焊接参数对TC4薄板焊接过程的影响

目的 揭示焊接参数对TC4薄板焊接过程中温度场、位移场及应力场的影响规律。方法 基于有限元（FEM）模拟方法,运用Fortran语言对焊接热源及焊接参数进行定义,以模拟不同焊接参数下TC4薄板的TIG对接焊过程。结果 在稳弧阶段,温度场为一组以焊接方向为长轴的椭圆,且存在温度梯度,随着焊接速度的增大,温度场峰值、温度场温度梯度、熔池宽度和熔池体积逐渐减小,而焊接效率和焊接电流对温度场的影响与焊接速度刚好相反;随着焊接速度的增大,薄板最大变形量逐渐减小,焊接角变形及挠度变形逐渐得到改善,而焊接效率和焊接电流对位移场的影响与焊接速度刚好相反。在稳弧阶段,焊缝位置的残余应力为拉应力,两侧为压应力,随着焊接速度和焊接电流的增大,纵向残余拉应力逐渐增大,焊缝处高应力集中区的宽度逐渐减小,而焊接效率对应力场的影响与焊接速度刚好相反。在高焊接速度、中等焊接效率、低焊接电流参数条件下,可获得熔池体积小及熔池宽度窄的焊缝,有利于减小焊后残余应力与变形。结论 上述研究结果可为TC4薄板的焊接过程提供一定的理论指导。     

贯穿件环焊缝多道焊温度场数值模拟

以贯穿件构件为研究对象,运用ANSYS有限元分析软件,建立了其环焊缝多道焊温度场的有限元模型,采用双椭球热源模型,应用生死单元技术,利用ANSYS软件的APDL语言编写程序,实现了热源在环焊缝上的移动加载,模拟得到了贯穿件环焊缝多道焊焊接过程的瞬态温度场及各点的焊接热循环曲线.结果表明:模拟得到的温度场结果符合实际情况.多道焊温度场模拟方法能准确计算出其温度场,为以后研究贯穿件焊接过程的残余应力场数值模拟提供了依据.     

大厚度奥氏体不锈钢筒体填丝激光焊接变形和应力分析

目的 研究大厚度奥氏体不锈钢筒体填丝激光焊接,优化结构设计和工艺设计。方法 建立大厚度奥氏体不锈钢筒体填丝激光焊接数值分析模型,通过数值模拟的方法,定量分析大厚度奥氏体不锈钢筒体焊接变形和应力。结果 零件下部38 mm厚焊缝位置处的最大径向收缩量为1.2 mm;零件下部60 mm厚焊缝位置处的最大径向收缩量为2.0 mm;零件中部60 mm厚焊缝位置处的最大径向收缩量为1.9 mm;零件上部60 mm厚焊缝位置处的最大径向收缩量为1.8 mm。填丝激光焊接轴向收缩量为0.55 mm。焊接残余应力最大值在450 MPa左右,应力主要分布在焊缝附近。热处理后,焊接残余应力都有明显降低,最大残余应力从450 MPa左右降低到200 MPa左右,焊接残余应力范围存在一定程度减小;焊接残余变形变化较小,热处理后某些位置的变形略微有所增大。结论 模拟结果表明,大厚度奥氏体不锈钢筒体填丝激光焊接变形和应力在可接受范围内,焊后热处理对释放残余应力有重要作用。     

大型纵向桁材式基座焊接变形仿真与控制

基于热弹塑性法对大型纵桁式基座焊接过程进行了有限元分析,采用双椭球热源计算了焊接温度场与应力场,获得了基座焊接残余应力分布及变形情况,并对比分析了圆筒单元4种焊接顺序和3种基座约束方式对焊接变形的影响。结果表明,在压条和定位焊双重约束条件下,按照“头尾交替斜对称”焊接,基座变形最小;优化焊接顺序和约束方式,可有效减小大型基座的焊接变形。     

焊接应力、焊接变形的产生和控制

影响焊接应力与变形的因素很多,最根本的原因是焊件受热不均匀,其次是由于焊缝金属的收缩、金相组织的变化及焊件刚性的不同所致。本文将主要讨论焊接残余应力、焊接残余变形的产生和控制。     

6061-T6铝合金中厚板-节点套多层多道焊数值模拟

为研究铝合金中厚板-节点套接头在多层多道焊后的残余应力和变形分布,本文基于ABAQUS软件建立了该接头三维有限元模型,采用双椭球热源、生死单元法以及顺序耦合法,对6061-T6铝合金中厚板-节点套多层多道焊进行数值模拟,并分析了接头的温度场,以及在夹具约束下的焊接残余应力及变形的分布情况。研究结果表明:数值模拟与实际接头的熔池形状吻合度较高;摆动焊接过程中温度曲线呈多峰结构;焊件的升温速率明显大于冷却速率,且冷却速率随时间逐渐减小;焊接残余应力主要集中在焊缝及夹具区域,且小于6061-T6铝合金在室温下的屈服强度;接头的最大横向残余应力为129.9 MPa,中厚板上的横向残余应力大于节点套上的横向残余应力;接头的最大纵向残余应力为132.9 MPa,沿焊接方向,焊缝处的纵向残余应力呈山峰状分布;该接头在Y轴方向上的变形最大,为1.494 mm,该接头的最终变形结果为上凸变形。     

Ti2AlNb合金电子束焊接头残余应力及变形的数值模拟

目的 研究平板对接电子束焊接过程中Ti2AlNb合金接头的残余应力及变形规律。方法 采用高斯圆柱体和高斯面组合热源模型模拟了6.6 mm厚的Ti2AlNb合金平板对接电子束焊过程,对比研究了高焊速高束流和低焊速低束流2种工艺参数下焊接接头的残余应力和变形分布规律,并用小孔法测量了焊缝中心及距焊缝中心10 mm位置的残余应力值。结果 在高焊速高束流参数下,获得了熔池体积小、熔池宽度窄(为3.62 mm)、深宽比高的焊缝;在该参数下焊缝横截面上的高应力集中区(应力在900 MPa以上)尺寸较小,其宽度仅为低焊速低束流参数下的89%;同时,在高焊速高束流参数下,焊缝法向变形最大值为0.79 mm,低于低焊速低束流参数下的0.82 mm;模拟计算所得残余应力与实测值的误差在5.64%以内。结论 高束流高焊速工艺具有热输入小、热量集中、加工效率高的特点,有助于获得高应力集中区域小、深宽比高、变形小的焊缝,比低束流低焊速工艺更具优势。     

机械挤压矫正焊接变形的模拟与试验研究

利用自制的夹具对机械挤压矫正薄板焊接变形的效果进行了试验研究.采用有限元分析方法对常规焊件和机械挤压焊件的应力应变场及残余变形进行了模拟.试验和模拟结果均表明,对焊件施加平行于焊缝方向的纵向挤压力能够有效矫正薄板焊件的失稳变形.在适当的挤压力下,在远离焊缝的区域产生了纵向压缩塑性应变,而焊缝区由焊接过程导致的塑性应变值没有发生变化.机械挤压法能够降低薄板焊件焊缝区的纵向拉应力水平是其能够矫正焊接失稳变形的原因.     

核电站控制棒驱动机构Canopy焊缝焊接温度场和应力-应变场模拟

目的 研究机加工和拉拔2种成形方式下得到的填充环对Canopy焊缝的影响,获取焊接焊缝成形、焊接残余应力和变形的相关数据,以指导Canopy焊缝焊接工艺。方法 采用数值模拟的方法,建立Canopy焊缝焊接数值分析模型,模拟焊接温度场、焊接残余应力和焊接残余变形。结果 拉拔成形环焊接熔池高度为9 mm,机加工成形环焊接熔池高度为8.3 mm;机加工成形环焊接最大残余应力为255.6 MPa,而拉拔成形环焊接最大残余应力为277.8 MPa,均出现在管座紧贴焊缝的位置;机加工成形环焊接残余变形为0.19 mm,拉拔成形环焊接残余变形为0.186 mm,最大残余变形均出现在焊接起始位置附近,在焊缝与管座交接的位置。结论 熔池形貌直接影响了热影响区域的大小,拉拔Y型环焊接熔池高度更大,焊接的热影响区域更大;拉拔Y型环焊接残余应力略大于机加工Y型环焊接残余应力;机加工成形环和拉拔成形环焊接残余变形相近。     

预拉伸控制铝合金焊接变形

在预拉伸应力作用下,焊接了厚度为4mm的5A05铝合金试板,通过焊接试板挠曲变形量的测定,探讨了预加拉应力对铝合金焊接变形的影响。试验结果表明,预拉伸焊接法可以有效减小铝合金薄板焊缝处的纵向挠曲变形量,在弹性应力范围内,随着预拉伸应力的增大,试板的焊接变形逐渐变小。初步分析认为,预拉伸应力扩大了高温下焊缝附近的塑性变形区,从而增强了冷却过程中该区域抗塑性拉应变的能力,减小了焊件的挠曲变形。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.