped PANi was higher than that of alkanesulfonic acid‐doped PANi which typically degrades around 250 °C, suggesting a moderately broader processing window for α,ω‐alkanedisulfonic acid‐doped PANi for blending with other thermoplastics. Copyright © 2012 Society of Chemical Industry     

Chemical Synthesis of Rare Natural Bile Acids: 11α‐Hydroxy Derivatives of Lithocholic and Chenodeoxycholic Acids

A method for the preparation of 11α‐hydroxy derivatives of lithocholic and chenodeoxycholic acids, recently discovered to be natural bile acids, is described. The principal reactions involved were (1) elimination of the 12α‐mesyloxy group of the methyl esters of 3α‐acetate‐12α‐mesylate and 3α,7α‐diacetate‐12α‐mesylate derivatives of deoxycholic acid and cholic acid with potassium acetate/hexamethylphosphoramide; (2) simultaneous reduction/hydrolysis of the resulting △¹¹‐3α‐acetoxy and △¹¹‐3α,7α‐diacetoxy methyl esters with lithium aluminum hydride; (3) stereoselective 11α‐hydroxylation of the △¹¹‐3α,24‐diol and △¹¹‐3α,7α,24‐triol intermediates with B₂H₆/tetrahydrofuran (THF); and (4) selective oxidation at C‐24 of the resulting 3α,11α,24‐triol and 3α,7α,11α,24‐tetrol to the corresponding C‐24 carboxylic acids with NaClO₂ catalyzed by 2,2,6,6‐tetramethylpiperidine 1‐oxyl free radical (TEMPO) and NaClO. In summary, 3α,11α‐dihydroxy‐5β‐cholan‐24‐oic acid and 3α,7α,11α‐trihydroxy‐5β‐cholan‐24‐oic acid have been synthesized and their nuclear magnetic resonance (NMR) spectra characterized. These compounds are now available as reference standards to be used in biliary bile acid analysis.     

Synthesis of two modified carotenoids and their behavior during light exposure

Two modified carotenoids, β‐6‐hydroxy‐2, 5, 7, 8‐tetramethyl‐chromane carboxylic acid β‐apo‐8'‐carotenoate (Caro‐Trolox) and 3, 5‐di‐tert‐butyl‐4‐hydroxy benzoic acid β‐apo‐8'‐carotenoate (Caro‐BHT) were synthesized by esterification of β‐apo‐8'‐carotenol with Trolox and with 3, 5‐di‐tert‐butyl‐4‐hydroxy benzoic acid, respectively. Their activity under light exposure was examined comparatively to that of Trolox, α‐tocopherol, β‐carotene, β‐apo‐8'‐carotenoic acid (CA} and ethyl β‐apo‐8'‐carotenoate. The substrate used was purified sunflower oil. In the absence of a photosensitizer (240 W/m² , 25 °C) Caro‐Trolox (200 mg/kg) behaved as an antioxidant and was quite stable (1/5 of the initial amount remained after 2‐wk storage). Caro‐BHT (200 mg/kg) showed no antioxidant activity and was quite unstable (it was destroyed within 7 d). In the presence of 5 mg/kg chlorophyll α (12000 lx, 25 °C) similar observations were made. The activity of Caro‐Trolox was concentration‐dependent. At a 100‐mg/kg level of addition its activity was similar to that of the mixture of α‐t_copherol (100 mg/kg) and β‐carotene (10 mg/kg). Its performance at the 10‐mg/kg level was slightly better than that of the other carotenoids. The antioxidant behavior of the modified carotenoids was attributed to the presence of the phenolic moiety as supported by the results of the 1, 1‐diphenyl‐2‐picrylhydrazyl test (e.g. EC₅₀ after 15 min: 26.2, Caro‐Trolox; 35.8, Caro‐BHT; 122, CA; 22.3, Trolox).     

Effect of poly(vinylidene fluoride) polymorphic structures on the crystallization behavior of poly(butylene succinate)

The detail information of both α and β form poly(vinylidene fluoride) (PVDF) crystal effect on the crystallization behavior of poly(butylene succinate) (PBS) were systematically studied. The results show that β form PVDF can obviously improve the melt‐crystallization temperature of PBS during the nonisothermal crystallization process. Both crystallization time span and spherulitic size of PBS decrease with the increasing amount of β form PVDF, which enhances the primary nucleation of PBS. But α form PVDF shows no nucleating effect on PBS crystallization, exhibiting as almost unchanged T_c values for α form PVDF‐blended PBS samples. The intrinsic mechanism for the nucleating effect of β form PVDF on PBS was proposed to be the epitaxial crystallization. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40991.     

A comparative study on the selective hydrogenation of α,β unsaturated aldehyde and ketone to unsaturated alcohols on Au supported catalysts

The hydrogenation of trans,4-phenyl,3-buten,2-one (benzalacetone) and trans,3-phenyl, propenal (cinnamaldehyde) was carried out on Au supported on iron oxides catalysts. Commercial goethite (FeOOH), maghemite (γFe₂O₃) and hematite (αFe₂O₃) were used as supports. The catalytic activity of Au/Fe₂O₃ reference catalyst, supplied by the World Gold Council, was also investigated. Gold catalysts and the parent supports were characterized by BET, X-ray diffraction (XRD), temperature programmed reduction (TPR), temperature programmed desorption of ammonia (NH₃-TPD) and high resolution transmission electron microscopy (HRTEM).Among the catalysts investigated Au supported on FeOOH shows the highest activity and selectivity to UA in the hydrogenation of unsaturated carbonyl compounds whereas Au supported on αFe₂O₃ are the less active and selective catalysts.The catalytic activity and selectivity to unsaturated alcohols (UA) in the hydrogenation of benzalacetone and cinnamaldehyde are less influenced by the morphology of gold particles and are mainly influenced by the nature of the support.A correlation between the reducibility of the catalysts and the activity and selectivity to UA has been found. Increasing the reducibility of the catalysts both the activity and selectivity to UA increase. These results let us to argue that active and selective sites are formed by negative gold particles formed through the electron transfer from the reduced support to the metal.     

Discovery of α‐Substituted Imidazole‐4‐acetic Acid Analogues as a Novel Class of ρ1 γ‐Aminobutyric Acid Type A Receptor Antagonists with Effect on Retinal Vascular Tone

The ρ‐containing γ‐aminobutyric acid type A receptors (GABA_ARs) play an important role in controlling visual signaling. Therefore, ligands that selectively target these GABA_ARs are of interest. In this study, we demonstrate that the partial GABA_AR agonist imidazole‐4‐acetic acid (IAA) is able to penetrate the blood–brain barrier in vivo; we prepared a series of α‐ and N‐alkylated, as well as bicyclic analogues of IAA to explore the structure–activity relationship of this scaffold focusing on the acetic acid side chain of IAA. The compounds were prepared via IAA from l ‐histidine by an efficient minimal‐step synthesis, and their pharmacological properties were characterized at native rat GABA_ARs in a [³H]muscimol binding assay and at recombinant human α₁β₂γ_2S and ρ₁ GABA_ARs using the FLIPR? membrane potential assay. The (+)‐α‐methyl‐ and α‐cyclopropyl‐substituted IAA analogues ((+)‐ 6 a and 6 c , respectively) were identified as fairly potent antagonists of the ρ₁ GABA_AR that also displayed significant selectivity for this receptor over the α₁β₂γ_2S GABA_AR. Both 6 a and 6 c were shown to inhibit GABA‐induced relaxation of retinal arterioles from porcine eyes.     

Selective catalytic reduction by urea in a fluidized‐bed reactor

The selective catalytic reduction (SCR) of NO_x by urea as a reducing agent was carried out over fresh and sulfated CuO/γ‐Al₂O₃ catalysts in a fluidized‐bed reactor. The optimum temperature ranges for NO reduction on the fresh and sulfated CuO/γ‐Al₂O₃ catalysts were 300–350 °C and 400–450 °C, respectively. NO reduction with the sulfated CuO/γ‐Al₂O₃ catalyst was somewhat higher than that with the fresh CuO/γ‐Al₂O₃ catalyst. N₂O formation increased with increasing reaction temperature. Ammonia (NH₃) slip increased with increasing gas velocity and decreased with increasing reaction temperature. Copyright © 2003 Society of Chemical Industry     

Chemoenzymatic Preparation of Enantiopure Homoadamantyl β‐Amino Acid and β‐Lactam Derivatives

Racemic cis‐10‐azatetracyclo[7.2.0.1^2,6.1^4,8]tridecan‐11‐one was prepared from homoadamant‐4‐ene by chlorosulfonyl isocyanate addition. The transformation of the β‐lactam to the corresponding β‐amino ester followed by Candida antarctica lipase A‐catalyzed enantioselective (E>>200) N‐acylation with 2,2,2‐trifluoroethyl butanoate afforded methyl (1R,4R,5S,8S)‐5‐aminotricyclo[4.3.1.1^3,8]undecane‐4‐carboxylate and the (1S,4S,5R,8R)‐butanamide with>99% ee at 50% conversion. Alternatively, transformation of the β‐lactam to the corresponding N‐hydroxymethyl‐β‐lactam and the following Pseudomonas cepacia (currently Burkholderia cepacia) lipase‐catalyzed enantioseletive O‐acylation provided the (1S,4S,6R,9R)‐alcohol (ee=87%) and the corresponding (1R,4R,6S,9S)‐butanoate (ee>99%). In the latter method, competition for the enzyme between the (1R,4R,6S,9S)‐butanoate, 2,2,2‐trifluoroethyl butanoate and the hydrolysis product, butanoic acid, tended to stop the reaction at about 45% conversion and finally gave racemization in the (1S,4S,6R,9R)‐alcohol with time.     

Synthesis and Highly Stereoselective Hydrogenation of the Statin Precursor Ethyl (5S)‐5,6‐Isopropylidenedioxy‐3‐oxohexanoate

A search for the large‐scale preparation of (5S)‐5,6‐(isopropylidenedioxy)‐3‐oxohexanoates ( 2 ) – a key intermediate in the synthesis of pharmacologially important statins – starting from (S)‐malic acid is described. The synthesis of the required initial compound methyl (3S)‐3,4‐(isopropylidenedioxy)butanoate ( 1 ) by Moriwake’s reduction of dimethyl (S)‐malate ( 3 ) has been improved. Direct 2‐C chain elongation of ester 1 using the lithium enolate of tert‐butyl acetate has been shown to be successful at a 3‐ to 5‐fold excess of the enolate. Unfortunately, the product, tert‐butyl (5S)‐5,6‐(isopropylidenedioxy)‐3‐oxohexanoate ( 2a ) is unstable during distillation. Ethyl (5S)‐5,6‐(isopropylidenedioxy)‐3‐oxohexanoate ( 2b ) was prepared alternatively on a multigram scale from (3S)‐3,4‐(isopropylidenedioxy)butanoic acid ( 7 ) by activation with N,N′‐carbonyldiimidazole and subsequent reaction with Mg(OOCCH₂COOEt)₂. A convenient pathway for the in situ preparation of the latter is also described. Ethyl ester ( 2b ) can be advantageously purified by distillation. The stereochemistry of the catalytic hydrogenation of β‐keto ester ( 2b ) to ethyl (5S)‐5,6‐(isopropylidenedioxy)‐3‐hydrohyhexanoate (syn‐ 6 and anti‐ 6 ) has been studied using a number of homogeneous achiral and chiral Rh(I) and Ru(II) complexes with phosphine ligands. A comparison of Rh(I) and Ru(II) catalysts with (S)‐ and (R)‐BINAP as chiral ligands revealed opposite activity in dependence on the polarity of the solvent. No influence of the chiral backbone of substrate 2b on the enantioselectivity was noted. A ratio of syn‐ 6 /anti‐ 6 =2.3 was observed with an achiral (Ph₃P)₃RuCl₂ catalyst. Ru[(R)‐Tol‐BINAP]Cl₂ neutralized with one equivalent of AcONa afforded the most efficient catalytic system for the production of optically pure syn‐(5S)‐5,6‐isopropylidenedioxy‐3‐hydroxyhexanoate (syn‐ 6 ) at a preparative substrate/catalyst ratio of 1000:1.     

Synthesis of Fatty Acid Amides of Catechol Metabolites that Exhibit Antiobesity Properties

A series of fatty acid amides of 3,4‐methylenedioxymethamphetamine (MDMA) catechol metabolites were synthesized in order to evaluate their biological activities. Upon administration, all synthesized compounds resulted in negative modulation of food intake in rats. The most active compounds have affinity for the CB₁ receptor and/or PPAR‐α; part of their biological activity may be caused by these double interactions.     

Synthesis and characterization of novel biocidal cyclodextrin inclusion complexes grafted onto polyamide‐6 fabric by a redox method

The synthesis of immobilized β‐cyclodextrin derivatives onto polyamide‐6 fabric is presented. These novel fabrics were prepared by graft‐copolymerization of glycidyl methacrylate (GMA) onto polyamide 6 fabric, using a chemical redox system K₂S₂O₈/CuSO₄·5H₂O, followed by reaction of β‐cyclodextrins (CD) or monochlorotriazinyl (MCT β‐CD) with the GMA epoxy group. Some biocidal guests were complexed into CD cavity including p‐hydroxy benzoic acid, AgNO₃–ethanolamine mixture, iodine, N,N‐diethyltoluamide (DETA), citronella, jasmine, and sweet basil. Characterization of the novel fabrics was done by Fourier transform infrared spectroscopy (IR), electron scanning microscopy (SEM), and thermo gravimetric analysis (TGA). The biocidal activity of the grafted fabrics was tested against five strains of microorganisms. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 2586–2593, 2006     

Pristanic acid is activator of peroxisome proliferator activated receptor alpha

lsoprenoid phytanic acid (3,7,11,15‐tetramethylhexadecanoic acid) is degraded in peroxisomes by α‐oxidation to pristanic acid (2,6,10,14‐tetramethylpentadecanoic acid) and then via β‐oxidation. Branched‐chain phytanic acid is an activator of the peroxisome proliferator activated receptor α (PPAR ) which in liver cells regulates expression of genes encoding peroxisomal and mitochondrial β‐oxidative enzymes as well as cytosolic/nuclear liver‐type fatty acid binding protein (L‐FABP). In this report we address the question whether pristanic acid also acts as activator of PPARα and thus mediates the expression of its catabolizing enzymes. In a first in vivo approach we fed pristanic acid for 14 days to wildtype mice and to mice lacking sterol carrier protein 2/sterol carrier protein x which Ieads to a phenotype having high concentrations of branched‐chain fatty acids. In either genotype, feeding pristanic acid was associated with a strong induction of peroxisomal β‐oxidation enzymes tested (acyl‐CoA oxidase, bifunctional enzyme, thiolase) as well as of L‐FABP. The link between pristanic acid and protein expression observed was established by carrying out assays for transactivation of PPARα in transfected HepG2 cells. In comparison to hypolipidemic drugs and to straight‐chain fatty acids known to be PPARα agonists, branched‐chain phytanic and pristanic acids were substantially stronger activators, pristanic acid being even superior to phytanic acid.     

Evaluation of Variation in Protein Composition on Solubility,Emulsifying and Gelling Properties of Soybean Genotypes Synthesizing β' Subunit

The effects of subunit composition of two major proteins of soybean: glycinin (11S) and β‐conglycinin (7S) in nine different genotypes, on solubility and emulsifying and gelling properties at different pH (3, 5, 6, and 8) were examined. High‐protein genotypes (more than 40%) contained low amounts of the β′ subunit. The main factors influencing solubility at pH 6 were the content of α′, α (r = 0.89 and r = 0.91 at P < 0.05, respectively) and β′ subunit contents (r = ?0.71 at P < 0.05) of β‐conglycinin, while at pH 3 acidic subunits in glycinin had a positive correlation with solubility (r = 0.69 at P < 0.05). Emulsion activity at pH 6 was higher for genotypes synthesizing β′ subunit (r = 0.57 at P < 0.05). Genotypes synthesizing higher amounts of α′ and α subunit had higher emulsion stability at pH 6 (r = 0.85 and r = 0.92 at P < 0.05, respectively) and pH 8 (r = 0.91 and r = 0.97 at P < 0.05, respectively). The rheological measurements showed that genotypes with 11S/7S ratio higher than 2.2 formed gels with enhanced storage moduli. This influence was largely due to the high content of SH groups in glycinin acidic polypeptides resulting in stabilization of gels via disulfide bonding. Gels prepared from genotypes containing higher amounts of β′ subunit of β‐conglycinin exhibited reduced elastic properties. Genotypes showing better solubility also had higher emulsion stability, but formed weaker gels and had lower emulsion activity near neutral pH.